SATPC0039973 Tab 04 Drawing 6 (FLL-HPROJ-0012_-).pdf
PDF 186 KB Posted
- Attached to
- Strongback Fabrication
- Solicitation number
- 80NSSC25918799Q
About this file
This document is an engineering drawing for a Floor Plate Doubler, created by NASA's Armstrong Flight Research Center. The technical drawing specifies a steel component (ASTM A36) with precise dimensional requirements, including hole placements, tolerances, and surface treatments. Key manufacturing specifications include:
Material and Finish Requirements:
- Surface roughness of 125 microinches maximum
- Primer/topcoat finish per MIL-DTL-18264:
- One coat of MIL-PRF-23377 epoxy primer
- Two coats of MIL-PRF-85285 polyurethane in OSHA Safety Blue
- Human-readable identification marking per MIL-STD-130 using permanent ink
- Dimensioning and tolerancing per ASME Y14.5-2018
The document is marked as CUI//SP-EXPT (Controlled Unclassified Information/Special Export) and carries an EAR99/NLR (No License Required) export classification, indicating it contains technical information with specific handling requirements.
View the file
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
7 6 5 4 3
B B
C C
7 6 5 4 2
2 1
A
8 3
D
A
D
NOTES - UNLESS OTHERWISE SPECIFIED:
1.000
4X R.500
8X .688 +.008 -.001
THRU
4X .563-18 UNF-2B THRU
8X 1.500 +.010 -.010
.560
1.557
.000
1.819
3.562
5.195
6.571
2.933
X
X
8X R.063 MAX
(9.504)
REVISION HISTORY
CHECKENGRDATEDESCRIPTIONREV
2025-09-08APPROVED FOR INITIAL RELEASE -
SHEET 1 OF 1CI NO. SCALE: 0.500
-FLL-HPROJ-00121JYR2D
REV.DWG. NO.CAGESIZE
FLOOR PLATE DOUBLER
TITLE
NATIONAL AERONAUTICS AND SPACE ADMINISTRATION
ARMSTRONG FLIGHT RESEARCH CENTER
EDWARDS, CALIFORNIA
2025-04-16A.C. HOLGUINENGR
2025-09-04C.A. MASELLACHECK
REVIEW
2025-09-08L.D. HUDSONREVIEW
2025-04-16A.C. HOLGUINDRAWN
2025-04-16A.C. HOLGUINDESIGN
DATEAPPROVALS
THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
DECIMALS
.X .1
.XX .03
.XXX .010
.XXXX .0010
ANGLES
.X 0.5
.XX 0.25
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN INCHES. TOLERANCES ARE:
PARTS SHALL BE FREE OF
BURRS AND SHARP EDGES
INTERPRET DRAWING PER
ASME Y14.100
USED ONNEXT ASSEMBLY
FLLFLL-HPROJ-0003
PARTS LIST
NOTES
MATERIAL
SPECIFICATION
NOMENCLATURE
OR DESCRIPTION
PART OR
IDENTIFYING NO.
CAGE CODE
ITEM
NO.QTY REQD
.018 1.25 A
.062 A B
.020 A C
8X INDIVIDUALLY
8X INDIVIDUALLY
-101 FLOOR PLATE DOUBLER DETAIL
1. MATERIAL: STEEL ASTM A36
2. SURFACE ROUGHNESS ON MACHINED SURFACES SHALL BE 125
MICROINCHES MAX
3. PRIMER/TOP COAT FINISH PER MIL-DTL-18264 AS FOLLOWS:
A. ONE COAT MIL-PRF-23377 EPOXY PRIMER, TYPE I, CLASS
C1, C2, or N
B. TWO COATS MIL-PRF-85285 POLYURETHANE, TYPE II,
COLOR 15092 (OSHA SAFETY BLUE) PER SAE INTERNATIONAL
SPECIFICATION AMS-STD-595
C. MASK HOLES PRIOR TO PRIMER AND PAINT
4 APPLY HUMAN-READABLE IDENTIFICATION MARKING PER MIL-
STD-130 BY HANDWRITTEN, PERMANENT INK. USE 0.5 INCH
CHARACTER HEIGHT. LOCATE APPROXIMATELY AS
SHOWN. MARKING SHALL READ AS FOLLOWS:
"1JYR2-FLL-HPROJ-0012-101" AND LATEST REVISION
5. UNLESS OTHERWISE SPECIFIED ALL SURFACES:
.063 A B
6. INTERPRET DIMENSIONING AND TOLERANCING PER
ASME Y14.5-2018
.010
SECTION A-A
.010 A B
-101 FLOOR PLATE DOUBLER
ISOMETRIC VIEW
SCALE: NONE
CONTROLLED BY: A.C. HOLGUIN, AFRC, NASA
CUI//SP-EXPT
REVIEWED FOR CUI BY: A.C. HOLGUIN, AFRC, NASA
(EXCEPT FOR EXPORT CONTROL)
The information contained in this document is technical in content, but not technical data as defined by the International Traffic in Arms Regulations (ITAR) or the
Export Administration Regulations (EAR), and therefore is designated as EAR99/NLR, (No License Required). General Prohibition Six (Embargo) applies to all items subject to the EAR, (i.e. item on the CCL and within EAR99/NLR). You may not make an export or re-export contrary to the provisions of part 746 (Embargoes and Other Special Controls) of the EAR and 22 CFR §126.1 of the ITAR.
EAR99/NLR NOTICE
A
B
C
Carla Masella Full Size
| Sheet 1 |
| Views |
| new_view_4 |
| right_5 |
| new_view_6 |
| Zones |
| D8 |
| D7 |
| D6 |
| D5 |
| D4 |
| D3 |
| D2 |
| D1 |
| C8 |
| C7 |
| C6 |
| C5 |
| C4 |
| C3 |
| C2 |
| C1 |
| B8 |
| B7 |
| B6 |
| B5 |
| B4 |
| B3 |
| B2 |
| B1 |
| A8 |
| A7 |
| A6 |
| A5 |
| A4 |
| A3 |
| A2 |
| A1 |
File details come from the government source that posted it. Updated .