IC-OUM-07022_Rev1.2_B3.pdf
PDF 1 MB Posted
- Attached to
- eXportable Combat Training Capability (XCTC)
- Solicitation number
- W900KK-19-R-0003
About this file
This synopsis announces a draft solicitation for the eXportable Combat Training Capability program. The U.S. Army Contracting Command - Orlando plans to award a full and open contract to develop adaptive leaders and enable platoons to achieve trained proficiency in core functions by providing a capstone training event for Brigade Combat Teams to attain T-Level 3 readiness. Interested parties are encouraged to submit questions, comments, and recommendations on the draft solicitation by March 4, 2019 to improve the final solicitation. The notice does not constitute a commitment to award any related contracts.
Item 34: Wireless Backhaul Configuration Manual
View the file
Other files
Show 40 more
50 files listed here. See the rest on GovTribe.
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
IC-OUM-007022 Rev 1.2 9/27/2017
Operator User Manual for the Wireless Backhaul Configuration
Date: 4 December 2015
Prepared by: Michael James
Operator User Manual for the Wireless Backhaul Configuration
CHANGE LOG
CHANGE / REVISION RECORD
Revision Page(s) Description of Change Made By Date Approved By
1.0 All Initial Release
Michael James
10/4/2017
1.1
1.2 All Revised and Reformatted Jacky Ngai
9/27/2017 James
DePersis
Operator User Manual for the Wireless Backhaul Configuration
Table of Contents
1. Introduction
1.1 General Information
1.1.1 Scope
1.1.2 Safety
1.1.3 Security
1.1.4 List of Abbreviations/Acronyms
1.2 Equipment Description
1.2.1 Equipment Characteristics, Capabilities, and Features
1.2.2 Equipment Data
1.3 Principles of Operation
2. Operating Instructions
2.1 Description and Use of Operator’s Controls and Indicators
2.2 Operation under Usual Conditions
2.2.1 Preparation for Operation
2.2.2 Operation
2.2.3 Termination
2.2.4 Removal
2.2.5 Preparation for Storage
2.2.6 Preparation for Shipment
2.3 Operation under Unusual Conditions
2.3.1 Unusual Environment
2.3.2 Emergency Procedures
3. Operator Maintenance Instructions
3.1 Troubleshooting
3.2 Maintenance Procedures
4. Special Tools/Installation Equipment
5. Appendix
Table of Figures Figure 1. Point to Point Link Figure 2. Point to Point Link Main and Failover Connectors Figure 3. 48V 0.5A PoE injector for Point to Point Link Figure 4. Point to Point Link Figure 5. Point to Point Link Main Connector Figure 6. 24V 1A PoE injector for Point to Point Link Figure 7. Start Menu Showing “View Network Connections” Figure 8. Showing Local Area Connections Properties Figure 9. Local Area Connections Properties Widow Figure 10. Showing IPv4 Settings Figure 11. PoE injector with Ethernet cable inserted in PoE port Figure 12. Point to Point Link with Ethernet cable inserted into Primary LAN port Figure 13. PoE injector with Ethernet cables Figure 14. Showing certificate error Figure 15. Showing the Point to Point Link Login page Figure 16. Showing the Point to Point Link main page Figure 17. Showing password change request Figure 18. Showing settings for Station Figure 19. Showing settings for Access Point Figure 20. Showing settings for network Figure 21. Showing advance settings for the Station configuration Figure 22. Showing advance settings for the Access Point configuration Figure 23. Showing the User Name and Password fields Figure 24. Showing the User Name and Password fields
List of Tables No list of table entries found.
Operator User Manual for the Wireless Backhaul Configuration
1. Introduction
1.1 General Information
1.1.1 Scope
This operator’s manual for the Wireless Backhaul Configurations focuses on the functionality and program configurations of the wireless backhauls utilized within the FlexTrain program.
1.1.2 Safety
Use safety when handling the equipment even though most of the equipment is mounted in rugged cases, it is still required that all personnel must handle all Communication Shelter Electronics (CSE) equipment with caution during loading, unloading, and installation. Damage may occur if the equipment is dropped or mishandled. DO NOT attempt to lift heavy equipment by yourself, use the 2-person lift. Use caution when deploying the CSE’s during adverse conditions, i.e. thunderstorms, dust storms etc., as the communications shelter (comms shelter) may be energized with electricity. The comms shelter, Integrated Tower System trailer (ITS trailer), and ground platform should always be installed on level ground, anchored, and grounded in accordance with IC09015 and IC-OUM09015.
Operator User Manual for the Wireless Backhaul Configuration
1.1.3 Security
Not Applicable
1.1.4 List of Abbreviations/Acronyms
Admin Comms Administrative Communications Suite
CSE Communication Shelter Electronics
Comms Shelter Communication Shelter
I&C Instrumentation and Communications
IAW In Accordance With
ITS Trailer Integrated Tower System Trailer (Portable Tower)
LAN Local Area Network
NetOps Network Operations
NOC Network Operations Center
NOTL Network Operations Team Leader
PDU Power Distribution Unit
PoE Power over Ethernet
RF Radio Frequency
RF Tech Radio Frequency Technician
UHF Ultra High Frequency
UPS Uninterruptible Power Supply
1.2 Equipment Description
The wireless backhaul equipment used is the same in functionality and operations, and is either 2.4GHz or 5GHz, providing us with the point to point RF path that seamlessly maintains our connectivity between all the ITS trailers, the NOC, and other units during the exercise. Below is an example of each style of wireless backhaul and their description. Refer to IC-07004 and IC-OUM-07004 (ITS Tower Masthead) for installation procedures.
Operator User Manual for the Wireless Backhaul Configuration
Figure 1. Point to Point Link.
Figure 2. Point to Point Link Main and Failover Connectors
Operator User Manual for the Wireless Backhaul Configuration
Figure 3. 48V 0.5A PoE injector for Point to Point Link
Figure 4. Point to Point Link
Operator User Manual for the Wireless Backhaul Configuration
Figure 5. Point to Point Link Main Connector
Figure 6. 24V 1A PoE injector for Point to Point Link
1.2.1 Equipment Characteristics, Capabilities, and Features
Not Applicable
Operator User Manual for the Wireless Backhaul Configuration
1.2.1.1 Functions of …
Not Applicable
1.2.2 Equipment Data
Not Applicable
1.3 Principles of Operation
The wireless backhaul equipment provides a wireless bridge for transporting network data from ITS towers back to the NOC.
2. Operating Instructions
2.1 Description and Use of Operator’s Controls and Indicators Not Applicable
2.2 Operation under Usual Conditions
Not Applicable
2.2.1 Preparation for Operation
a. Open box and inventory items
a. Point to Point Link
b. PoE (power over Ethernet w/cord
c. GPS antenna (if equipped)
b. Laptop network adapter changes
a. Turn on laptop
b. Click on start menu. Type in “View Network Connections” and press the Enter. As shown on Figure 7.
Operator User Manual for the Wireless Backhaul Configuration
Figure 7. Start Menu Showing “View Network Connections”
c. Right click on “Local Area Connection”, then click on “Properties” As shown in Figure 8.
Operator User Manual for the Wireless Backhaul Configuration
Figure 8. Showing Local Area Connections Properties
d. Properties window will open up, click “Internet Protocol Version 4 (TCP/IPv4), then Click Properties button. As shown in Figure 9.
Figure 9. Local Area Connections Properties Widow
e. Change from “Obtain an IP address automatically” to “Use the following IP address”.
f. IP address block, pick an IP of 192.168.1.xx (for xx pick a number between 240 and 254). As shown in Figure 10.
Figure 10. Showing IPv4 Settings
g. Click “OK” and close out remaining windows.
c. Powering up the Point to Point Link
a. Plug in the PoE injector to the wall outlet.
b. Plug in an Ethernet cable to the PoE port on the PoE.
c. Plug in the other end of the Ethernet into the primary LAN port of the backhaul equipment. As shown on Figures 11 and 12.
Operator User Manual for the Wireless Backhaul Configuration
Figure 11. PoE injector with Ethernet cable inserted in PoE port
Operator User Manual for the Wireless Backhaul Configuration
Figure 12. Point to Point Link with Ethernet cable inserted into Primary LAN port.
d. Plug another Ethernet cable into the LAN port of the POE, then plug the other end into your laptop’s Ethernet jack. As shown in Figure 13.
Figure 13. PoE injector with Ethernet cables.
d. Accessing the Point to Point Link from the laptop
a. Start Internet Explorer and navigate to “192.168.1.20” in the address bar. (NOTE) You may also use the UBNT discover tool, if this is not on the laptop you are using, contact your NOTL for installation.
b. If presented with a certificate problem, click “Continue to this website (not recommended).” As shown in Figure 14.
Operator User Manual for the Wireless Backhaul Configuration
Figure 14. Showing certificate error
c. In both the Username and Password enter “ubnt”. For Country select “United States”.
As shown in Figure 15.
Operator User Manual for the Wireless Backhaul Configuration
Figure 15. Showing the Point to Point Link Login page.
d. Check the “I agree to these TERMS OF USE and FIRMWARE LICENSE AGREEMENT” and procced to click Login. As shown in Figure 16.
Figure 16. Showing the Point to Point Link main page.
e. If prompted with a password change request. Consult the NOTL for the password. As shown in Figure 17.
Operator User Manual for the Wireless Backhaul Configuration
Figure 17. Showing password change request.
2.2.1.1 Installation...
a. Configuring Point to Point Link as Station
a. Click on the Wireless tab and follow Figure 18 for settings. Consult the NOTL for SSID and the WPA2 Preshared Key.
Operator User Manual for the Wireless Backhaul Configuration
Figure 18. Showing settings for Station.
b. Click Change then click Apply.
c. Configuring Point to Point Link as Access Point
d. Click on the Wireless tab and follow Figure 19 for settings. Consult the NOTL for SSID, the WPA2 Preshared Key, frequency, and any other specific changes.
Operator User Manual for the Wireless Backhaul Configuration
Figure 19. Showing settings for Access Point.
e. Click Change then click Apply.
f. Network Configurations
a. Click on the Network tab and follow Figure 20 for settings. Consult the NOTL for IP address and any other specific changes.
Operator User Manual for the Wireless Backhaul Configuration
Figure 20. Showing settings for network.
b. Click Change then click Apply.
c. Advance settings
a. Click on the Advance tab and follow Figure 21 or 22 for settings, depending on the Point to Point Link being set as a Station or Access Point, respectively. Consult the NOTL any other specific changes.
Figure 21. Showing advance settings for the Station configuration.
Operator User Manual for the Wireless Backhaul Configuration
Figure 22. Showing advance settings for the Access Point configuration.
b. Click Change then click Apply.
c. Service Settings
a. Click the on the System tab.
b. Change the Username. Consult the NOTL for the User Name
c. To change the password, click the change password button. Refer to figure 23.
Operator User Manual for the Wireless Backhaul Configuration
Figure 23. Showing the User Name and Password fields.
d. Click Change then click Apply.
e. Consult the NOTL any other specific changes.
f. Service Settings
No changes will be made in the Service tab.
g. System Settings
a. Click the on the System tab.
b. Change the Username. Consult the NOTL for the User Name
c. To change the password, click the change password button. Refer to figure 24.
Operator User Manual for the Wireless Backhaul Configuration
Figure 24. Showing the User Name and Password fields.
d. Click Change then click Apply.
e. Consult the NOTL any other specific changes.
f. System Backup and Restoration
a. To back up the settings, proceed to the system tab and click download on “Back Up Configuration”
b. To restore click browse and navigate to the backed up “.cfg” file. Click open, click upload, then click apply.
2.2.1.2 Power-up and Initialize
Not Applicable
2.2.2 Operation
Not Applicable
2.2.3 Termination
Operator User Manual for the Wireless Backhaul Configuration
2.2.4 Removal
Not Applicable
2.2.5 Preparation for Storage
Not Applicable
2.2.6 Preparation for Shipment
Not Applicable
2.3 Operation under Unusual Conditions
Caution should always be observed during adverse weather conditions. Take caution that any debris or weather may cause slippery footing both inside, outside and in or around the ITS trailers.
2.3.1 Unusual Environment
Not Applicable
2.3.1.1 Lightning
During severe electrical or lightning storms, operations in and around the ITS trailers should be conducted only in emergency situations.
2.3.1.2 Strong Winds
During strong winds, operations in and around the ITS trailers should be conducted only in emergency situations.
2.3.1.3 Cold
Not Applicable
2.3.2 Emergency Procedures
Operator User Manual for the Wireless Backhaul Configuration
3. Operator Maintenance Instructions Not Applicable
3.1 Troubleshooting
a. Observation
Electrical outlets are non-functioning. No power at the wall mounted outlets or PDU.
b. Solutions
Open circuit breaker panel and check for any breakers in the off or disconnected position. This includes the PDU breaker panel.
a. Observation
Laptop will not access equipment
b. Solutions
Check IP address on the laptop
a. Observation
Unable to access Point to Point Link due to unknown password or username
b. Solutions
c. Hold the reset button for 30 seconds, use a paperclip.
3.2 Maintenance Procedures
Not Applicable
4. Special Tools/Installation Equipment
a. 2-10ft lengths of Ethernet cables
b. Laptop
c. PoE
5. Appendix
| 1. Introduction |
| 1.1 General Information |
| 1.1.1 Scope |
| 1.1.2 Safety |
| 1.1.3 Security |
| 1.1.4 List of Abbreviations/Acronyms |
| 1.2 Equipment Description |
| 1.2.1 Equipment Characteristics, Capabilities, and Features |
| 1.2.1.1 Functions of … |
1.2.2 Equipment Data
1.3 Principles of Operation
| 2. Operating Instructions |
| 2.1 Description and Use of Operator’s Controls and Indicators |
| 2.2 Operation under Usual Conditions |
| 2.2.1 Preparation for Operation |
| 2.2.1.1 Installation... |
| 2.2.1.2 Power-up and Initialize |
| 2.2.2 Operation |
| 2.2.3 Termination |
| 2.2.4 Removal |
| 2.2.5 Preparation for Storage |
| 2.2.6 Preparation for Shipment |
| 2.3 Operation under Unusual Conditions |
| 2.3.1 Unusual Environment |
| 2.3.1.1 Lightning |
| 2.3.1.2 Strong Winds |
| 2.3.1.3 Cold |
2.3.2 Emergency Procedures
| 3. Operator Maintenance Instructions |
| 3.1 Troubleshooting |
| 3.2 Maintenance Procedures |
| 4. Special Tools/Installation Equipment |
| 5. Appendix |
File details come from the government source that posted it. Updated .