Attachment_6_Design Addendum No. 1.pdf

10 February 2026

4219 WOODWARD AVE, SUITE 301, DETROIT, MI 48201 313.462.2550 | WWW.QUINNEVANS.COM

WASHINGTON, DC | ANN ARBOR, MI | BALTIMORE, MD | DETROIT, MI | MADISON, WI | RICHMOND, VA

ADDENDUM NO. 1

Project: ST MAR’S COLLEGE OF MARYLAND

LANDERS LIBRARY LIBRARY RENOVATION

Bid Package ref: CONSTRUCTION DOCUMENTS - APRIL 30, 2025

1.1 PROJECT INFORMATION

A. Project Name: ST MAR’S COLLEGE OF MARYLAND – LANDERS LIBRARY

B. Owner: St. Mary’s College of Maryland

C. Architect: Quinn Evans

1.2 NOTICE TO BIDDERS

A. This Addendum serves to clarify, revise, and supersede information in the Project Manual, Drawings, and previously issued Addenda. Portions of the Addendum affecting the Contract Documents will be incorporated into the Contract by enumeration of the Addendum in the Owner/Contractor Agreement.

B. The bidder shall acknowledge receipt of this addendum in their proposal at the designated location on the Proposal Form, or their Proposal Cover if no form is defined.

1.3 ATTACHMENTS

A. Responses to Contractor/Bidder Requests for Information:

None

B. Drawings:

This Addendum includes the following revised or new drawings issued in their entirety. Drawings are clouded, identified with mark, and dated to correspond with this Addendum.

The following list includes a brief summary of revisions.

1. Architectural Drawings:

1. AD101 DEMO PLAN – FIRST FLOOR

a) KEYNOTE d10.6 ADDED

2. A432 INTERIOR ELEVATIONS

a) Note added to elevation B4

3. A433 INTERIOR ELEVATIONS

a) Note added to elevation B4

4. A703 FURNITRE & EQUIPMENT PLAN – L2 WEST

a) Sheet note 2 added

b) Keynote legend added

C. Specifications:

This Addendum includes the following revised or new specification sections issued in their entirety as attachments dated to correspond with this Addendum.

Revised sections strike out revised text with revisions text appearing bold typical.

1. SECTION 10 1423 PANEL SIGNAGE

2. SECTION 10 1100 VISUAL DISPLAY DEVICES

END OF ADDENDUM

http://www.quinnevans.com/

St. Mary's College of Maryland Landers Library Renovation

February 10, 2026 QE Project # 42137280

101100 Visual Display Units - 1

SECTION 101100

VISUAL DISPLAY UNITS

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Glass markerboards.

1.02 REFERENCE STANDARDS

A. 16 CFR 1201 - Safety Standard for Architectural Glazing Materials; Current Edition.

B. ANSI Z97.1 - American National Standard for Safety Glazing Materials Used in Buildings -

Safety Performance Specifications and Methods of Test; 2015 (Reaffirmed 2020).

C. ASTM C1172 - Standard Specification for Laminated Architectural Flat Glass; 2019.

1.03 SUBMITTALS

A. See Section 013000 - Administrative Requirements, for submittal procedures.

B. Product Data: Provide manufacturer's data on chalkboard, porcelain enamel steel markerboard, glass markerboard, tackboard, tackboard surface covering, trim, and accessories.

1.04 QUALITY ASSURANCE

PART 2 PRODUCTS

2.01 VISUAL DISPLAY UNITS

A. Magnetic Glass Markerboards:

1. Manufacturers:

a. Claridge Products and Equipment, Inc: www.claridgeproducts.com/#sle.

b. Substitutions: See Section 016000 - Product Requirements.

2. Glass: Laminated, low iron, 1/4 inch thick (6 mm thick), with bevel edges and radiused corners, laminated to steel backing sheet for use with magnets. Coated or treated for use as dry erase board or projection surface.

3. Glass Finish: As selected from manufacturer's full range.

4. Steel Backing Sheet Thickness: 24 gauge, 0.0239 inch (0.61 mm).

5. Size: As indicated on drawings.

6. Frame: No frame, with concealed fasteners.

7. Mounting: Concealed Z clips.

8. Accessories: Provide magnetic marker tray and magnetic marker holder.

2.02 MATERIALS

A. Float Glass: Provide float-glass-based glazing unless otherwise indicated.

1. Fully Tempered Safety Glass: Comply with ANSI Z97.1 or 16 CFR 1201 criteria for safety glazing used in hazardous locations.

B. Laminated Glass: Float glass laminated in accordance with ASTM C1172.

1. Laminated Safety Glass: Comply with ANSI Z97.1 - Class B or 16 CFR 1201 - Category I impact test requirements.

END OF SECTION

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 1

SECTION 101400

PANEL SIGNAGE

PART 1 – GENERAL

1.01 DESCRIPTION

A. This section specifies interior identification, informational, directional signs, and directories.

1.02 SUBMITTALS

A. Samples: Submit one full size sample sign of the type, style, and color specified including method of attachment. If approved, the sample will become a part of the job.

B. Manufacturer’s Literature: Manufacturer’s printed specifications, mounting details, installation, and maintenance drawings.

C. Shop Drawings: Scaled for manufacturer and fabrication of sign types. Identify materials, size, typography, artwork, finishes, mounting, and accessory items.

1.03 DELIVERY AND STORAGE

A. Package to prevent damage or deterioration during shipment, handling, storage, and installation. Maintain protective coverings in place and in good repair until removal is necessary. Store products in dry condition inside enclosed facilities.

B. Deliver signs only when mounting surfaces are ready for installation work to proceed.

1.04 EXTRA MATERIALS

A. Expedited Sign Maintenance Program: Coupon books for redemption of expedited replacement Inserts and additional signage.

1.05 REFERENCES

A. Publications listed below form a part of this specification to extent referenced. Publications are referenced in text by basic designation only.

1. American National Standards Institute (ANSI) • Federal Specifications

2. American Society for Testing & Materials (ASTM) • Uniform Sign Code

1.06 WARRANTY

A. Provide manufacturer’s warranty against defect in materials. Warranty shall provide material and labor to repair or replace defective materials at the manufacturer’s discretion. Damage caused by physical or chemical abuse or damage from excessive heat will not be warranted.

Removal and reinstallation of existing signage is not warranted.

PART 2 – PRODUCTS

2.01 GENERAL

2.02 REFERENCE STANDARDS

A. UL 94 - Tests for Flammability of Plastic Materials for Parts in Devices and Appliances; Current Edition, Including All Revisions.

B. Sign and graphic components are to be by a single manufacturer, including necessary mounting options, fittings, and fastenings.

2.03 SIGN STANDARDS

A. SIGN TYPE

1. Sign Type/Part No.: Sign Type 1 (Classroom), Sign Type 2 (Office), Sign Type 3 (Permanent Rooms), Sign Type 7 (Evacuation Plan), Sign Type Elevator Flag, Sign Type Restroom Flag, Sign Type Directory with Map, Sign Type Large Wayfinding, Sign Type Small Wayfinding.

2. End Cap Style: Square Corner (SC).

3. End Cap Color: Charcoal (184)

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 2

4. Mounting Option: Screw (D) or Adhesive (A), glass mounted signage to be mounted with Vinyl Glass Backers.

5. Insert Size: per plan pages.

6. Insert Color: Clear Maple (305), Charcoal (184), Pewter (154), Oyster (732).

7. Accents, Top / Bottom Trim: Accent Strip (AS) 184 Charcoal.

8. Finishes are to meet current Federal ADA and State requirements.

B. TYPOGRAPHY

1. Copy Option: ADA Direct Print (ADP), Direct Print (D2S) Laser Print (LP).

2. Copy Color: Charcoal (184), Oyster (732), Black (704).

3. Copy Style: Helvetica Regular (HRC)

4. Copy Size: Various sizing, minimum 5/8” for ADA copy, 4” Symbols.

5. Copy Position: Left Justified, Centered, and Right Justified.

6. Copy Case: All Caps (AC)

C. Note: All ADA options are standard All Caps to be compliant.

1. Copy shall be a true, clean accurate reproduction of typeface(s) specified.

2. Letter spacing and in-between line spacing shall be set by manufacturer.

3. Arrows, symbols, and logo art: To be provided in style, sizes, colors, and spacing as shown in drawings.

4. Braille: Grade 2

5. Translations: Grade 2 Braille copy, as noted in Sign Message Schedule, is responsibility of the sign manufacturer. Any second language text, as noted in Sign Message Schedule, is responsibility of the customer.

2.04 SIGN TYPES

A. General:

B. Provide products produced by 2/90 Sign Systems, 5350 Corporate Grove Blvd SE, Grand

Rapids, MI 49512, phone 800.777.4310, fax 616.656.4300.

C. Sign Type/Part No.:

1. SLIDE: Sign Type 1 (Classroom), Sign Type 2 (Office), Sign Type 3 (Permanent Rooms), Sign Type 7 (Evacuation Plan), Sign Type Elevator Flag, Sign Type Restroom Flag, Sign Type Directory with Map, Sign Type Large Wayfinding, Sign Type Small Wayfinding.

2. PLAQUES: Sign Type 4A (Men’s Restroom), Sign Type 4D (Women’s Restroom), Sign Type Stair ID, Sign Type 6 (In Case of Fire), Sign Type 11 (Max Occupancy), Sign Type Stairwell, Sign type Elevator ID, Sign Type Info/Exit, Sign Type 1G,

3. VINYL GLASS BACKERS: provided for signs applied to glass.

D. SLIDE MODULAR SIGN SYSTEM

1. The 2/90 Interchangeable Component Sign System shall be comprised of three primary components: Structural Rail, Copy Insert(s), and Interlocking End Caps or Frame.

2. Interior sign system is capable of being arranged in a variety of configurations with a minimum of attachments, devices, and connectors.

3. Interchangeable nature of the system will allow for changes of graphic components of the installed sign, without changing sign in its entirety.

4. Slide is available in two thicknesses. Standard profile is 9/16” and can accept Inserts on both sides. Thin profile is 9/32” and can only accept Inserts on one side. Thin and Standard Profiles are used in this project.

5. Slide shall allow for different mounting devices including adhesive tape, magnetic tape, hook and loop, screw, pin, freestanding, various panel hooks and ceiling options, and other mounting devices as specified. Screw (D), Adhesive (A), Perpendicular (K)

6. STRUCTURAL RAIL

a. Structural Rail utilizes horizontal rails, spaced to allow uniform, modular sizing of

Inserts. It is the internal structural member of the sign in extruded 6063-TS aluminum, anodized black.

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 3

b. The Structural Rail may accept an ABS plastic, anodized aluminum, high-pressure laminate, or acrylic Insert on one or both sides, depending upon sign style.

c. Structural Rail shall allow for different mounting devices including wall mounting for screw-on applications, pressure sensitive tape, freestanding mount, fabric panel mount, ceiling mount, and other mounting devices as specified. Screw (D), Adhesive (A), Perpendicular (K).

d. Structural Rails can be converted in the field to permit a sign to be enlarged from one size to another, in height or width.

e. Rail Joiners extruded in black PVC plastic. Rail Joiners connect Structural Rails together providing a butt joint along their edges; Rail Joiners are not visible in rail assembly.

f. Accent Strips extruded in 6063-T5 aluminum also connect Structural Rails together but with a visible horizontal rib, which is seen between the adjacent Copy Inserts.

Accent Strips are satin anodized and can be color matched in painted acrylic lacquer. Accent Strip (AS) Charcoal (184)

7. COPY INSERTS

8. Copy Inserts accept various forms of copy and graphics and attach to the Structural Rail with a hook detail.

a. Copy Inserts are interchangeable by sliding horizontally from either side of sign, and to other signs in system of equal width or height.

b. Wipe clean with a damp cloth. Do not use harsh chemicals or solvents.

c. Copy Insert Materials:

1) ABS Inserts – .090” extruded ABS plastic core with .003” UV resistant acrylic cap bonded during extrusion/texturing process. Pressure bonded to extruded PVC hook using high-bond, pressure sensitive adhesive. Insert color is either integral or painted in acrylic lacquer. Finished in a Chromium industries #HM335RA texture pattern to prevent glare and disguise fingerprints.

2) Window Inserts – Extruded 6063-T5 aluminum with integral hooks for connection to Structural Rail. Color is anodized black, anodized satin, or painted acrylic lacquer. Inserts hold die-cut paper insert with a clear .020” textured polycarbonate lens.

3) ADA, Direct Print Tactile Inserts – UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2 Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

9. INTERLOCKING END CAPS OR FRAMES

a. End Caps interlock to Structural Rail with steel spring clips to form an integral unit, enclosing and securing the changeable Copy Inserts, without requiring tools for assembly.

b. End Caps or Frames are extruded in 6063-T5 extruded aluminum or injection molded ABS. Painted with acrylic lacquer.

c. Interchangeable to either end of sign and to other signs in the system of equal height.

d. Tamper-resistant feature can be added for Thin profile by notching structural rail to accept locking tab in End Cap clip or by use of screws for Standard profile.

e. SPEC WRITER NOTE: Square Corner (SC) Charcoal (184)

10. GRAPHIC PROCESS

a. Type and symbols are to be produced in the following manner:

1) Direct Print Copy – VOC free, ultra-violet cured inks digitally applied directly to the substrate surface. SPEC WRITER NOTE: only available in matte finish. i.e.

715 Yellow is matte.

2) Laser Print Copy – Computer generated graphics laser printed on die-cut paper Insert.

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 4

3) ADA, Direct Print Tactile Copy – UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2 Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

b. TYPOGRAPHY

1) Copy Option: ADA Direct Print (ADP), Direct Print (DP), Laser Print (LP)

2) Copy Color: Charcoal (184), Oyster (732), Black (704)

3) Copy Style: Helvetica Regular

4) Copy Size: Various sizing, minimum 5/8” for ADA copy, 4” Symbols.

5) Copy Position: Left Justified, Centered, and Right Justified.

6) Copy Case: All Caps (AC)

c. Note: All ADA options are standard All Caps to be compliant.

1) Copy shall be a true, clean accurate reproduction of typeface(s) specified.

2) Letter spacing and in-between line spacing shall be set by manufacturer.

3) Arrows, symbols, and logo art: To be provided in style, sizes, colors and spacing as shown in drawings.

4) Braille: Grade 2

5) Translations: Grade 2 Braille copy, as noted in Sign Message Schedule, is responsibility of the sign manufacturer. Any second language text, as noted in Sign Message Schedule, is responsibility of the customer.

E. PLAQUES

1. A Plaque is the Copy Insert material of the 2/90 Slide Modular Sign minus the leg configuration needed to attach to the Structural Rail.

2. Plaques are not changeable.

3. Plaques shall allow for different mounting devices including pressure sensitive tape, magnetic tape, panel and tile, hook, and other mounting devices as specified. Adhesive

(A) is to be used in this project.

4. Wipe clean with a damp cloth. Do not use harsh chemicals or solvents.

5. PLAQUE MATERIALS:

a. ABS Plaque - .090” extruded ABS plastic core with .003” UV resistant acrylic cap bonded during extrusion/texturing process. Plaque color is either integral or painted in acrylic lacquer. Finished in a Chromium industries #HM335RA texture pattern to prevent glare and disguise fingerprints.

b. ADA, Direct Print Tactile Plaque – UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2 Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

6. GRAPHIC PROCESS

a. Type and symbols are to be produced in the following manner:

1) Direct Print Copy – VOC free, ultra-violet cured inks digitally applied directly to the substrate surface.

2) ADA, Direct Print Tactile Copy – UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2 Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

b. TYPOGRAPHY

1) Copy Option: SPEC WRITER NOTE: List Copy Option. i.e. Direct Print (DP)

2) Copy Color: SPEC WRITER NOTE: List Copy Color. i.e. White (708)

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 5

3) Copy Style: SPEC WRITER NOTE: List Copy Style. i.e. Arial (ARL)

4) Copy Size: SPEC WRITER NOTE: List Copy Size. i.e. 5/8

5) Copy Position: SPEC WRITER NOTE: List Copy Position. i.e. Center (C)

6) Copy Case: SPEC WRITER NOTE: Standard Upper and Lower Case unless specified All Caps or As Typed indicated in the Sign Message Schedule. i.e. All Caps (AC)

c. Note: All ADA options are standard All Caps to be compliant.

1) Copy shall be a true, clean accurate reproduction of typeface(s) specified.

2) Letter spacing to be normal and interline spacing shall be set by manufacturer.

3) Arrows, symbols, and logo art: To be provided in style, sizes, colors, and spacing as shown in drawings.

4) Braille: Grade 2

5) Translations: Grade 2 Braille copy, as noted in Sign Message Schedule, is responsibility of the sign manufacturer. Any second language text, as noted in Sign Message Schedule, is responsibility of the customer.

2.05 FABRICATION

A. Design components allow for expansion and contraction for a minimum material temperature range of 56 degrees C 100 degrees Fahrenheit (37.78 degrees Celsius), without causing buckling, excessive opening of joints, or over stressing of adhesives and fasteners.

B. Form work to required shapes and sizes, with true curves, lines, and angles. Provide necessary rebates, lugs, and brackets for assembly of units.

C. Contact surfaces of connected members must be true. Assembled so joints will be tight and practically unnoticeable, without use of filling compound.

D. Signs shall have fine, even texture and be flat and sound. Lines and miters sharp, arises unbroken, profiles accurate and ornament true to pattern. Plane surfaces should be smooth, flat and without oil-canning, free of rack and twist. Maximum variation from plane of surface plus or minus .032”. Restore texture to filled or cut areas.

E. Level or straighten wrought work. Members shall have sharp lines and angels and smooth surfaces.

F. Extruded members to be free from extrusion marks. Square turns and corners sharp, curves true.

G. Conceal fastenings where possible. Exposed ends and edges mill smooth, with corners slightly rounded.

H. All painted surfaces properly primed. Finish coating of paint to have complete coverage with no light or thin applications allowing substrate or primer to show. Parts are checked for approval against the color match master chip. Finished surface smooth, free of scratches, gouges, drips, bubbles, thickness variations, foreign matter, and other imperfections.

I. Movable parts, including hardware, are to be cleaned and adjusted to operate as designed without binding or deformation of members. Doors and covers centered in opening of frame.

All contact surfaces fit tight and even without forcing or warping components.

J. Shop fabricates so far as practical and pre-assemble items to greatest extent possible to minimize field splicing and assembly. Disassemble units only as necessary for shipping and handling limitations. Clearly mark units for re-assembly and coordinated installation.

PART 3 – EXECUTION

3.01 INSTALLATION

A. Protect products against damage during field handling and installation. Protect adjacent existing and newly placed construction as necessary to prevent damage during installation.

Paint and touch-up any exposed fasteners and connecting hardware to match color and finish of surrounding surface.

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 6

B. Mount signs in proper alignment, level and plumb according to the sign location plan and the dimensions given on elevation and sign location drawings. Where otherwise not dimensioned, signs shall be installed where best suited to provide a consistent appearance throughout the project. When exact position, angle, height or location is in doubt, contact Architect for clarification.

C. At completion of sign installation, clean exposed sign surfaces. Clean and repair any adjoining surfaces that became soiled or damaged as a result of installation of signs.

D. Locate signs as shown on the Sign Location Plan.

E. At completion of installation, turn over any additional stock of signs and sign components listed in the Sign Message Schedule.

3.02 SIGN MESSAGE SCHEDULE

A. The Sign Message Schedule and Sign Location Plans are inter-related documents. These documents represent location, type, and total number of signs required.

B. Contractors shall clarify any perceived irregularities in the Sign Message Schedule.

C. SPEC WRITER NOTE: Insert the Sign Message Schedule in this location in the specification and it should contain, at minimum, the following information.

1. Location reference number of the sign within or on the building as shown on the Sign

Location Drawing.

2. The text message, arrow, or symbol on the sign.

3. The type of sign (part number & style) to go in/on/at this specific location identified by the location reference number.

4. The size of the sign the message is to appear as shown on the Sign Location Drawings.

5. Reference to the mounting or installation requirements as shown in the drawings.

6. Any special notations or remarks providing classifications and general information regarding a specific sign at a particular location.

TECHNICAL SPECIFICATIONS

1) SLIDE MODULAR SIGN SYSTEM

A. RAILS

1. Internal Structural Rails

2. Extruded Aluminum 6063 Alloy, T-5 Temper, Anodized Black

B. INSERTS

1. ABS Inserts

2. .090” extruded ABS plastic core with .003” KORAD acrylic cap bonded during the extrusion/texturing process.

3. Painted ABS Inserts are sprayed with PPG Automotive Acrylic Lacquer. Interior and exterior applications. UV resistant. Fade resistant to 5 years.

4. Window Inserts

5. Extruded 6063-T5 aluminum with integral hooks for connection to Structural Rail. Color is anodized black, anodized satin or painted acrylic lacquer. Inserts hold die-cut paper insert with a clear .020” textured polycarbonate lens.

6. Acrylic Windows

7. .060” non-glare acrylic bonded to .030 ABS and pressure bonded to extruded hook or magnetic tape.

8. Fire Rating

9. UL 94

10. Flame Spread

11. UL94HB

12. Smoke Development

13. NVS Smoke Test/E84 Steinner Tunnel Test: 450 smoke density. Begins smoking upon ignition.

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 7

14. ADA, Direct Print Tactile Inserts

15. UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2

Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

C. END CAPS

1. ABS

2. Injection molded, Toyolac 100 General Purpose ABS plastic

3. Flammability

4. 94HB

5. Extruded Aluminum

6. Extruded aluminum 6063, T-5 Temper

7. Spring Steel Clips

8. .018” spring steel for Standard, and .020” spring steel clips for Thin, black zinc plated.

D. MOUNTS

1. Wall Mounts

2. A-Adhesive Tape for smooth, hard surfaces.

3. D-Screw for rough surfaces and all signs exceeding 100 square inches.

4. K-Perpendicular to wall. Sign is two-sided and connects to a black anodized aluminum bracket at a 90° angle.

E. TRIM

1. Extruded Aluminum

2. Extruded aluminum 6063, T-5 Temper; Finish anodized or painted acrylic lacquer.

F. COPY OPTIONS

1. First Surface Copy Options

a. Direct Print

b. Laser Print

2. ADA, Tactile Copy Option

a. ADA, Direct Print Tactile

5.02 PLAQUES

A. PLAQUE MATERIAL

1. ABS Plaque

2. .090” extruded ABS plastic core with .003” KORAD acrylic cap bonded during the extrusion/texturing process.

3. Painted ABS Plaques are sprayed with PPG Automotive Acrylic Lacquer. Interior and exterior applications. UV resistant. Fade resistant to 5 years.

4. Acrylic Windows

5. .060” non-glare acrylic bonded with .030” ABS with adhesive to .093 ABS plastic.

a. Fire Rating

1) UL 94

b. Flame Spread

1) UL94HB

c. Smoke Development

1) NVS Smoke Test/E84 Steinner Tunnel Test: 450 smoke density. Begins smoking upon ignition.

6. ADA, Direct Print Tactile Plaque

7. UV/LED-cured, 1/32” thick, direct-print raised characters and fully domed, clear Grade 2

Braille dots, printed on ABS, anodized aluminum, high-pressure laminates, acrylic, or direct-print background graphics Inserts. Background color for painted materials is painted with acrylic lacquer in the specified Insert color. Copy color is UV/LED-cured inks digitally applied directly to the substrate surface.

February 10, 2026 QE Project # 42137280

101400 Panel Signage - 8

B. MOUNTS

1. Wall Mounts

2. A-Adhesive Tape for smooth, hard surfaces.

3. D-Screw for rough surfaces and all signs exceeding 100 square inches.

C. COPY OPTIONS

1. First Surface Copy

a. Direct Print

b. 3M High Performance Cast PVC Vinyl

2. ADA, Tactile Copy

a. ADA, Direct Print Tactile

CLEANING GUIDELINES FOR 2/90 SIGNAGE PRODUCTS

FOR ROUTINE MAINTENANCE, USE A MILD CLEANSER (SUCH AS HAND SOAP OR DISH

DETERGENT) AND LUKEWARM WATER. WIPE WITH A SPONGE OR SOFT CLOTH. AFTER

WASHING AND RINSING, BLOT DRY WITH A SOFT CLOTH OR CHAMOIS.

BEFORE USING ANY OTHER CLEANING SOLUTION, ALWAYS TEST ON AN INCONSPICUOUS

AREA OF THE SIGN. APPLY THE SOLUTION TO A CLOTH RATHER THAN SPRAYING DIRECTLY

ON THE SIGN. SANITIZE ALL SURFACES WITH THE DAMP CLOTH AND BLOT DRY WITH A DRY

CLOTH OR ALLOW TO AIR DRY.

SOLVENT BASED CLEANERS CAN DEGRADE FINISHES OVER TIME. USE THE MINIMUM RATIO

OF SOLVENT TO WATER NECESSARY FOR EFFECTIVE SANITATION. ADDITIONAL CAUTION

SHOULD BE EXERCISED ESPECIALLY ON PAINTED SURFACES.

FOR SPECIAL MAINTENANCE, CALL THE CUSTOMER SERVICE DEPARTMENT. DO NOT USE

ALCOHOL OR OTHER CLEANING SOLUTIONS.

END OF SECTION

DEMOLITION LEGEND

ITEM / CONSTRUCTION

TO BE REMOVED,

SALVAGED OR

REINSTALLED

EXISTING DOOR

TO REMAIN

EXISTING CONSTRUCTION

TO REMAIN

DOOR TO BE REMOVED,

SALVAGED OR

REINSTALLED

D27.1

D27.2

D06.1

D06.1

D06.2

D06.2

TYP OF 10

THIS FLOOR

D09.1

D09.2

D09.2

D27.5

D08.3

D08.3 D06.4

D06.4

D10.2 D10.1

D10.4 D10.3 D27.6

D10.5

D06.3

D06.6

D06.6

D27.7

LINE OF WALL

ABOVE - TYP

D10.6 1

SHEET NOTES

1. COORDINATE DEMOLITION WITH NEW

WORK.

2. PROTECT ALL EXISTING FURNITURE

AND EQUIPMENT FOR REINSTALLATION

OR RETURN TO OWNER - REFER TO

DEMO FURNITURE PLANS.

3. UNO WHEREEVER NEW FLOOR

FINISHES ARE SCHEDULED, REMOVE

EXISTING FLOOR FINISH, REMOVE

EXISTING BASE & PREP SUBSTRATE

FOR NEW FLOOR FINISH. REFER TO

FINISH PLANS FOR AREAS TO RECEIVE

NEW FINISHES.

NOT IN

SCOPE

M

AI

N

EN

TR

Y

KEYPLAN

PROJECT

NORTH

0'

PA

TH

F

IL

EN

AM

E:

PL

O

TT

IN

G D

AT

E

TI

M E:

A

DRAWN BY:PROJECT MANAGER:

QUINNEVANS.COM

2101 L STREET, NW

SUITE 950

WASHINGTON, DC 20037

v 202.298.6700

M

B

C

D

E

F

G

H

J

K

L

122 3 4 5 6 7 8 9 10 11

1 122 3 4 5 6 7 8 9 10 11

2' 8' 16'4'

Au to de sk

D oc s:

//S t M ar ys C ol le ge o f M ar yl an d Li br ar y R ev /S

M C

M L ib ra ry R en ov at io n_

.rv t 2/

9/

:3 0:

P

M

AD101

DEMO PLAN - FIRST

FLOOR

AuthorChecker

QEA No.42137280

ST. MARY'S CITY, MD 20686

APRIL 30, 2025

CONSTRUCTION DOCUMENTS

LANDERS LIBRARY

RENOVATION

ST. MARY'S COLLEGE OF

MARYLAND

1/8" = 1'-0"AD101

A1 PARTIAL FIRST FLOOR DEMO PLAN - WEST

KEYNOTES

D06.1 REMOVE COUNTER AND WALL

SUPPORT BRACKETS

D06.2 REMOVE WOOD CHAIR RAIL AND

BASE AT FREESTANDING

COLUMNS - TYP

D06.3 REMOVE EXISTING MILLWORK

D06.4 REMOVE CASEWORK

D06.6 REMOVE CHAIR RAIL AND WOOD

BASE AT ELEVATOR LOBBY - TYP

D08.3 REMOVE ACCORDION DOOR

D09.1 WALL REMOVAL FOR

INSTALLATION OF NEW INTERIOR

WINDOW - COORDINATE WITH

NEW WORK

D09.2 REMOVE THINSET QUARRY TILE

IN AREA INDICATED

D10.1 REMOVE SIGNAGE

D10.2 REMOVE BULLETIN BOARD

D10.3 REMOVE HAND SANITIZER

STATION

D10.4 REMOVE PHI BETA KAPPA SIGN

AND RETURN TO OWNER -

OWNER TO CONFIRM DEMO IS

ACCEPTABLE

D10.5 REMOVE DIRECTORY

D10.6 REMOVE AND PROTECT EXISTING

GLASS MARKERBOARDS (2). FOR

REINSTALLATION. REFER TO

CONSTRUCTION ELEVATIONS

FOR NEW LOCATIONS.

D27.1 REMOVE EXISTING WALL WHILE

PROTECTING EXISTING DATA

CABLE RUN VERTICALLY

THROUGH IT

D27.2 REMOVE POTS LINES RUN IN

WALL

D27.5 PRIOR TO ANY DEMOLITION IN

THIS AREA, MEET WITH SMCM OIT

DEPARTMENT AND THEIR SUB

CONTRACTOR(S) TO CONFIRM

WHAT INFRASTRUCTURE TO

REMOVE AND THE TIMING OF ANY

INFRASTRUCTURE REMOVAL

D27.6 RELOCATE EXISTING HAND

TELEPHONE - REFER TO

CONSTRUCTION PLANS FOR NEW

LOCATION

D27.7 REMOVE DIGITAL DISPLAY

SCREEN, MOUNT, BACKBOX AND

ASSOCIATED WIRING - RETURN

TO OWNER

No. Date Description

1 10 FEB 2026 ADD 1

H

FIRST FLOOR

17' - 8"

WORLD MAP GRAPHIC

ON 25MM PET FELT

09.01

27.1

3B

3C

9'

0" 6"

2' - 5 1/16" 12' - 0" 6"

PT 3A

CREDENZA

09.02D

4' - 0" 4' - 0" 4' - 0"

FIRST FLOOR

17' - 8"

27.1

09.01

4'

0"

CREDENZA

EQEQ

G

FIRST FLOOR

17' - 8"

27.1

4'

0"

5' - 5"

FIRST FLOOR

17' - 8"

27.1

EQEQ

4'

0"

HVAC WALL

FIN UNIT

B3

A513

FIRST FLOOR

17' - 8"

27.1

EQEQ

4'

0"

H

FIRST FLOOR

17' - 8"

09.01

4A

SF02

09.01

SHEET NOTES

1.

2.

ALL WALLS ARE TO BE PAINTED (PT1)

UNO

REFER TO STOREFRONT TYPES SHEET

FOR MORE INFORMATION

G

FIRST FLOOR

17' - 8"

2A

EQ EQ

10.03D

TYPICAL WALL PAINT UNO -

BOD BM OC-17 WHITE DOVE

PAINT FINISH LEGEND

PT 1A

ACCENT WALL PAINT - YELLOW 1

(RICH) - BOD BM 378 GIBSON

GOLD

PT 2A

PT 3A

ACCENT WALL PAINT - BLUE 1

(DEEP) - BM CSP-690 HIDDEN

SAPPHIRE

PT 5

PAINT AT HOLLOW METAL FRAMES

AND PAINTED FLUSH DOORS - TO

MATCH KAWNEER PERMAFLOUR

ZINC GRAY (SHADE BETWEEN BM

HC-166 & HC 167)

PT 6 TYPICAL CEILING PAINT

BM PM-1

ACCENT WALL PAINT - YELLOW 2

(POP) - BOD BM 377 MUSTARD

FIELD

PT 2B

PT 3B ACCENT WALL PAINT - BLUE 2

(POP) - BM 749 BAINBRIDGE BLUE

PT 4

ACCENT WALL PAINT - GRAY - BM

1483 COB COB STONEWALL

CREAM WHITE WALL PAINT TO

MATCH EXISTING WALL PAINTPT 1B

PA

TH

F

IL

EN

AM

E:

PL

O

TT

IN

G D

AT

E

TI

M E:

A

DRAWN BY:PROJECT MANAGER:

QUINNEVANS.COM

2101 L STREET, NW

SUITE 950

WASHINGTON, DC 20037

v 202.298.6700

M

B

C

D

E

F

G

H

J

K

L

122 3 4 5 6 7 8 9 10 11

1 122 3 4 5 6 7 8 9 10 11

Au to de sk

D oc s:

//S t M ar ys C ol le ge o f M ar yl an d Li br ar y R ev /S

M C

M L ib ra ry R en ov at io n_

.rv t 2/

/2

9:

:4

AM

A432

INTERIOR

ELEVATIONS

AuthorChecker

QEA No.42137280

ST. MARY'S CITY, MD 20686

APRIL 30, 2025

CONSTRUCTION DOCUMENTS

LANDERS LIBRARY

RENOVATION

ST. MARY'S COLLEGE OF

MARYLAND

1/4" = 1'-0"A432

C3 INT ELEV - OIE LOBBY NORTH

1/4" = 1'-0"A432

C2 INT ELEV - OIE LOBBY WEST

1/4" = 1'-0"A432

B1 INT ELEV - OIE 122B NORTH

1/4" = 1'-0"A432

B2 INT ELEV - OIE 123B WEST

1/4" = 1'-0"A432

A2 INT ELEV - OIT DIGITAL MEDIA LAB SOUTH

1/4" = 1'-0"A432

B3 INT ELEV - OIE 122A EAST

KEYNOTES

09.01 ACOUSTIC WD SLAT WALL

CLADDING - REFER TO A1/A801

09.02D WORLD MAP GRAPHIC - CUSTOM

PRINTED WORLD MAP IMAGE ON

25MM PET FELT PANEL BOD:

ACOUFELT SOLID 25MM PANEL -

FURNISH AND INSTALL BY

OWNER'S SIGNAGE VENDOR.

10.03D RELOCATED EXISTING GLASS

MARKERBOARD - PROVIDE

BLOCKING IN WALL FOR

INSTALLATION

27.1 DISPLAY SCREEN - COORD

POWER AND DATA RECEPTACLE

LOCATIONS WITH WALL BRACKET

TO BE CONCEALED BEHIND

SCREEN - REFER TO TA

DRAWINGS AND SPECS

1/4" = 1'-0"A432

B4 INT ELEV - OIE 122A SOUTH

No. Date Description

FIRST FLOOR

17' - 8"

2'

EQEQ

27.1

1/2"3' - 0"3' - 3"3' - 3"3' - 3"3' - 3"3' - 3"3' - 0"1/2"

A4

A801

PT 2B

PL01

SS01

FIRST FLOOR

17' - 8"

I.5

EQ EQ

4'

0"

27.1

27.6

I

FIRST FLOOR

17' - 8"

OP

EN

HALF WALL FOR RUNNING

EXISTING AV/IT CABLE

EXISTING CCPD DONOR WALL

SIGNAGE - OWNER FURNISHED

OWNER INSTALLED

RECEPTION DESK FURNITURE

INSTALLED AROUND HALF

WALL BY OWNER

O

PE

N

2'

0"

FIRST FLOOR

17' - 8"

SF06

4A

B

THIRD FLOOR

45' - 0"

27.1

4'

0"

EQ EQ

HVAC WALL

FIN UNIT

3 2

THIRD FLOOR

45' - 0"

HVAC WALL

FIN UNIT

7' - 6"7' - 6"

27.1 27.1

10.03C

4'

0"

10.03C

WDW

OPPOSITE

ALIGN - TYP

SHEET NOTES

1.

2.

ALL WALLS ARE TO BE PAINTED (PT1)

UNO

REFER TO STOREFRONT TYPES SHEET

FOR MORE INFORMATION

SECOND FLOOR

31' - 0"

4'

0"

27.1

EQEQ HVAC WALL

FIN UNIT

SECOND FLOOR

31' - 0"

27.1

EQ EQ

4'

0"

J

FIRST FLOOR

17' - 8"

I.5

EQ EQ

5'

0"

HVAC WALL

FIN UNIT

10.03D

I H

FIRST FLOOR

17' - 8"

EQ EQ

4'

0"

A513 C4

27.1

OPE

N

HVAC WALL

FIN UNIT

TYPICAL WALL PAINT UNO -

BOD BM OC-17 WHITE DOVE

PAINT FINISH LEGEND

PT 1A

ACCENT WALL PAINT - YELLOW 1

(RICH) - BOD BM 378 GIBSON

GOLD

PT 2A

PT 3A

ACCENT WALL PAINT - BLUE 1

(DEEP) - BM CSP-690 HIDDEN

SAPPHIRE

PT 5

PAINT AT HOLLOW METAL FRAMES

AND PAINTED FLUSH DOORS - TO

MATCH KAWNEER PERMAFLOUR

ZINC GRAY (SHADE BETWEEN BM

HC-166 & HC 167)

PT 6 TYPICAL CEILING PAINT

BM PM-1

ACCENT WALL PAINT - YELLOW 2

(POP) - BOD BM 377 MUSTARD

FIELD

PT 2B

PT 3B ACCENT WALL PAINT - BLUE 2

(POP) - BM 749 BAINBRIDGE BLUE

PT 4

ACCENT WALL PAINT - GRAY - BM

1483 COB COB STONEWALL

CREAM WHITE WALL PAINT TO

MATCH EXISTING WALL PAINTPT 1B

PORCELIN WALL TILE - BOD

MOSA COLORS 18900-1515

CASEWORK FINISH LEGEND

CT 1

PL01

PLASTIC LAMINATE - BOD

FORMICA - HARD ROCK MAPLE

86992

WV 1 WOOD VENEER - MAPLE

GLAZING GL 1

PL02

SS01 SOLID SURFACE - BOD

CORIAN ANTARTICA

PLASTIC LAMINATE - BOD

FORMICA - GRAYSTONE 464

WD 1 SOLID WOOD - MAPLE

GYP BD - PAINTED PT-1AGYP 1

PA

TH

F

IL

EN

AM

E:

PL

O

TT

IN

G D

AT

E

TI

M E:

A

DRAWN BY:PROJECT MANAGER:

QUINNEVANS.COM

2101 L STREET, NW

SUITE 950

WASHINGTON, DC 20037

v 202.298.6700

M

B

C

D

E

F

G

H

J

K

L

122 3 4 5 6 7 8 9 10 11

1 122 3 4 5 6 7 8 9 10 11

Au to de sk

D oc s:

//S t M ar ys C ol le ge o f M ar yl an d Li br ar y R ev /S

M C

M L ib ra ry R en ov at io n_

.rv t 2/

/2

9:

:2

AM

A433

INTERIOR

ELEVATIONS

AuthorChecker

QEA No.42137280

ST. MARY'S CITY, MD 20686

APRIL 30, 2025

CONSTRUCTION DOCUMENTS

LANDERS LIBRARY

RENOVATION

ST. MARY'S COLLEGE OF

MARYLAND

1/4" = 1'-0"A433

A1 INT ELEV - CLASSROOM 312 SOUTH

1/4" = 1'-0"A433

A2 INT ELEV - CLASSROOM 312 WEST

1/4" = 1'-0"A433

B1 INT ELEV - CCPD CAREER STUDIO WEST

1/4" = 1'-0"A433

C3 INT ELEV - CONFERENCE 112 SOUTH

1/4" = 1'-0"A433

B2 INT ELEV - CCPD LOBBY SOUTH

1/4" = 1'-0"A433

B3 INT ELEV - CCPD LOBBY WEST

KEYNOTES

10.03C GLASS MARKERBOARD - 4 x 8

10.03D RELOCATED EXISTING GLASS

MARKERBOARD - PROVIDE

BLOCKING IN WALL FOR

INSTALLATION

27.1 DISPLAY SCREEN - COORD

POWER AND DATA RECEPTACLE

LOCATIONS WITH WALL BRACKET

TO BE CONCEALED BEHIND

SCREEN - REFER TO TA

DRAWINGS AND SPECS

27.6 SLIM AV CABINET - BOD: 2 BAY,

32" TALL C3 SERIES BY MIDDLE

ATLANTIC - REFER TO AV -

FURNISH AND INSTALL BY

CONTRACTOR

1/4" = 1'-0"A433

D3 INT ELEV - TYPICAL STUDY ROOM

1/4" = 1'-0"A433

D2 INT ELEV - STUDY RM 206

1/4" = 1'-0"A433

C2 INT ELEV - CONFERENCE 112 NORTH

1/4" = 1'-0"A433

C1 INT ELEV - CCPD CAREER STUDIO NORTH

No. Date Description

A703 A2

C-8

T-12

C-8C-8

C-8

T-7

T-7 C-5 C-5

C-5

C-5 C-5

C-5

RELOCATED FURNITURE

LEGEND

FURNITURE TO REMAIN

IN EXISTING LOCATION

NEW FURNITURE - IS

TAGGED

CASEWORK - NOT IN

FURNITURE CONTRACT

2'

9"

4' - 8 1/4"

2'

9"

6' - 8 1/4"

12.02A

12.02B

12.02A

26.07

26.07

26.07

26.07

26.07

T-7

C-8C-8

T-12

C-8 C-8

T-7

C-5 C-5

C-5

C-5

C-5C-5

LOUVERED CEILING WITH

CENTER ORIENTED FAN &

LIGHT PLANK - (1 OF 3)

SHEET NOTES

1. FURNITURE IS SHOWN FOR REFERENCE

ONLY AND WILL BE PROCURED UNDER A

SEPRATE CONTRACT

2. PODS ARE SHOWN FOR REFERENCE

ONLY AND WILL BE PROCURED UNDER A

SEPRATE CONTRACT

PROJECT

NORTH

0'

PA

TH

F

IL

EN

AM

E:

PL

O

TT

IN

G D

AT

E

TI

M E:

A

DRAWN BY:PROJECT MANAGER:

QUINNEVANS.COM

2101 L STREET, NW

SUITE 950

WASHINGTON, DC 20037

v 202.298.6700

M

B

C

D

E

F

G

H

J

K

L

122 3 4 5 6 7 8 9 10 11

1 122 3 4 5 6 7 8 9 10 11

2' 8' 16'4'

Au to de sk

D oc s:

//S t M ar ys C ol le ge o f M ar yl an d Li br ar y R ev /S

M C

M L ib ra ry R en ov at io n_

.rv t 2/

9/

:3 0:

P

M

A703

FURNITURE &

EQUIPMENT PLAN - L2

WEST

AuthorChecker

QEA No.42137280

ST. MARY'S CITY, MD 20686

APRIL 30, 2025

CONSTRUCTION DOCUMENTS

LANDERS LIBRARY

RENOVATION

ST. MARY'S COLLEGE OF

MARYLAND

1/8" = 1'-0"A703

A1 FURNITURE PLAN - L2 WEST

1/4" = 1'-0"A703

A2 ENLARGED PLAN @ PODS

1/4" = 1'-0"A703

A3 RCP @ PODS

No. Date Description

1 10 FEB 2026 ADD 1

KEYNOTES

12.02A 8 X 8 NOM POD

12.02B 8 X 10 NOM POD - CEILING SLATS

ONLY

26.07 OUTLET PROVIDED WITH POD