36E77619B0012-0004003.pdf

September 11, 2019 ADDENDUM NO. 001

A 320 NW 10th Street, Suite A, Oklahoma City, OK 73103 P 405.842.6100 E design@spur-design.com W spur-design.com

PROJECT: Radiology Expansion PROJECT #: 649-613 / SPUR 1395.24

Northern Arizona VA Health Care System

Prescott, AZ

OWNER: Dept of Veterans Affairs

THE FOLLOWING MODIFICATIONS, ADDITIONS, AND DELETIONS ARE HEREBY MADE A PART OF THE CONTRACT DOCUMENTS.

ADDENDUM PROJECT MANUAL ITEMS:

Attached Supplemental Information:

1. Soil Report – add to Project Manual

2. Product Data-Basis of Design 3Form varia ecoresin – add to Project Manual

3. Product Data-Basis of Design Stonhard Stonerez RTZ - add to Project Manual

4. Detail for Knock-out - add to Project Manual

5. Signage Details - add to Project Manual

6. Structural Detail – add to Project Manual

Attached Specifications:

7. Specification Section 04 05 13 Masonry Mortaring – add to Specifications

8. Specification Section 04 05 16 Masonry Grouting - add to Specifications

9. Specification Section 04 20 00 Unit Masonry - add to Specifications

10. Specification Section 04 72 00 Cast Stone Masonry - add to Specifications

11. Specification Section 07 27 26 Fluid Applied Air Barriers, Vapor Permeable - add to Specifications

12. Specification Section 12 32 00 Manufactured Wood Casework - add to Specifications

13. Specification Section 13 49 16 Radio Frequency and Magnetic Sheilding for RFI – replace existing section

13 49 16 with this revised section.

Attached Construction Drawings:

14. 107-SS-001 Structural Details-Replace existing sheet 107-SS-001 with this revised sheet 107-SS-001.

15. 107-SS-100 Foundation Plan-Replace existing sheet 107-SS-100 with this revised sheet 107-SS-100.

16. 107-SS-201 Foundation Details-Replace existing sheet 107-SS-201 with this revised sheet 107-SS-201.

17. 107-AS-411 Interior Elevations II-Replace existing sheet 107-AS-411 with this revised sheet 107-AS-411.

18. 107-AS-701 Finish Floor Plan and Signage-Replace existing sheet 107-AS-701 with this revised sheet 107-

AS-701.

END OF ADDENDUM NO. 001

1FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

FEATURES AND BENEFITS

• Produced on an individual order basis, allowing for creative design and product selection (minimum order quantity – ONE sheet!)

• Heat-formable into virtually any shape or size for eye-catching installations

• SCS-certified recycled content helps achieve LEED® credits for building sustainability

• Very tough, allowing for easy fabrication and maximum installed durability

• Extremely versatile which enables designers to achieve full design potential

• Lightweight, half the density of glass, which makes for easier installation and reduces structural support requirements

• Excellent chemical resistance which reduces potential harm incurred by cleaning agents

• Varia Ecoresin is GREENGUARD Indoor Air Quality Certified

• Varia Ecoresin is Underwriters Laboratories registered

AVAILABLE INTERLAYERS AND COLORS

Varia Ecoresin is available in a variety of standard interlayer and color options. Visit 3-form.com for all available options.

TEXTURES AND FINISHES

Each product in the Varia Ecoresin collection comes standard with both a front and back finish. Additionally, 3form provides the option of substituting between standard finishes. In most cases, you can even pick diff erent front and back finishes.

Finishes include:

• Grain - Refined organic detail in a translucent wood grain finish.The pattern direction runs parallel to the eight foot side of the panel.

• Grid - Fine, horizontal crosshatched lines create a subtle texture.

• Patent - A high gloss finish with highest light transmittance

• Patina - A non-glare finish with smooth appearance

Product Description

3form Varia Ecoresin is a dynamic interlayer system with design possibilities as diverse as your imagination. By al-lowing you to custom-select the color, pattern, texture, interlayer and finish of your material, Varia Ecoresin trans-forms into the perfect medium for your architectural application.

An award-winning 3form product, Varia Ecoresin has the added benefit of being made from a specially-formulated co-polyester resin that combines performance with environmental responsibility. Ecoresin incorporates 40% pre-consumer recycled content without compromising aesthetics or overall physical properties, is compatible with one of the largest post-consumer recycle streams, and is GREENGUARD® Indoor Air Quality Certified.

• Sandstone - A more durable finish with a subtle texture

• Stucco - A durable finish with a pebbled texture

• Supermatte - A frosted matte finish for maximum light diffusion

• Vellum - A random brushed matte finish similar to the 3form renewable matte finish.

• Velvet - Durable blurred finish with a crushed velvet appearance.

The pattern direction runs parallel to the four foot side of the panel.

Additionally 3form low-VOC functional coatings may be applied to the surface of 3form Varia Ecoresin. Finishes include:

• Patina Plus - Non-glare finish with slightly frosted appearance

• SFX Frost - Applied frosted finish with paper-like appearance

• Writeable - Applied finish for markerboard application

PANEL SIZES AND TOLERANCES

Varia Ecoresin panels are offered in 4' x 8' (1.2 m x 2.4 m) and 4' x 10' (1.2 m x 3 m). All dimensions and squareness are subject to a 3/16" (4.7 mm) tolerance. 5' x 10' (1.5 m x 3 m) is also available, though some restrictions apply.

Varia Ecoresin is available in gauges from 1/16 inch to 1 inch.

NOMINAL MINIMUM MAXIMUM

THICKNESS ALLOWANCE ALLOWANCE

GAUGE GAUGE GAUGE

1/8" (3.1 mm) 0.098” 0.138”

3/16" (4.7 mm) 0.155” 0.205”

1/4" (6.3 mm) 0.196” 0.306”

3/8" (9.5 mm)* 0.304” 0.434”

1/2" (12.7 mm) 0.412” 0.562”

3/4" (19.0 mm) 0.618” 0.798”

1.0" (25.4 mm) 0.850” 1.090”

*Add +/- 1/32” (+/-0.8 mm) to the above tolerance for hint textured sheets.

**Add +/- 3/16” (+/-4.7 mm) to the above tolerance for all embossed texture sheets.

x varia ecoresin®

[Tiger Thatch]

2FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

Sheet tolerance readings are based on an average of several mea-surements along both long edges of each panel. These measure-ments are taken 2-3 inches (50-75 mm) from the edges of the panel.

PATTERN SKEW TOLERANCE

Linear patterns in Varia Ecoresin panels have a skew tolerance of 1/4" skew over 48”. Panels containing a pattern (Capiz, Timber, etc.) will not match up from sheet to sheet. If the sheets are intended to match, they should be field cut on-site to a smaller final sheet dimen-sion. HiRes panels will have an alignment tolerance of 1/4” from sheet to sheet.

FLATNESS TOLERANCE

Varia Ecoresin panels shall not have distortion in the form of a wrin-kle, twist or scallop along the perimeter of the sheet. Overall warp extending across the sheet is permitted to a maximum of 9/32" (7.14

mm) for each 48" (1.2 m) or fraction thereof. Panel is to be measured when laying horizontally under its own weight on a flat continuous surface.

Specifications

FLAMMABILITY & SMOKE TEST RESULTS –

BUILDING CODE APPROVALS

Varia Ecoresin has been independently tested and meet the criteria for approved interior finishes and light transmitting resin materials as described in the 2016 International Building Code®.

TEST 3FORM VARIA ECORESIN RESULT

ASTM D 2843 Smoke Density 71.6% PASS Less than 75

ASTM D 635 Flame Spread Self extinguishing PASS CC1

ASTM D 1929 Self-ignition Temperature

716°F PASS Greater than 650°F

UL94 Flame Class - HB PASS

UPITT Mortality Test PASS Not more toxic than wood

NFPA 286

1/4" thickness + below (walls only or ceilings only) 3/8" thickness + below (walls in standoff configuration or ceilings only)

Pass

Pass

Pass

Pass

The NFPA 286 corner burn test is accepted by the 2012 IBC for interior finishes. Passing the NFPA 286 test allows for materials to be utilized where Class A materials are required (IBC 803.1.2).

ASTM E84

Flame Spread, 1/8" thickness Smoke generated

Class A: 0-25 <450

ASTM E84

Flame Spread, 3/16" thickness Smoke generated

Class A: 0-25 <450

ASTM E84

Flame Spread, 1/4" thickness Smoke generated

Class B: 26-75 <450

ASTM E84

Flame Spread, 1/2" thickness Smoke generated

Class B: 26-75 <450

ASTM E84

Flame Spread, 3/4" thickness Smoke generated

Class B: 26-75 <450

ASTM E84

Flame Spread, 1" thickness Smoke generated

Class A: 0-25 <450

Due to their specialty construction, 3from Dichroic, Reflect and 3form Wood have their own unique set of fire performance results.

TEST 3FORM DICHROIC/REFLECT RESULT

ASTM D 2843 Smoke Density 47.5% PASS Less than 75

ASTM D 635 Flame Spread 17.4 mm/min PASS CC2

ASTM D 1929 Self-ignition Temperature

716°F PASS Greater than 650°F

ASTM E84

Flame Spread, 1/4" thickness Smoke generated

Class B: 26-75 <450

TEST 3FORM TIMBER RESULT

ASTM E84-03

Flame Spread, 3/8" thickness Smoke generated

Class B: 26-75 <450

PANEL WEIGHT

THICKNESS (INCHES) WEIGHT FLUX (LB/FT2)

1/16" (1.5 mm) 0.4 lb/ft2 (2.0 kg/m2) 1/8" (3.1 mm) 0.8 lb/ft2 (3.9 kg/m2) 3/16" (4.7 mm) 1.2 lb/ft2 (5.9 kg/m2) 1/4" (6.3 mm) 1.7 lb/ft2 (8.3 kg/m2) 3/8" (9.5 mm) 2.5 lb/ft2 (12.2 kg/m2) 1/2" (12.7 mm) 3.3 lb/ft2 (16.1 kg/m2) 3/4" (19.0 mm) 5.0 lb/ft2 (24.4 kg/m2) 1.0" (25.4 mm) 6.6 lb/ft2 (32.2 kg/m2)

EXPANSION/CONTRACTION ALLOWANCES

Like all resin products, 3form Varia Ecoresin will expand and contract nominally with fluctuations in temperature. The following formula provides allowances that should be made in framed or fitted applica-tions:

• Longest length of panel (inches) x temperature change of the sheet (°F) x 0.00004 = Amount of Linear Expansion/ Contraction (inches)

EXAMPLE:

• 48" x 96" panel experiencing 50°F temperature change will expand/ contract: 96 inches x 50 degrees x 0.00004 in/in ºF = 0.192 inches Installers should take extra precautions if installation is occurring before the HVAC systems are operational. Allowances should also be made in the following situations:

• Fastening points

• Channel depths in frames

• Holes for standoffs and other hardware

• Meeting points for multiple sheets of 3form Varia Ecoresin

USAGE LIMITATIONS

DO NOT use cyanoacrylate or solvent type thread locking materials with Varia Ecoresin. To more permanently secure hardware, use the recommended products from the 3form adhesives matrix.”

REFLECT

When using Varia Reflect in pressure fitting applications, such as stand-off supports, use a pressure distribution plate or neoprene gasket to prevent localized panel separations.

Varia Reflect cannot be heat formed.

DICHROIC

3form Dichroic has an inherent linerarity running parallel to the panel length. The 3form Dichoic interlayer is very delicate, it is not recom-mended for use in exterior applications.

DO NOT cut Dichroic with a jigsaw, scroll saw, or waterjet.

When using Dichroic in pressure fitting applications, such as stand-off supports, use a pressure distribution plate or neoprene gasket to prevent localized panel separations.

3FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

NATURALS

Varia Ecoresin Panels utilizing natural or organic materials (ie. leaves, branches or twigs) may change in appearance over time. Natural materials are also subject to inherent inconsistency in color, texture and shape. Small areas of delamination are also to be expected, especially near saw cut edges.

METALLICS

Varia Ecoresin panels utilizing metallic interlayers (ie. Hollywood, Electra, Itemba, Mirror print) may change in appearance over time due to antiquing of the metallic materials.

TIMBER

Because 3form Timber is produced from engineered wood products, it is not recommended for use in high moisture or exterior applica-tions. Wood products are very responsive to environmental condi-tions (moisture, humidity, temperature changes) and therefore is re-stricted to interior applications. Wood pieces in Timber may contain knots, imperfections, dark spots, stains and color variation.

After trimming, the following treatments improve the edge aesthet-ics.

Natural: Sand edges with 220 grit sandpaper and carefully wipe the edges with Weld-On 3 (or MEK) making sure not to get any of the chemical on the face or back of the sheet.

Mocha: Sand edges with 220 grit sandpaper and carefully wipe the edges with Minwax Special Walnut 224 stain.

OTHER

Birch will sometimes bleed and cause small amounts of yellowing while being manufactured. In addition, due to the manufacturing press process, birch bulbs may be dispersed within the sheet, some of which will be trapped in clear areas for the Birch Grove pattern.

Structured Bamboo is a one-sided product.

FABRICATION

Do not drill or fasten the Varia Ecoresin within 2x thickness of panel edge. See the 3form Varia Fabrication Manual for more detailed guidelines and instructions on cutting, drilling, routing, etc. of Varia Ecoresin panels.

EDGE SEALING

Certain Varia Ecoresin designed layers (organics, papers and fabrics in particular) can have a tendency to wick moisture over time if the edges become wet and are not adequately sealed. These Varia Ecoresin products should not be exposed to water or wet conditions without first applying an approved edge sealing treatment. Varia Ecoresin produced using C3 or HighRes do not require edge sealing.

These are good options to use as an alternative to Woven Colors and Organics. Edge sealing is required on all exposed edges (including any holes that are created to allow for stand-off fastening). There are some designed Varia Ecoresin Woven Colors that do not exhibit wicking behavior and therefore do not need to be edge sealed. If you have additional questions or concerns regarding edge sealing of 3form products please contact 3form.

DEFLECTION

3form Varia Ecoresin will exhibit different amounts of deflection given a variety of factors: fastening techniques, loads, gauges and panel dimensions to list a few. 3form can assist you with general deflection guidelines for your application. You may also consult the Varia Deflection Charts technical white paper. If your application has specific engineering requirements, please contact 3form for ad-ditional direction.

HEAT FORMING/COLD BENDING

Varia Ecoresin can be cold bent for simple bends and curved areas.

As a general rule, a minimum radius of 100 times thickness is ac-ceptable for Varia Ecoresin (will depend on interlayer material). A minimum radius of 250 times thickness should be used for Dichroic.

A minimum radius of 200 times thickness should be used for Timber (with the bending axis parallel to the wood slats).

Heat formed Dichroic panels will have a finished size 6” less on each dimension than the standard size sold.

STANDARD SIZE SIZE AFTER FORMING

48” x 96” 42” x 90” 48” x 120” 42” x 116”

PANEL THICKNESS

MINIMUM COLD BEND RADII

VARIA ECORESIN DICHROIC/REFLECT WOOD

1/16" (1.5 mm) 7" (178 mm) - -

1/8" (3.1 mm) 12" (305 mm) 32" (813 mm) 24" (610 mm)

3/16" (4.7 mm) 19" (483 mm) 47" (1194 mm) 37" (950 mm)

1/4" (6.3 mm) 25" (635 mm) 63" (1600 mm) 50" (1270 mm)

3/8" (9.5 mm) 37" (940 mm) 94" (2388 mm) 75" (1905 mm)

1/2" (12.7 mm) 50" (1270 mm) 125" (3175 mm) 100" (2540 mm)

3/4" (19.0 mm) 75" (1905 mm) 188" (4775 mm) 150" (3810 mm)

1" (25.4 mm) 100" (2540 mm) 250" (6350 mm) 200" (5080 mm)

Because of its low thermoforming temperature, Varia Ecoresin is easy to line bend or drape form. For specific details on line bending and heatforming please consult the 3form Varia Ecoresin Fabrication Manual.

The special construction of 3form Dichroic and Wood introduces challenges in terms of heat forming. Because both are rigid interlay-ers, complex curvature is not possible. Simple curves and bends may be accomplished.Timber can only be heat-formed in simple curves, perpendicular to the direction of the wood. Minimum heat forming radius for Timber is 48”.

For highly complex shapes and curves, consult with or employ the services of the experts in 3form Fabrication.

EDGE FINISHING

Edges of 3form Varia Ecoresin panels are able to be machined or routed into a variety of different forms. In addition to a straight edge, edges may accept beveling, rounding, etc. Additional finishing, such as sanding or polishing, can also be provided to some edges.

4FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

REFINISHING

It is possible for Varia Ecoresin to become damaged by scratching.

Patent is the only Varia Ecoresin finish that may be repaired, and requires use of a flame polishing technique.

Light scratches and scuffs on the sandstone surface finish can be repaired with a plastic polish. The majority of 3form products have a surface finish that would be ruined by buffing.

SOUND TRANSMISSION CLASS (STC) VALUES FOR VARIA ECORESIN

Measurement protocol: ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements

THICKNESS STC VALUES

1/8" (3.1 mm) 25

3/16" (4.7 mm) 29

1/4" (6.3 mm) 31

3/8" (9.5 mm) 34

1/2" (12.7 mm) 34

1" (25.4 mm) 39

THERMAL INSULATION VALUES FOR VARIA ECORESIN

Insulative values are a function of both the convective properties (U-values and shading coefficients) and the conductive properties (thermal conductivity).

Measurement protocol: ASTM E 903 - Standard Test Method for Solar Absorbance, Reflectance and Transmittance of Materials Using Integrating Spheres. ASTM E 891-87 - Tables for Terrestrial Direct Normal Solar Spectral Irradiance Tables for Air Mass. ASTM E 408-71

- Standard Test Method for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques.

VARIA ECORESIN CLEAR

THICKNESS

WINTER U-VALUE

(BTU/HR-FT2-°F)

SUMMER U-VALUE

(BTU/HR-FT2-°F)

1/4" (6.3 mm) 0.97 0.93

3/8" (9.5 mm) 0.90 0.87

1/2" (12.7 mm) 0.83 0.80

Chemical Resistance of 3form Varia Ecoresin to Select Compounds

365 DAY FULL IMMERSION TESTING @ 73ºF (23ºC)

Polymer materials are affected by chemicals in different ways.

Changes in performance or appearance can be attributed to fab-rication methods, exposure conditions, concentration of chemical substances or exposure duration. Such factors can even influence the final effect of substances that 3form Varia Ecoresin is considered "Resistant" to under test conditions. Further details are explained below:

FABRICATION

Stresses generated from sanding, grinding, drilling, polishing, ma-chining, sawing and/or forming (hot or cold).

EXPOSURE

Exposure duration, stresses imparted during the application life-cycle due to loads, temperature changes, heat, environments, etc.

APPLICATION OF CHEMICALS

Application from contact, rubbing, wiping, spraying, soaking, etc.

Also having an affect is the relative concentration of the chemical in question.

Selected Mechanical and Physical Properties for 3form Varia Ecoresin Values reported for Varia Ecoresin with no decorative inserts. Deco-rative inserts may increase or may decrease specific test results.

Should your application require specific test values, consult the 3form Product Technology Department.

TYPICAL VALUE

0.118" (3 MM) 0.236" (6 MM)

PROPERTY* ASTM METHOD SI U.S. SI U.S.

GENERAL

Density D 1505 1,270 kg/m3 79 lb/ft3 1,270 kg/m3 79 lb/ft3

Water Absorption

D 570 23° C (73° F), 24h immersion

0.2% 0.2% 0.1% 0.1%

MECHANICAL

Tensile Stress @ Yield

D 638 53 MPa 7,700 psi 53 MPa 7,700 psi

Tensile Stress @ Break

D 638 26 MPa 3,800 psi 26 MPa 3,800 psi

Elongation @ Yield D 638 4.8% 4.8% 5.0% 5.0%

Elongation @ Break D 638 50% 50% 40% 40%

Tensile Modulus D 638 2,200 MPa 320,000 psi

Flexural Modulus D 790 2,100 MPa 310,000 psi

2,000 MPa 290,000 psi

Flexural Strength D 790 77 MPa 11,200 psi 83 MPa 12,000 psi

Shear Strength D 732 62 MPa 9,000 psi 62 MPa 9,000 psi

Shear Modulus — 793 MPa 115,000 psi — —

Rockwell Hardness D 785 115 115 117 117

Safety Glazing ANSI 97.1 PASS PASS

Izod Impact Strength, Notched

D 256 @ 73°F D 256 @ 32°F D 256 @–22°F

88 J/m 66 J/m 39 J/m

1.7 ft·lbf/in.

1.2 ft·lbf/in.

0.7 ft·lbf/in.

62 J/m

1.2 ft·lbf/in.

Impact Strength, Unnotched

D 4812 @ 73°F D 4812 @ 32°F D 4812 @ –22°F

NB**

NBB

NBB

NB**

NBB

NBB

NB**

NB**

Impact Resistance— Puncture, Energy @ Max. Load

D 3763 @ 73°F D 3763 @ 32°F D 3763 @ 14°F D 3763 @ –4°F D 3763 @ –22°F

33 J 40 J 42 J 43 J 47 J

24 ft·lbf 30 ft·lbf 31 ft·lbf 32 ft·lbf 34 ft·lbf

71 J 93 J 96 J >100 J >100 J

53 ft·lbf 69 ft·lbf 71 ft·lbf >74 ft·lbf >74 ft·lbf

THERMAL

Cont. Max Use Temperature -Varia

– 65ºC 150ºF 65ºC 150ºF

Cont. Max Use Tem-perature - Dichroic/ Reflect

– 60ºC 140ºF 60ºC 140ºF

Heat Deflection Temp

D 648 @ 264psi 70ºC 157ºF 73ºC 164ºF

Vicat Softening Temperature

D 1525 @ 1 kg 83ºC 181ºF — —

Forming Tempera-ture

— 138-160ºC 280-320ºF — —

Thermal Conduc-tivity

ASTM D 5930 0.205 W/

m·K

0.118 Btu/

hr·ft2·ºF

0.205 W/

m·K

0.118 Btu/

hr·ft2·ºF

Coefficient of Ther-mal Expansion

ASTM D 696 7x10-5 mm/ mm/ºC

4x10-5 in/ in/ºF

7x10-5 mm/ mm/ºC

4x10-5 in/ in/ºF

*Unless noted otherwise, all tests are run @ 73°F (23°C) and 50% relative humidity, using specimens machined from extruded sheeting with a thickness as indicated.

**Nonbreak as defined in ASTM D 4812 using specimens having a thickness as indicated.

Properties reported here are typical of average lots. 3form makes no representation that the material in any particular shipment will conform exactly to the values given.

5FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

The following data is based on complete immersion of Varia Ecoresin in the chemical or reagent shown. Samples remained immersed and were stored at 73ºF (23ºC) for a period of one year. Following the test period the samples were removed from immersion and inspected.

The following table provides indicative performance of the chemical resistance characteristics of Ecoresin. The following codes are used to describe the chemical resistance characteristics:

R = RESISTANT

3form Varia Ecoresin is able to withstand the identified compound for long exposure periods up to 120ºF (7 days, full immersion)

LR = LIMITED RESISTANCE

3form Varia Ecoresin is only resistant when in contact with this compound for short periods at room temperature. It is advised that further determination of the effect of the substance be further tested in your particular application.

NR = NOT RESISTANT

3form Varia Ecoresin is not resistant to the compound. The material will swell, craze, haze, dissolve or experience some physical change when exposed to this substance.

REAGENT RESULT REAGENT RESULT

Acetic Acid, 5% R Acetic Acid, conc. NR

Acetone NR Ammonium Hydroxide, conc. NR

Antifreeze, Automotive Ethylene Glycol Type

R Benzene NR

Brake Fluid, DOT3 R Brake Fluid LR

Carbon Tetrachloride NR Chromic Acid, 40% R

Citric Acid, 10% R Cottonseed Oil R

Deionized Water R Detergent, Alconox (0.25%) R

Di (2-Ethylhexyl) Phthalate R Dibutyl Sebacate R

Diesel Fuel LR Dimethyl Formamide NR

Ethanol, 50% R Ethanol, 100% R

Ethyl Acetate NR Ethylene Dichloride NR

Gasohol, 10% Ethanol LR Gasohol, 10% Methanol LR

Gasoline, Base for Gasohol LR Gasoline, Premium Unleaded LR

Gasoline, Regular R Gasoline, Regular Unleaded LR

Grease, Automotive R Hand Cleaner, Waterless Jergens

SBS30

R

Hexane R Hydrochloric Acid, conc. NR

Hydrochloric Acid, 10% R Hydrogen Peroxide, 3% R

Hydrogen Peroxide, 28% R Isooctane R

Kerosene R Lacquer Thinner LR

Methyl Alcohol LR Mineral Oil R

Motor Oil R Nitric Acid, conc. NR

Nitric Acid, 10% R Nitric Acid, 40% LR

Oleic Acid, 83% R Olive Oil R

OxiCide, product use dilution R Penetrating Oil, Liquid Wrench #1 NR

Phenol, 5% NR Silicone Spray Lubricant NR

Soap Solution, 1% R Sodium Carbonate, 2% R

Sodium Carbonate, 20% R Sodium Chloride, 10% R

Sodium Hydroxide, 1% R Sodium Hydroxide, 10% R

Sodium Hypochlorite, 3.5% R Sulfuric Acid, conc. NR

Sulfuric Acid, 3% R Sulfuric Acid, 30% R

Tapping Oil R Toluene NR

Transformer Oil LR Transmission Fluid, Auto R

Turpentine LR

Cleaning Instructions 3form Varia Ecoresin, like all thermoplastic resin materials, should be cleaned periodically. A regular, seasonal cleaning program will dramatically help prevent noticeable weathering and dirt build-up.

3form recommends the use of the following common cleaning prod-ucts: Windex, Formula 409, Simple Green, Fantastik, Virex, 10:1 Water/ Bleach Solution.

Rinse the sheets with lukewarm water. (Be careful not to expose edges of organic or fabric interlayers to water) Remove dust and dirt from Varia Ecoresin with a soft cloth or sponge and a solution of mild soap and/or liquid detergent in water. A 50:50 solution of isopropyl alcohol and water also works well. Rinse thoroughly with lukewarm water.

Always use a soft, damp cloth to blot dry. Rubbing with a dry cloth can scratch the material and create a static charge. Never use scrapers or squeegees on Varia Ecoresin. Also avoid scouring com-pounds, gasoline, benzene, acetone, carbon tetrachloride, certain deicing fluids, lacquer thinner or other strong solvents.

Writeable: Erasable markers contain an ink that dries instantly and should be easily erased. After a period of use, a film or haze could de-velop on the surface, which is the result of the ink residue that might not be completely removed when the board is erased.

By using a spray on type of glass cleaner, the board may be given a thorough cleaning. Simply spray the surface and briskly rub with a clean microfiber cloth. Rinse with clear water. Avoid using caustic or abrasive types of cleaners.

DO:

• Keep edges dry and free of liquids

• Apply cleaning solution or water to a clean cloth and wipe resin clean

DO NOT:

• Use a squeegee.

• Use strong solvents, highly alkaline or abrasive cleaning agents.

• Clean in hot sun or at elevated temperatures.

• Rub with a dry cloth.

• Do not completely saturate panel with cleaning solution or water

• Expose organic or fabric interlayers to water or cleaning solution

PRESSURE WASHING

Pressure washing can also be an effective way to remove miscella-neous debris from surfaces of 3form Varia Ecoresin installations that are in exterior or hard-to-reach places.

Pre-soak panels with a light water spray to loosen and remove inci-dental surface debris.

It is recommended that the water pressure for cleaning Varia Ecoresin panels be 1,500 psi or less. 3form Varia Ecoresin is a tough material but can be damaged if high pressure is concentrated in a single position too long. Use a gradual sweeping motion over the ap-plication. Never concentrate water spray in a single position. Pressure nozzle should never be positioned closer than 8 inches (203 mm) from the panel surface.

Test a portion of the sheet first before spraying. If test piece shows any sign of material fatigue, abrasion or delamination – discontinue

6FEBRUARY 15 2019 | MATSPEC - VARIA | REV 034

pressure washing and proceed with manual cleaning instructions as described above.

Coated or painted parts are not suitable for pressure washing as finish may be stripped off. Pressure washing is also not suitable for Varia Ecoresin panels that have been edge sealed or seamed. If using detergent, use mild detergents only. Rinse sheet with light water spray after washing.

DO NOT:

• Concentrate spray in single position.

• Use more than 1,500 psi pressure.

• Position pressure nozzle closer than 8" (203 mm) from panel.

• Proceed with pressure washing if test piece shows detrimental effects to panel.

• Pressure wash Varia Ecoresin panels that have been painted or coated to maintain coating integrity.

• Pressure wash Varia Ecoresin panels with sealed edges to ensure edge seals remain in tact.

If debris or dirt is not removed by pressure washing attempt to clean with manual procedures described in preceding section.

WRITEABLE FINISH

Use Low Odor Dry Erase markers from a reputable brand. It is best to store markers horizontally so that the felt tips do not dry out. Avoid using markers with dried out tips.

Use a dry, soft cloth for cleaning. Press firmly when erasing using a circular motion.

Please remember to use a clean cloth/eraser when erasing. A dirty cloth/eraser will leave ink residue on the writing surface. Microfiber cloths are preferred over felt erasers because they can be machine laundered making them easier to keep clean.

For periodic cleaning, rinse the entire writing surface with soapy water and then dry with a soft cloth.

To remove any permanent marker ink, use a 50:50 solvent solution of isopropyl alcohol and water. You can also trace over any areas of permanent marker ink with a dry erase marker and erase using a dry, soft cloth.

DO NOT:

• Use sharp objects such as pens, pointers, metal magnets, rings/ jewelry, knives, scrapers on your writing surface.

• Drag magnets across your writing surface.

• Use felt erasers, scouring pads or other harsh cleaners on your writing surface.

• Use any abrasive material or fingernails to remove tape or stickers.

• Expose edges of panel to moisture or cleaning solutions.

For more information, please visit 3-form.com or call 877-649-2670.

1�����

2�����

1�����

3�����

1�����

1�����

01234567892:

;<=>?@AB=

CBDD

EFGH@ID>

JI;KB;

CKD?<J

L<MHLEHN

JLHHO ABDD<F

LI<; DKJICBLH

DI;?I@AH JI;MID

EFGH@D?BLC

DBF<?GNH D?B;>H;=H DCBOH@P;@C<LLBLD J><FFHN JIEI;I@EFGH

?BL?<FFI >HI?>HL

EGL;<D>HN@ELB;QH

?HLLI

?LBR<JD

�,��S�'�(

B

A.1

A

A.2UIP.

M

MRI ACCS.

146D

2' -5

/2

'-2

/2

17'-2"

2'-0"

8'-6"W X 9'-0"H MRI

WALL KNOCKOUT

MRI SCAN

ROOM

146C

B.1

8' -6

STEEL COLUMN,

RE: STRUCTURAL

STUCCO TO MATCH

ADJACENT EXISTING FINISH

6" METAL STUD FRAMING

W/ BATT INSULATION

2 LAYER 5/8" GYP. BD.

W/ RF SHIELDING

WEATHER BARRIER ON

EXTERIOR SHEATHING

RF / MAGNETIC SHIELDING WALL

ASSEMBLY PER SHIELDING VENDOR

1" AIR SPACE

2 LAYER 5/8" TYPE 'X' GYP. BD. ON

1 5/8" METAL STUD FRAMING

1/4" SEALANT & BACKER ROD

FIRE-RATED

SEALANT

K N

O C

K -O

U T

P A

N E

L

K N

O C

K -O

U T

P A

N E

L

1 1/2" = 1'-0"

PLAN DETAIL - 1 HR COLUMN WRAP W/ RF SHIELDING

Detail provided in response to Pre-Bid RFI Q70.

VA/Pres/Dwg/Man2

FACILITY

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

NORTHERN ARIZONA VA HEALTH CARE SYSTEM

INTERIOR SIGNAGE MANUAL

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-01

EXPLODED VIEW - FRAME W/O FACE PANELS

NOT TO SCALE

SIDE VIEW - MOUNTING

NOT TO SCALE

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-02

GRAPHIC TEXTURES COLOR PALETTES

1040 Creative CG 1C C:0 | M:0 | Y:0 | K:4 Secondary Color

Satin Anodized Aluminum Frame

Wilsonart - Magnolia Background

Primary Color

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-03

NOTES:

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

2 Ply Construction w/ 1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digital Printed Background Adhered to Sintra

Magnetically Mounted 3Ply Non-Glare Acrylic Construction w/ Subsurface VOC Free Digitally Printed Background & Acetate Insert.

Beveled FrameExisting

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digitally Printed Copy, Graphic & Background where Applicable

1”=3”

ADA ROOM

NUMBER/IDENTIFICATION

SIGN SYSTEM STANDARDS INTERIOR FAMILY OF COMPONENTS - Existing Beveled Frame

FINISHES:

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C1 -

Creative 541c

COLOR C4 -

BRIGHT WHITE

Creative White

COLOR C3-

Black CSS Black

2J-100 A

B

D

C1

R1

TYPE: D1A/W

9”

3”

Conference Room

2J-100

9”

3”

6”

9”

A

B

C

R1

TYPE: D1A/F/W

C1

D

COLOR R1 -

BRIGHT WHITE

Rowmark White

COLOR R2 -

BLACK

Rowmark Black

TYPE: SA/W

ROOM NUMBER / IDENTIFICATION

D

E

A R2

C2

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-04

NOTES:

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background, Graphic & Surface Voc Free Digitally Printed Copy where applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy where Applicable & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

M.

F1192

Staff Workroom

8-½”

2-¾”

5-½”

8-½”

A

B

C

E

G

F

F12043-¼”

8-½”

A

B

F

G

1”=3”

ADA ROOM

NUMBER/IDENTIFICATION

SIGN SYSTEM STANDARDS

R1

F1

C1

R1

F2

TYPE: D1A/Wc

TYPE: D1A/F/Wc

F1226

8-½”

2-¾”

5-½” 10-¾”

Vacant2-¼”

A

B

C

E

G

F

H

TYPE: D1A/F/O/Wc

ROOM NUMBER / IDENTIFICATION

R1

In Use

Conference Room

C1 F2

C1

FINISHES:

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR R1 -

BRIGHT WHITE

Rowmark White

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C4 -

BRIGHT WHITE

Creative White

COLOR C3-

Black CSS Black

COLOR C5 - RED

CSS Fire Red

C4 C5

COLOR C1 -

Creative 541c

CREATIVE Continuum Brand Name or Equal

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-05

NOTES:

MEN

F1209

FINISHES:

F1

8-½"

WOMEN

,Restroom

8-½”

8-½”

F

D

G

F12072-¾” A

B

C

11-½”

F1

R1

F2

R2

TYPE: D1A/SA/Wc

1” = 3”

Room Identification

C1

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR R1 -

BRIGHT WHITE

Rowmark White

COLOR R2 -

BLACK

Rowmark Black

F2

F2

R2

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C3-

Black CSS Black

C1

F2

F1

F1

F2

SIGN SYSTEM STANDARDS

COLOR C1 -

Creative 541c

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background, Graphic & Surface Voc Free Digitally Printed Copy where applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy where Applicable & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

M.

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-06

SCALE: 1” = 4”

NOTES:

Directional / Pocket Sign

CHAPERONE & UNATTENDED

CHILDREN POLICY

Every patient (and healthcare provider) has a right to have a chaperone present during a medical examination. If you so desire, please notify the clinic staff.

IAW TAMC regulation 101, unattended children 10 years of age and younger are not authorized in the department of radiology. An adult, other than the patient must accompany these children.

8-½”

11”

TYPE: P/Wc

INSERT HOLDER

F

G

E

F2

Keep Locked at All Times

5-½”

8-½”

F

G

D

TYPE: E/Wc

PERMANENT MESSAGE SIGN

8-½”

Lab TYPE: P5/Wc

DIRECTIONAL SIGN

F

G

D

8-½”

FINISHES:

8-½”

11”

TYPE: E1/P/Wc

TERTIARY DIRECTIONAL

F

G

E

F2

2-3/4”

11”

17”

TYPE: E/P/Wc

ELEVATOR DIRECTORY

F

G

E

3” Directory

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

F1

F2

F1

B C1

F1

F2

F1

F2

F1

B C1

COLOR C4 -

BRIGHT WHITE

Creative White

COLOR C3-

Black CSS Black

C4 C4

C

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background, Graphic & Surface Voc Free Digitally Printed Copy where applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy where Applicable & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

M.

COLOR C1 -

SIGN SYSTEM STANDARDS CREATIVE Continuum Brand Name or Equal

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-07

11”

3”

33”

17”

• Buildings 20-24

• Patriot Café (20)

• Pharmacy (21)

• Welcome Desk

BLDG

3”

TYPE: Cc-2/P-2/Cc/Wc

DOUBLE DIRECTIONAL SIGN

FLOOR 2

Buildings 20-24 •

Patriot Café (20) •

Pharmacy (21) •

Welcome Desk •

3”

11”

11”

3”

18”

17”

TYPE: Cc/P/Cc/Wc

SMALL DIRECTIONAL SIGN

• Buildings 20-24

• Patriot Café (20)

• Pharmacy (21)

• Welcome Desk

BLDG

3” FLOOR 2

1” = 5”

NOTES:

Large Directional Pocket Sign

B

E

F

G

F2

F1

FINISHES:

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C4 -

BRIGHT WHITE

Creative White

COLOR C3-

Black CSS Black

C1 C4

B C1 C4

PATTERN P1 -

P1

B

E

F

G

F2

F1

C1 C4

B C1 C4 P1

B

E F1

C1 C4

SIGN SYSTEM STANDARDS CREATIVE Continuum Brand Name or Equal

COLOR C1 -

Creative 541c

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background, Graphic & Surface Voc Free Digitally Printed Copy where applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy where Applicable & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-08

NOTES:

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background

Steel Cable Hanging System

A.

B.

Cable

Bracket

Header

2-Ply Non-Glare Acrylic

Ceiling Mount

B B

B

C2 C2

C2

FINISHES:

Pharmacy

ENT/Plastics Comp & Pen

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C3-

Black CSS Black

C1

C1 C1

COLOR C1 -

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-09

NOTES: 1” = 3”

Overhead Room Identification

C2

FINISHES:

C2

12”

Waiting Room

FINISH F2 -

SATIN ALUMINUM

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C3-

Black CSS Black

C1 C1

F2F2

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

A.

B.

B B

AA

COLOR C1 -

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-010

SCALE: 1” = 6”

Architectural Letters - Finish & Size Varies

Compensation & Pension 4” x ¼” Cut-Out Aluminum Letters

& 2” x ¼” Cut-Out Aluminum Diamonds Satin Aluminum Finish

Font: Futura Md Bt

Compensation & PensionCompensation & Pension

6” x ¼” Cut-Out Aluminum Letters & 3” x ¼” Cut-Out Aluminum Diamonds

Satin Aluminum Finish Font: Futura Md Bt

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-011

NOTES:

TYPE: A4/A2/Wc

MEDIUM DIRECTORY MAP SIGN

FINISHES:

22-½”

5”

28”

Directory

34 1/4”

5”

11”

17"

28”

22 1/2”

TYPE: A4/P-6/Wc

INSERT HOLDER / INFORMATION SIGN

11”

L

F

G

YOU

ARE

HERE F2

B C1

First Floor

SA

MP

LE

MA

P

Floor 1

E

B

F

G

F1

F2

C

Ambulatory Surgery

Dental Clinic

GI Procedure Lab

Hematology/Oncology

Emergency Department

Department Floor

Education Services

Clinics 3A-D

Human Resources

Inpatient Units 5A, 5B

Inpatient Units 4A, 4B

Neurology

Prosthetics

Lab/Specimen Collection

Release of Information............................G

Pathology

Ambulatory Surgery

Dental Clinic

GI Procedure Lab

Hematology/Oncology

Emergency Department

Department Floor

Education Services

Clinics 3A-D

Human Resources

Inpatient Units 5A, 5B

Inpatient Units 4A, 4B

Neurology

Prosthetics

Lab/Specimen Collection

Release of Information............................G

Pathology

Sam pl e

Li st in gs

Sam pl e

Li st in gs

Sam pl e

Li st in gs

Sam pl e

Li st in gs

FINISH F2 -

SATIN ALUMINUM

FINISH F1

LAMINATE

Wilsonart Magnolia (Magnolia - Leno Weave 5012)

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C4 -

BRIGHT WHITE

Creative White

COLOR C3-

Black CSS Black

PATTERN P1 -

SIGN SYSTEM STANDARDS

COLOR C1 -

Creative 541c

C4 P1 C1 C4 P1

1” = 6”

Information Signs

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

1/8” P95 Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background, Graphic & Surface Voc Free Digitally Printed Copy where applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy where Applicable & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-012

1”=10”

¾” Aluminum Round Stand-Off

½” Clear Acrylic Panel with Subsurface VOC Free Digitally Printed Graphics

1/16” Non-Glare Removable Lens w/ Subsurface VOC Free Digital Printed Copy/Graphic & Removable Background Panel w/ Laminate adhered to ACM (where applicable)

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

A.

B.

C.

D.

Component Based System w/ Sprint Clip Loading for Interchangeable Variable Depth Media

5” x ¼” Cut-Out Satin Aluminum Architectural Letters.

Typeface: Futura Md BT

1/8” Brushed Aluminum ACM w/ Surface VOC FREE Digitally Printed Graphics

3/8” Frosted Acrylic w/ Subsurface VOC Free Digitally Printed Background

E.

F.

G.

H.

24” 20”

6”

18”

9”

8”

18”

19”

4”

5”

30”

37”

24” 47”

G

C

D

E

Main Entry Policy Feature Wall

VA F

or m

AKA

Pol ic ie s & D ire ct iv es

M an da to ry P ol ic y Sig n

Pat ie nt

R ig ht

R es po ns ib ilit ie s

3-¼”x 20” x ¼” Cut-Out Satin Aluminum LogotypeI.

B

A

I

H

NOTE: Please confirm Image Panel final dimension.

F

FINISH F2 -

SATIN ALUMINUM

COLOR C2 -

COOL GREY

Creative CG 1C (1040)

COLOR C3-

Black CSS Black

NOTES: FINISHES:

F2

F2

F2

COLOR C1 -

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-013

Caution Radiation

Bio-Hazard Eye Wash

Authorized Personnel Only

TYPE: Q/Wc

REGULATORY SIGN

TYPE: S/Wc

LIFE SAFETY SIGN

8-½”

8-½”

TYPE: R/Wc

REGULATORY SIGN

TYPE: R/Wc

LIFE SAFETY SIGN

F

L

G

NOTES: FINISHES:

F

L

G

F

L

G

F

L

G

F2F2

F2 F2

8-½”

8-½”

8-½”

8-½”

8-½”

8-½”

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

Removable Background Panel with Laminate adhered to ACM, & VOC FREE Digitally Printed where Applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy, & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

M.

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

FINISH F2 -

SATIN ALUMINUM

COLOR C3-

Black CSS Black

COLOR C4 -

BRIGHT WHITE

Creative White

1”=4”

Regulatory Signs

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-014

FIRE

DOOR

KEEP CLOSED

at all times

8-½”

COLOR C5 - RED

CSS Fire Red

TYPE: V4/Wc

REGULATORY SIGN

TYPE: V3/Wc

ELEVATOR WARNING SIGN

F

L

G

NOTES: FINISHES:

F

L

G

9”

9”

TYPE: G D/F

PROJECTING/LIFE SAFETY SIGN

K

F

9”

9”

TYPE: G D/F

PROJECTING/LIFE SAFETY SIGN

K

F

COLOR C4 -

BRIGHT WHITE

Creative White

F2 F2 F2

F2

1/16" Non-Glare Removable Lens & Removable Background Panel w/ Surface VOC Free Digital Printed Copy, Graphic & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel w/ Surface VOC Free Digital Printed Background

K.

L.

F.

G.

H.

I.

J.

A.

B.

C.

D.

E.

ADA Tactile Numbers & Grade II Braille

Removable Background Panel with Laminate adhered to ACM, & VOC FREE Digitally Printed where Applicable

Removable Aluminum Accent

Non-Glare Removable Lense w/ Subsurface VOC Free Digital Printed Graphic/Copy, & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

Non-Glare Removable Lens, Acetate Insert & Removable Background Panel w/ Wilsonart Laminate adhered to ACM

75% Recycled Aluminum Anodized Holder;

Mechanically Fastens to the Wall (Limits Future Wall Damage)

M.

8-½”

8-½”

8-½”

Component Based System w/ Spring Clip Loading for Interchangeable Variable Depth Media

Slider Unit - Digitally Printed Background

2 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Copy, Graphics & Background

1/16" Non-Glare Removable Lens with Subsurface VOC Free Digital Printed Copy & Removable Background Panel

3 Ply Non-Glare Acrylic Construction Subsurface VOC Free Digital Printed Background & Copy

FINISH F2 -

SATIN ALUMINUM

COLOR C3 -

Black CSS Black

1”=4”

Regulatory Signs

SHEET

DESIGNER

SHEET

DRAWN BY

SHEETSHEETSHEET

Bob Stump VA Medical Center Northern Arizona VA Health Care System

SHEETSHEET

REVISIONS

SHEETSHEET

PROJECT

SHEET

Interior Signage Manual

SHEETSHEET

SIGN TYPE

SCALE:

DW-015

Martinsburg, WV Tranquility House - Bldg 513

First Floor

LEGEND

Restrooms

Exits Elevator

Stairs

17”

Fire Extinguisher

9”

9”

TYPE: G D/F

PROJECTING/LIFE SAFETY SIGN

K

F

NOTES: FINISHES:

TYPE: V/Wc

EVACUATION PLAN

What To Do In Case Of Fire:

R A C E

RESCUE

ALARM

CONFINE

EXTINGUISH

Immediate life saving and CLOSE THAT DOOR!

Pull the alarm and call XXXX giving exact location and information.

Close doors and windows to prevent fire/smoke spread.

Know…