UFGS_06_61_16_Solid_Surfacing_Fabrications_-_UFGS_06_61_16.pdf

SECTION 06 61 16 Page 1

SECTION 06 61 16

SOLID SURFACING FABRICATIONS

08/10

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced . The publications are referred to within the text by the basic designation only.

ASTM INTERNATIONAL (ASTM)

ASTM 02583 (2013a) Indentation Hardness of Rigid

Plastics by Means of a Barcol Impressor

ASTM 05116 (2010) Standard Guide for Small-Scale

Environmental Chamber Determinations of Organic Emissions from Indoor Materials/Products

ASTM 0570 (1998; E 2010; R 2010) Standard Test

Method for Water Absorption of Plastics

ASTM 0638 (2014) Standard Test Method for Tensile

Properties of Plastics

ASTM 0696 (2016) Standard Test Method for

Coefficient of Linear Thermal Expansion of Plastics Between -30 degrees C and 30 degrees C With a Vitreous Silica Dilatometer

ASTM E84 (2016) Standard Test Method for Surface

Burning Characteristics of Building Materials

ASTM G21 (2015) Determining Resistance of Synthetic

Polymeric Materials to Fungi

CSA GROUP (CSA)

CSA B45.5-ll/IAPMO Zl24 (2011; Update l 2012) Plastic Plumbing

Fixtures - First Edition

NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)

ANSI/NEMA LO 3 (2005) Standard for High-Pressure Decorative Laminates

NSF INTERNATIONAL (NSF)

NSF/ANSI 51 (2012) Food Equipment Materials

SCIENTIFIC CERTIFICATION SYSTEMS (SCS)

SECTION 06 61 16 Page 2 scs SCS Global Services (SCS)Indoor Advantage

TILE COUNCIL OF NORTH AMERICA (TCNA)

TCNA Hdbk (2013) Handbook for Ceramic, Glass, and

Stone Tile Installation

U .S . GREEN BUILDING COUNCIL (USGBC)

LEED BD+C (2009; R 2010) Leadership in Energy and Environmental Design(tm) Building Design and Construction (LEED-NC)

UL ENVIRONMENT (ULE)

ULE Greenguard UL Greenguard Certification Program

1.2 SYSTEM DESCRIPTION

a. Work under this section includes latrine vanity tops with integral lavatory bowls as shown on the drawings and as described in this specification. Do not change source of supply for materials after work has started, if the appearance of finished work would be affected .

b . In most instances, installation of solid polymer fabricated components and assemblies will require strong, correctly located structural support provided by other trades. To provide a stable, sound, secure installation, close coordination is required between the solid polymer fabricator/installer and other trades to ensure that necessary structural wall support, cabinet counter top structural support, proper clearances, and other supporting components are provided for the installation of wall pane ls, countertops, shelving, and all other solid polymer fabrications to the degree and extent recommended by the solid polymer manufacturer.

c. Appropriate staging areas for solid polymer fabrications. Allow variation in component size and location of openings of plus or minus 3 mm 1/8 inch.

l .3 SUBMITTALS

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for information only. When used, a designation following the "G" designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00, SUBM ITTAL PROCEDURES:

SD-02 Shop Drawings

Detail Drawings; G Installation; G, SD-03 Product Data

Solid Polymer Material Qualifications Fabrications Certification

SECTION 06 61 16 Page 3

SD-04 Samples

Material; G Counter and Vanity Tops; G

SD-06 Test Reports

Solid Polymer Material

SD-07 Certificates

Fabrications Qualifications

SD-10 Operation and Maintenance Data

Clean-up

1.5 QUALITY ASSURANCE

1.5.l Qualifications

To ensure warranty coverage, solid polymer fabricators shall be certified to fabricate by the solid polymer material manufacturer being utilized.

Mark all fabrications with the fabricator's certification label affixed in an inconspicuous location. Fabricators shall have a minimum of 5 years of experience working with solid polymer materials. Submit solid polymer manufacturer's certification attesting to fabricator qualification approval.

1.6 DELIVERY, STORAGE, AND HANDLING

Do not deliver materials to project site until areas are ready for installation. Deliver components and materials to the site undamaged, in containers clearly marked and labeled with manufacturer's name. Materials shall be stored indoors and adequate precautions taken to prevent damage to finished surfaces. Provide protective coverings to prevent physical damage or staining following installation, for duration of project.

1.7 WARRANTY

Provide manufacturer's warranty of ten years against defects in materials, excluding damages caused by physical or chemical abuse or excessive heat.

Warranty shall provide for material and labor for replacement or repair of defective material for a period of ten years after component installation.

PART 2 PRODUCTS

2 .1 MATERIAL

Provide solid polymer material that is a homogeneous filled solid polymer;

not coated, laminated or of a composite construction; meeting CSA B45.5-ll/IAPMO Zl24 requirements. Material shall have minimum physical and performance properties specified. Superficial damage to a depth of

0.25 mm 0.01 inch shall be repairable by sanding or polishing. Material thickness shall be as indicated on the drawings. In no case shall material be less than 6 mm 1/4 inch in thickness. Submit a minimum 4 by 4 inch sample of each color and pattern for approval. Samples shall indicate full range of color and pattern variation. Approved samples shall be retained as a standard for this work. Submit test report results from an independent testing laboratory attesting that the submitted solid

SECTION 06 61 16 Page 4 polymer material meets or exceeds each of the specified performance requirements .

2 .1. 1 Cast, 100 Percent Acrylic Polymer Solid Surfacing Material

Cast, 100 percent acrylic solid polymer material shall be composed of acrylic polymer, mineral fillers, and pigments and shall meet the following minimum performance requirements :

PROPERTY REQUIREMENT

(min. or max. )

TEST PROCEDURE

Tensile Strength 291 kg/cm2 4000 psi (max. ) ASTM D638

Hardness 55-Barcol Impressor (min.) ASTM D2583

Thermal Expansion .0000386cm/cm/deg c .000023 in/in/F (max. )

ASTM D696

Boiling Water Surface Resistance

No Change ANSI/NEMA LD 3-3.05

High Temperature Resistance

No Change ANSI/NEMA LD 3-3.06

Impact Resistance (Ball drop) ANSI/NEMA LD 3-303

6.4 mm 1/4 inch sheet 910 mm, 227 g 36 inches, 1/2 lb ball, no failure

12.7 mm 1/2 inch sheet 3550 mm, 227 g 140 inches, 1/2 lb

19 mm 3/4 inch sheet 5070 mm, 227 g 200 inches, 1/2 lb

Mold & Mildew Growth No growth ASTM G21

Bacteria Growth No growth ASTM G21

Liquid Absorption (Weight in 24 hrs.)

0.1 percent max. ASTM D570

Flammability ASTM E84

Flame Spread 25 max.

Smoke Developed 30 max.

TEST PROCEDURE

Sanitation "Food Contact" approval NSF/ANSI 51

2 .1.2 Acrylic-modified Polymer Solid Surfacing Material

Cast, solid polymer material shall be composed of a formulation containing acrylic and polyester polymers, mineral fillers, and pigments. Acrylic

SECTION 06 61 16 Page 5 polymer content shall be not less than 5 percent and not more than 10 percent in order to meet the following minimum performance requirements:

TEST PROCEDURE

Tensile Strength 288 kg/cm2 4100 psi (max. ) ASTM D638

Hardness 50-Barcol Impressor (min.) ASTM D2583

Thermal Expansion .0000386cm/cm/deg c .000023 in/in/F (max. )

ASTM D696

Boiling Water Surface Resistance

No Change ANSI/NEMA LD 3-3.05

High Temperature Resistance

No Change ANSI/NEMA LD 3-3.06

Impact Resistance (Ball drop) ANSI/NEMA LD 3-303

6.4 mm 1/4 inch sheet 910 mm, 227 g 36 inches, 1/2 lb

12.7 mm 1/2 inch sheet 3550 mm, 227 g 140 inches, 1/2 lb

19 mm 3/4 inch sheet 5070 mm, 227 g 200 inches, 1/2 lb

Mold & Mildew Growth No growth ASTM G21

Bacteria Growth No growth ASTM G21

Liquid Absorption (Weight in 24 hrs.)

0.6 percent max. ASTM D570

Flammability ASTM E84

Flame Spread 25 max.

Smoke Developed 100 max.

TEST PROCEDURE

Sanitation "Food Contact" approval NSF/ANSI 51

SECTION 06 61 16 Page 6

2 .1.3 Material Patterns and Colors

Patterns and colors for all solid polymer components and fabrications shall be multi-color pattern vanity countertops with solid color lavatory bowls. Pattern and color shall occur, and shall be consistent in appearance, throughout the entire depth (thickness) of the solid polymer material.

2 .1.4 Surface Finish

Exposed finished surfaces and edges shall receive a uniform appearance.

Exposed surface finish shall be matte; gloss rating of 5-20.

2 .2 ACCESSORY PRODUCTS

Accessory products, as specified below, shall be manufactured by the solid polymer manufacturer or shall be products approved by the solid polymer manufacturer for use with the solid polymer materials being specified.

2 .2.1 Seam Adhesive

Seam adhesive shall be a two-part adhesive kit to create permanent, inconspicuous, non-porous, hard seams and joints by chemical bond between solid polymer materials and components to create a monolithic appearance of the fabrication . Adhesive shall be approved by the solid polymer manufacturer. Adhesive shall be color-matched to the surfaces being bonded where solid-colored, solid polymer materials are being bonded together.

The seam adhesive shall be clear or color matched where particulate patterned, solid polymer materials are being bonded together.

2 .2.2 Panel Adhesive

Panel adhesive shall be neoprene based panel adhesive meeting TCNA Hdbk, Underwriter's Laboratories (UL) listed. Use this adhesive to bond solid polymer components to adjacent and underlying substrates.

2 .2.3 Silicone Sealant

Sealant shall be a mildew-resistant, FDA and OSHA Nationally Recognized Testing Laboratory (NRTL) listed silicone sealant in a clear formulation.

The silicone sealant shall be approved for use by the solid polymer manufacturer. Use sealant to seal all expansion joints between solid polymer components and all joints between solid polymer components and other adjacent surfaces such as walls, floors, ceiling, and plumbing fixtures.

2 .2.4 Conductive Tape

Conductive tape shall be manufacturer's standard foil tape, 4 mils thick, applied around the edges of cut outs containing hot or cold appliances.

2 .2.5 Omitted

2 .2.6 Heat Reflective Tape

Heat reflective tape as recommended by the solid polymer manufacturer for use with cutouts for heat sources.

SECTION 06 61 16 Page 7

2 .2.7 Mounting Hardware

Provide mounting hardware, including sink/bowl clips, inserts and fasteners for attachment of under mount sinks and lavatories.

2 .3 FABRICATIONS

Components shall be factory or shop fabricated to sizes and shapes indicated, to the greatest extent practical, in accordance with approved

Shop Drawings and manufacturer's requirements. Provide factory cutouts for sinks, lavatories, and plumbing fixtures where indicated on the drawings.

Contours and radii shall be routed to template, with edges smooth.

Defective and inaccurate work will be rejected. Submit product data indicating product description, fabrication information, and compliance with specified performance requirements for solid polymer, joint adhesive, sealants, and heat reflective tape . Both the manufacturer of materials and the fabricator shall submit a detailed description of operations and processes in place that support efficient use of natural resources, energy efficiency, emissions of ozone depleting chemicals, management of water and operational waste, indoor environmental quality, and other production techniques supporting sustainable design and products.

2 .3.l Joints and Seams

Form joints and seams between solid polymer components using manufacturer's approved seam adhesive. Joints shall be inconspicuous in appearance and without voids to create a monolithic appearance.

2 .3.2 Edge Finishing

Rout and finish component edges to a smooth, uniform appearance and finish. Edge shapes and treatments, including any inserts, shall be as detailed on the drawings. Rout all cutouts, then sand all edges smooth.

Repair or reject defective or inaccurate work.

2 .3.3 Counter and Vanity Top Splashes

Fabricate backsplashes and end splashes from 1/2 inch thick solid surfacing material to be 4 inches high.

Backsplashes and end splashes shall be provided at locations indicated on the drawings. Backsplashes shall be shop fabricated and be loose, to be field attached.

2 .3.3.l Omitted

2 .3.3.2 End Splashes

End splashes shall be provided loose for installation at the jobsite after horizontal surfaces to which they are to be attached have been installed.

SECTION 06 61 16 Page 8

2 .3.4 Omitted

2 .3.5 Omitted

2 .3.6 Counter and Vanity Tops

Fabricate all solid surfacing, solid polymer counter top and vanity top components from 1/2 inch thick material. Edge details, dimensions, locations, and quantities shall be as indicated on the Drawings.

Counter tops shall be complete with 4 inch high loose, 90 degree transition where indicated on the drawings. Attach 2 inch wide reinforcing strip of polymer material under each horizontal counter top seam. Submit a minimum 1 foot wide by 6 inch deep, full size sample for each type of counter top shown on the project drawings. The sample shall include the edge profile and backsplash as detailed on the project drawings. Solid polymer material shall be of a pattern and color as indicated on the drawings. Sample shall include at least one seam. Approved sample shall be retained as standard for this work.

2 .3.6.1 Vanity Tops With Bowls

a. One-piece vanity top and bowl fabrications shall be a standard pre-fabricated product provided by the solid polymer manufacturer .

Each unit shall include a vanity top with integral backsplash and sink bowl. Countertop to be multicolor pattern with a solid color lavatory bowl. Lavatory bowl to be fitted with a over flow drain assembly.

2 .3.7 Omitted

2 .3.8 Solid Polymer Vanity Bowls

Solid polymer vanity bowls shall be a standard product of the solid polymer manufacturer, designed specifically to be installed in solid polymer vanity tops. Bowls shall be of the same polymer composition as the adjoining counter top. Bowl design shall support a seam adhesive under-mount installation method. Bowl dimensions shall be 1 9 i n c h e s w i d e b y 1 7 i n c h e s f r o n t t o b a c k . B o w l d e p t n o t t o e x c e e d 6 i n c h e s .

PART 3 EXECUTION

3.1 INSTALLATION

3.1.1 Components

Install all components and fabricated units plumb, level, and rigid.

Make field joints between solid polymer components using solid polymer manufacturer's approved seam adhesives, to provide a monolithic appearance with joints inconspicuous in the finished work . Attach metal or vitreous china sinks and lavatory bowls to counter tops using solid polymer manufacturer's recommended clear silicone sealant and mounting hardware . Solid polymer sinks and bowls shall be installed using a color-matched seam adhesive Plumbing connections to sinks and lavatories shall be made in accordance with Section 22 00 00 PLUMBING, GENERAL PURPOSE. ].

3.1.1.1 Loose Counter Top Splashes

Mount loose splashes in the locations noted on the drawings. Loose

SECTION 06 61 16 Page 9 splashes shall be adhered to the counter top with a color matched silicone sealant when the solid polymer components are solid colors.

Use a clear silicone sealant to provide adhesion of particulate patterned solid polymer splashes to counter tops.

3.1.1.2 Wall Panels & Panel Systems

Installation of wall panels and system components to substrates shall include the use of a neoprene-based panel adhesive. Use seam adhesive to adhere all solid polymer components to each other with the exception of expansion joints and inside corners. All inside corners and expansion joints between solid polymer components shall be joined with silicone sealant. All joints between solid polymer components and non-solid polymer surfaces shall be sealed with a clear silicone sealant.

3.1.2 Silicone Sealant

Use a clear, silicone sealant or caulk to seal all expansion joints between solid polymer components and all joints between solid polymer components and other adjacent surfaces such as walls, floors, ceiling, and plumbing fixtures. Sealant bead shall be smooth and uniform in appearance and shall be the minimum size necessary to bridge any gaps between the solid surfacing material and the adjacent surface. Bead shall be continuous and run the entire length of the joint being sealed.

3.1.3 Plumbing

Make plumbing connections to sinks and lavatories in accordance with Section (22 00 00 PLUMB ING, GENERAL PURPOSE]

3.2 CLEAN-UP

Components shall be cleaned after installation and covered to protect against damage during completion of the remaining project items.

Components damaged after installation by other trades will be repaired or replaced at the General Contractor's cost. Component supplier will provide a repair/replace cost estimate to the General Contractor who shall approve estimate before repairs are made. Submit a minimum of six copies of maintenance data indicating manufacturer's care, repair and cleaning instructions. Maintenance video shall be provided, if available. Maintenance kit for matte finishes shall be submitted.