EQUIPMENT CUT SHEETS

AND

PRODUCT DATA SHEETS

FOR

COUNTY OF NAPA

NAPA, CALIFORNIA

BELLA HOUSE KITCHEN AND BATHROOM REHAB

PROJECT

PW 26-25

08/11/2026

100% CONSTRUCTION DRAWINGS

Prepared By:

COAR Design Group

200 ‘E’ Street Santa Rosa, CA 95404

JUAN S. ARIAS COUNTY ENGINEER R.C.E. #C63365

NAPA COUNTY 9/1/2026

BELLA DRIVE REHAB HOUSE Table of Contents-CUT SHEETS Napa, California TOC-1

NAPA COUNTY

BELLA HOUSE KITCHEN AND BATHROOM REHAB PROJECT

EQUIPMENT CUT SHEETS AND PRODUCT DATA SHEETS

TABLE OF CONTENTS SPECIFICATION

SECTION

DIVISION 06 – WOOD, PLASTICS, COMPOSITES

06-01 CASEWORK COLOR (PL-1) 06 40 23

06-02 COUNTERTOP (SSU-1) 06 40 23

DIVISION 09 – FINISHES

09-01 FLOORING (LVT-1) 09 65 19

09-02 4-INCH PVC FLOOR BASE 09 65 13

09-03 SOLID SURFACE WET WALL 09 71 61

09-04 PAINT COLORS (PT-1) 09 91 23

DIVISION 10 – SPECIALTIES

10-01 GRAB BARS 10 28 00

10-02 ROBE HOOK 10 28 00

10-03 TOILET PAPER DISPENSER 10 28 00

10-04 TOWEL BAR 10 28 00

10-05 1/2 INCH CORK BOARD 10 95 00

DIVISION 11 – EQUIPMENT

11-01 MICROWAVE RANGE HOOD 10 95 00

DIVISION 22 – PLUMBING (See specification division 22 otherwise)

22-01 TOILET 10 95 00

22-02 BATH SHOWER TRIM KIT 10 95 00

22-03 SHOWER TRIM KIT 10 95 00

22-04 BATH TUB 10 95 00

22-06 BATHROOM SINK 10 95 00

22-07 BATHROOM FAUCET 10 95 00

22-08 KITCHEN SINK 10 95 00

22-09 KITCHEN FAUCET 10 95 00

DIVISION 23 – HVAC (See specification division 23 otherwise)

23-01 EXHAUST FAN 10 95 00

DIVISION 26 – ELECTRICAL (See specification division 26 otherwise)

26-01 24” WALL LIGHT 10 95 00

26-02 36” WALL LIGHT 10 95 00

26-03 RESTROOM CEILING LIGHT 10 95 00

END OF SECTION

S E

L E

C T

IO

N

S F

R O

M W

IL

S

O N

A R

T

H P

L

Wilsonart Woodgrains™

A N T I Q U E B O U R B O N P I N E 8215K-12

ANTIQUE MARULA

PINE

8216K-28

ITALIAN SILVER ASH

8217K-16

KINGSWOOD WALNUT

8218-38

IVORY BIRCH

8219-38

FRENCH PEAR

8220-38

SAP WALNUT

8221-38

RANDOLPH FOREST

8225K-79

WASHED CHAR

8222K-16

FRISTON ASH

8229K-79

VALLEY FORGE ELM

8231K-79

CONTINENTAL

WALNUT

8232K-05

BELAIR

8234K-05

DAINTREE

8235K-05

MONTEVERDI

8236K-05

FAIRCHILD

8238K-05

CENIZO CHERRY

8239-38

NORWEGIAN ASH

8241-38

JUBILEE OAK

8242-38

MAPLE PB NATURAL

8269K-05

LIMBER MAPLE

10734-60

FONTHILL PEAR

10745-60

KENSINGTON MAPLE

10776-60

NEWLANDS

8268K-17

N E W

ANDERSON CHERRY

8266K-17

N E W

N E W

MAPLE PB CASHMERE

8285K-05

N E W

MAPLE PB NUTMEG

8271K-05

MAPLE PB CHESTNUT

8272K-05

N E W N E W

CHERRY PB NATURAL

8273K-05

N E W

CHERRY PB TOASTED

8274K-05

N E W

CHERRY PB SIENNA

8275K-05

CHERRY PB AUBURN

8276K-05

N E W N E W

WALNUT PB NATURAL

8277K-05

N E W

WHITE OAK PB

WHEATON

8282K-05

WALNUT PB MELLOW

8278K-05

N E W

WALNUT PB COGNAC

8279K-05

N E W

WALNUT PB EMBER

8286K-05

N E W

WHITE OAK PB

NATURAL

8281K-05

N E W N E W

WHITE OAK PB HONEY

8283K-05

N E W

WHITE OAK PB SPICE

8284K-05

N E W

SHAPING

Design Wilsonart Solid Surface is shaping the next generation of engineered surface innovation. Explore an exceptional range of designs that seamlessly blend form and function, delivering unmatched durability and powerful versatility to everyday spaces. How will your project take shape?

O P U L E N T L U X E 9 9 1 8 S S

K E E P E X P L O R I N G A T W I L S O N A R T. C O M / S O L I D - S U R F A C E - N E W - A R R I V A L S

W I L S O N A R T ® S O L I D S U R F A C E https://www.wilsonart.com/solid-surface-new-arrivals

PA R T I C U L A T E S

M O R N I N G I C E 9 2 0 4 C E

Y U K O N R I V E R S T O N E 9 1 9 6 R S

F R O S T Y W H I T E M I R A G E 1 5 7 3 M G

C H A I C R E A M M I R A G E 9 1 1 1 M G

A V A L A N C H E M E L A N G E 9 1 7 5 M L

M Y S T I Q U E 9 2 0 0 C S

P E A R L M I R A G E 9 1 9 9 M G

B L U E S T O N E 9 0 7 4 E A

A N G O R A S A N D S 9 2 5 5 S S

N E W

C H I L L E D E A R T H 9 2 2 8 S S

P O W D E R W H I T E 9 2 3 0 S S

M I L K G L A S S S P E C T R A 9 0 7 7 S T

C O C O N U T O I L 9 1 0 0 G S

W H I T E S T O N E 9 2 0 8 C S

W H I T E W A T E R 9 1 9 8 E A

S H A P I N G D E S I G N

Achieve the distinguished look of extra-wide wood flooring with Moxy XL Coffee Rigid Core Click 9x72 Luxury Vinyl Tile. Inspired by Mingo Oak, its high-definition textured print gives it a realistic wood look, while its extra-large, 9-by-72-inch format makes spaces appear more expansive. Get a good look at a great price with this durable, affordable, easy-to-install LVT.

+5

MOXY XL COFFEE BEIGE RIGID

CORE CLICK 9X72 LUXURY VINYL

PLANK FLOORING

COLORS

Ash Gray Black Chestnut Coffee

LUXURY VINYL PLANK

Coffee https://www.tilebar.com/ https://www.tilebar.com/product/moxy-ash-9x72-rigid-core-click-luxury-vinyl-tile.html https://www.tilebar.com/product/moxy-night-9x72-rigid-core-click-luxury-vinyl-tile.html https://www.tilebar.com/product/moxy-chestnut-9x72-rigid-core-click-luxury-vinyl-tile.html https://www.tilebar.com/product/moxy-coffee-9x72-rigid-core-click-luxury-vinyl-tile.html

FI

N

IS

H

IN

G

B O

R D

ER

S

Millwork Wall Base® System

2 3

System profiles

With the most comprehensive collection of finishing borders in the industry, Johnsonite covers all the details that make a space complete. Choose from a variety of wall base profiles from modern to traditional, along with chair rail, corner guard, quarter rounds, and shoe moulding.

WALL BASE

Ambassador U.S. Patent No. D500,149 Attaché Delineate Diplomat Equinox Exhibit

4" MW-XX-K 6" MW-XX-E 4.25" MW-XX-T 4.5" MW-XX-A 4.5" MW-XX-R 4.25" MW-XX-FS (shown above)

6" MW-XX-FS6

8" MW-XX-FS8

Inflection U.S. Patent No. D499,193 Ledge Mandalay U.S. Patent No. D493,895 Monarch Monument Oblique

5.25" MW-XX-G 6" MW-XX-X62 2.5" MW-XX-H25

3" MW-XX-H3

4.5" MW-XX-H (shown above)

6" MW-XX-H6

6" MW-XX-M 2.5" MW-XX-S25

4" MW-XX-S4 (shown above)

3" MW-XX-N

Outline U.S. Patent No. D484,254 Recessed Reveal U.S. Patent No. D484,253; D510,145 Silhouette Stance

3.5" MW-XX-D 6" MW-XX-X63 4.25" MW-XX-F (shown above)

6" MW-XX-F6

8" MW-XX-F8

4" MW-XX-J 4.5" MW-XX-X60 (shown above)

6" MW-XX-X61

ACCESSORIES

Rampart (chair rail) Corner Guard Shoe Moulding Quarter Round Quarter Round

4" CHR-XX-C VBG-XX-C 1.5" SHU-XX-A 0.5" QTR-XX-A 0.75" QTR-XX-D

NEW

NEW

NEW NEW

Color palette availability

Johnsonite Millwork® is available in all solid colors plus 00 unfinished.

Available in Masquerade palette

MM

M

M

M M M

M

All Johnsonite Millwork profiles are available in standard 8' lengths.

Rampart® (chair rail)

CHR-XX-C

.375"

4"

.25"

6"

Attaché

MW-XX-E

4.5"

.375"

Diplomat®

MW-XX-A

4"

.375"

Ambassador

MW-XX-K

4.25"

.4"

Delineate

MW-XX-T

5.25"

.375"

Inflection

MW-XX-G

4.5"

.375"

Mandalay

MW-XX-H

4.5"

.375"

Equinox

MW-XX-R

4"

.5"

Silhouette®

MW-XX-J

3.5"

.313"

Outline®

MW-XX-D

6"

.19"

Monarch

MW-XX-M

4.25"

.25"

Reveal®

MW-XX-F

3"

.375"

Oblique®

MW-XX-N

4"

.25"

Monument

MW-XX-S4

6"

Recessed

MW-XX-X63

NEW

.35"

4.5"

.35"

Stance

MW-XX-X60

NEW

.35"

6"

Ledge

MW-XX-X62

NEW

4.25"

.25"

Exhibit

MW-XX-FS

NEW

Shoe Moulding

SHU-XX-A

1.5"

.25"

Corner Guard

VBG-XX-C

1.25"

1.25"

.25"

Quarter Round

0.5" QTR-XX-A

0.75" QTR-XX-D

.75"

.5"

.5"

.75"

10 11

Since the early 1960s, the Johnsonite name has been synonymous in the flooring industry with lasting quality, creative flexibility, and unwavering integrity.

With the category's broadest selection of patterns, textures, colors, and profiles—plus the ability to match any tailored palette with quick lead times and low minimums—we'll help you turn what used to be basic rubber tile and finishing accessories into fully coordinated design statements.

We come to work every day to help you win, crafting solutions you can rely on. That's why Made Right Means Johnsonite.

ColorMatch® palette We’ll perfectly match 32 leading colors across Johnsonite’s rubber and vinyl product categories without dye lots

Design flexibility Industry’s broadest selection of colors, patterns, textures and profiles

Healthy materials Free of ortho-phthalates, PFAS and antimicrobials

Made in USA Designed and manufactured in USA;

Buy American Act Compliant

Tailored by Tarkett Precisely match any color with quick lead times and low minimum order quantities

Discover Johnsonite

Meet Tony, the production manager who helps ensure that all Johnsonite products are made right, including the expanded Millwork collection now available in four new profiles and more than 100 stylish colors. If you don’t see the color you need, Tony and his team will create it for you with quick lead times and low minimum order quantities.

ColorMatch®

Perfectly matched flooring and accessories, made easy. This designer palette of leading colors is coordinated across multiple product categories with no dye lots…ever! Our rigorous manufacturing and quality standards enable you to confidently mix and match a color across all Johnsonite rubber and vinyl products, including flooring, finishing borders, and finishing accessories. We guarantee these colors will match year after year, product after product.

08 Icicle W * 24 Grey Haze WG * 55 Silver Grey WG * 32 Pebble WG * 29 Moon Rock WG *

01 Snow White W * 22 Pearl CB * 31 Zephyr CB * 80 Fawn CB * TA8 Welsh Castle CB *

11 Canvas WB * 09 Clay WB * 49 Beige WB * 45 Sandalwood WB * 76 Cinnamon

283 Toast 47 Brown TB1 Peppercorn 167 Fudge 40 Black B *

21 Platinum CG * 38 Pewter CG * 28 Medium Grey CG * 71 Storm Cloud CG * TA6 Bedrock CG *

48 Grey WG * 20 Charcoal WG * TA4 Gateway WG * 63 Burnt Umber B * 44 Dark Brown B *

* See the Color Foundations key on page 8.

86 Hunter Green 18 Navy Blue krt Rectangle krt Arrow

AVONITE™ WET WALL™

Acrylic Solid Surface

Connecting ideas with solutions� aristechsurfaces.com trinseo.com https://www.aristechsurfaces.com https://www.trinseo.com

The need for a clean environment does not mean having to compromise on design

Hygiene Counts

Wellness, Hospitality, Healthcare, Education, Military and more — There is no material that allows for greater cleanliness. AVONITE™ WET WALL™ 100% Acrylic Solid Surface 6 mm sheets do not absorb bacteria, prevent mold and mildew, can be cleaned using common household products, are seamlessly assembled, and the material malleability makes it possible to design curved, rather than angular, corners, for more efficient cleaning.

Impervious

AVONITE™ WET WALL™ 6 mm sheets have been designed to resist a long list of chemical products, including chloric acid. This material for architectural designs and utilitarian surfaces is exceptionally weatherable, strong, non-porous, scratch and stain resistant.

Easy Install

AVONITE™ WET WALL™ 100% Acrylic Solid Surface 6 mm sheets come in various standard and custom sizes to meet the marketplace needs. Standard width options include 36 in., 48 in., and 60 in. wide in a 96 in.

length (914 mm, 1219 mm, 1524 mm, and 2438 mm).

Singular solid surface panels create incredible time savings and cost efficiencies. Fundamentals of installation include plumb walls, measuring twice, cut, shim and attach to backboard with silicone and hot melt (see our AVONITE™ Fabrication Guide for details).

Aesthetic You Need

AVONITE™ WET WALL™ 6 mm sheets are available in our most sought-after colors as well as custom colors (minimums required).

AVONITE™ WET WALL™ 6 mm made-to-order and additional colors or sizes are available with minimum order quantities. Contact your representative for details.

White 8016

Haze 8514

Super White 8026

Mist 8512

Ivory 8106

Oxbow 8510

Bone 8010

Kokoura 9117

Dove Grey 8231

Polaris 8256

Galactic Ice 7790

Sandstorm 9036

Snowfall 8090

Standard Colors

Made-to-Order Colors

#37334F

RGB: 55, 51, 79

CMYK: 81, 80, 43, 38

PPG1169-7

White Text

P1

#595378

RGB: 89, 83, 120

CMYK: 72, 71, 31, 13

PPG1169-6

White Text

P2

#8B8BA5

RGB: 139, 139, 165

CMYK: 49, 43, 22, 1

PPG1169-5

Black Text

P3

#C4C4D6

RGB: 196, 196, 214

CMYK: 22, 19, 7, 0

PPG1169-4

Black Text

P4

#E0DFEA

RGB: 224, 223, 234

CMYK: 11, 9, 2, 0

PPG1169-3

Black Text

P5

#3E5634

RGB: 62, 86, 52

CMYK: 72, 44, 86, 39

PPG1130-7

White Text

G1

#617C4F

RGB: 97, 124, 79

CMYK: 64, 34, 80, 16

PPG1120-7

White Text

G2

#9DB37E

RGB: 157, 179, 126

CMYK: 44, 16, 66, 0

PPG1120-6

Black Text

G3

#CBD7A7

RGB: 203, 215, 167

CMYK: 22, 6, 41, 0

PPG1120-4

Black Text

G4

#E3E8D6

RGB: 227, 232, 214

CMYK: 10, 4, 17, 0

PPG1120-2

Black Text

G5

#304F56

RGB: 48, 79, 86

CMYK: 82, 56, 53, 33

PPG1148-7

White Text

T1

#446A70

RGB: 68, 106, 112

CMYK: 76, 46, 47, 17

PPG1148-6

White Text

T2

#82AAAD

RGB: 130, 170, 173

CMYK: 51, 22, 30, 0

PPG1148-5

Black Text

T3

#BAD2D3

RGB: 186, 210, 211

CMYK: 27, 8, 15, 0

PPG1148-3

Black Text

T4

#E1EEEE

RGB: 225, 238, 238

CMYK: 11, 1, 5, 0

PPG1148-1

Black Text

T5

#853A28

RGB: 133, 58, 40

CMYK: 31, 82, 87, 33

PPG1067-7

White Text

R1

#B25B39

RGB: 178, 91, 57

CMYK: 23, 72, 85, 11

PPG1191-7

White Text

R2

#E39D7A

RGB: 227, 157, 122

CMYK: 9, 43, 53, 0

PPG1192-5

Black Text

R3

#E9C1A4

RGB: 233, 193, 164

CMYK: 7, 25, 34, 0

PPG1195-4

Black Text

R4

#F3DBCB

RGB: 243, 219, 203

CMYK: 3, 14, 17, 0

PPG1195-3

Black Text

R5

#9C6928

RGB: 156, 105, 40

CMYK: 32, 58, 100, 17

PPG16-15

White Text

Y1

#B97C2B

RGB: 185, 124, 43

CMYK: 24, 53, 100, 7

PPG1207-7

Black or large white

Y2

#DDB378

RGB: 221, 179, 120

CMYK: 13, 29, 60, 0

PPG1207-5

Black Text

Y3

#E5CFA8

RGB: 229, 207, 168

CMYK: 10, 17, 36, 0

PPG1207-4

Black Text

Y4

#EFE2C7

RGB: 239, 226, 199

CMYK: 6, 9, 22, 0

PPG1207-3

Black Text

Y5

White Text #384A66

RGB: 56, 74, 102

CMYK: 84, 69, 39, 24

PPG1164-7

B1

White Text #627188

RGB: 98, 113, 136

CMYK: 67, 51, 33, 8

PPG1164-6

B2

Black Text #8290A6

RGB: 130, 144, 166

CMYK: 53, 38, 24, 1

PPG1164-5

B3

Black Text

#AEBBD0

RGB: 174, 187, 208

CMYK: 31, 20, 9, 0

PPG1164-4

B4

Black Text

#D6DFE7

RGB: 214, 223, 231

CMYK: 15, 7, 5, 0

PPG1164-3

B5

Black Text

#DEB408

RGB: 222, 180, 8

CMYK: 0, 18, 100, 15

PPG1210-6

AY

Black Text

#9AB329

RGB: 154, 179, 41

CMYK: 32, 0, 100, 19

PPG1219-6

AG

White Text #242133

RGB: 36, 33, 51

CMYK: 81, 78, 51, 61

PPG1013-7

PH

PPG1207-1

W2

PPG1001-1

W1

Make things pop against darker colors by using accent colors (above) as a splash of brilliance, like in a button, an icon, or a thin border.

Lighter value colors in the bottom three rows are for maps, charts, graphs, etc. when you need extra colors that harmonize with the darker color options.

ACCENT COLORS MAIN COLORS

WEBSITE HEADER

WHITE PAINTS

UPDATED 03.01.2024 NAPA COUNTY BRANDING

BRAND COLORS

Squares are digital colors and circles are their closest match in PPG paint colors. Text on the color blocks indicates the best ADA-compliant option for text color over each color. Standard text is 12pt and large text means 18pt+.

For easy reference, each color set has a unique two-character ID code in bold.

Contemporary | K-14561 18" grab bar

Available Colors/Finishes Color tiles intended for reference only.

BN Vibrant Brushed Nickel BV Vibrant Brushed Bronze BL Matte Black 2MB Vibrant Brushed Moderne Brass BGP Vibrant Brushed Graphite

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 18:11 - US-CA

https://www.kohler.com/ https://www.kohler.ca/

Contemporary | K-14562 24" grab bar

Features

24" (610 mm) bar

Contemporary styling matches any decor

Available Colors/Finishes Color tiles intended for reference only.

SN Vibrant Polished Nickel BV Vibrant Brushed Bronze BL Matte Black BGP Vibrant Brushed Graphite

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-28-2026 18:1 - US-CA

K-14564 Contemporary 36" grab bar

Features

36" (914 mm) bar

Contemporary styling matches any decor

Available Colors/Finishes Color tiles intended for reference only.

SN Vibrant Polished Nickel BS Brushed Stainless BV Vibrant Brushed Bronze BL Matte Black 2MB Vibrant Brushed Moderne Brass BGP Vibrant Brushed Graphite

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-28-2026 18:4 - US-CA

Buckley™ | K-35933 Robe hook

Features

Coordinates with other products in the Buckley collection

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Codes/Standards None Applicable

Material

Premium metal construction for durability and reliability

KOHLER finishes resist corrosion and tarnishing

Recommended Products/Accessories

K-23723 Faucet cleaner

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Ø 2-7/16" (62 mm)

2-15/16" (75 mm)

3-15/16" (100 mm)

Installation

Installation hardware included

Installation Notes Install this product according to the installation instructions.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Buckley™ | K-35934 Toilet paper holder

Features

Coordinates with other products in the Buckley collection

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

Codes/Standards None Applicable

Material

Premium metal construction for durability and reliability

KOHLER finishes resist corrosion and tarnishing

Recommended Products/Accessories

K-23723 Faucet cleaner

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

3-11/16" (94 mm)

6-1/4" (159 mm)

8-11/16" (221 mm)

Ø 2-7/16" (62 mm)

Installation

Installation hardware and template included

Installation Notes Install this product according to the installation instructions.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

Buckley™ | K-35932 24" towel bar

Features

24" (610 mm) bar

Coordinates with other products in the Buckley collection

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

Codes/Standards None Applicable

Material

Premium metal construction for durability and reliability

KOHLER finishes resist corrosion and tarnishing

Recommended Products/Accessories

K-23723 Faucet cleaner

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

26-7/16" (672 mm)

24" (610 mm)

Ø 2-7/16" (62 mm)

3-11/16" (94 mm)

Installation

Installation hardware and template included

Installation Notes Install this product according to the installation instructions.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:4 - US-CA

1/2 Inch Thick Cork Board – Natural Tan Cork Sheet

1/2" thick natural cork boards with Adhesive-backed. Dense fine grain extruded cork sheet used for tackable surfaces.

Diverse Cork Sheet Options A 1/2 inch thick cork board offers numerous applications in both home and professional settings. From classic bulletin board designs to creative wall coverings, the versatility of cork sheets is unmatched.

These natural cork boards provide excellent acoustic and thermal insulation, making them an ideal choice for soundproofing projects and even as flooring materials. Moreover, cork's natural properties act as a moisture barrier, promising durability over time.

https://www.bangorcork.com/sample-request https://www.bangorcork.com/sample-request https://www.bangorcork.com/1-2-Inch-tan-cork/newReview https://www.bangorcork.com/CBL-B5124B-24-x-36-x-3_4 https://www.bangorcork.com/CBL-B5124B-24-x-36-x-3_4 https://www.bangorcork.com/48-x-100-x-1-4-Cork-Roll https://www.bangorcork.com/48-x-100-x-1-4-Cork-Roll https://www.bangorcork.com/CBL-BSNU28-1-2x24x36 https://www.bangorcork.com/CBL-BSNU28-1-2x24x36 https://www.bangorcork.com/48-x-1-4-Cork-Roll-Cut-to-Length https://www.bangorcork.com/48-x-1-4-Cork-Roll-Cut-to-Length

MHEU1738X

1.7 cu. ft. Smart Over-the-Range Convection Microwave Oven with Air Fry

K E

Y F

E A

T U

R E

S

1.7 cu.ft. Oven Capacity WideViewTM Widow PrintProofTM Stainless SteelSensor Cooking Air Fry Touchless Lighting Wi-Fi Connect (ThinQ® Technology) ThinQ UP Auto Cook

SUMMARY

Oven Capacity (cu.ft.) 1.7 cu.ft.

Type Over-the-Range Microwave Color PrintProof™ Stainless Steel

FEATURES

Microwave Power Output (W) 950 Convection Power Output (W) 1550

Exterior Design WideView™ Window (One body frame Monitor look)

Control Type Glass Touch (SmoothTouch™) Backlit Control Panel Yes Control Location Bottom Display White LED Scrolling, 2 Lines EasyClean® Interior No (STS)

COOKING FEATURES

Convection Yes Air Fry Yes Air Sous-Vide Yes Defrost Auto/ Time Proof Yes Warm Yes Power Levels for MW 10

Sensor Function Yes (19) Sensor Reheat (6), Sensor Cook (2), Popcorn (1)

Auto Cook

Yes(34) Auto Defrost(5),Steam Cook(7), Soften(4), Melt(4), More Modes (7EA), Warm (1EA), Proof (1EA), Manual Cook(5EA)

Custom Settings Yes

CONVENIENCE FEATURES

Wi-Fi Connect (ThinQ®) Yes ThinQ UP Yes ExtendaVentTM 2.0 No Racks 1 Turntable Diameter (Inches) 13.5" Clock Yes Kitchen Timer Yes Completion Beeper Yes Turntable On/Off Yes Add 30 Second Yes Included Accessories Metal Tray, Steam Bowl, Metal Rack, Tray, Crisp Touchless Light Yes Easyclean Mode Yes

Air Fry Control Panel ThinQ App

© 2025 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 3/6/2026

P R

O D

U C

T F

E A

T U

R E

S

LIGHTING

Lighting (Exterior/ Interior) LED Lighting

SAFETY FEATURES

Child Lock Yes

VENTING SYSTEM

Filtration Charcoal Filter Exhaust Grease Filter 2 Power Levels 4 Vent Grille Type Hidden Vent Air Flow (CFM) 300

MATERIALS AND FINISHES

All Available Colors PrintProofTM Stainless Steel PrintProofTM Finish Yes Interior Color Stainless Steel Handle Type One Body

SMART FEATURES

ThinQ® (Wi-Fi Enabled) Yes ThinQ UP Yes

Voice Control Google Assistant Amazon Alexa

Smart Receipt (3rd Party Recipe App) No

Proactive Customer Care Yes Smart DiagnosisTM Yes

ACCESSORIES

Crispy Tray Yes

POWER/ RATING

Volts 120/ 60 Amps/ Watts 14.5A/ 1700W

DIMENSIONS/ CLEARANCES/ WEIGHT

Cavity (WxHxD) 21 10/16"x 9 12/16"x 14 4/16" Exterior (WxHxD) (without or with handle) 29 14/16"x 16 8/16"x 16 6/16"

Net Weight (lbs) 72.6 Shipping Weight (lbs) 85.8 Shipping Dimensions (WxHxD) 33 7/16x 21 x 19 5/16

LIMITED WARRANTY

Parts and Labor 2 Year

UPC CODE

MHEU1738X 048231349697

MHEU1738X

Smart Over the Range Convection Microwave

HOME APPLIANCES

IM

P

O R

TA

N

T QUICK INSTALL & CLEARANCES

For full installation directions/clearances please refer to the corresponding User Manual and Installation Guide.

DIMENSIONS

Cavity (WxHxD) 21 10/16"x 9 12/16"x 14 4/16"

Exterior (WxHxD) (without or with handle) 29 14/16"x 16 8/16"x 16 6/16"

Net Weight (lbs) 72.6

Shipping Weight (lbs) 85.8

Shipping Dimensions (WxHxD) 33 7/16x 21 x 19 5/16

POWER SOURCE

Volts 120 / 60

Amps / Watts 14.5A /1700W

PRODUCT DIMENSIONS

INSTALLATION

CONNECTIONG THE DRAIN HOSE

© 2025 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 2/20/2026

WARNING

To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this product, follow basic precautions, including the following:

Installation

• This appliance should not be installed by anyone except properly qualified service personnel.

• You will need two people to install this appliance. It is heavy and could cause personal injury if not handled properly.

• Avoid Electric Shock. Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed behind the wall. You could get an electric shock if you contact electrical wires with your drill bit.

Locate and disconnect the power to any electrical circuits that could be affected by installing this appliance. If you do not disconnect the power, you could get an electric shock.

• This appliance must be grounded.

If there is an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord which includes a grounding wire with a grounding plug.

• Place the plug into a properly installed and grounded outlet

IMPORTANT SAFETY INSTRUCTIONS

Before You Start

Be sure to read the following safety instructions

Read the entire manual before you begin. The model number plate is located on the oven front.

The mounting plate is located on the back side of the microwave oven

Three-pronged (grounding) plug

Properly polarized and grounded outlet

• Do not use an extension cord.

• Keep the power cord dry and do not pinch or crush it.

Failure to follow this instruction may cause a fire hazard.

• Do not, under any circumstances, remove the power supply cord grounding prong.

• If you use the grounding plug improperly, you risk electric shock and/or fire.

Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not completely understand the grounding instructions.

• Do not use a fuse in the neutral or grounding circuit.

• Improper grounding could result in electric shock, fire or other personal injury.

16 6/18"

16 6/16"29 14/16"

Be sure you have enough space (minimum vertical and horizontal clearance).

Maximum 13": cabinet depth

Minimum 30": cabinet opening width

Minimum 30": clearance from bottom of cabinet to cooking surface or countertop before installation. (Use templates included with installation instructions.)

Grounded Outlet (inside upper cabinet)

Power Supply Cord Hole

TORNADO FLUSH CEFIONTECT

FEATURES

sticking to porous, ceramic surfaces

MODELS

• MS776124CSG (#01)

With CEFIONTECT ceramic glaze & includes SS124 SoftClose® seat

COMPONENTS

• C776CEGT40

Elongated bowl with CEFIONTECT

• ST776SA

Tank and cover only

• SS124

SoftClose seat

OPTIONAL COMPONENTS

• THU808(#01, #03, #11, #12, #51, #PN, #BN, #RB)-A

Trip Lever - Cotton, Bone, Colonial White, Sedona Beige, Ebony, Polished Nickel, Brushed Nickel, Oil Rubbed Bronze)

PRODUCT SPECIFICATION

The two-piece high-efficiency Tornado Flush system toilet shall be 1.6 GPF/6.0 LPF. Toilet shall have CEFIONTECT ceramic glaze and be at Regular Height.

Toilet shall have high-profile tank, elongated front bowl, SoftClose seat and Chrome trip lever. Toilet shall be TOTO Model MS776124CSG#01.

COLORS/FINISHES

• #01 Cotton

MS776124CSG

Drake® Two-Piece Toilet, 1.6 GPF

CODES/STANDARDS

and others

Ph: (888) 295-8134 | Fax: (800) 699-4889 | www.totousa.com | © TOTO USA

These dimensions and specifications are subject to change without notice

SPECIFICATIONS

DIMENSIONS

# SS-01992 v.02

MS776124CSG

Drake® Two-Piece Toilet, 1.6 GPF

Shipping Dimensions

C776CEGT40

29-3/4" L x 15" W1 x 10-5/8" W2 x 16-1/4" H

ST776SA

18-3/4" L x 8-7/8" W x 16-1/4" H

Shipping Weight

C776CEGT40

57 lbs.

ST776SA

32 lbs.

Material Vitreous China

Warranty One Year Limited Warranty

Trap Seal 2-1/8"

Rough-in 12"

Trap Diameter 2-1/8"

Water Surface 9" x 6-7/8"

Min. Water Pressure 8 psi (Flowing)

Flush System TORNADO FLUSH®

Water Use 1.6 GPF (6.0 LPF)

17 3/16" [436 mm]

CST776C(S)(E)G w/ SS124

29" [736 mm]

16 1/8" [410 mm]

1 5/8" [40 mm] Finished

Floor Finished Wall

* Suggested Dimension

Finished Wall

Supply as Req'd

5 1/2" [140 mm]

13/16" [20 mm]

7 3/8" [187 mm]

18 1/2" [470 mm]

Water Level 5 1/2"

[140 mm]

* 4 5/16" [109 mm]

24 7/16" [620 mm]

12" [305 mm]

9 13/16" [250 mm]

6" [152 mm]

* 7 1/2" [190 mm]

14 15/16" [380 mm]

5 1/2" [140 mm]

14 1/16" [357 mm]

18 11/16" [474 mm]

11 13/16" [300 mm]

7 7/8" [200 mm]

1 1/16" [28 mm]

1 7/16" [37 mm] 1 7/8"

[47 mm]

SEAT HEIGHT

16 3/8"

[417 mm]

2 3/8" [60 mm]

28 5/16" [720 mm]

14" [355 mm]

3/16" [4 mm]

Ø1 15/16" [Ø50 mm]

4 5/8" [117 mm]

Double Sanitary Tee / Sanitary CrossDouble Combination Wye / 1/8 Bend

YES NO

Important Note:

Back-to-Back Toilet Installations:

TOTO USA, Inc. recommends the use of a nationally listed, double sanitary tee-wye only, in vertical waste stacks, in accordance with the stipulations noted in the majority of nationally recognized plumbing codes.

INSTALLATION NOTES

Back-to-Back Toilet Installations:

TOTO recommends the use of a nationally listed, double sanitary tee-wye only, in vertical waste stacks, in accordance with the stipulations noted in the majority of nationally recognized plumbing codes.

To maintain adequate wall gap between the back of the tank and wall, mount the floor flange at a nominal 12” rough-in distance.

Buckley™ | K-TS35937-4H Rite-Temp® bath and shower trim kit, 1.5 gpm

Features

Single-function 1.5 gpm (5.7 lpm) showerhead

A single handle controls both on/off activation and temperature setting

MasterClean™ sprayface features an easy-to-clean surface that withstands mineral buildup and maximizes spray performance

5-1/16" (129 mm) diverter bath spout with slip-fit connection

Box includes: Showerhead, shower arm and flange, faceplate with lever handle, diverter bath spout with 1/2" slip-fit connection

This product can help a building earn Water Efficiency points in LEED® Green Building Rating System

Coordinates with other products in the Buckley collection

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Codes/Standards

ASME A112.18.1/CSA B125.1

DOE - Energy Policy Act 1992 EPA WaterSense® California Energy Commission (CEC)

Technical Information All product dimensions are nominal.

Handle Handle Style/ Type: Lever

Spout Spout Reach: 5-1/16" (128 mm)

Flow Rate Shower/Rainhead Rated Maximum Flow:

1.5 gpm (5.7 l/min)

Handshower Rated Maximum Flow:

1.5 gpm (5.7 l/min)

Valves

Required Valve: Pressure Balance

Material

Premium material construction with metal handle ensures reliability and durability

KOHLER finishes resist corrosion and tarnishing

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

3-3/16" (81 mm)

1/2 -14 NPT

Ø 2-9/16" (65 mm)

6-1/2" (165 mm) Typical

2-11/16" (68 mm)

Ø 1-1/4" (32 mm) Max

5-1/16" (129 mm)

Slip-fit:

Extend 5/8" OD tube 2-3/4" (70 mm) from finished wall.

Ø 6-1/2" (165 mm)

3-7/8" (98 mm)

4-9/16" (116 mm)

K-8300 Valve Series

K-2971-KS,

K-304 Valves

Finished Wall

*If 3-1/2" (89 mm) to 4-1/4" (108 mm) use deep roughing-in kit.

Installation

Trim only; requires valve to complete installation (sold separately)

Installation Notes Install this product according to the installation instructions.

Install the product according to the installation guide.

NOTICE: Risk of product damage. Long screws, for installing trim, can damage the K-2971-KS valve. Consult the trim installation guide to verify if the thin wall installation kit (88526) is needed.

Install straight pipe or tube drop of 7" (178 mm) to 18" (457 mm) with single elbow between the valve and the wall-mount spout.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Buckley™ | K-TS35938-4H Rite-Temp® shower trim kit, 1.5 gpm

Features

Single-function 1.5 gpm (5.7 lpm) showerhead

A single handle controls both on/off activation and temperature setting

MasterClean™ sprayface features an easy-to-clean surface that withstands mineral buildup and maximizes spray performance

Box includes: Showerhead, shower arm and flange, faceplate with lever handle

Coordinates with other products in the Buckley collection

This product can help a building earn Water Efficiency points in LEED® Green Building Rating System

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-28-2026 18:2 - US-CA

Codes/Standards

ASME A112.18.1/CSA B125.1

DOE - Energy Policy Act 1992 EPA WaterSense® California Energy Commission (CEC)

Technical Information All product dimensions are nominal.

Handle Handle Style/ Type: Lever

Flow Rate Shower/Rainhead Rated Maximum Flow:

1.5 gpm (5.7 l/min)

Handshower Rated Maximum Flow:

1.5 gpm (5.7 l/min)

Valves

Required Valve: Pressure Balance

Material

Premium material construction with metal handle ensures reliability and durability

KOHLER finishes resist corrosion and tarnishing

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-28-2026 18:2 - US-CA

3-3/16" (81 mm)

1/2 -14 NPT

Ø 2-9/16" (65 mm)

6-1/2" (165 mm)

Ø 6-1/2" (165 mm)

3-7/8" (98 mm)

4-9/16" (116 mm)

K-8300 Valve Series

K-2971-KS,

K-304 Valves

Finished Wall

*If 3-1/2" (89 mm) to 4-1/4" (108 mm) use deep roughing-in kit.

Installation

Trim only; requires valve to complete installation (sold separately)

Installation Notes Install this product according to the installation instructions.

Install the product according to the installation guide.

NOTICE: Risk of product damage. Long screws, for installing trim, can damage the K-2971-KS valve. Consult the trim installation guide to verify if the thin wall installation kit (88526) is needed.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-28-2026 18:2 - US-CA

Avec® | K-25832-LA 60" x 36" alcove bath, left drain

Features

Slotted overflow allows for deep soaking

13-1/4" (337 mm) deep-soaking depth provides a relaxing bathing experience

Integral lumbar support and neck rest offer extra comfort while bathing

Low step-over height allows easy entry and exit

Integral overflow reduces installation time

Integral apron creates a clean, finished look

Textured bottom surface

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 19:40 - US-CA

Codes/Standards ADA compliant when installed to the specific requirements of these regulations.

CSA B45.5/IAPMO Z124

ASTM E162

ASTM E662

ADA

ICC/ANSI A117.1

Technical Information All product dimensions are nominal.

Drain Location: Left

Drain Hole Diameter: 2-1/4" (57 mm)

Minimum Flat for Door: 2-15/16" (75 mm)

Basin Area, Bottom: 43-1/2" x 24-7/8" (1105 mm x 632 mm)

Basin Area, Top: 55-15/16" x 29-1/2" (1421 mm x 749 mm)

Water Depth: 13-1/4" (337 mm)

Water Capacity: 65.4 gal (247.6 L)

Minimum Floor Load: 43.4 lbs/ft²

Weight: 106.24 lbs (48.2 kg)

Material

Acrylic

Warranty See website for detailed warranty information.

KOHLER® Plastic Baths and Shower Bases Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 19:40 - US-CA

1-1/2" Bath Drain

36" (914 mm)

1-1/4" (32 mm)

Drop-in Rim Detail

19-3/8" (492 mm)

No change in measurements if connected with drain illustrated. (1475082)

19-3/8" (492 mm)

Lumbar Angle 35°

1-1/4" (32 mm)

1-3/8" (35 mm)

2" (51 mm)

15-7/16" (392 mm)

3-3/4" (95 mm) 60" (1524 mm)

10-9/16" (268 mm)

Installation

Alcove

Left drain

Installation Notes Install this product according to the installation instructions.

Measure your actual product for rough-in details.

The hot water supply should be 70% of the capacity of the bath or greater. Installations will vary.

ADA compliant when installed to the specific requirements of these regulations.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 19:40 - US-CA

Caxton® | K-2209 17" oval undermount bathroom sink

Features

Oval basin with unglazed underside

Overflow drain

No faucet holes; requires wall- or counter-mount faucet

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

0 White HW1 Honed White 96 Biscuit 7 Black Black HDN Honed Dune HB1 Honed Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 3:8 - US-CA

Codes/Standards ADA, CSA B651 compliant when installed to the specific requirements of these regulations.

ASME A112.19.2/CSA B45.1

ADA

ICC/ANSI A117.1

CSA B651

Technical Information With Overflow: Yes

Drain Hole Diameter: 1-3/4" (44 mm)

Basin Configuration: Single Bowl

Basin Length: 15-1/4" (387 mm)

Basin Width: 12-1/4" (311 mm)

Basin Depth: 5-3/4" (146 mm)

Material

Vitreous china

Recommended Products/Accessories

K-23726 Drain treatment

K-8998 Adjustable P-trap with tubing outlet, 1-1/4" x 1-1/4"

K-23725 Cast iron cleaner

Warranty See website for detailed warranty information.

KOHLER® Vitreous China Bathroom Sink Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 3:8 - US-CA

17-1/16" (433 mm)

8-9/16" (217 mm)

10-3/4" (273 mm)

3-1/4" (83 mm)

7/8" (22 mm)

13-7/8" (352 mm)

7-5/8" (194 mm)14"

(356 mm) 13-1/8" (333 mm)

1-1/4" OD

3/8" Hot 3/8" Cold 1-1/2" (38 mm)

4" (102 mm)

ADA Drain Outlet of FittingLC

5-1/8" (130 mm)

1/2" (13 mm)

3/8" (10 mm)

5/8" (16 mm)

34" (864 mm) 27"

(686 mm) Min

8" (203 mm)Min

24" (610 mm)2-3/8" (60 mm)

11" (279 mm) 9" (229 mm) Min

Recommended ADA Installtion

Marble Installation

Wood Installation

Sealant

Sealant

Installation

Undermount

Installation Notes Install this product according to the installation instructions.

NOTICE: Countertop manufacturer or cutter must use the current product template available at www.kohler.com, or by calling 1-800- 4KOHLER. Kohler Co. is not responsible for cutout errors when the incorrect cutout template is used.

Product dimensions are nominal and may vary per ASME A112.19.2 tolerances.

ADA, CSA B651 compliant when installed to the specific requirements of these regulations.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 3:8 - US-CA

Buckley™ | K-35953-4 Widespread bathroom sink faucet, 1.2 gpm

Features

Two Lever handles control both on/off activation and temperature setting

1.2 gpm (4.5 lpm) maximum flow rate at 60 psi (4.14 bar)

KOHLER® ceramic disc valves exceed industry longevity standards for a lifetime of durable performance

Metal touch-activated drain with 1-1/4" tailpiece

This product can help a building earn Water Efficiency points in LEED® Green Building Rating System

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome BN Vibrant Brushed Nickel BL Matte Black

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Codes/Standards ADA, OBC, CSA B651 compliant when installed to the specific requirements of these regulations.

ASME A112.18.1/CSA B125.1

NSF/ANSI/CAN 372

NSF/ANSI/CAN 61

DOE - Energy Policy Act 1992 EPA WaterSense® California Energy Commission (CEC)

ADA

ICC/ANSI A117.1

CSA B651

OBC

Technical Information All product dimensions are nominal.

Handle Handle Style/ Type: Lever

Spout Spout Reach: 5" (127 mm)

Drain With Overflow: Yes

Flow Rate Faucet Flow Rate: 1.2 gpm (4.5 l/min)

Valves

Included Valve: Ceramic disc

Material

Premium metal construction for durability and reliability

Recommended Products/Accessories

K-23726 Drain treatment

K-23723 Faucet cleaner

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

4-13/16" (122 mm)

Ø 2-1/8" (54 mm)

8-1/2" (216 mm)

1-1/4" OD

7-3/16" (183 mm)

5" (127 mm)

3" (76 mm)

3-9/16" (90 mm)2-3/4"

(70 mm)

Ø 1-1/8" (29 mm)

3" (76 mm)

Ø 2" (51 mm)

1-1/4" (32 mm) Max

1/2-14NPSM-2A

Ø 1-1/4" (32 mm)

Ø 2-1/8" (54 mm)

8" (203 mm) Min 16" (406 mm) Max

Installation

For 8" – 16" (203 – 406 mm) centers

Preattached flexible supply lines simplify installation

Installation Notes Install this product according to the installation instructions.

ADA, OBC, CSA B651 compliant when installed to the specific requirements of these regulations.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 19:1 - US-CA

Vault™ | K-3821 32" undermount single-bowl large kitchen sink

Features

36" minimum base cabinet width

Single bowl

9" (229 mm) depth provides generous workspace

Rear drain placement increases cabinet storage space underneath sink

Includes installation hardware

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

NA Stainless Steel

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 21:10 - US-CA

Codes/Standards

ASME A112.19.3/CSA B45.4

Technical Information All product dimensions are nominal.

Drain Hole Diameter: 3-3/4" (94 mm)

Minimum Base Cabinet Width: 36" (914 mm)

Basin Configuration: Single Bowl

Basin Length: 30-1/4" (768 mm)

Basin Width: 16-9/16" (420 mm)

Basin Depth: 9" (229 mm)

Material

Premium 18-gauge stainless steel

Recommended Products/Accessories

K-23726 Drain treatment

K-23729 Stainless steel cleaner

K-8801 Sink drain and strainer with tailpiece

K-8799 Sink drain and strainer basket, less tailpiece

K-6429 Utility rack

K-6644 Stainless steel sink rack

K-6667 Wood cutting board

K-11352 Disposal flange with stopper

Warranty See website for detailed warranty information.

KOHLER® Stainless Steel Sinks Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 21:10 - US-CA

16" (406 mm)

6-5/16" (160 mm)

32" (813 mm) 18-5/16" (465 mm)

9-1/4" (235 mm)

7/8" (22 mm)

Installation

Undermount

Installation Notes Install this product according to the installation instructions.

Allow 3/4" (19 mm) clearance beyond the back of the bowl for the wood cutting board (optional accessory).

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-30-2026 21:10 - US-CA

Simplice® | K-596 Pull-down kitchen sink faucet with three-function sprayhead

Features

Three-function pull-down sprayhead with touch-control allows you to switch between stream, Sweep® spray and Boost technology

Sweep® spray creates a wide, forceful blade of water for superior cleaning

Boost technology increases the flow rate by 30% with the press of a button

KOHLER® ceramic disc valves exceed industry longevity standards for a lifetime of durable performance

ProMotion® technology's light, quiet braided hose and swiveling ball joint make the pull-down sprayhead easier and more comfortable to use

MasterClean™ sprayface features an easy-to-clean surface that withstands mineral buildup and maximizes spray performance

High-arch spout offers superior clearance for filling pots and cleaning

Single handle is simple to use and makes adjusting water temperature easy

Temperature memory allows faucet to be turned on and off at the temperature set during prior usage

1.5 gpm (5.7 lpm) maximum flow rate at 60 psi (4.14 bar)

DockNetik® secure docking system locks sprayhead into place when not in use

Sustainability

Available Colors/Finishes Color tiles intended for reference only.

CP Polished Chrome VS Vibrant Stainless BL Matte Black 2MB Vibrant Brushed Moderne Brass

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 21:22 - US-CA

Codes/Standards ADA, CSA B651 compliant when installed to the specific requirements of these regulations.

ASME A112.18.1/CSA B125.1

NSF/ANSI/CAN 372

NSF/ANSI/CAN 61

DOE - Energy Policy Act 1992 California Energy Commission (CEC)

ADA

ICC/ANSI A117.1

CSA B651

Technical Information All product dimensions are nominal.

Handle Handle Style/ Type: Lever

Spout Spout Reach: 9" (229 mm)

Flow Rate Faucet Flow Rate: 1.5 gpm (5.7 l/min)

Valves

Included Valves: Ceramic disc, Thermostatic, Volume Control

Material

Premium metal construction for durability and reliability

KOHLER finishes resist corrosion and tarnishing

Recommended Products/Accessories

K-23723 Faucet cleaner

K-77687 Single replacement filter cartridge

K-77688 Two-pack replacement filter cartridges

K-77685 Single-cartridge water filtration system

K-77686 Double-cartridge water filtration system

Warranty See website for detailed warranty information.

KOHLER® Faucet Lifetime Limited Warranty

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 21:22 - US-CA

Escutcheon Width Ø 2" (51 mm) for single hole Ø 2-1/2" (64 mm) for three hole

16-5/8" (422 mm)

9-5/8" (244 mm)

9" (229 mm)

31-1/4" (794 mm)

Supply Hoses with 3/8" Compression Fitting

2-1/2" (64 mm) Max

Ø 1-5/16"

6-1/4" (159 mm)

3-15/16" (100 mm)

Ø 2" (51 mm)

10-1/2" (267 mm)

2-1/4" (57 mm)

Installation

For single-hole or three-hole installation (escutcheon plate included)

Flexible supply lines and installation ring simplify installation

Installation Notes Install this product according to the installation instructions.

ADA compliant for faucet handles only.

ADA compliant for faucet handles only ADA, CSA B651 compliant when installed to the specific requirements of these regulations.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current specification sheet, go to www.kohler.com USA or www.kohler.ca Canada.

5-12-2026 21:22 - US-CA

Specification Submittal Data / Panasonic Precision Spot Ventilation Fan with Dual Sensor Technology

FV-0511VQC1

FV-0511VQC1

7-3/8

10-1/4 10-1/4

13 13

4" or 6" duct

VF17563SS0917

Description Ventilating fan shall be low noise ceiling mount type rated for continuous operation. Fan shall be ENERGY STAR® rated and certified by the Home Ventilating Institute (HVI). Evaluated by the Underwriters Laboratories and conform to both UL and cUL standards.

Motor/Blower:

• Enclosed brushless ECM motor technology rated for continuous run.

• Fan ventilation rates shall be manually adjustable for 50-80-110 CFM.

• Power rating shall be 120 volts and 60 Hz.

• Fan shall be UL and cUL listed for tub/shower enclosure when GFCI protected.

• Motor equipped with thermal–cutoff fuse.

• Removable with permanently lubricated plug-in motor.

Housing:

• 26 gauge Zinc-Aluminum-Magnesium (ZAM) housing.

• Integrated dual 4” or 6” diameter duct adapter.

• Built-in damper reduces back drafting and helps with blower door testing.

• Built-in metal flange provides blocking for penetrations through drywall as an Air Barrier, and assists with the decrease in leakage in the Building Envelope during blower door testing.

•…