Attachment 9 March 2011 Incidents.pdf

Description Category Type Camera 1804 (BE1043 CPB Hall)

No video present.

CCTV

Camera 1855 (Mux for 1840-1854)

Camera has a distorted or no picture.

CCTV

Location - P-1 Garage Problem - No video Camera - 137

POC - CCTV

Room Number - 403A Zone - 1823 Problem - Zone Failure

POC C4 DAQ

Room Number - 525 Problem - When the space is put into access mode the alarm monitors can not clear the alarms

POC - AMAG OTHER

Rm 4400 Z1604 (P1)

Zone failure.

C4 DAQ

JP1 - Zone 1604 - Room 4400 - - All Alarm Communication was lost - tenants stayed over nite - Tenant made contact

Ticket Submitted by

POC C4 DAQ

Ref. Plant - The egress door is not working from the inside

AMAG ENTRY

Suite 312 - CGN West Tower - The motion detector is not working and needs to be replaced

AMAG OTHER

hours, O conducted a check of the emergencycall boxes at the The Pentagon Reservation.

Air Force Memorial call box #1

Pentagon Athletic Center blue call boxes at stairwells 77 and 78

The impound lot call box were functioning properly but the blue flashing light are inoperable

Emergency call boxes on the lower Metro bus platform #'s 1, 2 and 3 and upper Metro bus platform #'s 4, 5 and 6 can call out but "error tones" iare received.

The Air Force Memorial call box #'s 2, 3, 4, 5, and 6 received no dial tone

The Pentagon Athletic Center red emergency call boxes at stairwells 77 and 78 upper and basement rings, but no one answers

Call box #'s 3A, 6A and 6C inoperable

The slug lane emergency call box located at lane 35 rings, but no answer

AMAG OTHER

5E407

Tenants badge was working, but now he's being denied swipe access.

AMAG ENTRY

MB757 - Tenants cannot fetinto this space - This is a Fire Pump Room and Access is needed

NOTE: ***Tenant stated that this is a DAQ Card Swipe Reader*** AMAG ENTRY Room Number - 3B548 Problem - Can't Access

POC

POC is located in room number - 1C765 AMAG ENTRY

Room Number - 2E1008 Problem - Door release and the camera has no power

POC -

Call POC before arrival AMAG OTHER 5C559

Node timed out.

AMAG AMAG

Location - 3rd Floor fourth wing Problem - Can't Access

POC - AMAG ENTRY

Locatin - The Fence under the Corridor 3 bridge where the Officer is located Problem - The maglock has fallen off

POC - AMAG LOCK

Room Number - 2C514 Problem - The keypad is stating that the room is secured but the room is not secure

POC - AMAG OTHER

Zone 1727 - Room 1012 - ZOne is in failure DRS Technician was notified

POC

SUbmitted by C4 DAQ 1E1037 - The keypad is dead and we cannot turn off the alarm

AMAG ENTRY

MEF - Turnstile 4 is not working at the Metro Ent.

AMAG TURNSTILE

5E541 - Node timed out

AMAG AMAG

3D648 - Tenants cannot access space - Only one person is able to access space and all other tenants cannot.

AMAG AMAG

Room Number - 5E129 Problem - Alarm is not functioning properly

POC - AMAG ALARM

Room Number - 204 Problem - Alarm is not functioning properly

POC -

ALT POC

Card Reader is not functioning. Not allowing entry. AMAG ALARM Room Number - 1530 Zone - 975 Problem - Keypad needs to be reset

POC - C3 DAQ

Location - River Moat Camera - 1057 Problem - Bad Video

POC CCTV

Location - Pac Server room Problem - The UP'S is bad

POC - CCTV

Location - PLC 2 Problem - All three turnstile are not working

POC AMAG TURNSTILE

Room Number - 1F1084 Problem - Printer at station 2 is not working properly its pritner badges with yellow and black lines

POC - AMAG COMPUTER

Location - 3rd Floor 4th Wing Center Stairwell Problem - Card Reader is not working properly

POC - AMAG ENTRY

Room Number - 2C448 and 2C453 Problem - Card Reader has no power

POC - AMAG ENTRY

Room Number - 5B546 Problem - Node TImed Out

POC - AMAG AMAG

Room Number - 3403 Problem - Card Reader is not working tenants can't get access

POC - AMAG ENTRY

DAQ C3 needs reset in the IEOC C3 DAQ COMPUTER 400 Army Navy Drive pols 1 through 8 went into failure, and will not recover. DRS technician was notified.

Submitted by C3 DAQ Location - Corridor 8 Problem - Turnstile number 7 on the outbound side is not working

POC - AMAG TURNSTILE

1C547/1C518

Two tenants are not able to access the adjoining suites.

AMAG ENTRY

Trailer 9 Pen Ren walkway

Entrance reader is down. Tenants are not able to access through the walkway and there is no officer in that section to allow them entrance. Possible node timed out.

AMAG ENTRY

Post 7 Booth - The monitor is not working

CCTV

1B349 - The card reader is not working

POC AMAG ENTRY

1A322

Node timed out.

AMAG AMAG

Z1807 STE 100

Zone failure.

C3 DAQ ALARM

MF931A

Tenant is not able to access the space.

AMAG ENTRY

4e1055

Node timed out.

AMAG AMAG

Room Number - 1E941 Problem - The alarm is not functioning properly

Room Number - 400 Problem - Tenants are not able to get into the space by using there pic they have been informed by ACC to put in a trouble ticket.

POC -

POC would like for a tech to come out on Monday Morning 03-07-2011 at 0:800

AMAG ENTRY

Mil Court - The front door card swipe is not working tech was notified

Submitted

POC C4 DAQ

MEF - Turnstile 3 is Down/Not working

Submitted by AMAG TURNSTILE Corridor 3 Entrance - VIR Cannot log in to the system

AMAG COMPUTER

Corridor 8 Pre-Screen Door is it will not open/broken

Officer AMAG DOOR Corridor 8 - turnstile 4 is down

Submitted by AMAG TURNSTILE Zone 1914 - Suite 820 - The Keypad is not working for one tenant ACC advised tenant to call in a Customer Service Order

C4 DAQ

4B337

Green door release button is not working.

AMAG ENTRY

MEF - Turnstile 3 is not operating

AMAG TURNSTILE

2A678

Tenant previously had access to open/secure the space, but now does not.

AMAG ENTRY

Room 2301 - Badge is not working - ACC advised tenant to call in a work order

Tenant - AMAG ENTRY Ste 2301

Node timed out

AMAG AMAG

Tenants are not able to access this space (node timed out).

AMAG AMAG

Garage

Camera 1 is facing down and the panel is open.

CCTV

1D746 (

Swipe is not functioning correctly

AMAG ENTRY

Metro Ent

Turnstile 6 is down. Tenants are not able to swipe out.

AMAG TURNSTILE

Sub Zone 2510 - Room 710/711 - Zone is in failure

Submitted by

C3 DAQ ALARM

HRP 140E2 - The door will not secure

Submitted by

AMAG DOOR

MEF - PD are not working - The magnetic door holder is not working after the fire alarm test is completed. This is the second door from the left if you are looking out from the post.

Submitted by AMAG DOOR

JP 1 - Poll is in failure

Submitted by AMAG POLL Zone 200 - Room 511 - The release button is not working

C4 DAQ

4C947 - 4C943 - The card swipe has no power and the door bell does not work

AMAG ENTRY

z694 Ste 6000 (P1)

Comms failure on the zone.

C3 DAQ ALARM

5C653 - Swipe pin number is not working -tenant states this is the correct pin number and may need to be troubleshoot

AMAG ENTRY

4C943

Tenants are locked out of the space. There was no power to the swipe and another tenant left the room unattended, so now they are all locked out.

AMAG ENTRY

1B349 - The C4 system is locked and will not allow anyone to access

C4 DAQ

FOB 2 South Gate Ped Booth - VIR is not working - the computer is not working/will not turn on at all

AMAG OTHER

Corr 3 Pre Screen Entrance

IEOC informed the officer that they were receiving a duress from that location. The officer advised that they don't see it, but would still like for it to be checked.

AMAG ALARM

Tolleyville Gate (N. Parking side) Ped. Ent.

Trailer door

Tenants are not able to swipe in through this entrance.

Ste 9030

Tenant can not access the space, but can access the scif.

C3 DAQ ENTRY

Ste 114

Tenant is not able to access the space.

C4 DAQ

3C639

Possible short in the card swipe.

AMAG ENTRY

Main Lobby Turnstile is not working

AMAG TURNSTILE

5D652

Tenant says that node (swipe) was just recently replaced and now some tenants are not able to either open or secure the space.

AMAG ENTRY

100A

Tenant with a renawal badge is not able to access or secure the space.

AMAG ENTRY

IEOC

Inside reader is not functioning

AMAG ENTRY

MEF Turnstiles 6 are down at the Metro

AMAG TURNSTILE

Suite 9100 - Ai Phone system is not currently working

AMAG AIPHONE

Zone 971 - Closet in the hallway - will not accept anyones swipe

C4 DAQ

Room Number - 4D247 Problem - Can't Access

POC - AMAG ENTRY

1E169 - The Front door was adjusted on Friday, March 4 because it slammed shut with too much force and it would cause the walls to shake. Now the front door does not latch when closed

AMAG DOOR

2A514B

Tenants can not access the space. They aren't locked out, but no one can access.

AMAG ENTRY

Room Number - 5C348A Problem - Maglock is not securing properly

POC - AMAG LOCK

3B1056

Reader is not working.

AMAG ENTRY

Card reader is loose and dangling from room 1C849A. This particular door is located out near A and E Drive when walking from from A Ring to C Ring. Reattach or replace cardreader. AMAG DOOR Location - Corridor 3 Problem - The duress alarm keeps going off at corridor 3 and the doors keep closing on there own

POC - AMAG ALARM

Room Number - 5E542 & 5E524 Problem - Node Timed Out

POC - AMAG AMAG

Location - MEF Problem - Turnstile number 3 is inoperable

POC - AMAG TURNSTILE

Room Number - 1B349 Problem - BOSCH ANALYTICS CCTV

COMPUTER IS REBOOTING

CONSTANTLY

POC - CCTV

1B349 - BOSCH ANALYTICS CCTV

COMPUTER IS REBOOTING

CONSTANTLY. EMAIL SENT AMAG

Location - Main Lobby Problem - Monitor number 4

POC - CCTV CCTV

Location - Corridor 3 Problem - Turnstile number 3

POC - AMAG TURNSTILE

Room Number - 8025 Problem - Maglock is loose

POC - AMAG LOCK

Location - Corridor 3 Pre Screen Problem - Duress alarm keeps going off

POC - AMAG ALARM

4C549, 4C516 - Tenant lost access and cannot get into the room

Security Manager Tenant AMAG ENTRY 1A349 - The back door is not working and will not release

Submitted by 1 AMAG DOOR

Location - MEF Problem - Turnstile number 8 is inoperable

POC - AMAG TURNSTILE

Location 7th Floor Problem - Can't Access

POC AMAG ENTRY

Room Number - 1B349 Problem - The fourth inside card reader is not working

POC - AMAG ENTRY

Room number - 5C520 Problem - Area is going into alarm

POC - AMAG ALARM

Room Number - 2E460 Problem - Node Timed Out

POC - AMAG AMAG

JP1 Poll is in Failure - Room 4400 - Zone

Submitted by C4 DAQ Corridor 8 - VIRS system is down

Officer on Duty AMAG COMPUTER MEF - Turnstile 3 and 8 are not working

Submitted by AMAG TURNSTILE

Power surge at approximately 5:25 this morning. POC states that the IEOC cannot see any activity.

Room 45011 Zone 1697 Room 47211 Zone 1700 Room 47231 Zone 1729 Room 47251 Zone 1695 Room G7281 Zone1708 Room 44011 Zone 1693 Room 43041 Zone 1832 Room 40161 Zone 1734 Room 27022 Zone 1699

AMAG AMAG

Mall Ent. VIR is not operating

AMAG COMPUTER

Corridor 3 - Turnstiles need to be cleaned

AMAG TURNSTILE

Front Turnstiles - All Turnstiles - are not working for new badges

AMAG TURNSTILE

3rd Floor - The card swipe is not working

Tenant has requested Pedro Cuello AMAG DOOR Location - 4th Floor Problem - Can't Access

POC - AMAG ENTRY

Room Number 100A Problem - Can't Access

POC -

POC would like for a tech to come out at 15:00 hours C3 DAQ Room Number - 1E744A Problem - The door is not securing

POC - AMAG OTHER

Lcoation - Vehicle gate for PenRen Problem - Card Reader is not working

POC - AMAG ENTRY

BE833 - Card swipe is not working - and no one can get in

AMAG ENTRY

ME800 - Zone 56 - Room is in failure

Submitted by C4 DAQ DVR needs to be replaced. CCTV

2A476 - Card swipe is not working

Zone 2543 - Zone will not arm - maybe the PIR or BMS

2850 Eisenhower Ave

C4 DAQ

1E525

Node timed out

AMAG AMAG

Room Number - 3B255 Problem - Tenants can not access the space when using there pic's

POC - AMAG ENTRY

PLC 2 MHA855

Turnstiles are down

AMAG TURNSTILE

Army G2 2D350

Lost video in all cctv cameras

CCTV

Room Number - 2416 Problem - Door Release button is not working

POC - AMAG ENTRY

Room Number - 4B288 Problem - Node Timed Out

POC - AMAG AMAG

NMCC - Tenant states that the AMAG system would not generate history reports

Submitted by AMAG ALARM MEF - Turnstile 3, 9, 10 and 13 are down

Submitted by AMAG TURNSTILE

Zone 473 - Suite 104 - Panlel is off on the time/The time has to be reset on the Keypad

C3 DAQ ENTRY

Location - Corridor 3 Problem - Turnstile number 1 and 3

POC - AMAG TURNSTILE

MEF - 2, 3, 11 Turnstiles are down

Submitted by AMAG TURNSTILE Location - Pentagon Village Problem - Maglock is not securing on the door

POC - AMAG LOCK

Room Number - 510 Problem - Node Timed Out

POC - AMAG AMAG

RSAC 1E712

Swipe access is not working. Tenant says that when they swipe it constantly beeps and does not allow them to input their number.

Tenant says that he will have to bring tech up from 1D716

AMAG ENTRY

Room Number - 3412 Problem - The monitor is blank

POC -

1A912 - Node timed out

Submitted by AMAG AMAG 1F1076 - Node timed out

Submitted by AMAG AMAG 5A286A - Node timed out

Submitted by AMAG AMAG 3D919 - Node timed out

Submitted by AMAG AMAG 5E670 - Node timed out

Submitted by AMAG AMAG 5C684 - Node timed out

Submitted by AMAG AMAG 5D647 - Node timed out

Submitted by AMAG AMAG 5A666 - Node timed out

Submitted by AMAG AMAG 5E610 - Node timed out

Submitted by AMAG AMAG

5D519 - Node timed out

Submitted by AMAG AMAG 5E573 - Node timed out

Submitted by AMAG AMAG 5B546 - Node timed out

Submitted by AMAG AMAG Room Number - 3619 Problem - Card Reader needs to be reset

POV -

AMAG OTHER

Room #1D749 Card reader inoperative, not working, no lights after several swipes to enter. This office space belongs to ger. AMAG ENTRY

Perimeter Door #10302, 1st Floor, 3rd Corridor near the PPD Officer post is unsecure. The Card reader seems to be working however the Maglock doesn't secure the door. Green light comes on after a card is swiped but the door remains unsecure. AMAG DOOR Room Number - 3A866 Problem - Door handle is stuck

POC - AMAG OTHER

Room Number - 509 Problem - Card Reader is offline

POC - AMAG OTHER

Location - PAC Trailer Problem - CCTV Monitor is not working properly

POC -

Room Number - 5E254 Problem - Node Timed Out

POC -

Corridor 3 - Turnstiles are down - All Turnstiles are down

AMAG TURNSTILE

JP1 - Poll is down

Submitted by C4 DAQ BC771 - Zone 309 - Alarm Monitors have received over 300 alarms from this room in less then 1 minute

Server Room - Bad video Jet

Submitted by CCTV Server Room Bad video Jet

Submitted by CCTV Server Room Bad video Jet

Submitted by CCTV Bad Keyboard

Submitted by CCTV Room 509/f Area - 5th Floor - The swipe pad is not working system states offline

POC K

Submitted by

AMAG ENTRY

Room Number - 3228 Problem - Node Timed Out

POC -

AMAG AMAG

Room Number - 5E858 Problem - Card Reader needs to be reset

POC - AMAG ENTRY

Room Number - 2E689 Problem - Can't Access

POC - AMAG ENTRY

The CCTV monitor and controls aren't working properly. A bad power source is the possible cause. Onsite POC:

CCTV monitor at the security desk in the lobby is inoperative.

Room Number - 5D337 Problem - Maglock is not working properly

POC AMAG LOCK

CCTV monitor at the security desk in the lobby is inoperative. Onsite

Location: JP1 5E518

Tenant says that the doorbell will ring for 5 minutes at a time. Also, they are not able to disarm the space.

Room Number - 2B546A Problem - The inside Keypad is not working properly

POC - AMAG ENTRY

Location - 4th Floor Problem - Can't Access

POC - AMAG ENTRY

Room Number - 1B473A Problem - Card Reader is offline

POC - AMAG ENTRY

ME745 - The Plate that holds the Maglock on the inner door fell off and needs to be replaced/repaired

AMAG

RDF - 1J670B - Door is not securing at night

POC AMAG LOCK

Room Number - BE879 Problem - Amag system is down

POC - AMAG AMAG

Location - PAC Problem - Camera 1702 is blurry. 1704, 1705 and 1713 No video

POC -

CCTV

Location - Corridor 5 Lobby Camera - 1093 Problem - No video

POC -

CCTV

Location - Corridor 4 Lobby Camera - 1412 Problem - No video

POC - 3

CCTV

Location -MEF Sidewalk Camera - 1649 Problem - Camera is blurry

POC -

CCTV

Location -MEF Visitor Booth Camera - 1650 Problem - No video

POC -

CCTV

G510 - CCTV Monitors are not wortking, Some are frozen on place, some are not showing any activity when someone is there and some have distored images

POC CCTV

Room Number - ME800 Zone - 56 Problem - PIN Duress

POC - C4 DAQ

Room Number - 5D1050 Problem - Can't Access

POC - AMAG ENTRY

Location - Corridor 3 Problem - Door is not securing properly

POC - AMAG DOOR

Room Number - RDF1J661 Problem - Nopde Timed Out

POC -

POC would like for a tech to come out on 03/17/2011 at 11:00 am AMAG AMAG 1D557 - This room is associated with military security force ( JS ). The room is offline, and can't monitor the alarm. The military security force is providing security checks for that space. AMAG ALARM Zone Number 1727 - Room Number 1012 - The room will not secure

Submitted by C4 DAQ Mall Veh Booth - VCS is not working

Submitted by AMAG COMPUTER Corridor 8 Ent. - Turnstile is not working

AMAG TURNSTILE

Room number - 1B514 Problem - Node Timed Out

POC - AMAG AMAG

Room Number - 1E532 & 1E525 Problem - Can't Access

POC - AMAG ENTRY

Room Number - BC932 Problem - Node Timed Out

POC - 1 AMAG AMAG

Room Number - 3619 Problem - POC Can't Access

POC - AMAG ENTRY

Location - NMCC Post 2 Problem - CCTV monitor is not working properly

POC - CCTV

PD 10503 - PD will not physically secure

Submitted by AMAG DOOR Zone 605 - Suite 900 - The door is physically locked the keypad malfunction

Submitted by C3 DAQ ENTRY Corridor 3 - VCS system is locked

AMAG COMPUTER

RSAC - The front door is not locking

AMAG DOOR

1B349 - AI Phone is not working to view or buzz people in

AMAG AIPHONE

Visitor Center - VCS is not connected to the network

POC

Submitted by AMAG COMPUTER

Suite 400 - The door is alarming and the door is activated with a key now and the door has a bar, the push bar is not working

AMAG ALARM

Room Number - 3412 Problem - CCTV monitor is blank

POC - CCTV

Location - The 6th Floor Problem - Card Reader is not working properly

POC - AMAG ENTRY

Location - Main Lobby Problem - Amag monitoring station continues to go down and they can not bring it back up

POC -

AMAG AMAG

Location - RDF Door 2 Problem - Maglock is not securing the door

POC - AMAG LOCK

JP1 - Poll is i n failure

1D557 and 1C554 - Tenant states that room are showing offline Militaey Security Forces P1

Submitted by

AMAG ALARM

1E735A - Keypad malfunction

POC

Submitted by AMAG ENTRY

JP1 - Monitor for CCTV system is inoperable

No POC Listed No Contact Number Provided Submitted by CCTV Corridor 3 VCS system is down

AMAG COMPUTER

1E735A - Keypad is not working - Keypad is located inside the scif

Submitted by AMAG ENTRY 3C636 - Can not get into room - Node is timed out

- Tenant is standing in the hallway and there is not number listed AMAG AMAG RDF Entrance - VCS is not working

Submitted by AMAG COMPUTER Room number - 5D453 Problem - Door Buzzer is not working properly

POC - AMAG ENTRY

NCC 4B556

Smart UPS needs to be replaced.

AMAG BATTERY

2D531

Node timed out.

AMAG AMAG

P1 Garage - ramp side

Tenant says that the timers have been thrown off and they are now locked in.

C3 DAQ ENTRY

Location - Corridor 3 Problem - The first turnstile closer to leaving out of corridor 3 the card reader has no power

POC AMAG TURNSTILE

1E712 - RSAC - Keypad is not working

POC

Submitted by AMAG ENTRY Mux - C7 is in failure

Submitted by C4 DAQ Poll 1 is down

Submitted by C4 DAQ Corridor 3 - all Turnstiled is down

Submitted by AMAG TURNSTILE 1B349 - AMAG Workstations 338 & 336 are not operating

Submitted by AMAG AMAG 1B479

No power to the swipe.

AMAG ENTRY

PLC - Turnstiles are not working

AMAG TURNSTILE

Room Number - 515 Zone - 200 Problem - Card Reader is not working properly

POC - C3 DAQ ENTRY

Corr 8

Turnstiles 5 and 7 are having swipe issues.

Officers have to manually open the turnstiles. AMAG TURNSTILE Room Number - 42143 Zone - 1740 Problem - Zone Failure

POC -

POC C4 DAQ

Room Number - 40231 Zone - 1737 Problem - Zone Failure

POC C4 DAQ

Room NUmber - 5E621 Problem - THE HANDICAP CR/KP IS

TIMED OUT. ICHECKED THE KEYPAD

AND THERE WAS NO TONE. PANEL

NEEDS TO BE REFRESHED SO DOWN

LOAD WILL TAKE.

POC - AMAG ENTRY

Room Number - 1273 Problem - Alarm is going on and off in the area

POC - AMAG ALARM

Room Number - 4E756 Problem - AI Phones are not working

POC AMAG AIPHONE

512A - 1726 and 1723 - Alarm needs to be checked the system has a delay on the securing process

C4 DAQ

Suite 601 - The card swipe is not unlocking the door

POC AMAG AMAG

BE730 - Node is timed out

AMAG AMAG

Room Number - 2C956 Problem - Card Reader is not working properly

POC

ALT POC - AMAG ENTRY

Badging Office

Printer and Station 3 are down.

AMAG COMPUTER

Location - 3rd and 4th Floor Zone - 1724 & 1722 Problem - Zone Failure

POC -

C3 DAQ ALARM

5D652

Node timed out.

AMAG AMAG

Location - Loading Dock Problem - Door hinge is missing

POC -

This is actually the BMS for the roll-up door. AMAG OTHER

Room Number - 9030 Problem - The door is not securing properly

POC - J AMAG OTHER

Room Number - 1E763 Problem - Tamper Light is inoperable on the panel

POC - AMAG OTHER

Corr 3 E RING (Bottom of stairs)

The swipe at the side door to the trailer is not allowing access.

AMAG ENTRY

JP! - Poll is in failure - Suite 4400 - Zone

Submitted by IEOC C4 DAQ 1401 - Node timed out

POC AMAG AMAG

Room Number - 1D652 Problem - Card Reader is not working properly

POC - AMAG ENTRY

Room Number - 1C547 Problem - Possible Node Timed Out

POC -

AMAG AMAG

Location - MEF Visitor Control Center Problem - Printer is inoperable

POC - AMAG COMPUTER

Room Number - 1B349 IEOC Problem- Amag System is show all rooms offline

POC - AMAG AMAG

Location - RDF Exit Booth Problem - The monitor is out

POC - CCTV

ME873A - This is a conference room and the swipe needs to be reset to have a green light

AMAG ENTRY

MDA (Badging office)

AMAG system is down.

AMAG COMPUTER

1 CCTV monitor is inoperative and the other monitor can only view camera 102. Both monitors are at the security desk in the lobby.

PD 20703 - Maglock is loose on the P1 - Perimeter Door

SUbmitted by AMAG DOOR 5B1064 - 5B1066 - Alarm is malfunctioning - Alarm keeps going off

POC AMAG ALARM

Location - Corridor 8 Problem - Turnstile number 7 needs to be reset

POC - AMAG TURNSTILE

Room Number - 204 Zone - 906 Problem - Alarm keeps going off everytime someone swipes in

POC - C3 DAQ

The CCTV monitor at Post 2-8 (post nearest the flag poles) has a horizontally-split screen and the upper half has no picture. The onsite G510 - PPD Holding Cell camera is frozen, cannot see a picture

Submitted b CCTV

On March 26, 2011 at approximately 1230 hours conducted a check of the emergency call boxes on the Pentagon Reservation.

Air Force Memorial call box #1, Pentagon Athletic Center blue call boxes at stairwells 77 and 78, the upper and lower train platforms, The metro street elevators (car 1 and 2)

The metro train platform elevator, FOB II #'s 3B, 4, 6B, 6D and 6E were all operating properly.

Emergency call boxes on the lower Metro bus platform #'s 1, 2 and 3 and Upper Metro bus platform #'s 4, 5 and 6 can call out but "error tone" is received.

The Air Force Memorial call box #'s 2, 3, 4, 5, and 6 received no dial tone.

The Pentagon Athletic Center red emergency call boxes at stairwells 77 and 78 upper and basement rings, but no one answers.

FOB-2 call box #'s 3A, 6A and 6C inoperable, the slug lane emergency call box located at lane 35 rings, but no answer. AMAG Room Number - 1000 Zone - 580 Problem - Can't access the space or exit unless the door release button is used

POC - C4 DAQ

Room Number - 3B552A Problem - Card Reader needs to be reset

POC - AMAG ENTRY

4C453 - the card swipe is not working on the outside - the light stays red will not go green

Poll 1, 2 and 3 & Rooms

Z - 913 R -12 R - 916 R - 922 R - 204

R - GN35

R - GS22A

R - S11

C4 DAQ

Corr 8

Tenants are not being allowed swipe access on turnstile 2.

AMAG TURNSTILE

Zone 78 - Room ME830 - IAU 1 - in failure -duress in failure

Submitted by C4 DAQ Pars Room

Tenant says that he is unable to seal the room. He thinks it is a miscommunication with the PIR or the BMS. He requested Pedro.

C4 DAQ

2D668

Tenant is not able to swipe in. ACC advised that the node was timed out.

AMAG AMAG

Room number - 4A324 Problem - Card Reader needs to be cleaned

POC - AMAG ENTRY

Room Number - 300 Zone - 262 Problem - Card Reader is inoperable

POC - C3 DAQ

1E1054 - Swipe is not working - Cannot get a history report

AMAG

Room Number - 1E1029 Problem - Alarm keeps going off after the door is closed

Room Number - 5D948 Problem - Card Reader is inoperable

POC - AMAG ENTRY

4C712

Tenant says that there is a constant red light on the reader, located on the back door.

AMAG ENTRY

Room Number - 3B255 Problem - Area is going into alarm

POC - AMAG ALARM

Room Number - 400A Problem - AI Phone are not working properly

POC - AMAG AIPHONE

Location - Mall Entrance Problem - Card Reader on Turnstile number 1 is inoperable

POC - AMAG ENTRY

MEF Turnstilte 1 - is down at the metro

Officer on Duty AMAG TURNSTILE Suite 800 - The maglock is sticking and will not release the door

POC

1E1029 - The door is keeps beeping even when the door is closed

POC AMAG ALARM

During checks of the Apex Center Courtyard tunnels I discovered the Interior Gate located at Apex Corridor 9/10 unsecured with the MAGLOCK on the ground. The Card Reader and the Push-To-Exit button still seemed to be working properly. Re-install the Maglock to the GATE/DOOR located in the Tunnels at Apex Corridor 9/10. AMAG DOOR

During checks of the Apex Center Courtyard tunnels I discovered the Interior Gate/Door located at Apex Corridor 5/6 unsecured and the MAGLOCK NOT WORKING. The Card Reader and the Push-To-Exit button still seemed to be working properly. AMAG DOOR Room Number - 1510 Zone - 979 Problem - Card Reader is inoperable

POC - C3 DAQ

Zone 979 - Room/Suite 1510 - Unknown card alarms on one room sending out aporx.

700 alarms to the IEOC

Submitted by Thompson C4 DAQ Army Poll 5 is down

Location - 11th Floor Problem - Card Reader needs to be reset

POC - C3 DAQ ENTRY

Room Number - 2C749 Problem - Door Release button is not working properly

POC - AMAG ENTRY

Room Number - 2A926 Problem - Node Timed Out

POC - AMAG AMAG

5C682

***NOTE***Tenant would like to schedule this for THURSDAY 3/31/2011 at 10am.

Door is not alarming when shut. Tenat says that building maintenance is doing work on the door to fix the handle and would like a tech to come afterwards.

AMAG DOOR

Room Number - 5D384 Problem - Tenants are locked in the space Maglock will not release

POC - AMAG LOCK

Room Number - 3B710 Problem - Alarm keeps going off after hours and the space is secure

POC - AMAG ALARM

RSAC BE745

Cardswipe has no power.

AMAG ENTRY

RDF to the right of Bay door 12

Door is not securing.

AMAG DOOR

3E267 - Entry door AI phone camera angle does not show visitors to the admn stations inside. Need the camera angle adjusted.

Room

POC's AMAG AIPHONE JP1 Poll 1 is down

Submitted by AMAG POLL 1E1029 - The door is keeps beeping even when the door is closed

POC AMAG ALARM

4E383

Tenant asked that card reader be replaced.

It is 10 years old and they can not read the numbers.

AMAG ENTRY

3D852 - The tenants cannot deactivate the alarm and it keeps going off

Submitted by

AMAG ALARM

HRP - SW5 S25 - Someone pulled the fire alarm in the up position and may need to be reset

AMAG ALARM

MD652

Card swipe is intermittently working.

Sometimes it goes green, but won't release.

AMAG ENTRY

MD638 (leading to RDF)

Door can be pushed open at any time.

AMAG DOOR

10th Floor - the Egress door is not working -the BMS may be out of alignment. Crashbar not releasing mortise lock. Zone 776.

Submitted by C3 DAQ ENTRY Room Number - 5C719 Problem -Top hinge is broken and is not securing the door

POC - AMAG OTHER

Location - MEF Problem - The Card Readers on the turnstiles going in and out of the MEF are not working for new badges

POC AMAG ENTRY

Room Number - 2A926 Problem - The lights on the Card Reader are not working properly

POC - AMAG ENTRY