Attach_0006_Product_Engineering_Requirements_(003).docx

Attachment A006

PRODUCT ENGINEERING REQUIREMENTS

The following Item Description, Drawing(s) and/or Specification(s) represent minimum Government requirements and are applicable to this Procurement.

National Stock Number (NSN): 5180-01-605-5146

Tool Kit, General Mechanics

In accordance with Army Technical Data Package List (TDPL) 0627A0000:59678, dated 12 June 2017.

With the following exceptions:

Army drawing 0705D2011, Rev A, dated 02 June 2017, Zone B3, under part number 0705D2011-7, remove “VD619MMR” and replace with “VD621MMR”.

Army drawing 0720B0000, Rev A, dated 02 June 2017, Zone B3, under part number 0720B0000-5, remove vendor part number “PPC103A” and replace with “PPC104A”.

Army drawing 0701C0004, Rev A, dated 02 June 2017, Zone B3, under part number 0701C0004-5, remove vendor part number “M82R” and replace with “M92R”.

Army drawing 0714A0009, Rev A, dated 02 June 2017, Zone B3, under part number 0714A0009-3, remove vendor part number “J1224-T5000” and replace with “J1224-T500”.

Army drawing 0713C1006, Rev A, dated 02 June 2017, Zone B3, under part number 0713C1006-4, remove vendor part number “J44903/8” and replace with “J49903/8”.

Army drawing 0720H0000, Rev A, dated 02 June 2017:

Zone B3-B4, add source:

“Part No.: 0720H0000-5 Name & Address: STANLEY PROTO INDUSTRIAL

2195 E VIEW PKWY STE 103

CONYERS, GA 30013

CAGE CODE: 1CV05

VENDOR PART NO.: J2130

VENDOR DESCRIPTION: 16” ROLLING HEAD PRY BAR”

Zone C4, under “MAXIMUM DISTANCE BETWEEN CHISEL POINT AND ROUNDED PRY BAR END MEASURED PARALLEL TO BAR (C)”, remove “9/16 INCH” and replace with “5/8 INCH”.

Army drawing 0627B0000, dated 25 October 2015:

. Page 3, note 3.8.1, line 3, remove "316 STAINLESS STEEL OR ELECTROPOLISHED 304 STAINLESS STEEL" and replace with "316 STAINLESS STEEL

OR 304 STAINLESS STEEL”.

Army drawing 0627D1031, Rev A, dated 02 June 2017:

Army TDPL 0627D0000:59678, dated 12 June 2017:

Quality Assurance Provision (QAP) 0627E0001, page 2, Remove Section 2 in its entirety and replace with:

"2. First Article Inspection or Product Verification Test. Unless otherwise specified in the contract, a first article or product verification sample consisting of four (4) of each QAP item(s), each with a means of being loaded to 120 lbs, shall be submitted for inspection. Each test, with the exception of STM-10 and STM-11, shall be performed once on any of the four (4) QAP items of the contractor's choice. STM-10 and STM-11 are only required to be performed once utilizing all four (4) QAP items, each in any relative position. Testing and approval shall be in accordance with the terms and conditions of the contract. The first article or product verification sample shall be manufactured using the same vendors, methods, materials, equipment, processes and facilities as will be used during regular production. The first article or product verification sample shall be submitted for inspection and approval in accordance with the terms of the contract. If there is any change of vendors, methods, materials, equipment, facilities, or lot interfix, or if there is a 6-month break in production, the Contracting Officer shall be notified and at the discretion of the Government a new full or partial first article or product verification inspection may be required. Failure of any sample unit to comply with any or all of the requirements of the applicable drawings, specifications or QAP's shall be cause for rejection of the first article or product verification sample."

{Army Drawing 0705D2004, Revision A, dated 2 June 2017:

*Zone B3, Part number 0705D2004-5 in the Approved Source(s) table, remove Vendor Part No. "44014" and replace with "40014"

Army Drawing 0712A0000, Revision A, dated 2 June 2017:

*Zone B3, Part number 0712A0000-4 in the Approved Source(s) table, remove "SCREWDRIVER, FLAT TIP, CABINET, 3/16", 6" BLADE" and replace with

"SCREWDRIVER, PHILLIPS, #2, STUBBY"}

Specifications and standards listed in the above document are the revisions in effect as of the date of 12 June 2017.