ATTACHMENT K.pdf
PDF 583 KB Posted
- Attached to
- DISTRICT 3 ON CALL PIPE REPAIR
- Solicitation number
- 5400030105
- Issued by
- Richland County, South Carolina
About this file
Summary
Attachment K is an approved products list for traffic control devices in work zones issued by the South Carolina Department of Transportation (SCDOT) in July 2018. The document establishes pre-approved traffic control devices that comply with the Federal Highway Administration's directive requiring all devices used on the National Highway System to meet the 1993 National Cooperative Highway Research Program Report 350 standards. The devices are categorized into four classifications: Category I includes small, lightweight channelizing devices such as plastic traffic cones, oversized cones, portable plastic drums, and temporary surface-mounted delineator posts; Category II includes traffic control devices with mass of 45 kilograms or less, such as barricades and vertical panels; Category III includes heavier devices exceeding 45 kilograms, such as truck-mounted attenuators and longitudinal barriers; and Category IV includes trailer-mounted devices such as advance warning arrow panels and changeable message signs, for which no products have currently been approved. The list identifies multiple manufacturers for each approved device type, specifying whether products are approved for use by SCDOT forces only, contractor forces only, or both.
The evaluation process requires manufacturers and vendors to submit product specifications, brochures, and self-certification letters demonstrating compliance with NCHRP Report 350 requirements, or FHWA acceptance letters for Category II, III, and IV devices. The SCDOT reserves the right to reject products, place limitations on use, require additional testing, or mandate in-service evaluation. The "CONSUMER" column in the product listings indicates acceptable market usage: "SCDOT" designates devices for SCDOT forces only, "CONTRACT" designates devices for contracted work forces only, and "ALL" indicates devices may be utilized by both SCDOT and contractor forces. Contract work initiated after May 1, 2012, must reflectorize barricades with Type VIII or Type IX prismatic retroreflective sheeting. Contact information for manufacturers is provided at the end of the document, with additional information available from the SCDOT Traffic Engineering office.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| AMENDMENT 1.pdf | ||
| ATTACHMENT F.pdf | ||
| ATTACHMENT E.pdf | ||
| ATTACHMENT J.pdf | ||
| ATTACHMENT I.pdf | ||
| ATTACHMENT G.pdf | ||
| SOLICITATION 5400030105.pdf | ||
| ATTACHMENT D.pdf | ||
| ATTACHMENT H.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
ATTACHMENT K JULY 2018
APPROVED PRODUCTS LIST
FOR
TRAFFIC CONTROL DEVICES
IN
WORK ZONES
NATIONAL COOPERATIVE HIGHWAY RESEARCH PROGRAM REPORT 350 STANDARDS
The Department pre-approves and lists all traffic control devices subject to impact by errant vehicles to be used on state construction and maintenance projects. These products must comply with the Federal Highway Administration’s directive mandating that all such devices, used on the National Highway System, must be crash tested and meet all requirements and regulations stipulated by the 1993 National Cooperative Highway Research Program Report 350, “Recommended Procedures for the Safety Performance Evaluation of Highway Features”.
All traffic control devices are divided into four categories.
Category I Devices -- Category I includes small and lightweight channelizing and delineating devices. Formal and informal crash testing and years of experience have shown that an impact with these devices will cause very little change in the speed of the impacting vehicle and that the passenger compartment of the striking vehicle is unlikely to be penetrated by any part of these devices. Included in this category are single-piece plastic traffic cones, oversized cones, portable plastic drums, and temporary surface mounted delineator posts without attachments such as signs or warning lights.
Category II Devices -- Category II includes traffic control devices that are not expected to produce significant vehicular velocity changes to impacting vehicles. Also, acceptable devices in this category shall not be capable of penetrating the windshield or causing vehicular instability during a crash. Included in this category are Types I, II, and III barricades, vertical panels, portable sign supports with roll-up signs, and other traffic control devices with a mass of 45 kilograms (100 pounds) or less.
Category III Devices -- Category III includes traffic control devices that are expected to cause significant vehicular velocity changes to impacting vehicles. These devices have a mass greater than 45 kilograms (100 pounds). Included in this category are truck mounted attenuators, portable terminal impact attenuators, longitudinal barriers, fixed ground mounted sign assemblies, and other traffic control devices that do not meet the definitions of Category I or II.
Category IV Devices -- Category IV includes trailer mounted traffic control devices. Included in this category are advance warning arrow panels, changeable message signs, portable traffic signals, and portable lighting equipment. The FHWA and AASHTO are evaluating methods for making these devices crashworthy. The target date for requiring these devices to meet NCHRP Report 350 requirements has not been determined. No Category IV devices have been approved at this time.
Each traffic control device must be evaluated prior to inclusion on the approved products list. The evaluation process requires the manufacturer or vendor to submit product specifications and a product brochure for each traffic control device to be considered. Also, the manufacturer must submit a self-certification letter certifying the device meets the requirements of NCHRP Report 350 for each of those devices included in Category I and a copy of the FHWA acceptance letter for those devices included in Categories II, III, and IV. Acceptance by the FHWA does not guarantee inclusion on this approved products list. The SCDOT reserves the right, as granted by the July 25, 1997 FHWA memorandum, “Action: Identifying Acceptable Highway Safety Features”, to reject a product or place limitations on its use, require additional testing, or require in-service evaluation.
The “CONSUMER” column indicates the acceptable market for each device. “SCDOT” indicates the device may only be utilized by SCDOT forces. “CONTRACT” indicates the device may only be utilized by forces contracted to conduct work on behalf of the SCDOT. “ALL” indicates the device may be utilized by SCDOT and contractor forces.
Contact information for each manufacturer is provided at the end of this document. Additional information is available from Will McConnell in Traffic Engineering.
July 2018
APPROVED WORK ZONE TRAFFIC CONTROL DEVICES
CATEGORY I
CONES
SEE 2007 STANDARD SPECIFICATIONS FOR HIGHWAY CONSTRUCTION, SECTION 603
DEVICE DESCRIPTION MANUFACTURER CONSUMER REMARKS
“MODEL RC90045C” SINGLE PIECE
TRAFFIC CONE
36” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH ORANGE BASE (10 LB.)
JBC SAFETY PLASTIC,
INC.
CONTRACT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (19-JUL-02)
“MODEL RC70032C” WIDE BODY
SINGLE PIECE TRAFFIC CONE
(For Retroreflective Collars – see Model RC70032C3M64)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH ORANGE BASE (7 LB.)
JBC SAFETY PLASTIC,
INC.
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (22-MAY-06)
“MODEL RS70032C” WIDE BODY
SINGLE PIECE TRAFFIC CONE
(For Retroreflective Collars – see Model RS70032C3M64)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH BLACK BASE (7 LB.)
JBC SAFETY PLASTIC,
INC.
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (13-JUN-06)
“MODEL RC70032CT” WIDE BODY
SINGLE PIECE TRAFFIC CONE
(For Retroreflective Collars – see Model RC70032CT3M64)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH ORANGE BASE (7 LB.)
JBC SAFETY PLASTIC,
INC.
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (22-MAY-06)
“MODEL RS70032CT” WIDE BODY
SINGLE PIECE TRAFFIC CONE
(For Retroreflective Collars – see Model RS70032CT3M64)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH BLACK BASE (7 LB.)
JBC SAFETY PLASTIC,
INC.
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (13-JUN-06)
(Category I Continued) CONES (Continued)
DEVICE
DESCRIPTION MANUFACTURER
CONSUMER REMARKS
“MODEL RC70032S” SLIM LINE
SINGLE PIECE TRAFFIC CONE
(For Retroreflective Collars – see Model RC70032S3M64)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH ORANGE BASE (7 LB.)
JBC SAFETY PLASTIC,
INC.
SCDOT
APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (22-MAY-06)
“MODEL RS70032S” SLIM LINE
Model RS70032S3M64)
WITH BLACK BASE (7 LB.)
“MODEL RC70045C” WIDE BODY
Model RC70045C3M64)
WITH ORANGE BASE (10 LB.)
“MODEL RS70045C” WIDE BODY
Model RS70045C3M64)
WITH BLACK BASE (10 LB.)
“MODEL RC70045S” SLIM LINE
Model RC70045S3M64)
“MODEL RS70045S” SLIM LINE
Model RS70045S3M64)
“MODEL RC90045C” WIDE BODY
Model RC90045C3M64)
36” FLUORESCENT ORANGE
ALL
“MODEL RS90045C” SINGLE PIECE
TRAFFIC CONE
Model RS90045CT3M64)
CONTRACT
“MODEL RC90055CT3M64” WIDE
BODY SINGLE PIECE TRAFFIC
CONE
WITH ORANGE BASE (12 LB.) WITH
RETROREFLECTIVE COLLARS
“MODEL RS90055CT3M64” WIDE
BODY SINGLE PIECE TRAFFIC
WITH BLACK BASE (12 LB.) WITH
RETROREFLECTIVE COLLARS
“MODEL 16414” WIDE BODY TWO
PIECE DW SERIES TRAFFIC CONE
Model Nos. 16536 or 16519)
28” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH BLACK
BASE (7 LBS.)
KIMBERLY-CLARK
PROFESSIONAL.
SELF-CERTIFICATION, (17-MAR-12)
“MODEL 16490” WIDE BODY TWO
Model Nos. 16557 or 17847)
28” RED/ORANGE POLYVINYL
BASE (10 LBS.)
“MODEL 16480” WIDE BODY TWO
Model Nos. 16532 or 17336)
36” RED/ORANGE POLYVINYL
BASE (10 LBS.)
“MODEL 16528” WIDE BODY TWO
Model No. 17850)
36” RED/ORANGE POLYVINYL
BASE (12 LBS.)
“MODEL 16479” WIDE BODY ONE
PIECE W SERIES TRAFFIC CONE
Model Nos. 16549 or 16538)
28” FLUOURESCENT ORANGE
WITH BASE (6.5 LBS.)
“MODEL 16496” WIDE BODY ONE
Model Nos. 16498 or 17418)
WITH BASE (7 LBS.)
“MODEL 16487” WIDE BODY ONE
Model Nos. 16560 or 16559)
WITH BASE (10 LBS.)
“MODEL 16484” WIDE BODY ONE
Model Nos. 16566 or 17851)
36” FLUOURESCENT ORANGE
“MODEL 16569” WIDE BODY ONE
Model Nos. 16571 or 16570)
36” FLUOURESCENT ORANGE
WITH BASE (12 LBS.)
“MODEL 2825-10” SINGLE PIECE
LAKESIDE PLASTICS
SELF-CERTIFICATION, (27-FEB-12)
“MODEL 2850-7” SINGLE PIECE
WITH BASE (7 LBS.)
LAKESIDE PLASTICS
SELF-CERTIFICATION, (27-FEB-12)
“MODEL 3650-8” SINGLE PIECE
WITH BLACK BASE (8 LB.)
LAKESIDE PLASTICS,
SELF-CERTIFICATION, (25-APR-01)
“MODEL 3650-10” SINGLE PIECE
“MODEL 3650-12” SINGLE PIECE
WITH BLACK BASE (12 LB.)
“MODEL SC-28-7” SINGLE PIECE
WIDE BODY TRAFFIC CONE
7 LB. - 28” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH
ORANGE BASE
SELF-CERTIFICATION, (11-JUL-11)
“MODEL SC-28-10” SINGLE PIECE
WIDE BODY TRAFFIC CONE
10 LB. - 28” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH
ORANGE BASE
SELF-CERTIFICATION, (11-JUL-11)
(Category I Continued) CONES (Continued)
DEVICE DESCRIPTION MANUFACTURER CONSUMER REMARKS
“MODEL SC-36-8” SINGLE PIECE
WIDE BODY TRAFFIC CONE
8 LB. - 36” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH
ORANGE BASE
LAKESIDE PLASTICS,
INC.
ALL APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (11-JUL-11)
“MODEL SC-36-10” SINGLE PIECE
WIDE BODY TRAFFIC CONE
10 LB. - 36” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH
ORANGE BASE
LAKESIDE PLASTICS,
INC.
ALL APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (11-JUL-11)
“MODEL SC-36-12” SINGLE PIECE
WIDE BODY TRAFFIC CONE
12 LB. - 36” RED/ORANGE POLYVINYL
CHLORIDE (PVC) PLASTIC WITH
ORANGE BASE
LAKESIDE PLASTICS,
INC.
ALL APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (11-JUL-11)
“MODEL SAS 7501-28” SINGLE
PIECE TRAFFIC CONE
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH BASE
SAS SAFETY
CORPORATION
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (17-NOV-15)
“MODEL SAS 7501-36” SINGLE
PIECE TRAFFIC CONE
36” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) PLASTIC
WITH BASE
SAS SAFETY
CORPORATION
ALL APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (17-NOV-15)
“UAT SERIES” 28 in. x 7 lb. CONE
(For Retroreflective Collars – see Models CWOR28-07 or CW3M28- 07)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) INJECTED
TRAFFIC CONE WITH 100% RECYCLED
BLACK BASE (7 LB.)
TAROKO
INTERNATIONAL
Distributed by
UAT, LLC
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (01-JAN-17)
“UAT SERIES” 28 in. x 10 lb. CONE
(For Retroreflective Collars – see Models CWOR28-10 or CW3M28- 10)
28” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) INJECTED
TRAFFIC CONE WITH 100% RECYCLED
BLACK BASE (10 LB.)
TAROKO
INTERNATIONAL
Distributed by
UAT, LLC
SCDOT APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (01-JAN-17)
“UAT SERIES” 36 in. x 10 lb. CONE
(For Retroreflective Collars – see Models CWOR36-10 or CW3M36- 10)
36” FLUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) INJECTED
TRAFFIC CONE WITH 100% RECYCLED
BLACK BASE (10 LB.)
TAROKO
INTERNATIONAL
Distributed by
UAT, LLC
ALL APPROVED NCHRP REPORT 350, (28-AUG-98), (WZ-3)
SELF-CERTIFICATION, (01-JAN-17)
“UAT SERIES” 36 in. x 12 lb. CONE
Models CWOR36-12 or CW3M36- 12)
POLYVINYL CHLORIDE (PVC) INJECTED
TRAFFIC CONE WITH 100% RECYCLED
BLACK BASE (12 LB.)
TAROKO
INTERNATIONAL
Distributed by
UAT, LLC
SELF-CERTIFICATION, (01-JAN-17)
“UAT NEXT GENERATION
TRAFFIC CONE NG3M28-07”
28” FLOURESCENT ORANGE
POLYVINYL CHLORIDE (PVC)
COMPOUND, 3M COLLARED WITH
BLACK BASE (7 LBS.)
SELF-CERTIFICATION, (25-SEP-17)
SCDOT ACCEPTANCE, (01-FEB-18)
TRAFFIC CONE NG3M28-10”
28” FLOURESCENT ORANGE
BLACK BASE (10 LBS.)
TRAFFIC CONE NG3M36-10”
36” FLOURESCENT ORANGE
BLACK BASE (10 LBS.)
TRAFFIC CONE NG3M36-12”
36” FLOURESCENT ORANGE
BLACK BASE (12 LBS.)
“28 PVCS” SINGLE PIECE TRAFFIC
28” (7 LB.) FUORESCENT ORANGE
POLYVINYL CHLORIDE (PVC) WIDE
BODY DESIGN WITH ORANGE BASE
WORK AREA
PROTECTION
CORPORATION
SELF-CERTIFICATION, (18-NOV-02)
“36 PVCS” SINGLE PIECE TRAFFIC
36” (10 LB.) RED/ORANGE POLYVINYL
CHLORIDE (PVC) WIDE BODY DESIGN
WITH ORANGE BASE
SELF-CERTIFICATION, (18-JAN-99)
“36 PVCH” SINGLE PIECE TRAFFIC
36” (12 LB.) RED/ORANGE POLYVINYL
CHLORIDE (PVC) WIDE BODY DESIGN
WITH ORANGE BASE
(Category I Continued)
OVERSIZED CONES
SEE 2007 STANDARD SPECIFICATIONS FOR HIGHWAY CONSTRUCTION, SECTION 603
“T-TOP STACKABLE
CHANNELIZER”
(OVERSIZED TRAFFIC CONE)
42” HIGH DENSITY POLYETHYLENE
PLASTIC REFLECTORIZED WITH TYPE
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
ALTERNATING STRIPES 6” WIDE, AND
SEPARATE BASE
BENT
MANUFACTURING
COMPANY
APPROVED NCHRP REPORT 350, (23-NOV-98), (WZ-6)
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (23-
NOV-98)
“TDS42 TEAR DROP STACKABLE
42” LOW OR HIGH DENSITY
POLYETHYLENE PLASTIC
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
APPROVED NCHRP REPORT 350, (15-SEP-00), (WZ-54)
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (28-
DEC-09)
“GRIP N GO TRAILBLAZER
CHANNELIZER””
MFR NO. 03-750-6HI
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
CORTINA SAFETY
PRODUCTS GROUP
SELF-CERTIFICATION, (31 DEC-14)
“RT-7000 SERIES”
42” POLYETHYLENE PLASTIC
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
EASTERN METAL / USA
SIGN
SELF-CERTIFICATION, (19-APR-06)
OVERSIZED CONES (Continued)
“HIGHWAY TECH 42” TRIMLINE
42” LOW DENSITY POLYETHYLENE
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
ALTERNATING STRIPES 6” WIDE, AND
SEPARATE 16 POUND OR 30 POUND
BASE
SELF-CERTIFICATION, (16-AUG-04)
“GRIP AND GO CHANNELIZER”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (12-FEB-09)
“THE DIVERTOR”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (19-DEC-01)
“42” CHANNELIZER CONE”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (26-SEP-12)
“NAVIGATOR CHANNELIZER”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
PLASTIC SAFETY
SYSTEMS
SELF-CERTIFICATION, (06-OCT-98)
“42” NAVICADE”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
PLASTICADE
PRODUCTS
SELF-CERTIFICATION, (03-MAR-09)
“42” CHANNELIZER”
42” LINEAR LOW DENSITY
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SERVICES, INC.
SELF-CERTIFICATION, (02-JUN-03)
“RINGTOP TD7300 SERIES”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
THREE D TRAFFIC
WORKS, INC.
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (24-
APR-02)
“RINGTOP TD7500 SERIES”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (18-
JAN-07)
“THE GRABBER”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
TRAFFIX DEVICES, INC.
APPROVED NCHRP REPORT 350, (28-DEC-99), (WZ-24)
DEC-99)
“THE LOOPER”
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
APPROVED NCHRP REPORT 350, (08-FEB-05), (WZ-189)
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (DATE
OF RECEIPT - 12-MAR-15)
“THE TRAFFIC LOGIX
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
TRAFFIC LOGIX INC.
SELF-CERTIFICATION, (01-JUL-04)
(Category I Continued)
PORTABLE PLASTIC DRUMS
SEE 2007 STANDARD SPECIFICATIONS FOR HIGHWAY CONSTRUCTION, SECTION 603
“42” CHANNELIZER”
42” LINEAR LOW DENSITY
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (02-JUN-03)
“TRAILBOSS” MODEL 1600
PORTABLE PLASTIC DRUM
SINGLE PIECE LOW DENSITY
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (12-
MAR-04)
“TRAILBOSS” MODEL 1610
SINGLE PIECE HIGH DENSITY
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
MAR-04)
“SUPERDOME” PORTABLE
PLASTIC DRUM
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
PORTABLE PLASTIC DRUMS (Continued)
“SUPERDOME TIRE RING”
SINGLE PIECE LOW OR HIGH DENSITY
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
TIRE RING BALLAST BASE
“SUPERDOME” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
“CHANNELIZER DRUM”
MFR NO. 03-780-6HI
HIGH DENSITY POLYETHYLENE
III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
CORTINA SAFETY
PRODUCTS GROUP
DEC-14)
“HIGHWAY TECH CHANNELIZING
DRUM” PORTABLE PLASTIC DRUM
MODEL HTHD-6HI
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (20-
JUN-02)
“HIGHWAY TECH CHANNELIZING
DRUM” PORTABLE PLASTIC DRUM
MODEL HTLD-6HI
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION PER FHWA APPROVAL LETTER, (20-
JUN-02)
“THE DIRECTOR” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIIFICATION, (12-19-02)
“SC-HD-46HIP”
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (26-SEP-12)
“LIFEGARD” PORTABLE PLASTIC
DRUM
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SYSTEMS, INC.
SELF-CERTIFICATION, (06-OCT-98)
“LIFEGARD II” PORTABLE PLASTIC
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (17-JUN-02)
“ECONOCADE” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (19-MAY-09)
“ECONOCADE II” PORTABLE
SINGLE PIECE LOW DENSITY OR HIGH
DENSITY POLYETHYLENE PLASTIC
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (06-OCT-10)
“RHINO CHANNELIZER DRUM”
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (13-MAR-02)
“RHINO CHANNELIZER DRUM”
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (13-MAR-02)
“MODEL 1510 CHANNELIZER”
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (03-APR-00)
“MODEL 1500 CHANNELIZER”
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (03-APR-00)
CHANNELIZING DRUM” HDPE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (17-MAR-04)
CHANNELIZING DRUM” LDPE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
SELF-CERTIFICATION, (17-MAR-04)
“TRAFFIX GENERATION IV -
MODEL #18000” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
“TRAFFIX GENERATION IV -
MODEL #18000” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
“TRAFFIX TIRE RING” PORTABLE
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
“B 200” PORTABLE PLASTIC DRUM
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
APPROVED NCHRP REPORT 350, (29-DEC-99), (WZ-26)
“B 400” PORTABLE PLASTIC DRUM
REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
APPROVED NCHRP REPORT 350, (29-DEC-99), (WZ-26)
“B 400A” PORTABLE PLASTIC
TWO PIECE LOW DENSITY
POLYETHYLENE PLASTIC DRUM WITH A
MAIN DRUM BODY AND A SEPARATE
BASE REFLECTORIZED WITH TYPE III
FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
ALTERNATING STRIPES 6” WIDE.
THIS DRUM MAY ALSO UTILIZE A 25, 35
OR 40 LBS. RUBBER BASE.
SELF-CERTIFICATION, (03-AUG-10)
“B 500 LC” PORTABLE PLASTIC
TWO PIECE POLYETHYLENE PLASTIC
DRUM WITH A MAIN DRUM BODY AND A
SEPARATE BASE REFLECTORIZED
WITH TYPE III FLEXIBLE PRISMATIC
RETROREFLECTIVE SHEETING, TWO
ORANGE AND TWO WHITE
ALTERNATING STRIPES 6” WIDE.
THIS DRUM MAY ALSO BE
SUPPLEMENTED WITH A 25 OR 40 LBS.
RUBBER TIRE RING BASE.
SELF-CERTIFICATION, (28-JUN-10)
(Category I Continued)
FLEXIBLE DELINEATOR POSTS
--SCDOT--
SEE “QUALIFIED PRODUCTS POLICY FOR FLEXIBLE DELINEATOR POSTS”, LATEST EDITION
FOR PRODUCT LISTING, SEE QUALIFIED PRODUCTS LISTING 50, AVAILABLE FROM THE RESEARCH AND MATERIALS ENGINEER
TEMPORARY SURFACE MOUNTED FLEXIBLE DELINEATOR POSTS
--ALL--
SEE “QUALIFIED PRODUCTS POLICY FOR FLEXIBLE DELINEATOR POSTS”, LATEST EDITION
FOR PRODUCT LISTING, SEE QUALIFIED PRODUCT LISTING 50, AVAILABLE FROM THE RESEARCH AND MATERIALS ENGINEER
--CONTRACT--
RESTRICTIONS -
FOR WORK ZONES, ALL FLEXIBLE DELINEATOR POSTS SHALL BE SURFACE MOUNTED. THE COLOR OF THE POSTS AND THE REFLECTIVE SHEETING SHALL BE THE SAME AS THE
COLOR OF THE ADJACENT EDGE LINE OR CENTER LINE.
APPROVED WORK ZONE TRAFFIC CONTROL DEVICES
CATEGORY II
iCONE
ICONE INTELLIGENT TRAFFIC
BEACON
PORTABLE PLASTIC DRUM WITH A 50
POUND SAND FILLED BASE AND
INTELLIGENT TRANSPORTATION
SYSTEM HARDWARE FOR MONITORING
TRAFFIC CONDITIONS IN WORK ZONES
TELEMATICS
SERVICES LLC
TRAFFIX DEVICES
APPROVED NCHRP REPORT 350 DESIGN, (08-MAY-08), (WZ-
272)
(Category II Continued)
TYPE II BARRICADES
SEE 2007 STANDARD SPECIFICATIONS FOR HIGHWAY CONSTRUCTION, SECTION 604
TYPE II PLYWOOD PANEL
BARRICADE WITH TWO 8” PANELS
3’ BARRICADE WITH PLYWOOD
PANELS, 1/2” X 8” X 36” ON TOP AND
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ANGLE IRON OR STEEL ROLL
FORMED LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
SHEETING FOR REFLECTORIZATION OF
THIS BARRICADE.
COMPANY
B. C. CANNON
COMPANY, INC.
SCDOT
GUARDWAY
CORPORATION
STAY ALERT SAFETY
TRI-STATE TRAFFIC SAFETY, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN
BY BENT MANUFACTURING COMPANY, (02-MAY-00)
B. C. CANNON COMPANY, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN
BY BENT MANUFACTURING COMPANY, (15-MAY-00)
SCDOT -- APPROVED NCHRP REPORT 350 PER FHWA
APPROVAL (23-NOV-98) OF DESIGN BY BENT
MANUFACTURING COMPANY, (13-MAY-02)
GUARDWAY CORPORATION -- APPROVED NCHRP REPORT
350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN BY BENT
MANUFACTURING COMPANY, (02-MAR-04)
STAY ALERT SAFETY SERVICES, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN
BY BENT MANUFACTURING COMPANY PURCHASE FROM
GUARDWAY CORPORATION, (04-MAR-04)
(Category II Continued) TYPE II BARRICADES (Continued)
TYPE II PLYWOOD PANEL
BARRICADE WITH A 12/8 PANEL
DESIGN
PANELS, 1/2” X 12” X 36” ON TOP AND
1/2” X 8” X 36” ON BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ANGLE IRON OR STEEL ROLL
FORMED LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
COMPANY
B. C. CANNON
COMPANY, INC.
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN
BY BENT MANUFACTURING COMPANY, (02-MAY-00)
B. C. CANNON COMPANY, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN
BY BENT MANUFACTURING COMPANY, (15-MAY-00)
SCDOT -- APPROVED NCHRP REPORT 350 PER FHWA
APPROVAL (23-NOV-98) OF DESIGN BY BENT
MANUFACTURING COMPANY, (13-MAY-02)
“UNIVERSAL PLASTIC” TYPE II
BARRICADE WITH 8” PANEL
AREAS
2’ BARRICADE CONSTRUCTED OF A
WHITE HIGH DENSITY POLYETHYLENE
MATERIAL WITH AN 8” X 24” PANEL
AREA ON TOP AND BOTTOM
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“UNIVERSAL PLASTIC” TYPE II
2’ BARRICADE CONSTRUCTED OF A
WHITE HIGH DENSITY POLYETHYLENE
MATERIAL WITH A 12” X 24” TOP PANEL
AREA AND AN 8” X 24” BOTTOM PANEL
AREA REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, ON EACH PANEL AREA
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“WAFFLE BOARD PLASTIC PANEL”
TYPE II BARRICADE WITH TWO 8”
PANELS
2’ BARRICADE WITH WAFFLE BOARD
PLASTIC PANELS CONSTRUCTED OF A
HIGH DENSITY HOMOPOLYMER
POLYETHYLENE MATERIAL, ½” X 8” X
24” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ANGLE IRON OR STEEL ROLL
FORMED LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“WAFFLE BOARD PLASTIC PANEL”
TYPE II BARRICADE WITH A 12/8
PANEL DESIGN
2’ BARRICADE WITH WAFFLE BOARD
PLASTIC PANELS CONSTRUCTED OF A
HIGH DENSITY HOMOPOLYMER
POLYETHYLENE MATERIAL, ½” X 12” X
24” ON TOP AND ½” X 8” X 24” ON
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ANGLE IRON OR STEEL ROLL
FORMED LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“JAMMER WBT2” TYPE II PLASTIC
PANEL BARRICADE WITH TWO 8”
PANEL AREAS AND PLASTIC LEGS
2’ BARRICADE WITH PLASTIC PANELS,
EITHER 1/2" X 8” X 24” OR 1” X 8” X 24”,
ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR
POLYETHYLENE PLASTIC LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
KORMAN SIGNS, INC.
APPROVED NCHRP REPORT 350, (24-NOV-04), (WZ-100
AMENDMENT #5)
PANEL AREAS AND STEEL LEGS
EITHER 1” X 8” X 24”, 3/8" X 8” X 24”, OR
1/2" X 8” X 24”, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR 16
GAUGE GALVANIZED STEEL TUBING
LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL BARRICADE WITH A 12”/8”
PANEL DESIGN AND PLASTIC
LEGS
A 1/2" X 12” X 24” ON TOP AND A 1/2” X
8” X 24” ON BOTTOM, REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON
FOUR POLYETHYLENE PLASTIC LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL DESIGN AND STEEL LEGS
EITHER A 3/8" X 12” X 24” ON TOP AND A
3/8” X 8” X 24” ON BOTTOM OR A 1/2" X
12” X 24” ON TOP AND A 1/2” X 8” X 24”
ON BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR 16
GAUGE GALVANIZED STEEL TUBING
LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL AREAS AND PLASTIC LEGS
3’ BARRICADE WITH PLASTIC PANELS,
1" X 8” X 36”, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR
POLYETHYLENE PLASTIC LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL AREAS AND STEEL LEGS
EITHER 3/8” X 8” X 36”, 1/2” X 8” X 36, OR
1" X 8” X 36”, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR 16
GAUGE GALVANIZED STEEL TUBING
LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL DESIGN AND PLASTIC
LEGS
A 1/2" X 12” X 36” ON TOP AND A 1/2” X
8” X 36” ON BOTTOM, REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON
FOUR POLYETHYLENE PLASTIC LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PANEL DESIGN AND STEEL LEGS
EITHER A 3/8" X 12” X 36” ON TOP AND A
3/8” X 8” X 36” ON BOTTOM OR A 1/2" X
12” X 36” ON TOP AND A 1/2” X 8” X 36”
ON BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON FOUR 16
GAUGE GALVANIZED STEEL TUBING
LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“FIBERCADE” TYPE II PLASTIC
PANEL AREAS
2’ BARRICADE WITH HIGH MOLECULAR
WEIGHT POLYETHYLENE PANELS, 8” X
24” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (28-MAY-99), (WZ-14)
“FIBERCADE” TYPE II PLASTIC
PANEL BARRICADE WITH A 12/8
2’ BARRICADE WITH HIGH MOLECULAR
WEIGHT POLYETHYLENE PANELS, 12” X
24” ON TOP AND 8” X 24” ON BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (28-MAY-99), (WZ-14)
“TYPE 1C CONSTRUCTION
BARRICADE” TYPE II PLASTIC
3’ BARRICADE WITH POLYPROPYLENE
PANELS, 8” X 36” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1-
1/4” X 1-1/4” X 1/8” X 47” METAL LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (24-MAY-00), (WZ-36)
“TYPE 1C CONSTRUCTION
PANELS, 12” X 36” ON TOP AND 8” X 36”
ON BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1-
1/4” X 1-1/4” X 1/8” X 47” METAL LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TYPE 1D CONSTRUCTION
PANELS, 8” X 36” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 5/8”
X 1-1/2” X 47” PLASTIC LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TYPE 1D CONSTRUCTION
PANELS, 12” X 36” ON TOP AND 8” X 36”
ON BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 5/8”
X 1-1/2” X 47” PLASTIC LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TYPE 2A CONSTRUCTION
2’ BARRICADE WITH POLYPROPYLENE
PANELS, 8” X 24” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1-
1/4” X 1-1/4” X 1/8” X 47” METAL LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“CONSTRUCTION BARRICADE”
TYPE II PLASTIC PANEL
DESIGN WITH STEEL LEGS
PANELS, 12” X 24” ON TOP AND 8” X 24
ON BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1-
1/4” X 1-1/4” X 1/8” X 47” METAL LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TYPE 2B CONSTRUCTION
PANELS, 8” X 24” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 5/8”
X 1-1/2” X 47” PLASTIC LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“CONSTRUCTION BARRICADE”
DESIGN WITH PLASTIC LEGS
PANELS, 12” X 24” ON TOP AND 8” X 24”
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 5/8”
X 1-1/2” X 47” PLASTIC LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“SERIES 2100” TYPE II PLASTIC
12” X 24” ON TOP AND 8” X 24” ON
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON 45-1/2”
PLASTIC LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (24-MAY-00), (WZ-33)
“TD2150 WORKS BARRICADE”
TYPE II PLASTIC BARRICADE
WITH A 12/8 PANEL DESIGN
12” X 24 ½” ON TOP AND 8” X 24 ½” ON
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PLASTIC
LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (17-MAY-05), (WZ-198)
“SERIES 2200” TYPE II PLASTIC
12” X 24” ON TOP AND 8” X 24” ON
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ROLL FORMED LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TD2250 MODEL” TYPE II PLASTIC
PANEL BARRICADE WITH A 8/8
PANEL DESIGN
(24” WIDE)
(32” WIDE)
2’ AND 2 1/2’ BARRICADES WITH
PLASTIC PANELS, 8” X 24” OR 8” X 32”
ON TOP AND BOTTOM, RESPECTIVELY,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ROLL FORMED LEGS
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“TD2250 MODEL” TYPE II PLASTIC
PANEL BARRICADE WITH A 8/8
(36” WIDE)
8” X 36” ON TOP AND BOTTOM
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ROLL FORMED LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“SERIES 2300” TYPE II PLYWOOD
1/2” X 8” X 36” ON BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 OR 14 GAUGE
STEEL ROLL FORMED LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (24-MAY-00), (WZ-33)
“ECONOMY PLASTIC FOLDING”
BARRICADE WITH TWO 8” PANELS
8” X 24” ON TOP AND BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“A-FRAME BARRICADE” TYPE II
PLYWOOD PANEL BARRICADE
WITH A 12/8 PANEL DESIGN
BOTTOM, REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 GAUGE STEEL
ANGLE LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
UNITED RENTALS
HIGHWAY
TECHNOLOGIES, INC.
APPROVED NCHRP REPORT 350, (6-MAY-00), (WZ-41)
APPROVED NCHRP REPORT 350, (20-JUN-03), (WZ-41-
AMENDMENT #1)
PLYWOOD PANEL BARRICADE
WITH TWO 8” PANEL AREAS
1/2” X 8” X 36” ON BOTTOM,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 GAUGE STEEL
ANGLE LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PLASTIC PANEL BARRICADE WITH
A 12/8 PANEL DESIGN
3’ BARRICADE WITH 12” X 36” PANEL ON
TOP AND 8” X 36” PANEL ON BOTTOM,
FABRICATED FROM 0.350 INCH THICK
HIGH DENSITY POLYETHYLENE,
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON PAINTED
OR GALVANIZED 45” 12 GAUGE STEEL
ANGLE LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
PLASTIC PANEL BARRICADE WITH
TWO 8” PANEL AREAS
3’ BARRICADE WITH 8” X 36” PANELS
ON TOP AND BOTTOM, FABRICATED
FROM 0.350 INCH THICK HIGH DENSITY
POLYETHYLENE, REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON
PAINTED OR GALVANIZED 45” 12
GAUGE STEEL ANGLE LEGS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
“STEELCADE TYPE II” TYPE II
STEEL-LEGGED BARRICADES
WITH WAFFLEBOARD PANELS
2’ BARRICADES WITH 8” X 24” PANELS
ON TOP AND BOTTOM, FABRICATED
FROM HIGH IMPACT POLYOLEFIN
STRUCTURAL RESIN, REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON HIGH
STRENGTH COLD ROLLED STEEL
ANGLE IRON
SPECIAL NOTE
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
CORTENA SAFETY
APPROVED NCHRP REPORT 350, (7-OCT-03), (WZ-165)
(Category II Continued)
TYPE III BARRICADES
SEE 2007 STANDARD SPECIFICATIONS FOR HIGHWAY CONSTRUCTION, SECTION 604
PORTABLE TYPE III PLYWOOD
PANEL BARRICADE
6’ BARRICADE WITH 1” X 8” X 72”
PLYWOOD PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1-1/2” X 1-1/2” X 3/16” X 63” ANGLE
STEEL UPRIGHTS ATTACHED TO TWO
1-1/2” X 1-1/2” X 3/16” X 60” ANGLE
STEEL BASE STANDS WITH 2” X 2” X 8”
SQUARE STEEL TUBING RECEIVERS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
B. C. CANNON
COMPANY, INC.
SCDOT
GUARDWAY
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF
DESIGN BY BENT MANUFACTURING COMPANY, (02-MAY-
00)
B. C. CANNON COMPANY, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (23-NOV-98) OF
DESIGN BY BENT MANUFACTURING COMPANY, (15-MAY-
00)
SCDOT -- APPROVED NCHRP REPORT 350 PER FHWA
APPROVAL (23-NOV-98) OF DESIGN BY BENT
MANUFACTURING COMPANY, (13-MAY-02)
GUARDWAY CORPORATION -- APPROVED NCHRP REPORT
350 PER FHWA APPROVAL (23-NOV-98) OF DESIGN BY
BENT MANUFACTURING COMPANY, (09-JUN-06)
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
ATTACHING ANY OTHER TYPE OF RIGID SIGN SUBSTRATE
TO A TYPE III BARRICADE IS PROHIBITED.
TYPE III BARRICADES (Continued)
8’ BARRICADE WITH 3/4” X 8” X 96”
PLYWOOD PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1-3/4” X 1-3/4” X 60” 12 GAUGE
PERFORATED STEEL TUBING
UPRIGHTS INSERTED INTO TWO 2” X 2”
X 6” STEEL TUBE RECEIVERS
ATTACHED TO TWO 2” X 2” ANGLE
STEEL BASE SUPPORTS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
STAY ALERT SAFETY
APPROVED NCHRP REPORT 350, (03-JUN-02), (WZ-120)
STAY ALERT SAFETY SERVICES, INC. -- APPROVED NCHRP
REPORT 350 PER FHWA APPROVAL (03-JUN-02) OF DESIGN
BY NES WORK SAFE, (04-MAR-04)
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
4’ – 8’ BARRICADE WITH 1” X 8” X 48” –
96” PLYWOOD PANELS
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1-
1/2” X 1-1/2” X 3/16” X 63” ANGLE STEEL
UPRIGHTS ATTACHED TO TWO 1-1/2” X
1-1/2” X 3/16” X 60” ANGLE STEEL BASE
STANDS WITH 2” X 2” X 8” SQUARE
STEEL TUBING RECEIVERS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
BENT MANUFACTURING
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“T3B” TYPE III PLASTIC PANEL
BARRICADE
4’ - 12’ BARRICADE WITH 1” X 8” X 48” -
144” HOLLOW PLASTIC PANELS
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON 1-3/4” X
1-3/4” X 60” - 72” SQUARE PLASTIC
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” - 72” PERFORATED SQUARE STEEL
TUBING FEET WITH 2” X 2” X 6”
PERFORATED SQUARE STEEL TUBING
UPRIGHT RECEIVERS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
DAVIDSON PLASTICS
APPROVED NCHRP REPORT 350, (29-JUN-00), (WZ-39)
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“IRS TYPE III” PLASTIC
4’-12’ BARRICADE WITH 1” X 8” X 48” –
144” HOLLOW PLASTIC PANELS
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON 1-3/4” X
1-3/4” X 60” – 72” SQUARE PLASTIC
UPRIGHTS ATTACHED TO TWO
PORTABLE 14” X 34” RECYCLED
RUBBER BASES WITH A PATENTED
QUICK RELEASE SYSTEM
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
IMPACT RECOVERY
APPROVED NCHRP REPORT 350, (22-MAR-02), (WZ-110)
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“KSIBTIII-SW” TYPE III PLYWOOD
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1
¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY TWO 2” X 2” X 6”
RECEIVERS
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (15-NOV-01), (WZ-85); (20-
JUN-02), (WZ-100)
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“KSIBTIII-133Z” TYPE III PLYWOOD
REFLECTORIZED WITH
RETROREFLECTIVE SHEETING AS
NOTED BELOW, MOUNTED ON TWO 1
¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY TWO TL133-Z SHEAR
PIN ASSEMBLIES FABRICATED BY
XCESSORIES SQUARED
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (08-SEP-00), (WZ-51); (20-
JUN-02), (WZ-100)
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“WBT3-BR” TYPE III HOLLOW
PLASTIC OR ALPOLIC PANEL
4’ – 12’ BARRICADE WITH EITHER
HOLLOW EXTRUDED PLASTIC OR
ALPOLIC PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1 ¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY SPLICE PLATE
BRACKETS WITH NO HORIZONTAL
CROSS BRACE
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
APPROVED NCHRP REPORT 350, (10-JUL-03), (WZ-100
AMENDMENT #3)
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“WBT3-BRH” TYPE III HOLLOW
ALPOLIC PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1 ¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY SPLICE PLATE
BRACKETS WITH HORIZONTAL CROSS
BRACE
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“WBT3-SW” TYPE III HOLLOW
ALPOLIC PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1 ¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY WELDED STUB
RECEIVERS WITH NO HORIZONTAL
CROSS BRACE
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS ALTERNATES TO TYPE III
HIGH INTENSITY RETROREFLECTIVE
RESTRICTIONS -- SUPPLEMENTARY SIGNS ATTACHED
TO TYPE III BARRICADES SHALL BE CONSTRUCTED WITH
AN APPROVED REFLECTIVE FABRIC SIGN SUBSTRATE OR
AN APPROVED ALUMINUM LAMINATE SUBSTRATE. THE
APPROVED ALUMINUM LAMINATE SUBSTRATES SHALL BE
EITHER ACOPAN, ALPOLIC, DIBOND OR REYNOLITE.
“WBT3-SWH” TYPE III HOLLOW
ALPOLIC PANELS REFLECTORIZED
WITH RETROREFLECTIVE SHEETING
AS NOTED BELOW, MOUNTED ON TWO
1 ¾” X 1 ¾” X 58” 12 GAUGE GALVNIZED
PERFORATED SQUARE STEEL TUBING
UPRIGHTS ATTACHED TO TWO 2” X 2” X
60” 12 GAUGE GALVANIZED
PERFORATED SQUARE STEEL TUBING
BASE STANDS BY WELDED STUB
RECEIVERS WITH HORIZONTAL CROSS
BRACE
SPECIAL NOTE 1
for CONTRACT WORK:
REFLECTORIZE ALL BARRICADES WITH
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING ON ALL
PROJECTS LET TO CONTRACT AFTER
MAY I, 2012.
SPECIAL NOTE 2
for SCDOT MAINTENANCE
FORCES:
TYPE VIII OR TYPE IX PRISMATIC
RETROREFLECTIVE SHEETING MAY BE
USED AS…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .