TMP Architecture, Inc. TMP17109D

11/24/20 CONSTRUCTION DOCUMENTS DOOR HARDWARE

08 7100-5

3. Hinges manufactured by Stanley, Hager and McKinney are also acceptable.

B. Continuous Gear Hinge:

1. 6063-T6 aluminum alloy, anodized finish (cap on entire hinge painted if specified).

Manufacture to template, uncut hinges non-handed, pinless assembly, three interlocking extrusions, full height of door and frame, fasteners 410 stainless steel plated and hardened. Anodizing of material shall be done after fabrication of components so that all bearing slots are anodized.

2. Length: 1" less than door opening height. Fastener 12-24 x 1/2" #3 Phillips keen form stainless steel self-tapping at aluminum and hollow metal doors, 12- 1/2" #3 Philips, flathead full thread at wood doors.

3. Furnish fire rated hinges "FR" at labeled openings.

4. Numbers used are Ives.

a. For Aluminum frames;

1) Ives 112XY

2) Equal products by Hager & Select will also be accepted.

C. Locksets and Latchsets - Mortise Type:

1. Function numbers are Best.

a. Best 45H

2. Lockset Trim:

a. Best 3J

3. Provide strikes with extended lips where required to protect trim from being marred by latch bolt. Provide strike lips that do not project more than 1/8" beyond door frame trim at single doors and have 7/8" lip to center at pairs of 1-3/4" doors.

D. Exit Devices:

1. Exit devices shall be touchpad style, fabricated of brass, bronze, stainless steel, or aluminum, plated to the standard architectural finishes to match the balance of the door hardware.

2. All exit devices shall incorporate a fluid damper, which decelerates the touchpad on its return stroke and eliminates noise associated with exit device operation. Touchpad shall extend a minimum of one half of the door width. All latchbolts to be deadlatching type, with a self-lubricating coating to reduce wear.

3. End-cap will be sloped to deflect any impact from carts and they shall be flush with the external mechanism case. End caps that overlap and project above the mechanism case are unacceptable. End cap shall utilize a two-point attachment to the mounting bracket.

4. Touchpad shall match exit device finish, and shall be stainless steel for US26, US26D, US28, US32, and US32D finishes. Only compression springs will be used in devices, latches, and outside trims or controls.

5. Plastic templates shall be included with each exit device to facilitate a quick, easy and accurate installation.

6. Strikes shall be roller type and come complete with a locking plate to prevent movement.

7. All rim and vertical rod exit devices shall have passed a 5 million(5,000,000) cycle test based on ANSI A156.3, 1994, Grade 1 test standards and certified by an independent testing lab.

08 7100-6

8. All mortise exit devices shall have passed a 10 million(10,000,000)cycle test based on ANSI A156.3, 1994, Grade 1 test standards and certified by an independent testing lab.

9. Provide cylinder dogging on panic exit hardware where noted in hardware sets.

10. Exit devices shall be UL listed panic exit hardware. All exit devices for fire rated openings shall be UL labeled fire exit hardware.

11. Lever trim for exit devices shall be vandal-resistant type, which will travel to a 90-degree down position when more than 35 pounds of torque are applied, and which can easily be re-set.

12. Von Duprin 35A/98 Series. Series and function numbers as listed in sets.

13. Trim:

a. As specified in sets.

b. Levers to match lockset design where specified.

E. Removable Mullion:

a. Interior/Exterior, mullion is removable only through the use of building keys.

1) Von Duprin KR4954

b. Interior Doors - UL listed, Mullion is removable only through the use of building keys.

1) Von Duprin KR9954

F. Push and Pull Hardware:

1. Push Plates: Ives 8200 Series 4 x 16 x .050 inches.

2. Pull, Offset: One inch round rod, 90 degree offset, 12 inch centers.

3. Pull Plates: Ives 8302-8 4 x 16 x .050 inches. 8” center.

4. Manufacturer: Provide push and pull hardware from any member of B.H.M.A.

G. Electric Strike:

1. Electric strikes shall provide remote release of latchbolts. They shall be designed for use with the type locks shown at each opening where required. Strikes will be UL Listed for Burglary-Resistant Electric Door Strike, and where required, shall be UL listed as electric strikes for Fire Doors or Frames. Faceplates shall be stainless steel with finish as specified for each opening. The locking components shall be stainless steel to resist damage and abuse.

2. Solenoids shall be of the continuous duty type for the voltage specified. Plug connectors will be furnished. Strikes shall have an adjustable backbox to compensate for misalignment of door and frame.

3. Numbers used in sets are Von Duprin.

a. Von Duprin 6000 series

H. Closers:

1. Door closers shall have fully hydraulic, full rack and pinion action with a high strength cast iron cylinder. Cylinder body shall be 1 ½” in diameter, and double heat treated pinion shall be 11/16” in diameter with double D slab drive arm connection.

2. Hydraulic fluid shall be of a type requiring no seasonal closer adjustment for temperatures ranging from 120 degrees F to –30 degrees F.

08 7100-7

3. Spring power shall be continuously adjustable over the full range of closer sizes, and allow for reduced opening force for the physically handicapped. Hydraulic regulation shall be by tamper-proof, non-critical valves. Closers shall have separate adjustment for latch speed, general speed, and backcheck.

4. All closers shall have solid forged steel main arms (and forged forearms for parallel arm closers).

5. All surface mounted mechanical closers shall be certified to exceed ten million (10,000,000) full load cycles by a recognized independent testing laboratory.

6. Closers will have Powder coating finish certified to exceed 100 hours salt spray testing by ETL, an independent testing laboratory used by BHMA for ANSI certification.

7. Refer to door and frame details and furnish accessories such as drop plates, panel adapters, spacers and supports as required to correctly install door closers. State degree of door swing in the hardware schedule.

8. LCN Series as listed in sets.

I. Overhead Holders and Stops:

1. Type, function and fasteners must be same as Glynn-Johnson specified. Size per manufacturer's selector chart. Plastic end caps, hold open mechanisms and shock blocks are not allowed. End caps must be finished same as balance of unit.

2. Manufacture products using base material of Brass/Bronze for US3, US4, & US10B finished products and 300 Stainless Steel for US32 & US32D finished products.

3. Type, function, and fasteners must be the same as Glynn-Johnson specified. Size per manufacturer's selector chart.

a. Glynn-Johnson

J. Wall Stops:

1. Length to exceed projection of all other hardware. Provide with threaded studs and expansion shields for masonry wall construction. Install with slope at top.

a. Ives WS33(X)

b. BHMA L12011 or L12021

K. Thresholds:

1. 1/4" high - 5" wide. Cope at jambs.

2. Furnish full wall opening width when frames are recessed.

3. Cope in front of mullions if thresholds project beyond door faces.

4. Furnish with non-ferrous Stainless Steel Screws and Lead Anchors.

a. Zero as listed in sets

b. Equal of NGP or Reese

L. Door Sweeps:

1. Surface Sweeps:

a. Zero as listed in sets

b. Equal of NGP or Reese

M. Weather-stripping:

1. Apply to head and jamb stops.

08 7100-8

2. Solid Bar stock all sides

a. Zero as listed in sets

b. Equal of NGP or Reese

N. Miscellaneous:

1. Furnish items not categorized in the above descriptions but specified by manufacturer’s names in Hardware Sets.

O. Fasteners:

1. Furnish fasteners of the proper type, size, quantity and finish. Use machine screws and expansion shields for attaching hardware to concrete or masonry, and wall grip inserts at hollow wall construction. Furnish machine screws for attachment to reinforced hollow metal doors and frames and reinforced aluminum doors and frames. Furnish full thread wood screws for attachment to solid wood doors and frames. "TEK" type screws are not acceptable.

2. Sex bolts will not be permitted on reinforced metal doors or wood doors where blocking is specified.

2.3 Finishes:

A. Generally, Dull Chrome, US26D / BHMA 626. Provide finish for each item as indicated in sets.

2.4 Templates and Hardware Location:

A. Furnish hardware made to template. Supply required templates and hardware locations to the door and frame manufacturers.

B. Furnish metal template to frame/door supplier for continuous hinge.

C. Refer to Article 3.1 B.2, Locations, and coordinate with templates.

2.5 Cylinders and Keying:

A. All cylinders for this project will be supplied by one supplier regardless of door type and location.

B. The Finish Hardware supplier will meet with Architect and/or Owner to finalize keying requirements and obtain keying instructions in writing within one (1) month of receiving approved finish hardware submittal.

1. Supplier shall include the cost of this service in his proposal.

C. Provide a cylinder for all hardware components capable of being locked.

D. Provide cylinders master and grand master keyed to existing SFIC system according to Owner's instructions. Provide change keys, master keys and grand master keys as required by Owner.

E. Provide cylinders with construction cores or keying for use during the construction period.

When so directed, and in the presence of the Owner's security department or representative, convert construction cores or keying to the final system.

1. Supplier shall include the cost of this service in his proposal.

08 7100-9

PART 3 - EXECUTION

3.1 Installation

A. General:

1. Install hardware according to manufacturers installations and template dimensions.

Attach all items of finish hardware to doors, frames, walls, etc. with fasteners furnished and required by the manufacture of the item.

2. Provide blocking/reinforcement for all wall mounted Hardware.

3. Reinforced hollow metal doors and frames and reinforced aluminum door and frames will be drilled and tapped for machine screws.

4. Solid wood doors and frames: full thread wood screws. Drill pilot holes before inserting screws.

5. Continuous gear hinges attached to hollow metal doors and frames and aluminum doors and frames: 12-24 x 1/2" #3 Phillips Keenform self-tapping. Use #13 or 3/16 drill for pilot.

6. Continuous Gear Hinges require continuous mortar guards of foam or cardboard 1/2" thick x frame height, applied with construction adhesive.

7. Install weather-strip gasket prior to parallel arm closer bracket, rim exit device or any stop mounted hardware. Gasket to provide a continuous seal around perimeter of door opening. Allow for gasket when installing finish hardware. Door closers will require special templating. Exit devices will require adjustment in backset.

B. Locations:

1. Dimensions are from finish floor to center line of items.

2. Include this list in Hardware Schedule.

CATEGORY DIMENSION

Hinges Door Manufacturer's Standard Levers Door Manufacturer's Standard Exit Device Touchbar Per Template Offset Pulls Suitable for Exit Devices Wall Stops/Holders At Head Astragals Pull side of active leaf Trim Protector Bars Push side of door below lever handle Lock Protectors Pull side of door

C. Field Quality Inspection:

1. Inspect material furnished, its installation and adjustment, and instruct the Owner's personnel in adjustment, care and maintenance of hardware.

2. Locksets and exit devices shall be inspected after installation and after the HVAC system is in operation and balanced, to insure correct installation and proper operation.

3. Closers shall be inspected and adjusted after the HVAC system is in operation and balanced, to insure correct installation and proper operation.

4. A written report stating compliance, and also locations and kinds of noncompliance shall be forwarded to the Architect with copies to the Contractor, hardware distributor, hardware installer and building owner.

D. Technical and Warranty Information:

08 7100-10

1. At the completion of the project, the technical and warranty information coalesced and kept on file by the General Contractor/Construction Manager shall be given to the Owner or Owner’s Agent. In addition to both the technical and warranty information, all factory order acknowledgement numbers supplied to the General Contractor/Construction Manager during the construction period shall be given to the Owner or Owner’s Agent.

The warranty information and factory order acknowledgement numbers shall serve to both expedite and properly execute any warranty work that may be required on the various hardware items supplied on the project.

2. Submit to General Contractor/Construction Manager, two copies each of parts and service manuals and two each of any special installation or adjustment tools. Include for locksets, exit devices, door closers and any electrical products.

3.2 Hardware Sets:

Hardware Group No. 01

G104

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA STOREROOM LOCK 45H7D3J 626 BES

1 EA SURFACE CLOSER 4111 SHCUSH SRI 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

1 EA DOOR SWEEP 39A A ZER

1 EA THRESHOLD 545A-V3-223 A ZER

Hardware Group No. 02

E103A

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-98-NL-OP-110MD 626 VON

1 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SFIC RIM HOUSING 80-129 626 SCH

1 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4021 689 LCN

1 EA MOUNTING PLATE 4020-18G 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

08 7100-11

Hardware Group No. 03

E103C J105A J105B K105A K105B K106A

K106B

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-98-EO 626 VON

1 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4021 689 LCN

1 EA MOUNTING PLATE 4020-18G 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

Hardware Group No. 04

E103B

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA REMOVABLE MULLION KR4954 STAB 689 VON

1 EA PANIC HARDWARE CDSI-98-EO 626 VON

2 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4021 689 LCN

1 EA MOUNTING PLATE 4020-18G 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

Hardware Group No. 05

E103D E103E E103F

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA DUMMY PUSH BAR 350 626 VON

1 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4021 689 LCN

1 EA MOUNTING PLATE 4020-18G 689 LCN

08 7100-12

Hardware Group No. 06

J105C K105C K106C

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-98-NL-OP-110MD 626 VON

1 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SFIC RIM HOUSING 80-129 626 SCH

1 EA ELECTRIC STRIKE 6113 FSE DS 12/24 VAC/VDC 630 VON

1 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4021 689 LCN

1 EA MOUNTING PLATE 4020-18G 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

1 EA DOOR SWEEP 39A A ZER

1 EA THRESHOLD 545A-V3-223 A ZER

1 EA ACCESS CONTROL (RE-USE EXISTING)

PRESENTING AN AUTHORIZED CREDENTIAL WILL ENERGIZE THE ELECTRIC STRIKE AND

ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED.

COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE OWNER, THE

ARCHITECT AND ALL RELATED TRADES.

Hardware Group No. 07

H111A

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

1 EA REMOVABLE MULLION KR4854 STAB 689 VON

1 EA PANIC HARDWARE CDSI-98-EO 626 VON

1 EA PANIC HARDWARE CDSI-98-NL-OP-110MD 626 VON

3 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SFIC RIM HOUSING 80-129 626 SCH

1 EA ELECTRIC STRIKE 6113 FSE DS 12/24 VAC/VDC 630 VON

2 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

2 EA OH STOP 100S 630 GLY

2 EA SURFACE CLOSER 4021 689 LCN

2 EA MOUNTING PLATE 4020-18G 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

1 EA THRESHOLD 545A-V3-223 A ZER

1 EA ACCESS CONTROL (RE-USE EXISTING)

1 EA POWER SUPPLY PS902 900-2RS 120/240 VAC VON

PRESENTING AN AUTHORIZED CREDENTIAL WILL ENERGIZE THE ELECTRIC STRIKE AND

ALLOW ACCESS. FREE EGRESS IS ALWAYS ALLOWED.

COORDINATE SYSTEM OPERATION AND COMPONENT LOCATIONS WITH THE OWNER, THE

ARCHITECT AND ALL RELATED TRADES.

08 7100-13

Hardware Group No. 08

D107B E115A E117

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-98-EO 626 VON

1 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SURFACE CLOSER 4111 SCUSH 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

1 EA DOOR SWEEP 39A A ZER

THIS OPENING IS "EXIT ONLY".

Hardware Group No. 09

H111B

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

2 EA DUMMY PUSH BAR 350 626 VON

2 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

2 EA OH STOP 100S 630 GLY

2 EA SURFACE CLOSER 4021 689 LCN

2 EA MOUNTING PLATE 4020-18G 689 LCN

Hardware Group No. 10

D107A E106 E107 E121

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

1 EA REMOVABLE MULLION KR4954 STAB 689 VON

2 EA PANIC HARDWARE CDSI-98-EO 626 VON

3 EA SFIC MORTISE CYL. 80-102 626 SCH

2 EA SURFACE CLOSER 4111 SCUSH 689 LCN

1 EA MULLION SEAL 8780NBK PSA BK ZER

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

08 7100-14

Hardware Group No. 11

E104A F106B F106C

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

2 EA PANIC HARDWARE CDSI-3549A-EO-WH 628 VON

2 EA SFIC MORTISE CYL. 80-102 626 SCH

2 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

2 EA OH STOP 100S 630 GLY

2 EA SURFACE CLOSER 4011T 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

Hardware Group No. 12

E104B F106A F106D

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-3549A-EO-WH 628 VON

1 EA PANIC HARDWARE CDSI-3549A-NL-OP-388-WH 628 VON

2 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SFIC RIM HOUSING 80-129 626 SCH

2 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

2 EA OH STOP 100S 630 GLY

2 EA SURFACE CLOSER 4011T 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

Hardware Group No. 13

E115B

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

1 EA REMOVABLE MULLION KR4954 STAB 689 VON

2 EA PANIC HARDWARE CDSI-98-EO 626 VON

3 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SURFACE CLOSER 4111 EDA 689 LCN

1 EA SURFACE CLOSER 4111 SCUSH 689 LCN

1 EA WALL STOP WS33X 626 IVE

1 EA MULLION SEAL 8780NBK PSA BK ZER

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

08 7100-15

Hardware Group No. 14

G103

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

2 EA CONT. HINGE 112XY 628 IVE

1 EA REMOVABLE MULLION KR4954 STAB 689 VON

1 EA PANIC HARDWARE CDSI-98-EO 626 VON

1 EA PANIC HARDWARE CDSI-98-NL-OP-110MD 626 VON

3 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SFIC RIM HOUSING 80-129 626 SCH

2 EA 90 DEG OFFSET PULL 8190EZHD 12" O 630-

IVE

2 EA SURFACE CLOSER 4111 SCUSH 689 LCN

1 EA MULLION SEAL 8780NBK PSA BK ZER

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

2 EA DOOR SWEEP 39A A ZER

Hardware Group No. 15

G108

EACH TO HAVE:

QTY DESCRIPTION CATALOG NUMBER FINISH MFR

1 EA CONT. HINGE 112XY 628 IVE

1 EA PANIC HARDWARE CDSI-98-EO 628 VON

1 EA SFIC MORTISE CYL. 80-102 626 SCH

1 EA SURFACE CLOSER 4111 SCUSH SRI 689 LCN

1 SET WEATHER SEAL (BY DOOR & FRAME MFR)

1 EA DOOR SWEEP 39A A ZER

END OF SECTION

08 7100-16

11/24/20 CONSTRUCTION DOCUMENTS GLAZING

08 8000-1

SECTION 08 8000 - GLAZING

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Insulating glass.

B. Glazing compounds and accessories.

1.02 REFERENCE STANDARDS

A. 16 CFR 1201 - Safety Standard for Architectural Glazing Materials Current Edition.

B. ANSI Z97.1 - American National Standard for Safety Glazing Materials Used in Buildings -

Safety Performance Specifications and Methods of Test 2015.

C. ASCE 7 - Minimum Design Loads and Associated Criteria for Buildings and Other Structures

Most Recent Edition Cited by Referring Code or Reference Standard.

D. ASTM C864 - Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers 2005 (Reapproved 2015).

E. ASTM C1036 - Standard Specification for Flat Glass 2016.

F. ASTM C1048 - Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass

2018.

G. ASTM C1172 - Standard Specification for Laminated Architectural Flat Glass 2014.

H. ASTM C1193 - Standard Guide for Use of Joint Sealants 2016.

I. ASTM E1300 - Standard Practice for Determining Load Resistance of Glass in Buildings 2016.

J. ASTM E2190 - Standard Specification for Insulating Glass Unit Performance and Evaluation

2010.

K. GANA (GM) - GANA Glazing Manual 2008.

L. GANA (SM) - GANA Sealant Manual 2008.

M. GANA (LGRM) - Laminated Glazing Reference Manual 2009.

N. ICC (IBC) - International Building Code Most Recent Edition Adopted by Authority Having

Jurisdiction, Including All Applicable Amendments and Supplements.

O. IGMA TB-3001 - Guidelines for Sloped Glazing 2001.

P. IGMA TM-3000 - North American Glazing Guidelines for Sealed Insulating Glass Units for

Commercial & Residential Use 1990 (2016).

Q. NFPA 251 - Standard Methods of Tests of Fire Resistance of Building Construction and

Materials - 2006.

R. NFRC 100 - Procedure for Determining Fenestration Product U-factors 2017.

S. NFRC 200 - Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and

Visible Transmittance at Normal Incidence 2014, with Errata (2017).

T. NFRC 300 - Test Method for Determining the Solar Optical Properties of Glazing Materials and

Systems 2017.

1.03 ADMINISTRATIVE REQUIREMENTS

A. Preinstallation Meeting: Convene a preinstallation meeting one week before starting work of this section; require attendance by each of the affected installers.

1.04 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.

B. Product Data on Glazing. Provide structural, physical and environmental characteristics, size limitations, special handling and installation requirements.

C. Product Data on Glazing Compounds and Accessories: Provide chemical, functional, and environmental characteristics, limitations, special application requirements, and identify available colors.

D. Samples: Submit three samples 12 by 12 inch in size for each glass type.

08 8000-2

1. Non-insulated types may be 4 by 4 inches in size.

E. Certificate: Certify that products of this section meet or exceed specified requirements.

F. Warranty Documentation: Submit manufacturer warranty and ensure that forms have been completed in Owner's name and registered with manufacturer.

1.05 QUALITY ASSURANCE

A. Perform Work in accordance with GANA (GM), GANA (SM), GANA (LGRM), IGMA TM-3000, and IGMA TB-3001 for glazing installation methods.

B. Manufacturer Qualifications: Company specializing in manufacturing the products specified in this section with minimum 5 years of documented experience.

C. Installer Qualifications: Company specializing in performing work of the type specified and with at least 5 years documented experience.

1.06 FIELD CONDITIONS

A. Do not install glazing when ambient temperature is less than 40 degrees F.

B. Maintain minimum ambient temperature before, during and 24 hours after installation of glazing compounds.

1.07 WARRANTY

A. See Section 01 7800 - Closeout Submittals, for additional warranty requirements.

B. Insulating Glass Units: Provide a ten (10) year manufacturer warranty to include coverage for seal failure, interpane dusting or misting, including providing products to replace failed units.

C. Laminated Glass: Provide a ten (10) year manufacturer warranty to include coverage for delamination, including providing products to replace failed units.

D. Coated Glass: Provide a ten (10) year manufacturer warranty to include coverage for peeling, cracking, and other indications of deterioration in coating, including providing products to replace failed units.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Float Glass Manufacturers:

1. Guardian Glass, LLC: www.guardianglass.com.

2. Pilkington North America Inc: www.pilkington.com.

3. Viracon, Inc: www.viracon.com.

4. Vitro Architectural Glass (formerly PPG Industries, Inc.): www.vitroglazings.com.

5. Substitutions: Refer to Section 01 6000 - Product Requirements.

B. Laminated Glass Manufacturers:

1. Any of the manufacturers specified for float glass.

C. Insulating Glass Manufacturers:

1. Any of the manufacturers specified for float glass.

2.02 PERFORMANCE REQUIREMENTS

A. Exterior Glazing Assemblies:

1. Provide type and thickness of exterior glazing assemblies to support assembly dead loads, and to withstand live loads caused by positive and negative wind pressure acting normal to plane of glass.

a. Design Pressure: Calculated in accordance with ASCE 7 applicable codes, and as indicated on Drawings..

b. Comply with ASTM E1300 for design load resistance of glass type, thickness, dimensions, and maximum lateral deflection of supported glass.

1) Maximum Lateral Deflection: For glass supported on all four edges, limit center-of-glass deflection at design wind pressure to not more than 1/50 the short side length or 1 inch, whichever is less.

08 8000-3

c. Provide glass edge support system sufficiently stiff to limit the lateral deflection of supported glass edges to less than 1/175 of their lengths under specified design load.

d. Glass thicknesses listed are minimum.

2. Vapor Retarder and Air Barrier Seals: Provide completed assemblies that maintain continuity of building enclosure vapor retarder and air barrier.

a. In conjunction with vapor retarder and joint sealer materials described in other

Division 7 sections.

3. Thermal and Optical Performance: Provide exterior glazing products with performance properties as indicated. Performance properties are in accordance with manufacturer's published data as determined with the following procedures and/or test methods:

a. Center of Glass U-Value: Comply with NFRC 100 using Lawrence Berkeley National

Laboratory (LBNL) WINDOW 6.3 computer program.

b. Center of Glass Solar Heat Gain Coefficient (SHGC): Comply with NFRC 200 using

Lawrence Berkeley National Laboratory (LBNL) WINDOW 6.3 computer program.

c. Solar Optical Properties: Comply with NFRC 300 test method.

B. Probability of Breakage: Design glass for a probability of breakage not greater than 0.008 (8 lites per 1000) for glass not more than 15 degrees from vertical.

C. Differential Shading: Design glass to resist thermal stresses induced by differential shading within individual glass lites.

D. Insulating Glass:

1. Insulating Glass Certification Program: Provide insulating glass units that are certified by the Insulating Glass Certification Council (IGCC).

a. Provide permanent markings with appropriate certification label of IGCC on either the spacer or one lite of each insulated unit.

E. Safety Glazing:

1. Complies with ANSI Z97.1 and 16 CFR 1201; test requirements for Class A/Category II.

2. Markings for Safety Rated Glazing: Provide permanent markings on safety-rated glazing in compliance with applicable safety glazing standards, ICC (IBC), local building code, and authorities having jurisdiction.

F. Glass Thickness: Indicated glass thicknesses are minimums. Provide glass that complies with performance requirements and load designs, and is not less than the thickness indicated.

G. Glass Strength:

1. Where annealed float glass is indicated, provide annealed float glass, heat-strengthened float glass, or fully tempered float glass as needed to comply with performance requirements.

2. Where heat-strengthened float glass is indicated, provide heat-strengthened float glass or fully tempered float glass as needed to comply with performance requirements.

H. Glass Distortion Tolerances:

1. Roller Wave: Maximum 0.003 (0.076 mm) from peak to valley within the main body of the sheet and maximum 0.008 (0.2 mm) within 10.5 inches of a leading or trailing edge.

2. Localized Warp: Maximum 0.03 inch (0.8 mm) over any 12 inch (305 mm) span, but limited to 0.31 inch (8 mm).

2.03 FLOAT GLASS

A. Float Glass: Provide float glass based glazing unless otherwise indicated.

1. Annealed Type: ASTM C1036, Type I - Transparent Flat, Class 1 - Clear, Quality - Q3.

2. Kind HS - Heat-Strengthened Type: Complies with ASTM C1048.

3. Kind FT - Fully Tempered Type: Complies with ASTM C1048.

4. Fully Tempered Safety Glass: Complies with ANSI Z97.1 or 16 CFR 1201 criteria for safety glazing used in hazardous locations.

5. Tinted Type: ASTM C1036, Class 2 - Tinted, Quality - Q3, with color and performance characteristics as indicated.

08 8000-4

a. Glass Tints: Provide the following:

1) Color: Light Green.

(a) Basis-of-Design Product: PPG Solexia; Light Green, or a comparable product from any of the manufacturers specified for float glass.

2.04 LAMINATED GLASS

A. Laminated Glass: Float glass laminated in accordance with ASTM C1172.

1. Unless otherwise indicated laminate glass shall consist of two plies of clear annealed float glass with a polyvinyl butyral interlayer.

a. Minimum Thickness of Each Glass Ply: 1/8 inch (3 mm), unless otherwise indicated.

b. Polyvinyl Butyral (PVB) Interlayer: 0.060 inch thick, minimum, unless otherwise indicated.

1) Interlayer Color: white - to match Vanceva Artic Snow, unless otherwise indicated.

2.05 INSULATING GLASS

A. General: Unless otherwise noted, Insulating Glass Unit Types shall comply with the following:

1. Durability: Certified by an independent testing agency to comply with ASTM E2190.

2. Perimeter Spacer: Warm-edge spacer.

a. Manufacturer's standard low conductivity polymer, stainless steel, or hybrid material.

1) Spacer Color: Black.

2) Spacer Width: As required for specified insulating glass unit.

3) Products:

(a) Quanex IG Systems, Inc; Super Spacer Premium Enhanced:

www.quanex.com.

(b) Technoform Glass Insulation; TGI-Spacer: www.glassinsulation.us.

(c) Viracon, Inc; ExtremEdge: www.viracon.com.

(d) Vitro Architectural Glass (Formerly PPG); Intercept Spacer System:

www.vitroglazings.com.

(e) Substitutions: Refer to Section 01 6000 - Product Requirements.

3. Edge Seal:

a. Dual-Sealed System: Provide polyisobutylene or acrylic adhesive or spacer manufacturer's standard sealant as primary seal applied between spacer and glass panes, and butyl sealant as secondary seal applied around perimeter.

b. Color: Black.

4. Purge interpane space with dry air, hermetically sealed.

B. Type GL-6 - Insulating Glass Units: Vision glass, double glazed.

1. Applications: Exterior glazing unless otherwise indicated.

2. Space between lites filled with argon.

3. Outboard Lite: Fully tempered float glass, 1/4 inch thick, minimum.

a. Tint: Light Green.

4. Inboard Lite: Fully tempered float glass, 1/4 inch thick, minimum.

a. Tint: Clear.

5. Total Thickness: 1 inch.

6. Thermal Transmittance (U-Value), Summer - Center of Glass: 0.27, nominal.

7. Visible Light Transmittance (VLT): 61% percent, nominal.

8. Shading Coefficient: 0.37, nominal.

9. Solar Heat Gain Coefficient (SHGC): 0.32, nominal.

C. Type GL-9 - Insulating Glass Units: Spandrel glazing.

1. Applications: Exterior spandrel glazing unless otherwise indicated.

2. Space between lites filled with argon.

3. Outboard Lite: Fully tempered float glass, 1/4 inch thick, minimum.

a. Tint: Light Green.

08 8000-5

b. Coating: Same as on vision units, on #2 surface.

4. Inboard Lite: Fully tempered float glass, 1/4 inch thick.

a. Tint: Clear.

b. Opacifier: Ceramic frit, on #3 surface.

c. Opacifier Color: White.

5. Total Thickness: 1 inch.

6. Thermal Transmittance (U-Value), Summer - Center of Glass: 0.27, nominal.

D. Type GL-10 - Insulating Glass Units, laminated; IGMA TB-3001.

1. Applications: Clearstory windows.

2. Space between lites filled with argon.

3. Outboard Lite: Annealed float glass, 1/4 inch thick, minimum.

a. Tint: Light Green.

4. Laminated Inboard Lite, Outer Pane: Annealed float glass, 1/8 inch thick, minimum.

a. Tint: Clear.

5. Interlayer: Polyvinyl butyral (PVB); 0.060 inch thick.- white

6. Laminated Inboard Lite, Inner Pane: Annealed float glass, 1/4 inch thick, minimum.

a. Tint: Clear.

7. Total Thickness: 1 inch.

8. Thermal Transmittance (U-Value), Summer - Center of Glass: [_____], nominal.

E. Type GL-14 - 1” insulated metal panels: panels shall consist of a laminated sandwich of polyisocyanurate insulation core, 0.060 polyallomer substrate and smooth aluminum skins

0.021” thick minimum. The entire sandwich shall be bonded under heat and pressure with permanently elastic neoprene contact adhesive.

1. Panel Thickness: 1 inch unless indicated otherwise.

2. Color: PVDF/Kynar 500 to match adjacent framing.

3. Interior Finish: same as face sheet.

4. Manufacturer: Subject to compliance with requirements, provide Laminators Inc. “Thermo

Lite” System or approved equal.

2.06 ACCESSORIES

A. Setting Blocks: EPDM or neoprene, with 80 to 90 Shore A durometer hardness; ASTM C864

Option II. Length of 0.1 inch for each square foot of glazing or minimum 4 inch by width of glazing rabbet space minus 1/16 inch by height to suit glazing method and pane weight and area.

B. Spacer Shims: EPDM or neoprene, 50 to 60 Shore A durometer hardness; ASTM C864 Option

II. Minimum 3 inch long by one half the height of the glazing stop by thickness to suit application, self adhesive on one face.

C. Glazing Tape, Back Bedding Mastic Type: Preformed, butyl-based, 100 percent solids compound; 5 to 30 cured Shore A durometer hardness; coiled on release paper; black color.

1. Width: As required for application.

2. Thickness: As required for application.

D. Glazing Gaskets and Splines: Resilient EPDM or polyvinyl chloride extruded shape to suit glazing channel retaining slot; ASTM C864 Option II; color black.

E. Glazing Clips: Manufacturer's standard type.

PART 3 EXECUTION

3.01 VERIFICATION OF CONDITIONS

A. Verify that openings for glazing are correctly sized and within tolerances, including those for size, squareness, and offsets at corners.

08 8000-6

B. Verify that surfaces of glazing channels or recesses are clean, free of obstructions that may impede moisture movement, weeps are clear, and support framing is ready to receive glazing system.

C. Proceed with glazing system installation only after unsatisfactory conditions have been corrected.

3.02 PREPARATION

A. Clean contact surfaces with appropriate solvent and wipe dry within maximum of 24 hours before glazing. Remove coatings that are not tightly bonded to substrates.

B. Seal porous glazing channels or recesses with substrate compatible primer or sealer.

C. Prime surfaces scheduled to receive sealant where required for proper sealant adhesion.

3.03 INSTALLATION, GENERAL

A. Install glazing in compliance with written instructions of glass, gaskets, and other glazing material manufacturers, unless more stringent requirements are indicated, including those in glazing referenced standards.

B. Use one or more of the specified glazing methods as recommended by GANA, glass manufacturer, and installer, and as required to comply with performance requirements.

C. Install glazing sealants in accordance with ASTM C1193, GANA (SM), and manufacturer's instructions.

D. Do not exceed edge pressures around perimeter of glass lites as stipulated by glass manufacturer.

E. Set glass lites of system with uniform pattern, draw, bow, and similar characteristics.

F. Set glass lites in proper orientation so that coatings face exterior or interior as indicated.

G. Prevent glass from contact with any contaminating substances that may be the result of construction operations such as, and not limited to the following; weld splatter, fire-safing, plastering, mortar droppings, etc.

3.04 INSTALLATION - DRY GLAZING METHOD (TAPE AND GASKET SPLINE GLAZING)

A. Application - Exterior Glazed: Set glazing infills from the exterior of the building.

B. Cut glazing tape or spline to length; install on glazing pane. Seal corners by butting tape and sealing junctions with butyl sealant.

C. Place setting blocks at 1/4 points with edge block no more than 6 inch from corners.

D. Rest glazing on setting blocks and push against fixed stop with sufficient pressure to attain full contact.

E. Install removable stops without displacing glazing spline. Exert pressure for full continuous contact.

F. Carefully trim protruding tape with knife.

3.05 CLEANING

A. Remove excess glazing materials from finish surfaces immediately after application using solvents or cleaners recommended by manufacturers.

B. Remove non-permanent labels immediately after glazing installation is complete.

C. Clean glass and adjacent surfaces after sealants are fully cured.

D. Clean glass on both exposed surfaces not more than 4 days prior to Date of Substantial

Completion in accordance with glass manufacturer's written recommendations.

3.06 PROTECTION

A. Remove and replace glass that is damaged during construction period prior to Date of

Substantial Completion.

3.07 GLASS SCHEDULE

A. GL-6: Low-E-coated, tinted, insulating safety glass

08 8000-7

1. Overall Unit Thickness: 1 inch.

2. Outdoor Lite: Tinted fully tempered float glass.

a. Minimum Thickness: 1/4 inch (6 mm).

b. Tint Color: Light Green.

3. Airspace:

a. Width: 1/2 inch.

b. Interspace Content: Argon.

4. Indoor Lite: Clear fully tempered float glass.

a. Minimum Thickness: 1/4 inch (6 mm).

b. Low-E Coating: On 3rd surface.

5. Safety glazing required.

6. Performance:

a. Winter Nighttime U-Factor: 0.28 maximum.

b. Visible Light Transmittance: 32 percent minimum.

c. Solar Heat Gain Coefficient: 0.24 maximum.

B. GL-9: Low-E-coated, tinted insulating spandrel glass.

1. Overall Unit Thickness: 1 inch.

2. Outdoor Lite: Tinted tempered float glass.

a. Minimum Thickness: 1/4 inch (6 mm).

b. Tint Color: Light Green.

3. Airspace:

a. Width: 1/2 inch.

b. Interspace Content: Argon.

4. Indoor Lite: Clear tempered float glass.

a. Minimum Thickness: 1/4 inch (6 mm).

b. Low-E Coating: On 3rd surface.

c. Silicone-coated Spandrel Coating: On 4th surface.

5. Performance:

a. Winter Nighttime U-Factor: 0.28 maximum.

C. Type GL-10 - Insulating Glass Units, laminated; IGMA TB-3001.

1. Applications: Clearstory windows.

2. Space between lites filled with argon.

3. Outboard Lite: Annealed float glass, 1/4 inch thick, minimum.

a. Tint: Light Green.

b. Coating: Self-cleaning type, on #1 surface.

c. Coating: Low-E (passive type), on #2 surface.

4. Laminated Inboard Lite, Outer Pane: Annealed float glass, 1/8 inch thick, minimum.

a. Tint: Clear.

5. Interlayer: Polyvinyl butyral (PVB); 0.060 inch thick. - white to match Vanceva Artic Snow 0.060”

6. Laminated Inboard Lite, Inner Pane: Annealed float glass, 1/8 inch thick, minimum.

7. Tint: Clear.

8. Total Thickness: 1 inch.

9. Safety glazing required.

10. Performance:

a. Winter Nighttime U-Factor: 0.28 maximum.

08 8000-8

D. Type GL-14 insulated metal panel

1. Thickness: 1”

2. Color: Match adjacent storefront framing

11/24/20 CONSTRUCTION DOCUMENTS NON-STRUCTURAL METAL FRAMING

09 2216-1

SECTION 09 2216 - NON-STRUCTURAL METAL FRAMING

1.01 SECTION INCLUDES

A. Metal non-load-bearing interior partition, ceiling, and soffit framing.

B. Suspension systems for interior ceilings and soffits.

C. Framing accessories.

1.02 REFERENCE STANDARDS

A. AISI S100-12 - North American Specification for the Design of Cold-Formed Steel Structural

Members 2012.

B. ASTM A641/A641M - Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire

2019.

C. ASTM A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or

Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process 2020.

D. ASTM B633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel

2019.

E. ASTM C645 - Standard Specification for Nonstructural Steel Framing Members 2018.

F. ASTM C754 - Standard Specification for Installation of Steel Framing Members to Receive

Screw-Attached Gypsum Panel Products 2020.

G. ASTM C840 - Standard Specification for Application and Finishing of Gypsum Board 2020.

H. ASTM C955 - Standard Specification for Cold-Formed Steel Structural Framing Members

2018, with Editorial Revision.

I. ASTM D3575 - Standard Test Methods for Flexible Cellular Materials Made From Olefin

Polymers.

J. ASTM E119 - Standard Test Methods for Fire Tests of Building Construction and Materials

2020.

K. ASTM E90 - Standard Test Method for Laboratory Measurement of Airborne Sound

Transmission Loss of Building Partitions and Elements 2009 (Reapproved 2016).

L. ASTM E413 - Classification for Rating Sound Insulation 2016.

M. ASTM F1941/F1941M - Standard Specification for Electrodeposited Coatings on Mechanical

Fasteners, Inch and Metric 2016.

N. ASTM F593 - Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

2017.

O. ASTM F594 - Standard Specification for Stainless Steel Nuts 2009 (Reapproved 2020).

P. GA-216 - Application and Finishing of Gypsum Panel Products 2016.

Q. GA-600 - Fire Resistance Design Manual 2015.

R. ICC-ES AC193 - Acceptance Criteria for Mechanical Anchors in Concrete Elements 2015.

S. ICC-ES AC308 - Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete

Elements 2016.

T. UL (FRD) - Fire Resistance Directory Current Edition.

1.03 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements for submittal procedures.

B. Shop Drawings:

1. Indicate component details, stud layout, framed openings, anchorage to structure, acoustic details, type and location of fasteners, accessories, and items of other related work.

2. Describe method for securing studs to tracks, splicing, and for blocking and reinforcement of framing connections.

09 2216-2

C. Product Data: Provide data describing framing member materials and finish, product criteria, load charts, and limitations.

D. Product Data: Provide manufacturer's data on partition head to structure connectors, showing compliance with requirements.

E. Manufacturer's Qualification Statement.

F. Installer's Qualification Statement.

1.04 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in performing work of type specified and with at least five years of documented experience.

B. Installer Qualifications: Company specializing in performing the work of this section with minimum five years documented experience and approved by manufacturer.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Metal Framing, Shaft Wall Framing, Connectors, and Accessories:

1. ClarkDietrich Building Systems: www.clarkdietrich.com.

2. Jaimes Industries Inc.: www.jaimesind.com.

3. MarinoWARE: www.marinoware.com.

4. MBA Building Supplies, Inc.: www.mbastuds.com.

5. State Building Products; www.statebp.com.

6. The Steel Network, Inc: www.SteelNetwork.com.

7. Steel Stud Solutions, LLC; www.steelstudsolutions.com.

8. Telling Industries; www.buildstrong.com.

9. Substitutions: See Section 01 6000 - Product Requirements.

2.02 PERFORMANCE REQUIREMENTS

A. Provide completed assemblies complying with ASTM C840 and GA-216.

B. Fire-Rated Assemblies: For fire-resistance-rated assemblies that incorporate non-load-bearing steel framing, provide materials and construction identical to those tested in assembly indicated, according to ASTM E119 and as follows:

1. Provide construction equivalent to one of the following:

a. UL Assembly Numbers: Provide construction equivalent to that listed for the particular assembly in the current UL (FRD).

b. Gypsum Association File Numbers: Provide construction complying with requirements of GA-600 for the particular assembly.

C. STC-Rated Assemblies: For STC-rated assemblies, provide materials and construction identical to those tested in assembly indicated on Drawings, calculated in accordance with

ASTM E413, based on tests conducted in accordance with ASTM E90.

D. Shaft Walls: Provide completed assemblies with the following characteristics:

1. Comply with requirements of Fire-Rated Assemblies.

2. Shaft Walls at HVAC Shafts: Provide completed assemblies with the following characteristics:

a. Air Pressure Within Shaft: Sustained loads of 7.5 lbf/sq ft with maximum mid-span deflection of L/240; unless otherwise indicated.

b. Acoustic Attenuation: STC of 40-44 calculated in accordance with ASTM E413, based on tests conducted in accordance with ASTM E90; unless otherwise indicated.

E. Horizontal Deflection: For wall assemblies, limit maximum deflection of wall framing to L/240 at

5 psf .

1. Exception: Limit deflection of walls to receive hard tile surfaces to L/360 at 5 psf.

F. Protective Coatings: Equivalent (EQ) coatings are not acceptable; products shall be hot-dip galvanized as indicated.

09 2216-3

G. Embossed (equivalent thickness) steel framing products are not acceptable; products shall be in steel thicknesses indicated.

2.03 FRAMING MATERIALS

A. Non-Loadbearing Framing System Components: ASTM C645; galvanized sheet steel, of size and properties necessary to comply with ASTM C754 for the spacing indicated.

1. Protective Coating: ASTM A653/A653M, G40, hot-dip galvanized.

2. Minimum Metal Thickness: 0.0329 inch (20 gage).

3. Framing Depths: As indicated.

4. Profiles:

a. Studs: C shaped with flat or formed webs.

b. Runners: U shaped, sized to match studs.

1) Where indicated or required, provide slip-type head joints using slotted deflection track.

c. Ceiling Channels: C shaped.

d. Furring: Hat-shaped sections, minimum depth of 7/8 inch.

B. Slotted Deflection Track: Provide galvanized sheet steel track with slotted holes in flanges for mechanical anchorage of studs that accommodate deflection; provide screws and anti-friction bushings. Slotted connections prevent stud rotation without use of lateral bracing and maintains structural performance of partition.

1. Provide at partition heads to structure connections.

2. Shall prevent cracking of finishes applied to interior partition framing resulting from deflection of structure above

3. Structural Performance: Maintain lateral load resistance and vertical movement capacity required by applicable code, when evaluated in accordance with AISI S100-12.

4. Comply with ASTM C645 and ASTM C754.

5. Protective Coating: ASTM A653/A653M, G40, hot-dip galvanized.

6. Minimum Metal Thickness: Same material thickness as studs.

7. Track Depth: Matching studs.

8. Provide components UL-listed for use in UL-listed fire-resistance-rated head of partition joint systems indicated on drawings.

a. At Contractor's option, provide the following:

1) Slotted Deflection and Firestop Track: Similar to standard slotted deflection track specified, but includes intumescent strip factory-applied to track flanges or web that expands when exposed to heat or flames to provide a perimeter joint seal.

(a) Products:

(1) ClarkDietrich Building Systems; BlazeFrame Firestop Deflection Track : www.clarkdietrich.com.

(2) MarinoWARE; FAS Track 1000: www.marinoware.com.

(3) Substitutions: See Section 01 6000 - Product Requirements.

C. Preformed Top Track Firestop Seal: Pre-formed firestop device field-applied to head of top track that expands when exposed to heat or flames to provide a perimeter joint seal.

1. At Contractor's option provide preformed top track firestop seals instead of traditional perimeter joint seals.

2. Provide components UL-listed for use in UL-listed fire-resistance-rated head of partition joint systems indicated on drawings.

3. Products:

a. Hilti, Inc; Top Track Seal CFS TTS: www.us.hilti.com.

b. Substitutions: See Section 01 6000 - Product Requirements.

D. Resilient Furring Channels: Galvanized sheet steel, single leg, asymmetrical channel, 1/2 inch deep with a 1-1/4 inch screw flange; complying with ASTM C645.

1. Exception: At ceilings provide double leg, symmetrical channels.

2. Protective Coating: ASTM A653/A653M, G40, hot-dip galvanized.

09 2216-4

3. Minimum Metal Thickness: 0.0179 inch (25 gage).

E. Z-shaped Furring: Galvanized sheet steel z-shaped furring, 2 inches deep, unless otherwise indicated; complying with ASTM C645.

1. Protective Coating: ASTM A653/A653M, G40, hot-dip galvanized.

2. Minimum Metal Thickness: 0.0312 inch (20 gage).

2.04 FRAMING ACCESSORIES

A. Bridging and Bracing Members: Of same material as studs; thickness to suit purpose;

complying with applicable requirements of ASTM C754.

1. Steel, 0.0538-inch (1.37mm) minimum base-metal thickness, with a minimum 1/2-inch (13mm) wide flanges.

a. Basis-of-Design Product: Subject to compliance with requirements, provide

ClarkDietrich Systems Spazzer 9200 Bridge and Spacing Bar, or equivalent.

B. Backing Plates: 0.064 inch thick (16 gage), galvanized.

C. Wood Blocking: Refer to Section 06 1000 - Rough Carpentry.

D. Anchorage Devices: Powder actuated or Drilled expansion bolts.

E. Acoustic Sealant: As specified in Section 09 2900 - Gypsum Board.

F. Isolation Strip: Foam gasket, ASTM D3575, closed-cell vinyl foam strips, 1/8 inch thick, in width to suit steel stud size.

1. Manufacturer:

a. Williams; Everlastic EVA 200; www.williamsproducts.net.

b. Substitutions: See Section 01 6000 - Product Requirements.

2.05 SUSPENSION SYSTEMS

A. Carrying Channels: ASTM C955; cold-rolled galvanized steel sheet U-channel.

1. Protective Coating: ASTM A653/A653M, G40, hot-dip galvanized.

2. Minimum Metal Thickness: 0.064 inch (16 gage).

3. Depth: 2 inches unless otherwise indicated.

B. Furring Channels:

1. Hat-Shaped, Rigid Furring Channels: As specified in "Framing Materials" above.

2. Resilient Furring Channels: As specified in "Framing Materials" above.

C. Tie Wire: ASTM A641/A641M, Class 1 zinc coating, soft temper, 0.062-inch (16 gage) diameter or double strand of 0.048-inch (18 gage) diameter wire.

D. Wire Hangers: ASTM A641/A641M, Class 1 zinc coating, soft temper, 0.16 inch (8 gage) diameter.

E. Hanger Attachments to Concrete:

1. Expansion Anchors: Fastener systems with evaluations based on ICC-ES AC193.

2. Adhesive Anchors: Fastener systems with evaluations based on ICC-ES AC308.

3. Material for Interior Locations: Carbon-steel components zinc-plated to comply with ASTM

B633 or ASTM F1941/F1941M, Class Fe/Zn 5, unless otherwise indicated.

4. Material for Exterior Locations and Interior Wet/Humid Locations: Alloy Group 1 (A1) stainless-steel bolts, ASTM F593, and nuts, ASTM F594.

F. Grid Suspension System for Gypsum Board Ceilings: ASTM C645, direct-hung system composed of main beams and cross-furring members that interlock.

1. At Contractor's option provide grid suspension system instead of traditional carrying and furring channels.

2. Not permitted for multi-layer gypsum board systems.

3. Manufacturers:

a. Armstrong World Industries, Inc.; Drywall Grid…