260923 lighting control devices.pdf

F5W61607 Combined Support Maintenance Shop - Phase II Ohio Army National Guard Rev. 0 Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 1

SECTION 260923 - LIGHTING CONTROL DEVICES

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following lighting control devices:

1. Time switches.

2. Outdoor photoelectric switches.

3. Indoor occupancy sensors.

4. Lighting contactors.

B. Related Sections include the following:

1. Division 26 Section "Wiring Devices" for wall-box dimmers, wall-switch occupancy sensors, and manual light switches.

1.3 DEFINITIONS

A. LED: Light-emitting diode.

B. PIR: Passive infrared.

1.4 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Shop Drawings: Show installation details for occupancy and light-level sensors.

1. Interconnection diagrams showing field-installed wiring.

C. Field quality-control test reports.

D. Operation and Maintenance Data: For each type of product to include in emergency, operation, and maintenance manuals.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 2

1.5 QUALITY ASSURANCE

A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use.

1.6 COORDINATION

A. Coordinate layout and installation of ceiling-mounted devices with other construction that penetrates ceilings or is supported by them, including light fixtures, HVAC equipment, smoke detectors, fire-suppression system, and partition assemblies.

PART 2 - PRODUCTS

2.1 TIME SWITCHES

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Area Lighting Research, Inc.; Tyco Electronics.

2. Grasslin Controls Corporation; a GE Industrial Systems Company.

3. Intermatic, Inc.

4. Leviton Mfg. Company Inc.

5. Lightolier Controls; a Genlyte Company.

6. Lithonia Lighting; Acuity Lighting Group, Inc.

7. Paragon Electric Co.; Invensys Climate Controls.

8. Square D; Schneider Electric.

9. TORK.

10. Touch-Plate, Inc.

11. Watt Stopper (The).

B. Electromechanical-Dial Time Switches: Type complying with UL 917.

1. Contact Configuration: SPST.

2. Contact Rating: 30-A inductive or resistive, 240-V ac.

3. Circuitry: Allow connection of a photoelectric relay as substitute for on-off function of a program.

4. Astronomic time dial.

5. Eight-Day Program: Uniquely programmable for each weekday and holidays.

6. Skip-a-day mode.

7. Wound-spring reserve carryover mechanism to keep time during power failures, minimum of 16 hours.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 3

2.2 OUTDOOR PHOTOELECTRIC SWITCHES

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Area Lighting Research, Inc.; Tyco Electronics.

2. Grasslin Controls Corporation; a GE Industrial Systems Company.

3. Intermatic, Inc.

4. Lithonia Lighting; Acuity Lighting Group, Inc.

5. Novitas, Inc.

6. Paragon Electric Co.; Invensys Climate Controls.

7. Square D; Schneider Electric.

8. TORK.

9. Touch-Plate, Inc.

10. Watt Stopper (The).

B. Description: Solid state, with SPST dry contacts rated for 1800-VA tungsten or 1000- VA inductive , to operate connected relay, contactor coils, or microprocessor input;

complying with UL 773A.

1. Light-Level Monitoring Range: 1.5 to 10 fc, with an adjustment for turn-on and turn-off levels within that range, and a directional lens in front of photocell to prevent fixed light sources from causing turn-off.

2. Time Delay: 15-second minimum, to prevent false operation.

3. Surge Protection: Metal-oxide varistor, complying with IEEE C62.41.1, IEEE C62.41.2, and IEEE 62.45 for Category A1 locations.

4. Mounting: Twist lock complying with IEEE C136.10, with base-and-stem mounting or stem-and-swivel mounting accessories as required to direct sensor to the north sky exposure.

2.3 INDOOR PHOTOELECTRIC SWITCHES

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Allen-Bradley/Rockwell Automation.

2. Area Lighting Research, Inc.; Tyco Electronics.

3. Eaton Electrical Inc; Cutler-Hammer Products.

4. Grasslin Controls Corporation; a GE Industrial Systems Company.

5. Intermatic, Inc.

6. Lithonia Lighting; Acuity Lighting Group, Inc.

7. MicroLite Lighting Control Systems.

8. Novitas, Inc.

9. Paragon Electric Co.; Invensys Climate Controls.

10. Square D; Schneider Electric.

11. TORK.

12. Touch-Plate, Inc.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 4

13. Watt Stopper (The).

B. Ceiling-Mounted Photoelectric Switch: Solid-state, light-level sensor unit, with separate relay unit, to detect changes in lighting levels that are perceived by the eye.

Cadmium sulfide photoresistors are not acceptable.

1. Sensor Output: Contacts rated to operate the associated relay, complying with UL 773A. Sensor shall be powered from the relay unit.

2. Relay Unit: Dry contacts rated for 20-A ballast load at 120- and 277-V ac, for 13-A tungsten at 120-V ac, and for 1 hp at 120-V ac. Power supply to sensor shall be 24-V dc, 150-mA, Class 2 power source as defined by NFPA 70.

3. Light-Level Monitoring Range: 10 to 200 fc , with an adjustment for turn-on and turn-off levels within that range.

4. Time Delay: Adjustable from 5 to 300 seconds to prevent cycling, with deadband adjustment.

5. Indicator: Two LEDs to indicate the beginning of on-off cycles.

2.4 INDOOR OCCUPANCY SENSORS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Hubbell Lighting.

2. Leviton Mfg. Company Inc.

3. Lithonia Lighting; Acuity Lighting Group, Inc.

4. Novitas, Inc.

5. RAB Lighting, Inc.

6. Sensor Switch, Inc.

7. TORK.

8. Watt Stopper (The).

B. General Description: Wall- or ceiling-mounting, solid-state units with a separate relay unit.

1. Operation: Unless otherwise indicated, turn lights on when covered area is occupied and off when unoccupied; with a time delay for turning lights off, adjustable over a minimum range of 1 to 15 minutes.

2. Sensor Output: Contacts rated to operate the connected relay, complying with UL 773A. Sensor shall be powered from the relay unit.

3. Relay Unit: Dry contacts rated for 20-A ballast load at 120- and 277-V ac, for 13-A tungsten at 120-V ac, and for 1 hp at 120-V ac. Power supply to sensor shall be 24-V dc, 150-mA, Class 2 power source as defined by NFPA 70.

4. Mounting:

a. Sensor: Suitable for mounting in any position on a standard outlet box.

b. Relay: Externally mounted through a 1/2-inch knockout in a standard electrical enclosure.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 5

c. Time-Delay and Sensitivity Adjustments: Recessed and concealed behind hinged door.

5. Indicator: LED, to show when motion is being detected during testing and normal operation of the sensor.

6. Bypass Switch: Override the on function in case of sensor failure.

7. Automatic Light-Level Sensor: Adjustable from 2 to 200 fc; keep lighting off when selected lighting level is present.

C. Dual-Technology Type: Ceiling mounting; detect occupancy by using a combination of PIR and ultrasonic detection methods in area of coverage. Particular technology or combination of technologies that controls on-off functions shall be selectable in the field by operating controls on unit.

1. Sensitivity Adjustment: Separate for each sensing technology.

2. Detector Sensitivity: Detect occurrences of 6-inch-minimum movement of any portion of a human body that presents a target of not less than 36 sq. in., and detect a person of average size and weight moving not less than 12 inches in either a horizontal or a vertical manner at an approximate speed of 12 inches/s.

3. Detection Coverage (Standard Room): Detect occupancy anywhere within a circular area of 1000 sq. ft. when mounted on a 96-inch-high ceiling.

2.5 LIGHTING CONTACTORS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

1. Allen-Bradley/Rockwell Automation.

2. ASCO Power Technologies, LP; a division of Emerson Electric Co.

3. Eaton Electrical Inc.; Cutler-Hammer Products.

4. GE Industrial Systems; Total Lighting Control.

5. Grasslin Controls Corporation; a GE Industrial Systems Company.

6. Hubbell Lighting.

7. Lithonia Lighting; Acuity Lighting Group, Inc.

8. MicroLite Lighting Control Systems.

9. Square D; Schneider Electric.

10. TORK.

11. Touch-Plate, Inc.

12. Watt Stopper (The).

B. Description: Electrically operated and mechanically held, combination type, complying with NEMA ICS 2 and UL 508.

1. Current Rating for Switching: Listing or rating consistent with type of load served, including tungsten filament, inductive, and high-inrush ballast (ballast with 15 percent or less total harmonic distortion of normal load current).

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 6

2. Fault Current Withstand Rating: Equal to or exceeding the available fault current at the point of installation.

3. Enclosure: Comply with NEMA 250.

4. Provide with control and pilot devices as indicated on Drawings, matching the

NEMA type specified for the enclosure.

C. BAS Interface: Provide hardware interface to enable the BAS to monitor and control lighting contactors.

1. Monitoring: On-off status, selective lighting and mechanical HVAC equipment will be monitored as in Specification Section 15940.

2. Control: On-off operation, selective lighting and mechanical HVAC equipment will be controlled as defined in Specification Section 15940.

2.6 CONDUCTORS AND CABLES

A. Power Wiring to Supply Side of Remote-Control Power Sources: Not smaller than No. 12 AWG. Comply with requirements in Division 26 Section "Low-Voltage Electrical Power Conductors and Cables."

B. Classes 2 and 3 Control Cable: Multiconductor cable with stranded-copper conductors not smaller than No. 18 AWG. Comply with requirements in Division 26 Section "Low-Voltage Electrical Power Conductors and Cables."

C. Class 1 Control Cable: Multiconductor cable with stranded-copper conductors not smaller than No. 14 AWG. Comply with requirements in Division 26 Section "Low- Voltage Electrical Power Conductors and Cables."

PART 3 - EXECUTION

3.1 SENSOR INSTALLATION

A. Install and aim sensors in locations to achieve not less than 90 percent coverage of areas indicated. Do not exceed coverage limits specified in manufacturer's written instructions.

3.2 CONTACTOR INSTALLATION

A. Mount electrically held lighting contactors with elastomeric isolator pads, to eliminate structure-borne vibration, unless contactors are installed in an enclosure with factory-installed vibration isolators.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 7

3.3 WIRING INSTALLATION

A. Wiring Method: Comply with Division 26 Section "Low-Voltage Electrical Power Conductors and Cables." Minimum conduit size shall be 1/2 inch.

B. Wiring within Enclosures: Comply with NECA 1. Separate power-limited and nonpower-limited conductors according to conductor manufacturer's written instructions.

C. Size conductors according to lighting control device manufacturer's written instructions, unless otherwise indicated.

D. Splices, Taps, and Terminations: Make connections only on numbered terminal strips in junction, pull, and outlet boxes; terminal cabinets; and equipment enclosures.

3.4 IDENTIFICATION

A. Identify components and power and control wiring according to Division 26 Section "Identification for Electrical Systems."

1. Identify controlled circuits in lighting contactors.

2. Identify circuits or luminaries controlled by photoelectric and occupancy sensors at each sensor.

B. Label time switches and contactors with a unique designation.

3.5 FIELD QUALITY CONTROL

A. Perform the following field tests and inspections and prepare test reports:

1. After installing time switches and sensors, and after electrical circuitry has been energized, adjust and test for compliance with requirements.

2. Operational Test: Verify operation of each lighting control device, and adjust time delays.

B. Lighting control devices that fail tests and inspections are defective work.

3.6 ADJUSTING

A. Occupancy Adjustments: When requested within 12 months of date of Substantial Completion, provide on-site assistance in adjusting sensors to suit occupied conditions. Provide up to two visits to Project during other-than-normal occupancy hours for this purpose.

Defense Supply Center Columbus, Ohio 30 January 2009 Bid Final

LIGHTING CONTROL DEVICES 260923 - 8

3.7 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain lighting control devices. Refer to Division 01 Section "Demonstration and Training."

END OF SECTION 260923