01 78 23.pdf

SABER Solicitation FA2517-08-R-5002

01 78 23-1 03/24/09

SECTION 01 78 23

OPERATION AND MAINTENANCE DATA

PART 1 GENERAL

1.1 REFERENCES

1.1.1 The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

1.1.1.1 ASTM INTERNATIONAL (ASTM)

a. ASTM E 1971 Stewardship for the Cleaning of Commercial and Institutional

Buildings

1.2 SUBMISSION OF OPERATION AND MAINTENANCE DATA

1.2.1 Submit Operation and Maintenance (O&M) Data specifically applicable to this contract and a complete and concise depiction of the provided equipment, product, or system, stressing and enhancing the importance of system interactions, troubleshooting, and long-term preventative maintenance and operation. The subcontractors shall compile and prepare data and deliver to the

Contractor prior to the training of Government personnel. The Contractor shall compile and prepare aggregate O&M data including clarifying and updating the original sequences of operation to as-built conditions. Organize and present information in sufficient detail to clearly explain O&M requirements at the system, equipment, component, and subassembly level.

Include an index preceding each submittal. Submit in accordance with this section and Section

01 33 00 Submittal Procedures.

1.2.2 Package Quality

1.2.2.1 Documents must be fully legible. Poor quality copies and material with hole punches obliterating the text or drawings will not be accepted.

1.2.3 Package Content

1.2.3.1 Data package content shall be as shown in the paragraph titled "Schedule of Operation and

Maintenance Data Packages." Comply with the data package requirements specified in the individual technical sections, including the content of the packages and addressing each product, component, and system designated for data package submission, except as follows.

Commissioned items without a specified data package requirement in the individual technical sections shall use Data Package 4.

1.2.4 Changes to Submittals

1.2.4.1 Manufacturer-originated changes or revisions to submitted data shall be furnished by the

Contractor if a component of an item is so affected subsequent to acceptance of the O&M Data.

Changes, additions, or revisions required by the Contracting Officer for final acceptance of submitted data, shall be submitted by the Contractor within 30 calendar days of the notification of this change requirement.

../01%2033%2000.doc

01 78 23-2 03/24/09

1.2.5 Review and Approval

1.2.5.1 The Contractor's Commissioning Authority (CA) shall review the commissioned systems and equipment submittals for completeness and applicability. The CA shall verify that the systems and equipment provided meet the requirements of the Contract documents and design intent, particularly as they relate to functionality, energy performance, water performance, maintainability, sustainability, system cost, indoor environmental quality, and local environmental impacts. The CA shall communicate deficiencies to the Contracting Officer.

Upon a successful review of the corrections, the CA shall recommend approval and acceptance of these O&M manuals to the Contracting Officer. This work shall be in addition to the normal review procedures for O&M data.

1.2.6 O&M Database

1.2.6.1 Develop a database from the O&M manuals that contains the information required to start a preventative maintenance program.

1.3 TYPES OF INFORMATION REQUIRED IN O&M DATA PACKAGES

1.3.1 Operating Instructions

1.3.1.1 Include specific instructions, procedures, and illustrations for the following phases of operation for the installed model and features of each system:

a. Safety Precautions

(1) List personnel hazards and equipment or product safety precautions for all operating conditions.

b. Operator Prestart

(1) Include procedures required to install, set up, and prepare each system for use.

c. Startup, Shutdown, and Post-Shutdown Procedures

(1) Provide narrative description for Startup, Shutdown and Post-shutdown operating procedures including the control sequence for each procedure.

d. Normal Operations

(1) Provide narrative description of Normal Operating Procedures. Include Control Diagrams with data to explain operation and control of systems and specific equipment.

e. Emergency Operations

(1) Include Emergency Procedures for equipment malfunctions to permit a short period of continued operation or to shut down the equipment to prevent further damage to systems and equipment. Include Emergency Shutdown Instructions for fire, explosion, spills, or other foreseeable contingencies. Provide guidance and procedures for emergency operation of all utility systems including required valve positions, valve locations and zones or portions of systems controlled.

f. Operator Service Requirements

(1) Include instructions for services to be performed by the operator such as lubrication, adjustment, inspection, and recording gage readings.

01 78 23-3 03/24/09

g. Environmental Conditions

(1) Include a list of Environmental Conditions (temperature, humidity, and other relevant data) that are best suited for the operation of each product, component or system. Describe conditions under which the item equipment should not be allowed to run.

1.3.2 Preventive Maintenance

1.3.2.1 Include the following information for preventive and scheduled maintenance to minimize corrective maintenance and repair for the installed model and features of each system. Include potential environmental and indoor air quality impacts of recommended maintenance procedures and materials.

a. Lubrication Data

(1) Include preventative maintenance lubrication data, in addition to instructions for lubrication provided under paragraph titled "Operator Service Requirements":

(a) A table showing recommended lubricants for specific temperature ranges and applications.

(b) Charts with a schematic diagram of the equipment showing lubrication points, recommended types and grades of lubricants, and capacities.

(c) A Lubrication Schedule showing service interval frequency.

b. Preventive Maintenance Plan and Schedule

(1) Include manufacturer's schedule for routine preventive maintenance, inspections, tests and adjustments required to ensure proper and economical operation and to minimize corrective maintenance. Provide manufacturer's projection of preventive maintenance work-hours on a daily, weekly, monthly, and annual basis including craft requirements by type of craft.

For periodic calibrations, provide manufacturer's specified frequency and procedures for each separate operation.

c. Cleaning Recommendations

(1) Provide environmentally preferable cleaning recommendations in accordance with ASTM

E 1971.

1.3.3 Corrective Maintenance (Repair)

1.3.3.1 Include manufacturer's recommended procedures and instructions for correcting problems and making repairs for the installed model and features of each system. Include potential environmental and indoor air quality impacts of recommended maintenance procedures and materials.

a. Troubleshooting Guides and Diagnostic Techniques

(1) Include step-by-step procedures to promptly isolate the cause of typical malfunctions.

Describe clearly why the checkout is performed and what conditions are to be sought.

Identify tests or inspections and test equipment required to determine whether parts and equipment may be reused or require replacement.

b. Wiring Diagrams and Control Diagrams

(1) Wiring diagrams and control diagrams shall be point-to-point drawings of wiring and control circuits including factory-field interfaces. Provide a complete and accurate

01 78 23-4 03/24/09 depiction of the actual job specific wiring and control work. On diagrams, number electrical and electronic wiring and pneumatic control tubing and the terminals for each type, identically to actual installation configuration and numbering.

c. Maintenance and Repair Procedures

(1) Include instructions and a list of tools required to repair or restore the product or equipment to proper condition or operating standards.

d. Removal and Replacement Instructions

(1) Include step-by-step procedures and a list required tools and supplies for removal, replacement, disassembly, and assembly of components, assemblies, subassemblies, accessories, and attachments. Provide tolerances, dimensions, settings and adjustments required. Instructions shall include a combination of text and illustrations.

e. Spare Parts and Supply Lists

(1) Include lists of spare parts and supplies required for maintenance and repair to ensure continued service or operation without unreasonable delays. Special consideration is required for facilities at remote locations. List spare parts and supplies that have a long lead-time to obtain.

1.3.4 Corrective Maintenance Work-Hours

1.3.4.1 Include manufacturer's projection of corrective maintenance work-hours including requirements by type of craft. Corrective maintenance that requires completion or participation of the equipment manufacturer shall be identified and tabulated separately.

1.3.5 Appendices

1.3.5.1 Provide information required below and information not specified in the preceding paragraphs but pertinent to the maintenance or operation of the product or equipment. Include the following:

a. Product Submittal Data

(1) Provide a copy of all SD-03 Product Data submittals required in the applicable technical sections.

b. Manufacturer's Instructions

(1) Provide a copy of all SD-08 Manufacturer's Instructions submittals required in the applicable technical sections.

c. O&M Submittal Data

(1) Provide a copy of all SD-10 Operation and Maintenance Data submittals required in the applicable technical sections.

d. Parts Identification

(1) Provide identification and coverage for all parts of each component, assembly, subassembly, and accessory of the end items subject to replacement. Include special hardware requirements, such as requirement to use high-strength bolts and nuts. Identify parts by make, model, serial number, and source of supply to allow reordering without further identification. Provide clear and legible illustrations, drawings, and exploded views to enable easy identification of the items. When illustrations omit the part numbers and

01 78 23-5 03/24/09 description, both the illustrations and separate listing shall show the index, reference, or key number that will cross-reference the illustrated part to the listed part. Parts shown in the listings shall be grouped by components, assemblies, and subassemblies in accordance with the manufacturer's standard practice. Parts data may cover more than one model or series of equipment, components, assemblies, subassemblies, attachments, or accessories, such as typically shown in a master parts catalog

e. Warranty Information

(1) List and explain the various warranties and clearly identify the servicing and technical precautions prescribed by the manufacturers or contract documents in order to keep warranties in force. Include warranty information for primary components such as the compressor of air conditioning system.

f. Personnel Training Requirements

(1) Provide information available from the manufacturers that are needed for use in training designated personnel to properly operate and maintain the equipment and systems.

g. Testing Equipment and Special Tool Information

(1) Include information on test equipment required to perform specified tests and on special tools needed for the operation, maintenance, and repair of components.

h. Testing and Performance Data

(1) Include completed pre-functional checklists, functional performance test forms, and monitoring reports. Include recommended schedule for retesting and blank test forms.

i. Contractor Information

(1) Provide a list that includes the name, address, and telephone number of the General

Contractor and each Subcontractor who installed the product or equipment, or system. For each item, also provide the name address and telephone number of the manufacturer's representative and service organization that can provide replacements most convenient to the project site. Provide the name, address, and telephone number of the product, equipment, and system manufacturers.

1.4 TYPES OF INFORMATION REQUIRED IN CONTROLS O&M DATA PACKAGES

1.4.1 Include Data Package 5 and the following for control systems:

1.4.1.1 Narrative description on how to perform and apply all functions, features, modes, and other operations, including unoccupied operation, seasonal changeover, manual operation, and alarms. Include detailed technical manual for programming and customizing control loops and algorithms.

1.4.1.2 Full as-built sequence of operations.

1.4.1.3 Copies of all checkout tests and calibrations performed by the Contractor (not Cx tests).

1.4.1.4 Full points list. A listing of rooms shall be provided with the following information for each room:

a. Floor

b. Room number

01 78 23-6 03/24/09

c. Room name

d. Air handler unit ID

e. Reference drawing number

f. Air terminal unit tag ID

g. Heating and/or cooling valve tag ID

h. Minimum cfm

i. Maximum cfm

1.4.1.5 Full print out of all schedules and set points after testing and acceptance of the system.

1.4.1.6 Full as-built print out of software program.

1.4.1.7 Electronic copy on disk or CD of the entire program for this facility.

1.4.1.8 Marking of all system sensors and thermostats on the as-built floor plan and mechanical drawings with their control system designations.

1.5 SCHEDULE OF OPERATION AND MAINTENANCE DATA PACKAGES

1.5.1 Furnish the O&M data packages specified in individual technical sections. The required information for each O&M data package is as follows:

1.5.1.1 Data Package 1

a. Safety precautions

b. Cleaning recommendations

c. Maintenance and repair procedures

d. Warranty information

e. Contractor information

f. Spare parts and supply list

1.5.1.2 Data Package 2

a. Safety precautions

b. Normal operations

c. Environmental conditions

d. Lubrication data

e. Preventive maintenance plan and schedule

f. Cleaning recommendations

g. Maintenance and repair procedures

h. Removal and replacement instructions

i. Spare parts and supply list

01 78 23-7 03/24/09

j. Parts identification

k. Warranty information

l. Contractor information

1.5.1.3 Data Package 3

a. Safety precautions

b. Operator prestart

c. Startup, shutdown, and post-shutdown procedures

d. Normal operations

e. Emergency operations

f. Environmental conditions

g. Lubrication data

h. Preventive maintenance plan and schedule

i. Cleaning recommendations

j. Troubleshooting guides and diagnostic techniques

k. Wiring diagrams and control diagrams

l. Maintenance and repair procedures

m. Removal and replacement instructions

n. Spare parts and supply list

o. Product submittal data

p. O&M submittal data

q. Parts identification

r. Warranty information

s. Testing equipment and special tool information

t. Testing and performance data

u. Contractor information

1.5.1.4 Data Package 4

a. Safety precautions

b. Operator prestart

c. Startup, shutdown, and post-shutdown procedures

d. Normal operations

e. Emergency operations

f. Operator service requirements

g. Environmental conditions

h. Lubrication data

01 78 23-8 03/24/09

i. Preventive maintenance plan and schedule

j. Cleaning recommendations

k. Troubleshooting guides and diagnostic techniques

l. Wiring diagrams and control diagrams

m. Maintenance and repair procedures

n. Removal and replacement instructions

o. Spare parts and supply list

p. Corrective maintenance man-hours

q. Product submittal data

r. O&M submittal data

s. Parts identification

t. Warranty information

u. Personnel training requirements

v. Testing equipment and special tool information

w. Testing and performance data

x. Contractor information

1.5.1.5 Data Package 5

a. Safety precautions

b. Operator prestart

c. Start-up, shutdown, and post-shutdown procedures

d. Normal operations

e. Environmental conditions

f. Preventive maintenance plan and schedule

g. Troubleshooting guides and diagnostic techniques

h. Wiring and control diagrams

i. Maintenance and repair procedures

j. Removal and replacement instructions

k. Spare parts and supply list

l. Product submittal data

m. Manufacturer's instructions

n. O&M submittal data

o. Parts identification

p. Testing equipment and special tool information

q. Warranty information

01 78 23-9 03/24/09

r. Testing and performance data

s. Contractor information

PART 2 PRODUCTS – Not Used

PART 3 EXECUTION – Not Used

END OF SECTION 01 78 23

01 78 23-10 03/24/09