36E77619R0085-018.pdf

VA MEDICAL CENTER

DALLAS, TEXAS

BUILDING 5

A.H.E.R.A. ASBESTOS INSPECTION

MANAGEMENT PLAN

3-YEAR REASSESSMENT & UPDATE - 2014

PREPARED FOR:

VA NORTH TEXAS HEALTH CARE SYSTEM

ENGINEERING SERVICES

4500 S. LANCASTER ROAD

DALLAS, TX 75216

MICRO AIR PROJECT #B-1403

PREPARED BY:

MICRO AIR OF TEXAS, INC.

P.O. Box 1225 Dickinson, TX 77539

(281) 280-9965

DALLAS, TEXAS

AHERA

ASBESTOS INSPECTION

PREPARED FOR:

VA NORTH TEXAS HEALTH CARE SYSTEM

ENGINEERING SERVICES

4500 S. LANCASTER ROAD

DALLAS, TX 75216

PREPARED BY:

MICRO AIR OF TEXAS, INC.

P.O. Box 1225 Dickinson, TX 77539

(281) 280-9965

Original Inspection Date: January 13, 2010

Individual Asbestos Consultant: ________________________

DSHS License # 10-5436

TABLE OF CONTENTS

Page #

General Inventory Management Plan Format

Section I - AHERA Asbestos Inspection General Information

Introduction, Required Information, & Facility Description 1 - 2

Section II - Asbestos Methodology & Lab Analytical Report

Methodology 3 Classification 3 Limitations 4 Homogeneous Sampling Area Summary Table 5 - 7 Laboratory Report Sample Location Drawing(s) Homogeneous Area Location Drawing(s)

Section III - ACM Material Assessment & Quantification

General Information 1 - 2 Surfacing Materials 3 Thermal System Insulation Materials 3 - 4 Miscellaneous Materials 5 - 15 Photos of Asbestos-containing Homogeneous Areas

Section IV - Asbestos Material Response Action Recommendations

Introduction 1 Response Action Prioritization 2 Response Action Recommendations 3 - 4

Section V - Operations & Maintenance Program

Purpose 1 Scope 1 Facility ACM 2 Operations & Maintenance Recommendations 3 - 4 O&M Activities 5

Section VI - Facility Owner / Designated Person(s)

Licenses and Training Certificates

Section VII - Six Month Surveillance Documentation

Section VIII - Three Year Reinspection Updates

Section IX - Response Actions

BUILDING INSPECTION FOR FRIABLE AND NON-FRIABLE ACM

GENERAL INVENTORY

FACILITY ID: Building 5

ORIGINAL INSPECTION COMPLETION DATE: January 13, 2010 3-YEAR RE-ASSESSMENT INSPECTION DATE: May 28, 2014

FACILITY ADDRESS: Building 5

VAMC

4500 S. Lancaster Road Dallas, TX 75216

TOTAL SQUARE FOOTAGE: APPROXIMATELY 3,419 SF

YEAR CONSTRUCTED: 1940

USE OF FACILITY: EMS OFFICES & NURSE CALL CENTER

DESIGNATED PERSON: Thomas Rattler or Ken Taylor

ENGINEERING PHONE: 214-857-1069 - Contact Charles Ballard

INSPECTION COMPANY: MICRO AIR OF TEXAS, INC.

P.O. BOX 1225

DICKINSON, TX 77539

PHONE: (281) 280-9965

NAME OF ACCREDITED PERSONS

PERFORMING INSPECTION: JENNIFER MCMILLIN (DSHS LICENSE # 60-1893)

ELIZABETH BARGAR (DSHS LICENSE # 60-2614)

ACCREDITATION AGENCY: TEXAS DEPT. OF STATE HEALTH SERVICES

ACCREDITATION #: N/A

THIS BUILDING CONTAINS:

1. FRIABLE ACBM X

2. NON-FRIABLE ACBM X

3. FRIABLE MATERIAL

(ASSUMED TO BE ACBM)

4. NON-FRIABLE MATERIAL

(ASSUMED TO BE ACBM)

5. NONE OF THE ABOVE

___________________________ _______2/12/10_____________

ACCREDITED INSPECTOR DATE

DSHS LICENSE # 60-1893

BUILDING 5

DALLAS, TX

A.H.E.R.A. ASBESTOS INSPECTION &

MANAGEMENT PLAN

PREPARED FOR:

VA NORTH TEXAS HEALTH CARE SYSTEM

ENGINEERING SERVICES

4500 S. LANCASTER ROAD

DALLAS, TX 75216

MICRO AIR PROJECT #A-1001

PREPARED BY:

MICRO AIR OF TEXAS, INC.

P.O. Box 1225

MICRO AIR OF TEXAS, INC. BUILDING 5 - VA Medical Center; Dallas, TX

AHERA ASBESTOS INSPECTION & MANAGEMENT PLAN

P.O. Box 1225

MANAGEMENT PLAN FORMAT

SECTION I: This section contains general information regarding the AHERA survey and management plan, required information, and a facility description.

SECTION II: This section contains general information, sampling information, and Homogeneous Sample Area Summary. The laboratory analytical report for the bulk samples collected during the 2010 inspection has been included. Additionally, information on the survey report and classification of homogeneous areas is located in this section. Drawings depicting the locations of all bulk building material samples collected and asbestos-containing homogeneous area locations can be found in this sub-section.

SECTION III: This section contains material assessments and quantification which are used to develop the appropriate response actions for the management plan. Photographs of each asbestos-containing material identified has been included in this section.

SECTION IV: This section contains the recommended response actions for each type of ACM in the facility including recommendations for immediate abatement, if necessary. Immediate response action recommendations are prioritized.

SECTION V: This section contains an updated Operations and Maintenance Program for the facility.

This program includes recommendations for ongoing maintenance functions.

SECTION VI: This section has been reserved for informational purposes. This section includes the Facility Owner / Designated Person information, as well as the Re-inspection / Periodic Surveillance Schedule. All applicable licenses, certifications, and accreditations of the Inspector, Management Planner, and Laboratory performing services on this Management Plan are also included in this section.

SECTION VII: This section has been reserved for reports for the six month inspections, assessments, and any ambient air monitoring.

SECTION VIII: This section has been reserved for documentation obtained from three year re-inspections. Updates to the Management Plan are to be included in this section.

SECTION IX: This section has been reserved for the owner to reference abatement response action reports and building maintenance action (O&M) reports. All documentation from asbestos abatement activities should also be included in this section.

SECTION I

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 1

AHERA ASBESTOS INSPECTION

SECTION I - GENERAL INFORMATION

Introduction

Micro Air of Texas, Inc. (Micro Air) was contracted by the Veterans Administration North Texas Health Care System (VANTHCS) located in Dallas, Texas to perform an asbestos inspection and generate a management plan in accordance with guidelines established in 40 CFR 763, the Asbestos Hazard Emergency Response Act of 1987 (AHERA), for the Veterans Administration Medical Center (VAMC) located in Dallas, Texas. This facility consists of numerous buildings constructed between 1940 and 2009. This particular report pertains to Building 5, which formerly housed Home Based Care and is currently EMS Offices and Nurse Call Center (as of 2014).

Micro Air performed a comprehensive asbestos survey of Building 5 on January 13, 2010.

After the comprehensive asbestos survey results were compiled, a Management Planner accredited by an EPA-approved training provider and licensed as an Individual Asbestos Consultant in the state of Texas, reviewed the analytical results of the inspection and current physical condition assessments. The management planner then determined the potential hazard posed by the ACM and evaluated and selected control / response options based on all compiled information. This information was then composed and written into a final report.

The federal National Emission Standard for Asbestos (NESHAP) and the Texas Asbestos Health Protection Act (TAHPA) both require that prior to any demolition or renovation activity in a building, a thorough inspection of the affected facility or part of the facility where the demolition or renovation operation will occur, must be performed for the presence of asbestos, including Category I and Category II non-friable asbestos-containing material (ACM).

Additionally, TAHPA requires that a minimum of three samples be collected from each homogeneous sampling area (material type) identified in the building. The work area and immediately surrounding areas which could foreseeably be disturbed by the actions necessary to perform the project must be inspected and sampled as applicable prior to renovations or demolition. While the VANTHCS is not subject to the TAHPA regulation, due to its exclusion as a federal facility, Micro Air collected bulk samples in accordance with TAHPA and AHERA protocol at the request of the VANTHCS engineering personnel.

A 3-Year Asbestos Reassessment and Inspection was conducted in May, 2014. See Section 8 for additional information.

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 2

Required Information

In accordance with AHERA protocol, the VAMC located in Dallas, Texas is required to name a person who shall be responsible for implementation of the management plan (Designated Person - see Section V). Per the Occupational Safety and Health Administration (OSHA) 1926.1101, construction industry standard, maintenance personnel should be made aware of the types and locations of all facility ACM. These employees are required to have adequate asbestos awareness training (minimum 2 hours), and all maintenance personnel who may come in contact with or disturb ACM are required to receive a minimum of 16 hours of asbestos training in asbestos hazards and recognition of ACM. If the owner wishes to perform ACM activities with its own personnel, the owner is responsible for obtaining the required EPA training in accordance with the Model Accreditation Plan (MAP), which is located in Appendix C, Subpart E of 40 CFR, 763 (AHERA). Additionally, all OSHA requirements must be met, as well (i.e., asbestos physical, etc.). Otherwise, it is recommended that all ACM activities be performed by a Texas licensed Asbestos Contractor, and project oversight be conducted by a Texas licensed Asbestos Consultant Agency.

In accordance with the VA directive to comply with AHERA, the entire facility must be re-inspected and a reassessment of ACM conducted by an accredited inspector at least once every three years, and the management plan should be updated by a licensed Asbestos Inspector / Management Planner or Individual Asbestos Consultant. Additionally, visual inspections of the ACM must also be made by the Designated Person for the facility at least once every six months to determine whether any areas of the material have changed in condition, or if there are any other factors which may necessitate abatement actions.

FACILITY DESCRIPTION

Building 5 is approximately 3,419 square feet in size, and it formerly served as Home Based Care for the Dallas VA; the building is currently vacant. The construction date of this building is believed to be 1940; the date of an addition on the west side of the first floor consisting of two rooms (101 A and 101 B) was not provided (it appears that an exterior porch area was enclosed at some point). The building consists of a concrete foundation with a basement, two aboveground floors and an attic. The walls on the first and second floors of the building are primarily plaster and sheetrock. The walls on the basement level are primarily sheetrock. The ceilings on the first and second floors were originally plaster; numerous drop ceilings with lay-in ceiling tile have been installed below the original plaster ceilings. The original ceiling in the two rooms on the west side of the building (101A and 101B) was beadboard wood. It appears that most of the original plaster ceilings in the basement level were removed prior to installation of drop ceilings with lay-in ceiling tile. Most of the floors in the building are carpeted with concrete or wood beneath; several types of vinyl floor tile were also observed.

Two layers of floor tile are present in some areas of the basement level; residual black floor tile mastic was also noted in one section of the basement. There was limited access to areas located above the plaster ceilings; therefore, it is assumed that pipes exist above the solid ceilings and in wall chases. The exterior of the building is brick with a shingled roof.

SECTION II

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 3

SECTION II- ASBESTOS LABORATORY ANALYTICAL REPORT

METHODOLOGY

Micro Air of Texas, Inc. performed a comprehensive asbestos survey of Building 5 on January 13, 2010 in accordance with AHERA and TAHPA sampling protocol and assessment factors.

The inspection was performed by Jennifer McMillin, an accredited asbestos inspector who is licensed as a Building Inspector by the state of Texas (license #60-1893) and Elizabeth Bargar, an accredited and state licensed asbestos inspector (license #60-2614). Micro Air of Texas, Inc. is licensed as an Asbestos Consulting Agency (#10-0110). All samples collected during this inspection were analyzed by J Resources, Inc., whose laboratory is accredited by3 the National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP) program (accreditation #200525-0) and licensed by the state of Texas (license #30-0273). Laboratory analysis of collected samples was performed in accordance with EPA and NVLAP prescribed methodologies for Polarized Light Microscopy of bulk material samples for the presence of asbestos. The results of laboratory analysis of collected bulk material samples are included in this section for reference.

A total of 77 bulk material samples were collected during this comprehensive survey, and 73 of the collected samples were analyzed by PLM. Federal regulations require that each identifiable layer of an individual bulk building material sample be analyzed separately for asbestos content. In addition, federal regulations state that if any one sample from a homogeneous area is found to be asbestos-containing, then the entire homogeneous area is considered asbestos-containing, regardless of the results from the remaining samples from that homogeneous area.

CLASSIFICATION

All materials which were sampled as being suspect for containing asbestos or were assumed to be asbestos-containing were grouped by sample type into Homogeneous Sampling Areas for purposes of assessment and quantification. Homogeneous materials are those which have similar appearance, texture, and function. If the inspector believes these materials to be the same, even if they are located in separate areas of a building, they may be grouped into the same sampling set. For purposes of this inspection report, the Homogeneous Area is designated as : HA. Each Homogeneous Area is given a number to distinguish it from other Homogeneous Areas (Example: HA-01A).

A CAD drawing(s) demonstrating the location of each collected bulk building material sample has been included in this section, as well as a CAD drawing(s) depicting the location of asbestos-containing homogeneous areas.

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 4

LIMITATIONS

Micro Air’s scope of services was limited primarily to accessible interior building materials.

While Micro Air made every effort to perform a thorough survey, the possibility exists that materials containing asbestos were not identified, inaccessible, or different from those identified at other locations. The findings and opinions presented are indicative of conditions on the date of our site inspection and should not be relied upon to represent conditions at substantially later dates, due to possible changes in the condition of building materials, renovations, and repairs. Additionally, most of the buildings located at this VA facility have steam pipes running underground to supply heat to each building. This material was inaccessible at the time of this inspection. All pipes located in wall chases, underground, in the crawlspace of a building, etc., is assumed to be ACM until tested and proven otherwise.

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 5

VAMC - DALLAS, TX

BUILDING 5

HOMOGENEOUS SAMPLE AREA SUMMARY

THE FOLLOWING TABLE DENOTES THE HOMOGENEOUS AREAS

IDENTIFIED IN BUILDING 5. THE TABLE INDICATES THE NUMBER OF

BULK BUILDING MATERIAL SAMPLES COLLECTED FOR EACH

HOMOGENEOUS AREA AND WHETHER THE HOMOGENEOUS AREA WAS

ASBESTOS-CONTAINING. ADDITIONALLY, ESTIMATED QUANTITIES OF

THE VARIOUS BUILDING MATERIALS SAMPLED HAVE ALSO BEEN

INCLUDED IN THE TABLE.

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 6

VAMC; DALLAS, TX

BUILDING 5

HOMOGENEOUS SAMPLE AREA SUMMARY

Homogeneo us Area #

Sample Type Asbestos-containing

# of Samples Collected

Est.

Quantity

HA-01 Steam Pipe Insulation Yes 1 500 LF

HA-02 Sprinkler Pipe Insulation and White Mastic

No 3 272 LF

HA-03 HVAC Insulation with Plastic Wrap and Yellow Mastic

No 4 140 LF

HA-04 12" x 12" Vinyl Floor Tile, Terrazzo Pattern, Brown and

Beige & Yellow Mastic (Type I)

No 3 180 SF

HA-05 12" x 12" Vinyl Floor Tile, Peach with Specks & Yellow

Mastic (Type II)

No 3 16 SF

HA-06 12" x 12" Vinyl Floor Tile, Red with Specks & Yellow Mastic

(Type III)

No 3 15 SF

HA-07 12" x 12" Vinyl Floor Tile, Pink with Specks & Yellow Mastic

(Type IV)

No 3 30 SF

HA-08 12" x 12" Vinyl Floor Tile, White with Multi-Colored

Specks & Yellow Mastic (Type V)

No 3 300 SF

HA-09 12" x 12" Vinyl Floor Tile, Tan with Specks & Yellow Mastic

(Type VI)

No 3 496 SF

HA-10 Residual Black Floor Mastic On Concrete Beneath Carpet

Yes 3 72 SF (Totally abated 2010)

HA-11 Residual Brown Floor Mastic on Concrete

No 1 36 SF

HA-12 2' x 2' Ceiling Tile, Glacier Style (Type I)

No 3 2,178 SF

HA-13 2' x 2' Ceiling Tile, Flat Pin Hole (Type II)

No 3 176 SF

Homogeneo us Area #

Sample Type Asbestos-containing

# of Samples Collected

Est.

Quantity

M ICRO AIR OF TEXAS, INC. VAMC; Dallas, Texas - Building 5 7

HA-14 1' x 1' Ceiling Tile - Residual No 3 10 SF

HA-15 Ceiling Tile Mastic, Residual, Brown

Yes 3 2 SF (Totally abated 2010)

HA-16 6" Cove Base, Peach & Tan Mastic

No 3 202 SF

HA-17 3" Cove Base, Gray & Yellow Mastic

No 3 85 SF

HA-18 6" Cove Base, Maroon & Tan Mastic

No 3 509 SF

HA-19 6" Cove Base, Dark Blue & Tan Mastic

No 3 22 SF

HA-20 6" Cove Base, Gray & Tan Mastic

No 3 24 SF

HA-21 Sheet Rock (Brown and White), Tape & Joint

Compound

No 3 2,620 SF

HA-22 Sheet Rock (Brown) & Joint Compound

No 3 1,636 SF

HA-23 Wall Texture (Joint Compound Material)

No 3 1,636 SF

HA-24 Plaster No 3 5,174 SF

HA-25 Particle Board, Brown No 3 1,036 SF

HA-26 Firestop Sealant, Pink No 1 1 SF

HA-27 Firestop Sealant, Red No 1 1 SF

HA-28 Firestop Sealant, Cream No 1 1 SF

HA-29 Firestop Sealant, Gray No 1 1 SF

HA-30 Water Proofing, Black No 1 500 SF

Date Received: 22-Jan-2010 29-Jan-2010Date Analyzed:

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

Cellulose FiberYesInsulation, White, Homogeneous Chrysotile Amosite

5-01 25% 5%

10%

Other Non-Fibrous Material 60%

Cellulose Fiber Fibrous Glass

NoLAYER 1 Mastic Wrap, Beige/ Silver, Homogeneous

None Detected5-02 30% 10%

Other Non-Fibrous Material 60%

Fibrous GlassNoLAYER 2 Insulation, Yellow, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

Cellulose Fiber Fibrous Glass

NoLAYER 1 Mastic Wrap, Beige/ Silver, Homogeneous

None Detected5-03 30% 10%

Other Non-Fibrous Material 60%

Fibrous GlassNoLAYER 2 Insulation, Yellow, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

Cellulose Fiber Fibrous Glass

NoLAYER 1 Mastic Wrap, White/ Silver, Homogeneous

None Detected5-04 30% 10%

Other Non-Fibrous Material 60%

Fibrous GlassNoLAYER 2 Insulation, Yellow, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 1 of 15

Lab DirectorLee W. Poye

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Plastic, Beige, Homogeneous

None Detected5-05 Other Non-Fibrous Material 100%

Fibrous GlassNoLAYER 2 Insulation, Beige/ Pink, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

NoLAYER 1 Plastic, Beige, Homogeneous

None Detected5-06 Other Non-Fibrous Material 100%

Fibrous GlassNoLAYER 2 Insulation, Beige/ Pink, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

NoLAYER 1 Plastic, Beige, Homogeneous

None Detected5-07 Other Non-Fibrous Material 100%

Fibrous GlassNoLAYER 2 Insulation, Beige/ Pink, Homogeneous

None Detected 98%

Other Non-Fibrous Material 2%

NoPlastic, Beige, Homogeneous None Detected5-08 Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Brown/ Multi-colored, Homogeneous

None Detected5-09 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 2 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Floor Tile, Brown/ Multi-colored, Homogeneous

None Detected5-10 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Brown/ Multi-colored, Homogeneous

None Detected5-11 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Peach, Homogeneous

None Detected5-12 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Peach, Homogeneous

None Detected5-13 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Peach, Homogeneous

None Detected5-14 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 3 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

WollastoniteNoLAYER 1 Floor Tile, Rose, Homogeneous

None Detected5-15 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

WollastoniteNoLAYER 1 Floor Tile, Rose, Homogeneous

None Detected5-16 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

WollastoniteNoLAYER 1 Floor Tile, Rose, Homogeneous

None Detected5-17 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

WollastoniteNoLAYER 1 Floor Tile, Beige/ Tan, Homogeneous

None Detected5-18 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 4 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

WollastoniteNoLAYER 1 Floor Tile, Beige/ Tan, Homogeneous

None Detected5-19 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

WollastoniteNoLAYER 1 Floor Tile, Beige/ Tan, Homogeneous

None Detected5-20 <1%

Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Off-White, Homogeneous

None Detected5-21 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Off-White, Homogeneous

None Detected5-22 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Off-White, Homogeneous

None Detected5-23 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 5 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Floor Tile, Beige, Homogeneous

None Detected5-24 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Beige, Homogeneous

None Detected5-25 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Floor Tile, Beige, Homogeneous

None Detected5-26 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Yellow, Homogeneous

None Detected Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 1 Float, White, Homogeneous

None Detected5-27 <1%

Other Non-Fibrous Material 100%

YesLAYER 2 Mastic, Black, Homogeneous

Chrysotile 3% Other Non-Fibrous Material 97%

Mastic, Sample Not Analyzed

5-28

Mastic, Sample Not Analyzed

5-29

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 6 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

Cellulose FiberNoMastic, Yellow/ Brown, Homogeneous

None Detected5-30 <1%

Other Non-Fibrous Material 100%

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White, Homogeneous None Detected5-31 2% 56%

Other Non-Fibrous Material 42%

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White, Homogeneous None Detected5-32 2% 56%

Other Non-Fibrous Material 42%

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White, Homogeneous None Detected5-33 2% 56%

Other Non-Fibrous Material 42%

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White/ Tan, Homogeneous

None Detected5-34 45% 10%

Other Non-Fibrous Material 45%

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White/ Tan, Homogeneous

None Detected5-35 45% 10%

Other Non-Fibrous Material 45%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 7 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

Cellulose Fiber Fibrous Glass

NoCeiling Tile, White/ Tan, Homogeneous

None Detected5-36 45% 10%

Other Non-Fibrous Material 45%

Cellulose FiberNoCeiling Tile, White/ Brown, Homogeneous

None Detected5-37 85%

Other Non-Fibrous Material 15%

Cellulose FiberNoCeiling Tile, White/ Brown, Homogeneous

None Detected5-38 85%

Other Non-Fibrous Material 15%

Cellulose FiberNoCeiling Tile, White/ Brown, Homogeneous

None Detected5-39 85%

Other Non-Fibrous Material 15%

Cellulose FiberNoLAYER 1 Ceiling Tile, White/ Brown, Homogeneous

None Detected5-40 85%

Other Non-Fibrous Material 15%

YesLAYER 2 Mastic, Brown, Homogeneous

Chrysotile 2% Other Non-Fibrous Material 98%

Mastic, Sample Not Analyzed

5-41

Mastic, Sample Not Analyzed

5-42

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 8 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoMastic, Beige, Homogeneous None Detected5-43 Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-44 Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-45 Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-46 Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-47 Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-48 Other Non-Fibrous Material 100%

NoLAYER 1 Cove Base, Maroon, Homogeneous

None Detected5-49 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Beige, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoMastic, Beige, Homogeneous None Detected5-50 Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 9 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Cove Base, Maroon, Homogeneous

None Detected5-51 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Beige, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Cove Base, Dark Blue, Homogeneous

None Detected5-52 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Beige, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Cove Base, Dark Blue, Homogeneous

None Detected5-53 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Beige, Homogeneous

None Detected Other Non-Fibrous Material 100%

NoLAYER 1 Cove Base, Dark Blue, Homogeneous

None Detected5-54 Other Non-Fibrous Material 100%

NoLAYER 2 Mastic, Beige, Homogeneous

None Detected Other Non-Fibrous Material 100%

Cellulose FiberNoMastic, Beige, Homogeneous None Detected5-55 <1%

Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 10 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoMastic, Beige, Homogeneous None Detected5-56 Other Non-Fibrous Material 100%

NoMastic, Beige/ Gray, Homogeneous None Detected5-57 Other Non-Fibrous Material 100%

NoLAYER 1 Painted Texture, Blue, Homogeneous

None Detected5-58 Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 2 Tape, Beige, Homogeneous

None Detected 100%

NoLAYER 3 Joint Compound, White, Homogeneous

None Detected Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 4 Wallboard, Brown/ White, Homogeneous

None Detected 10%

Other Non-Fibrous Material 90%

NoLAYER 1 Painted Texture, White, Homogeneous

None Detected5-59 Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 2 Tape, Beige, Homogeneous

None Detected 100%

NoLAYER 3 Joint Compound, White, Homogeneous

None Detected Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 4 Wallboard, Brown/ White, Homogeneous

None Detected 10%

Other Non-Fibrous Material 90%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 11 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Painted Texture, White, Homogeneous

None Detected5-60 Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 2 Tape, Beige, Homogeneous

None Detected 100%

NoLAYER 3 Joint Compound, White, Homogeneous

None Detected Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 4 Wallboard, Green/ Brown, Homogeneous

None Detected 10%

Other Non-Fibrous Material 90%

NoLAYER 1 Joint Compound, White, Homogeneous

None Detected5-61 Other Non-Fibrous Material 100%

Cellulose Fiber Fibrous Glass

NoLAYER 2 Wallboard, Brown/ White, Homogeneous

None Detected 10% <1%

Other Non-Fibrous Material 90%

NoLAYER 1 Joint Compound, White, Homogeneous

None Detected5-62 Other Non-Fibrous Material 100%

Cellulose Fiber Fibrous Glass

NoLAYER 2 Wallboard, Brown/ White, Homogeneous

None Detected 10% <1%

Other Non-Fibrous Material 90%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 12 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoLAYER 1 Joint Compound, White, Homogeneous

None Detected5-63 Other Non-Fibrous Material 100%

Cellulose Fiber Fibrous Glass

NoLAYER 2 Wallboard, Brown/ White, Homogeneous

None Detected 10% <1%

Other Non-Fibrous Material 90%

NoJoint Compound, White, Homogeneous

None Detected5-64 Other Non-Fibrous Material 100%

NoJoint Compound, White, Homogeneous

None Detected5-65 Other Non-Fibrous Material 100%

NoJoint Compound, White, Homogeneous

None Detected5-66 Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 1 Plaster, White, Homogeneous

None Detected5-67 <1%

Other Non-Fibrous Material 100%

Cellulose Fiber Hair

NoLAYER 2 Plaster, Tan, Homogeneous

None Detected <1% <1%

Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 13 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

Cellulose FiberNoLAYER 1 Plaster, White, Homogeneous

None Detected5-68 <1%

Other Non-Fibrous Material 100%

Cellulose Fiber Hair

NoLAYER 2 Plaster, Tan, Homogeneous

None Detected <1% <1%

Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 1 Plaster, White, Homogeneous

None Detected5-69 <1%

Other Non-Fibrous Material 100%

Cellulose Fiber Hair

NoLAYER 2 Plaster, Tan, Homogeneous

None Detected <1% <1%

Other Non-Fibrous Material 100%

Cellulose FiberNoParticle Board, Brown, Homogeneous

None Detected5-70 95%

Other Non-Fibrous Material 5%

Cellulose FiberNoParticle Board, Brown, Homogeneous

None Detected5-71 95%

Other Non-Fibrous Material 5%

Cellulose FiberNoParticle Board, Brown, Homogeneous

None Detected5-72 95%

Other Non-Fibrous Material 5%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 14 of 15

JH1031707J3 Order #:

VAMC - DALLAS TX - BLDG 5

1052 Hercules Drive Houston TX 77058

Micro Air of Texas Melissa Kiser

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM)

EPA 600/M4-82-020; 600/R-93/116

Asbestos (Yes/No)

Sample Description Asbestos Constituents

Sample ID # Location Non-Asbestos Constituents

J3 Resources, Inc.

6110 W. 34th Street, Houston, Texas 77092

Phone: (713) 290-0221 - Fax: (713) 290-0248

J3Resources.com

29-Jan-2010Date Reported:

NoPutty, Pink, Homogeneous None Detected5-73 Other Non-Fibrous Material 100%

NoFire Stop, Red, Homogeneous None Detected5-74 Other Non-Fibrous Material 100%

Cellulose FiberNoSealant/ Fire Stop, Cream, Homogeneous

None Detected5-75 <1%

Other Non-Fibrous Material 100%

Synthetic FiberNoSealant, Gray, Homogeneous None Detected5-76 3%

Other Non-Fibrous Material 97%

NoLAYER 1 Water Proofing, Black, Homogeneous

None Detected5-77 Other Non-Fibrous Material 100%

Cellulose FiberNoLAYER 2 Plaster, Beige, Homogeneous

None Detected <1%

Other Non-Fibrous Material 100%

Tracy Morgan Analyst

This report relates only to the materials tested. This report is for the exclusive use of the addressed client and shall not be reproduced except in full, without written approval by J3 Resources, Inc. (J3). Samples are analyzed according to EPA test methods listed above and are subject to the inherent limitations of Polarized Light Microscopy and interference of matrix components. J3 recommends TEM confirmation of non-friable organically bound materials reported as < 1% by PLM. All samples received in good condition unless otherwise noted. This report shall not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.

NVLAP Lab Code: 200525-0; AIHA Lab ID: 157714; TDSHS License: 30-0273 Page 15 of 15

VAMC DALLAS, TX

BUILDING 5 BASEMENT

ASBESTOS - CONTAINING

HOMOGENEOUS AREAS

HA-01 Steam Pipe and Fitt ing Insulation

I I, JANUARY 13, 2OIO

MICRO AIR OF TEXAS, INC.

JOB #A-1001

DRAWTNG # I

Basement

BUILDING 5 BASEMENT

ASBESTOS - CONTAINING

HOMOGENEOUS AREAS

HA-10 Black Mast ic Under Carpet tl I I r I

JANUARY 1 3, 20 1 O

MICRO AIR OF TEXAS, INC.

JOB #A- 1001

DRAWTNG # 2

A/C ROOM

B4B

Basement

BUILDING 5 1ST FLOOR

ASBESTOS - CONTAINING

HOMOGENEOUS AREAS

HA-15 Brorn Ceiling Tile Mastic (patties)

JANUARY 13, 2OIO

MICRO AIR OF TEXAS, INC.

JOB #A-1001

DRAWTNG # 3

BUILDING 5 lST FLOOR

ASBESTOS -CONTAINING

HOMOGENEOUS AREAS

HA-10 Steam Pipe and Fitting Insulation

JANUARY 13, 2O1O

MICRO AIR OF TEXAS, INC.

JOB #A- 1001

DRAWTNG # 4

BUILDING 5 zND FLOOR

ASBESTOS-CONTAINING

HOMOGENEOUS AREAS

ACCESS DOOR

HA-01 Steam Pipe and Fitting Insulation

JANUARY 13, ZOIO

MICRO AIR OF TEXAS, INC.

JOB #A- r001

DRAWING # 5

SECTION III

SECTION III - ACM Material Assessment and Quantification

Each area where ACM was identified in the asbestos management plan was visually inspected and assessed as to physical condition and potential for airborne asbestos fiber release.

Included in the assessment factors are such items as friability, accessibility, amount of current damage, amount of airflow, vibration, or abrasion to which the material is subject, potential for water damage, type and number of personnel normally located within each homogeneous sampling area, proximity to normal maintenance activities and potential for disturbance of such materials under normal operating conditions, potential for deterioration, and overall health risk of the material.

Final hazard assessment ratings are based upon the system designed in the EPA AHERA protocol for asbestos building inspectors. The material assessment categories in order of decreasing critical importance are as follows:

1. Damaged or Significantly Damaged TSI ACM