087100_Door_Hardware.pdf

DOOR HARDWARE 087100 - 1

SECTION 087100 – DOOR HARDWARE

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes commercial door hardware for the following:

1. Swinging doors.

2. Other doors to the extent indicated.

B. Door hardware includes, but is not necessarily limited to, the following:

1. Mechanical door hardware.

2. Cylinders specified for doors in other sections.

C. Related Sections:

1. Division 08 Section “Operations and Maintenance”.

2. Division 08 Section “Door Schedule”.

3. Division 08 Section “Door Hardware Schedule”.

4. Division 08 Section “Hollow Metal Doors and Frames”.

5. Division 08 Section “Flush Wood Doors”.

D. Codes and References: Comply with the version year adopted by the Authority Having

Jurisdiction.

1. ANSI A117.1 - Accessible and Usable Buildings and Facilities.

2. ICC/IBC - International Building Code.

3. NFPA 70 - National Electrical Code.

4. NFPA 80 - Fire Doors and Windows.

5. NFPA 101 - Life Safety Code.

6. NFPA 105 - Installation of Smoke Door Assemblies.

7. State Building Codes, Local Amendments.

E. Standards: All hardware specified herein shall comply with the following industry standards:

1. ANSI/BHMA Certified Product Standards - A156 Series

2. UL10C – Positive Pressure Fire Tests of Door Assemblies

DOOR HARDWARE 087100 - 2

1.3 SUBMITTALS

A. Product Data: Manufacturer's product data sheets including installation details, material descriptions, dimensions of individual components and profiles, operational descriptions and finishes.

B. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate the final Door

Hardware Schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.

1. Format: Comply with scheduling sequence and vertical format in DHI's "Sequence and

Format for the Hardware Schedule."

2. Organization: Organize the Door Hardware Schedule into door hardware sets indicating complete designations of every item required for each door or opening. Organize door hardware sets in same order as in the Door Hardware Sets at the end of Part 3. Submittals that do not follow the same format and order as the Door Hardware Sets will be rejected and subject to resubmission.

3. Content: Include the following information:

a. Type, style, function, size, label, hand, and finish of each door hardware item.

b. Manufacturer of each item.

c. Fastenings and other pertinent information.

d. Location of door hardware set, cross-referenced to Drawings, both on floor plans and in door and frame schedule.

e. Explanation of abbreviations, symbols, and codes contained in schedule.

f. Mounting locations for door hardware.

g. Door and frame sizes and materials.

h. Warranty information for each product.

4. Submittal Sequence: Submit the final Door Hardware Schedule at earliest possible date, particularly where approval of the Door Hardware Schedule must precede fabrication of other work that is critical in the Project construction schedule. Include Product Data, Samples, Shop Drawings of other work affected by door hardware, and other information essential to the coordinated review of the Door Hardware Schedule.

C. Proof of Certification: Provide copy of manufacturer(s) official certification or accreditation document indicating proof of status as a qualified installer of Windstorm assemblies.

D. Keying Schedule: After a keying meeting with the Government has taken place prepare a separate keying schedule detailing final instructions. Submit the keying schedule in electronic format. Include keying system explanation, door numbers, key set symbols, hardware set numbers and special instructions. Government must approve submitted keying schedule prior to the ordering of permanent cylinders/cores.

E. Informational Submittals:

DOOR HARDWARE 087100 - 3

1. LEED Submittals:

a. Product Data for Credit MR 4: For products having recycled content, documentation indicating percentages by weight of postconsumer and pre-consumer recycled content. Include statement indicating cost for each product having recycled content.

2. Product Test Reports: Indicating compliance with cycle testing requirements, based on evaluation of comprehensive tests performed by manufacturer and witnessed by a qualified independent testing agency.

F. Operating and Maintenance Manuals: Provide manufacturers operating and maintenance manuals for each item comprising the complete door hardware installation in quantity as required in Division 01, Closeout Submittals.

1.4 QUALITY ASSURANCE

A. Manufacturers Qualifications: Engage qualified manufacturers with a minimum 5 years of documented experience in producing hardware and equipment similar to that indicated for this

Project and that have a proven record of successful in-service performance.

B. Installer Qualifications: A minimum 3 years documented experience installing both standard and electrified door hardware similar in material, design, and extent to that indicated for this

Project and whose work has resulted in construction with a record of successful in-service performance.

C. Door Hardware Supplier Qualifications: Experienced commercial door hardware distributors with a minimum 5 years documented experience supplying both mechanical and electromechanical hardware installations comparable in material, design, and extent to that indicated for this Project. Supplier recognized as a factory direct distributor by the manufacturers of the primary materials with a warehousing facility in Project's vicinity.

Supplier to have on staff a certified Architectural Hardware Consultant (AHC) available during the course of the Work to consult with Contractor, Architect, and Government concerning both standard and electromechanical door hardware and keying.

D. Source Limitations: Obtain each type and variety of door hardware specified in this section from a single source unless otherwise indicated.

1. Electrified modifications or enhancements made to a source manufacturer's product line by a secondary or third party source will not be accepted.

E. Each unit to bear third party permanent label demonstrating compliance with the referenced standards.

F. Keying Conference: Conduct conference to comply with requirements in Division 01 Section

"Project Meetings." Keying conference to incorporate the following criteria into the final keying schedule document:

1. Function of building, purpose of each area and degree of security required.

DOOR HARDWARE 087100 - 4

2. Plans for existing and future key system expansion.

3. Requirements for key control storage and software.

4. Installation of permanent keys, cylinder cores and software.

5. Address and requirements for delivery of keys.

G. Pre-Submittal Conference: Conduct coordination conference in compliance with requirements in Division 01 Section "Project Meetings" with attendance by representatives of Supplier(s), Installer(s), and Contractor(s) to review proper methods and the procedures for receiving, handling, and installing door hardware.

1. Prior to installation of door hardware, conduct a project specific training meeting to instruct the installing contractors' personnel on the proper installation and adjustment of their respective products. Product training to be attended by installers of door hardware

(including electromechanical hardware) for aluminum, hollow metal and wood doors.

Training will include the use of installation manuals, hardware schedules, templates and physical product samples as required.

2. Inspect and discuss electrical roughing-in, power supply connections, and other preparatory work performed by other trades.

3. Review sequence of operation narratives for each unique access controlled opening.

4. Review and finalize construction schedule and verify availability of materials.

5. Review the required inspecting, testing, commissioning, and demonstration procedures

H. At completion of installation, provide written documentation that components were applied to manufacturer's instructions and recommendations and according to approved schedule.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Inventory door hardware on receipt and provide secure lock-up and shelving for door hardware delivered to Project site. Do not store electronic access control hardware, software or accessories at Project site without prior authorization.

B. Tag each item or package separately with identification related to the final Door Hardware

Schedule, and include basic installation instructions with each item or package.

C. Deliver, as applicable, permanent keys, cylinders, cores, access control credentials, software and related accessories directly to Government via registered mail or overnight package service.

Instructions for delivery to the Government shall be established at the "Keying Conference".

1.6 COORDINATION

A. Templates: Obtain and distribute to the parties involved templates for doors, frames, and other work specified to be factory prepared for installing standard and electrified hardware. Check

Shop Drawings of other work to confirm that adequate provisions are made for locating and installing hardware to comply with indicated requirements.

B. Door and Frame Preparation: Doors and corresponding frames are to be prepared, reinforced and pre-wired (if applicable) to receive the installation of the specified electrified, monitoring, signaling and access control system hardware without additional in-field modifications.

DOOR HARDWARE 087100 - 5

1.7 WARRANTY

A. General Warranty: Reference Division 01, General Requirements. Special warranties specified in this Article shall not deprive Government of other rights Government may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by Contractor under requirements of the Contract Documents.

B. Warranty Period: Written warranty, executed by manufacturer(s), agreeing to repair or replace components of standard and electrified door hardware that fails in materials or workmanship within specified warranty period after final acceptance by the Government. Failures include, but are not limited to, the following:

1. Structural failures including excessive deflection, cracking, or breakage.

2. Faulty operation of the hardware.

3. Deterioration of metals, metal finishes, and other materials beyond normal weathering.

4. Electrical component defects and failures within the systems operation.

C. Standard Warranty Period: One year from date of Substantial Completion, unless otherwise indicated.

D. Special Warranty Periods:

1. Ten years for mortise locks and latches.

2. Five years for exit hardware.

3. Twenty five years for manual surface door closer bodies.

1.8 MAINTENANCE SERVICE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Government's continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 - PRODUCTS

2.1 SCHEDULED DOOR HARDWARE

A. General: Provide door hardware for each door to comply with requirements in Door Hardware

Sets and each referenced section that products are to be supplied under.

B. Designations: Requirements for quantity, item, size, finish or color, grade, function, and other distinctive qualities of each type of door hardware are indicated in the Door Hardware Sets at the end of Part 3. Products are identified by using door hardware designations, as follows:

C. Named Manufacturer's Products: Product designation and manufacturer are listed for each door hardware type required for the purpose of establishing requirements. Manufacturers' names are abbreviated in the Door Hardware Schedule.

DOOR HARDWARE 087100 - 6

D. Substitutions: Requests for substitution and product approval for inclusive mechanical and electromechanical door hardware in compliance with the specifications must be submitted in writing and in accordance with the procedures and time frames outlined in Division 01, Substitution Procedures. Approval of requests is at the discretion of the architect, Government, and their designated consultants.

2.2 HANGING DEVICES

A. Hinges: ANSI/BHMA A156.1 certified butt hinges with number of hinge knuckles as specified in the Door Hardware Sets.

1. Quantity: Provide the following hinge quantity, unless otherwise indicated:

a. Two Hinges: For doors with heights up to 60 inches.

b. Three Hinges: For doors with heights 61 to 90 inches.

c. Four Hinges: For doors with heights 91 to 120 inches.

d. For doors with heights more than 120 inches, provide 4 hinges, plus 1 hinge for every 30 inches of door height greater than 120 inches.

2. Hinge Size: Provide the following, unless otherwise indicated, with hinge widths sized for door thickness and clearances required:

a. Widths up to 3’0”: 4-1/2” standard or heavy weight as specified.

b. Sizes from 3’1” to 4’0”: 5” standard or heavy weight as specified.

3. Hinge Weight and Base Material: Unless otherwise indicated, provide the following:

a. Exterior Doors: Heavy weight, non-ferrous, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate standard weight.

b. Interior Doors: Standard weight, steel, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate heavy weight.

4. Hinge Options: Comply with the following where indicated in the Hardware Sets or on

Drawings:

a. Non-removable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while door is closed; for the all out-swinging lockable doors.

5. Acceptable Manufacturers:

a. Hager Companies (HA).

b. McKinney Products (MK).

B. Continuous Geared Hinges: ANSI/BHMA A156.26 Grade 1-600 certified continuous geared hinge. with minimum 0.120-inch thick extruded 6060 T6 aluminum alloy hinge leaves and a minimum overall width of 4 inches. Hinges are non-handed, reversible and fabricated to template screw locations. Factory trim hinges to suit door height and prepare for electrical cut-outs.

DOOR HARDWARE 087100 - 7

1. Acceptable Manufacturers:

a. McKinney Products (MK).

b. Pemko Manufacturing (PE).

c. Stanley Hardware (ST).

2.3 DOOR OPERATING TRIM

A. Flush Bolts and Surface Bolts: ANSI/BHMA A156.3 and A156.16, Grade 1, certified.

1. Manual flush bolts to be furnished with top rod of sufficient length to allow bolt location approximately six feet from the floor.

2. Furnish dust proof strikes for bottom bolts.

3. Surface bolts to be minimum 8” in length and U.L. listed for labeled fire doors and U.L.

listed for windstorm components where applicable.

4. Provide related accessories (mounting brackets, strikes, coordinators, etc.) as required for appropriate installation and operation.

5. Acceptable Manufacturers:

a. Door Controls International (DC).

b. Rockwood Manufacturing (RO).

c. Trimco (TC).

B. Coordinators: ANSI/BHMA A156.3 certified door coordinators consisting of active-leaf, hold-open lever and inactive-leaf release trigger. Model as indicated in hardware sets.

1. Acceptable Manufacturers:

a. Door Controls International (DC).

b. Rockwood Manufacturing (RO).

c. Trimco (TC).

C. Door Push Plates and Pulls: ANS/BHMA A156.6 certified door pushes and pulls of type and design specified in the Hardware Sets. Coordinate and provide proper width and height as required where conflicting hardware dictates.

1. Push/Pull Plates: Minimum .050 inch thick, size as indicated in hardware sets, with beveled edges, secured with exposed screws unless otherwise indicated.

2. Door Pull and Push Bar Design: Size, shape, and material as indicated in the hardware sets. Minimum clearance of 2 1/2-inches from face of door unless otherwise indicated.

3. Offset Pull Design: Size, shape, and material as indicated in the hardware sets. Minimum clearance of 2 1/2-inches from face of door and offset of 90 degrees unless otherwise indicated.

4. Fasteners: Provide manufacturer's designated fastener type as indicated in Hardware Sets.

5. Acceptable Manufacturers:

a. Hiawatha, Inc. (HI).

DOOR HARDWARE 087100 - 8

b. Rockwood Manufacturing (RO).

c. Trimco (TC).

2.4 CYLINDERS AND KEYING

A. General: Cylinder manufacturer to have minimum (10) years experience designing secured master key systems and have on record a published security keying system policy.

B. Source Limitations: Obtain each type of keyed cylinder and keys from the same source manufacturer as locksets and exit devices, unless otherwise indicated.

C. Cylinders: Original manufacturer cylinders complying with the following:

1. Mortise Type: Threaded cylinders with rings and cams to suit hardware application.

2. Rim Type: Cylinders with back plate, flat-type vertical or horizontal tailpiece, and raised trim ring.

3. Bored-Lock Type: Cylinders with tailpieces to suit locks.

4. Mortise and rim cylinder collars to be solid and recessed to allow the cylinder face to be flush and be free spinning with matching finishes.

5. Keyway: Match Facility Restricted Keyway.

D. Permanent Cores: Manufacturer's standard; finish face to match lockset; complying with the following:

1. Interchangeable Cores: Core insert, removable by use of a special key; usable with other manufacturers' cylinders.

E. Keying System: Each type of lock and cylinders to be factory keyed.

1. Conduct specified "Keying Conference" to define and document keying system instructions and requirements.

2. Furnish factory cut, nickel-silver large bow permanently inscribed with a visual key control number as directed by Government.

3. New System: Key locks to a new key system as directed by the Government.

F. Key Quantity: Provide the following minimum number of keys:

1. Change Keys per Cylinder: Two (2)

2. Master Keys (per Master Key Level/Group): Five (5).

3. Construction Keys (where required): Ten (10).

4. Construction Control Keys (where required): Two (2).

5. Permanent Control Keys (where required): Two (2).

G. Construction Keying: Provide temporary keyed construction cores.

H. Key Registration List (Bitting List):

1. Provide keying transcript list to Government's representative in the proper format for importing into key control software.

DOOR HARDWARE 087100 - 9

2. Provide transcript list in writing or electronic file as directed by the Government.

I. Key Control Cabinet: Provide a key control system including envelopes, labels, and tags with self-locking key clips, receipt forms, 3-way visible card index, temporary markers, permanent markers, and standard metal cabinet. Key control cabinet shall have expansion capacity of

150% of the number of locks required for the project.

1. Acceptable Manufacturers:

a. Lund Equipment (LU).

b. MMF Industries (MM).

c. Telkee (TK).

J. Key Control Software: Provide one network version of "Key Wizard" branded key management software package that includes one year of technical support and upgrades to software at no charge. Provide factory key system formatted for importing into “Key Wizard” software.

2.5 MECHANICAL LOCKS AND LATCHING DEVICES

A. Mortise Locksets, Grade 1 (Heavy Duty): ANSI/BHMA A156.13, Series 1000, Operational

Grade 1 certified. Locksets are to be manufactured with a corrosion resistant steel case and be field-reversible for handing without disassembly of the lock body.

1. Acceptable Manufacturers:

a. Corbin Russwin Hardware (RU) – ML2000 Series.

b. Sargent Manufacturing (SA) – 8200 Series.

c. Stanley Best (BE) – 40H Series.

d. Yale Locks and Hardware (YA) – 8800FL Series.

2.6 LOCK AND LATCH STRIKES

A. Strikes: Provide manufacturer's standard strike with strike box for each latch or lock bolt, with curved lip extended to protect frame, finished to match door hardware set, unless otherwise indicated, and as follows:

1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by manufacturer.

2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim.

3. Aluminum-Frame Strike Box: Provide manufacturer's special strike box fabricated for aluminum framing.

4. Double-lipped strikes: For locks at double acting doors. Furnish with retractable stop for rescue hardware applications.

B. Standards: Comply with the following:

1. Strikes for Mortise Locks and Latches: BHMA A156.13.

2. Strikes for Bored Locks and Latches: BHMA A156.2.

DOOR HARDWARE 087100 - 10

3. Strikes for Auxiliary Deadlocks: BHMA A156.5.

4. Dustproof Strikes: BHMA A156.16.

2.7 CONVENTIONAL EXIT DEVICES

A. General Requirements: All exit devices specified herein shall meet or exceed the following criteria:

1. At doors not requiring a fire rating, provide devices complying with NFPA 101 and listed and labeled for "Panic Hardware" according to UL305. Provide proper fasteners as required by manufacturer including sex nuts and bolts at openings specified in the

Hardware Sets.

2. Where exit devices are required on fire rated doors, provide devices complying with

NFPA 80 and with UL labeling indicating "Fire Exit Hardware". Provide devices with the proper fasteners for installation as tested and listed by UL. Consult manufacturer’s catalog and template book for specific requirements.

3. Except on fire rated doors, provide exit devices with hex key dogging device to hold the pushbar and latch in a retracted position. Provide optional keyed cylinder dogging on devices where specified in Hardware Sets.

4. Devices must fit flat against the door face with no gap that permits unauthorized dogging of the push bar. The addition of filler strips is required in any case where the door light extends behind the device as in a full glass configuration.

5. Lever Operating Trim: Where exit devices require lever trim, furnish manufacturer's heavy duty escutcheon trim with threaded studs for thru-bolts.

a. Lock Trim Design: As indicated in Hardware Sets, provide finishes and designs to match that of the specified locksets.

b. Where function of exit device requires a cylinder, provide a cylinder (Rim or

Mortise) as specified in Hardware Sets.

6. Vertical Rod Exit Devices: Where surface or concealed vertical rod exit devices are used at interior openings, provide as less bottom rod (LBR) unless otherwise indicated.

Provide dust proof strikes where thermal pins are required to project into the floor.

7. Narrow Stile Applications: At doors constructed with narrow stiles, or as specified in

Hardware Sets, provide devices designed for maximum 2” wide stiles.

8. Dummy Push Bar: Nonfunctioning push bar matching functional push bar.

9. Rail Sizing: Provide exit device rails factory sized for proper door width application.

10. Through Bolt Installation: For exit devices and trim as indicated in Door Hardware Sets.

DOOR HARDWARE 087100 - 11

B. Conventional Push Rail Exit Devices (Heavy Duty): ANSI/BHMA A156.3, Grade 1 certified panic and fire exit hardware devices furnished in the functions specified in the Hardware Sets.

Exit device latch to be stainless steel, pullman type, with deadlock feature.

1. Acceptable Manufacturers:

a. Corbin Russwin Hardware (RU) - ED4000 / ED5000 Series.

b. Sargent Manufacturing (SA) - 80 Series.

c. Stanley Precision (PR) - Apex 2000 Series.

d. Yale Locks and Hardware (YA) – 7100/7200 Series.

2.8 DOOR CLOSERS

A. All door closers specified herein shall meet or exceed the following criteria:

1. General: Door closers to be from one manufacturer, matching in design and style, with the same type door preparations and templates regardless of application or spring size.

Closers to be non-handed with full sized covers including installation and adjusting information on inside of cover.

2. Standards: Closers to comply with UL-10C for Positive Pressure Fire Test and be U.L.

listed for use of fire rated doors.

3. Cycle Testing: Provide closers which have surpassed 15 million cycles in a test witnessed and verified by UL.

4. Size of Units: Comply with manufacturer's written recommendations for sizing of door closers depending on size of door, exposure to weather, and anticipated frequency of use.

Where closers are indicated for doors required to be accessible to the physically handicapped, provide units complying with ANSI ICC/A117.1.

5. Closer Arms: Provide heavy duty, forged steel closer arms unless otherwise indicated in

Hardware Sets.

6. Closers shall not be installed on exterior or corridor side of doors; where possible install closers on door for optimum aesthetics.

7. Closer Accessories: Provide door closer accessories including custom templates, special mounting brackets, spacers and drop plates, and through-bolt and security type fasteners as required for proper installation.

B. Door Closers, Surface Mounted (Commercial Duty): ANSI/BHMA 156.4, Grade 1 certified surface mounted, institutional grade door closers with complete spring power adjustment, sizes

1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron or aluminum alloy body construction, with adjustable backcheck, closing sweep, and latch speed control valves. Provide non-handed units standard.

1. Acceptable Manufacturers:

DOOR HARDWARE 087100 - 12

a. Corbin Russwin Hardware (RU) - DC6000 Series.

b. Norton Door Controls (NO) - 8500 Series.

c. Sargent Manufacturing (SA) - 1431 Series.

d. Yale Locks and Hardware (YA) - 3500 Series.

2.9 ARCHITECTURAL TRIM

A. Door Protective Trim

1. General: Door protective trim units to be of type and design as specified below or in the

Hardware Sets.

2. Size: Fabricate protection plates (kick, armor, or mop) not more than 2" less than door width (LDW) on stop side of single doors and 1” LDW on stop side of pairs of doors, and not more than 1" less than door width on pull side. Coordinate and provide proper width and height as required where conflicting hardware dictates. Height to be as specified in the Hardware Sets.

3. Protection Plates: ANSI/BHMA A156.6 certified protection plates (kick, armor, or mop), fabricated from the following:

a. Stainless Steel: 300 grade, 050-inch thick.

4. Options and fasteners: Provide manufacturer's designated fastener type as specified in the

Hardware Sets. Provide countersunk screw holes.

5. Acceptable Manufacturers:

a. Hiawatha, Inc. (HI).

b. Rockwood Manufacturing (RO).

c. Trimco (TC).

2.10 DOOR STOPS AND HOLDERS

A. General: Door stops and holders to be of type and design as specified below or in the Hardware

Sets.

B. Door Stops and Bumpers: ANSI/BHMA A156.16, Grade 1 certified door stops and wall bumpers. Provide wall bumpers, either convex or concave types with anchorage as indicated, unless floor or other types of door stops are specified in Hardware Sets. Do not mount floor stops where they will impede traffic. Where floor or wall bumpers are not appropriate, provide overhead type stops and holders.

1. Acceptable Manufacturers:

a. Hiawatha, Inc. (HI).

b. Rockwood Manufacturing (RO).

c. Trimco (TC).

DOOR HARDWARE 087100 - 13

2.11 ARCHITECTURAL SEALS

A. General: Thresholds, weatherstripping, and gasket seals to be of type and design as specified below or in the Hardware Sets. Provide continuous weatherstrip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated. At exterior applications provide non-corrosive fasteners and elsewhere where indicated.

B. Smoke Labeled Gasketing: Assemblies complying with NFPA 105 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for smoke control ratings indicated, based on testing according to UL 1784.

1. Provide smoke labeled perimeter gasketing at all smoke labeled openings.

C. Fire Labeled Gasketing: Assemblies complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to UL-10C.

1. Provide intumescent seals as indicated to meet UL10C Standard for Positive Pressure

Fire Tests of Door Assemblies, and UBC 7-2, Fire Tests of Door Assemblies.

D. Sound-Rated Gasketing: Assemblies that are listed and labeled by a testing and inspecting agency, for sound ratings indicated.

E. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strips are easily replaceable and readily available from stocks maintained by manufacturer.

F. Acceptable Manufacturers:

1. Pemko Manufacturing (PE).

2. Reese Enterprises, Inc. (RE).

3. Zero (ZE).

2.12 FABRICATION

A. Fasteners: Provide door hardware manufactured to comply with published templates generally prepared for machine, wood, and sheet metal screws. Provide screws according to manufacturers recognized installation standards for application intended.

2.13 FINISHES

A. Standard: Designations used in the Hardware Sets and elsewhere indicate hardware finishes complying with ANSI/BHMA A156.18, including coordination with traditional U.S. finishes indicated by certain manufacturers for their products.

B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware.

DOOR HARDWARE 087100 - 14

C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine scheduled openings, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance.

B. Notify architect of any discrepancies or conflicts between the door schedule, door types, drawings and scheduled hardware. Proceed only after such discrepancies or conflicts have been resolved in writing.

3.2 PREPARATION

A. Hollow Metal Doors and Frames: Comply with ANSI/DHI A115 series.

B. Wood Doors: Comply with ANSI/DHI A115-W series.

3.3 INSTALLATION

A. Install each item of mechanical and electromechanical hardware and access control equipment to comply with manufacturer's written instructions and according to specifications.

1. Installers are to be trained and certified by the manufacturer on the proper installation and adjustment of fire, life safety, and security products including: hanging devices; locking devices; closing devices; and seals.

B. Mounting Heights: Mount door hardware units at heights indicated in following applicable publications, unless specifically indicated or required to comply with governing regulations:

1. Standard Steel Doors and Frames: DHI's "Recommended Locations for Architectural

Hardware for Standard Steel Doors and Frames."

2. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for

Wood Flush Doors."

3. Where indicated to comply with accessibility requirements, comply with ANSI A117.1

"Accessibility Guidelines for Buildings and Facilities."

4. Provide blocking in drywall partitions where wall stops or other wall mounted hardware is located.

C. Retrofitting: Install door hardware to comply with manufacturer's published templates and written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work specified in Division 9

DOOR HARDWARE 087100 - 15

Sections. Do not install surface-mounted items until finishes have been completed on substrates involved.

D. Thresholds: Set thresholds for exterior and acoustical doors in full bed of sealant complying with requirements specified in Division 7 Section "Joint Sealants."

E. Storage: Provide a secure lock up for hardware delivered to the project but not yet installed.

Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation.

3.4 FIELD QUALITY CONTROL

A. Field Inspection: Supplier will perform a final inspection of installed door hardware and state in report whether work complies with or deviates from requirements, including whether door hardware is properly installed, operating and adjusted.

3.5 ADJUSTING

A. Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.

3.6 CLEANING AND PROTECTION

A. Protect all hardware stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame.

B. Clean adjacent surfaces soiled by door hardware installation.

C. Clean operating items as necessary to restore proper finish. Provide final protection and maintain conditions that ensure door hardware is without damage or deterioration at time of

Government occupancy.

3.7 DEMONSTRATION

A. Instruct Government's maintenance personnel to adjust, operate, and maintain mechanical and electromechanical door hardware.

3.8 DOOR HARDWARE SETS

A. The hardware sets represent the design intent and direction of the Government and architect.

They are a guideline only and should not be considered a detailed hardware schedule.

Discrepancies, conflicting hardware and missing items should be brought to the attention of the

DOOR HARDWARE 087100 - 16

architect with corrections made prior to the bidding process. Omitted items not included in a hardware set should be scheduled with the appropriate additional hardware required for proper application and functionality.

B. Manufacturer’s Abbreviations:

1. MK - McKinney

2. MR - Markar

3. PE - Pemko

4. RO - Rockwood

5. RU - Corbin Russwin

6. BE - Stanley Security Solutions Inc (BE)

7. RF - Rixson

8. 00 - Other

9. SU – Securitron

HARDWARE SCHEDULE

HW SET # 1.0

Doors: 102

Each to have:

1 Continuous Hinge MCK-12HD BZ MK

1 Rim Exit Device ED5200 TH957 613 RU

1 Cylinder 1E-7 AS REQUIRED 613 BE

1 Door Closer DC6210 A11 x BRKTS REQUIRED 690 RU

1 Threshold 171A PE

1 Set Weatherstrip BY DOOR MANUFACTURER 00

NOTE: CARD READER, DOOR POSITION SWITCH AND ELECTRIC DOOR STRIKE AND

ACCESSORIES FURNISHED BY GOVERNMENT’S SECURITY INTEGRATOR.

HW SET # 2.0

Doors: 101A

Each to have:

2 Continuous Hinge MCK-12HD BZ MK

2 Set Door Pull RM351-2 x MTG T1HD US10B RO

2 Door Closer DC6210 A11 x BRKTS REQUIRED 690 RU

1 Set Weatherstrip BY DOOR MANUFACTURER 00

HW SET # 3.0

Doors: 114

Each to have:

1 Continuous Hinge MCK-14HD CL MK

1 Rim Exit Device ED5200 L957 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

DOOR HARDWARE 087100 - 17

1 Door Closer DC6210 A4 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

1 Rain Drip 346C PE

1 Door Bottom Sweep 3452CNB PE

NOTE: DOOR POSITION SWITCH AND ACCESSORIES FURNISHED BY GOVERNMENT’S

SECURITY INTEGRATOR.

HW SET # 4.0

Doors: 110, 111C, 111D

Each to have:

1 Continuous Hinge MCK-14HD CL MK

1 Rim Exit Device ED5200 TH957 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6210 A4 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

NOTE: DOOR 110 - CARD READER, DOOR POSITION SWITCH AND ELECTRIC DOOR STRIKE

AND ACCESSORIES FURNISHED BY GOVERNMENT’S SECURITY INTEGRATOR.

HW SET # 4.1

Doors: 160A

Each to have:

1 Continuous Hinge MCK-12HD BZ MK

1 Rim Exit Device ED5200 TH957 613 RU

1 Cylinder 1E-7 AS REQUIRED 613 BE

1 Door Closer DC6210 A11 x BRKTS REQUIRED 690 RU

1 Set Weatherstrip BY DOOR MANUFACTURER PE

HW SET # 5.0

NOT USED

HW SET # 6.0

Doors: 113

Each to have:

1 Continuous Hinge MCK-14HD CL MK

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6210 A4 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

DOOR HARDWARE 087100 - 18

1 Set Weatherstrip 303AS PE

1 Rain Drip 346C PE

1 Door Bottom Sweep 3452CNB PE

NOTE: DOOR POSITION SWITCH AND ACCESSORIES FURNISHED BY GOVERNMENT’S

SECURITY INTEGRATOR.

HW SET # 7.0

Doors: 158B

Each to have:

1 Continuous Hinge MCK-14HD CL MK

1 Apartment Lock ML2067 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6210 A4 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

HW SET # 8.0

Doors: 141

Each to have:

2 Continuous Hinge MCK-14HD CL MK

1 Set Combo Flush Bolts 2845/2945 US26D RO

1 Dust Proof Strike 570 US26D RO

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Coordinator 2600 x FILLER BAR x MTG BRKTS US28 RO

2 Door Closer DC6210 A4 689 RU

2 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

1 Rain Drip 346C PE

2 Door Bottom Sweep 3452CNB PE

2 Astragal 18041CNB PE

NOTE: CARD READER, DOOR POSITION SWITCH AND MAGNETIC LOCK AND

HW SET # 8.1

Doors: 124A

Each to have:

1 Continuous Hinge MCK-14HD CL MK

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Door Closer DC6210 A4 689 RU

DOOR HARDWARE 087100 - 19

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

NOTE: DOOR POSITION SWITCH, ELECTRIC DOOR STRIKE AND ACCESSORIES FURNISHED

BY GOVERNMENT’S SECURITY INTEGRATOR..

HW SET # 9.0

Doors: 119B

Each to have:

2 Continuous Hinge MCK-14HD CL MK

1 Set Combo Flush Bolts 2845/2945 US26D RO

1 Dust Proof Strike 570 US26D RO

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Coordinator 2600 x FILLER BAR x MTG BRKTS US28 RO

2 Door Closer DC6210 A5 689 RU

2 Kick Plate K1050 8" CSK 3BE US32D RO

1 Threshold 2005AT PE

1 Set Weatherstrip 303AS PE

1 Rain Drip 346C PE

2 Door Bottom Sweep 3452CNB PE

2 Astragal 18041CNB PE

HW SET # 10.0

Doors: 101B

Each to have:

2 Continuous Hinge MCK-12HD BZ MK

2 Push Pull Set RM351-2 x MTG T1HD US10B RO

2 Door Closer DC6210 A11 x BRKTS REQUIRED 690 RU

ACCESSORIES FURNISHED BY GOVERNMENT’S SECURITY INTEGRATOR..

HW SET # 11.0

Doors: 111A, 111B, 115, 151

Each to have:

Hinge TA2714 US26D MK

1 Rim Exit Device ED5200 L955 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6210 A4 689 RU

3 Silencer 608 RO

DOOR HARDWARE 087100 - 20

NOTE: DOORS 115 AND 151 - CARD READER, ELECTRIC DOOR STRIKE AND ACCESSORIES

FURNISHED BY GOVERNMENT’S SECURITY INTEGRATOR.

HW SET # 12.0

Doors: 135, 136

Each to have:

Hinge TA2714 US26D MK

1 Privacy Set w/Indicator ML2060 LWA M19V 630 RU

1 Door Closer DC6200 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Door Stop 406/441CU 32D/26D RO

HW SET # 13.0

Doors: 119C, 125, 126, 127, 128, 129, 130, 131, 132, 134, 138, 139, 140, 145, 146, 156, 157, 158A, 159

Each to have:

Hinge TA2714 US26D MK

1 Office Lock ML2051 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

HW SET # 14.0

Doors: 107, 149A, 149B

Each to have:

Hinge TA2714 (NRP x SSF @ 149A & 149B) US26D MK

1 Entrance Lock ML2053 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

NOTE: CARD READER, ELECTRIC DOOR STRIKE AND ACCESSORIES FURNISHED BY

GOVERNMENT’S SECURITY INTEGRATOR.

DOOR 149A TO RECEIVE KABA MAS CDX-10 HIGH SECURITY LOCK, FURNISHED BY

HW SET # 15.0

Doors: 103C, 123

Each to have:

Hinge TA2714 US26D MK

1 Classroom Lock ML2055 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

HW SET # 16.0

Doors: 103A, 104, 108, 120

Each to have:

Hinge TA2714 US26D MK

DOOR HARDWARE 087100 - 21

1 Classroom Lock ML2055 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6200 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Set Door Seals/Silencers S773D/608 AS REQUIRED PE

HW SET # 16.1

Doors: 137, 155

Each to have:

1 Continuous Hinge MCK-12HD CL MK

1 Classroom Lock ML2055 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6200 x BRKTS REQUIRED 689 RU

1 Set Door Seals BY DOOR MANUFACTURER 00

NOTE: DOOR 155 - CARD READER, ELECTRIC DOOR STRIKE AND ACCESSORIES

FURNISHED BY GOVERNMENT’S SECURITY INTEGRATOR.

HW SET # 17.0

Doors: 109, 116, 117, 118, 124C, 133

Each to have:

Hinge TA2714 US26D MK

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6200 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

HW SET # 17.1

Doors: 105B, 111E

Each to have:

Hinge TA2714 US26D MK

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Door Closer DC6210 A4 689 RU

HW SET # 18.0

Doors: 119A

Each to have:

Hinge TA2714 US26D MK

1 Set Auto Flush Bolts 2842/2942 US26D RO

1 Dust Proof Strike 570 US26D RO

1 Classroom Lock ML2055 LWA LC 630 RU

DOOR HARDWARE 087100 - 22

1 Coordinator 2600 x FILLER BAR Black RO

2 Door Closer DC6200 689 RU

2 Kick Plate K1050 8" CSK 3BE US32D RO

2 Door Stop 406/441CU 32D/26D RO

HW SET # 19.0

Doors: 111F, 112, 153

Each to have:

Hinge TA2714 US26D MK

1 Set Combo Flush Bolts 2845/2945 US26D RO

1 Dust Proof Strike 570 US26D RO

1 Storeroom Lock ML2057 LWA LC 630 RU

1 Cylinder 1E-7 AS REQUIRED 626 BE

1 Coordinator 2600 x FILLER BAR x MTG BRKTS US28 RO

2 Door Closer DC6210 A4 689 RU

2 Kick Plate K1050 8" CSK 3BE US32D RO

HW SET # 20.0

Doors: 105, 106

Each to have:

Hinge TA2714 US26D MK

1 Push Plate 70F US32D RO

1 Pull Plate 111 x 70C US32D RO

1 Door Closer DC6200 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

1 Door Stop 482 US26D RO

HW SET # 21.0

Doors: 160B

Each to have:

1 Continuous Hinge MCK-12HD BZ MK

1 Set Push Pulls RM351-2 x MTG T1HD US10B RO

1 Door Closer DC6210 A11 x BRKTS REQUIRED 690 RU

HW SET # 22.0

Doors: 147, 148

Each to have:

1 Barn Door Trackset Assembly 280C-SWTKIT x LAR PE

1 Set Door Pulls 111BTB5HD US32D RO

HW SET # 23.0

Doors: 122

DOOR HARDWARE 087100 - 23

Hinge TA2714 US26D MK

1 Passage Set ML2010 LWA 630 RU

1 Door Closer DC6200 689 RU

1 Kick Plate K1050 8" CSK 3BE US32D RO

NOTE: CARD READER, ELECTRIC DOOR STRIKE AND ACCESSORIES FURNISHED BY

HW SET # 24.0 (ABI #2)

Doors: 111G, 111H, 111J

NOTE: ALL HARDWARE FURNISHED IN OTHER SECTION BY PARTITION DOOR

MANUFACTURER.

HW SET # 25.0

Doors: 124B

NOTE: OVERHEAD DOOR - ALL HARDWARE FURNISHED IN OTHER SECTION BY

PARTITION DOOR MANUFACTURER.

END OF SECTION 087100