1339AS Drawings Addenda.pdf

FOR MOBILE FACILITIES PN’S 1339ASAS500‐1, 1339AS501‐1 & 1339AS1000‐1 THE POWER

INPUT CONNECTORS (PART OF THE POWER INPUT PANEL ASSEMBLY) FN’S 15, 16 & 17 ON

DRAWING 1339AS383 SHALL NOT BE INSTALLED. THESE CONNECTORS SHALL BE INCLUDED IN

THE SHIP LOOSE ITEMS LISTED IN NOTE 1 ON DRAWINGS 1339AS500, 1339AS501 &

1339AS1000

1339AS349 –

sheet 1 ‐ delete FN 10 from Note 1 ‐ add the following as FN 26 to the bill of materials on sheet 1 MIL‐S‐81733, Type 4 Sealant add the following as note 2: “Apply a bead of sealer, FN 26, around the edges of

FN 10

sheet 2 sec a‐a change FN 19 to FN 26 and add note 2

1339AS500

install safety tape (PN 1339AS96‐1) at bottom of both end doors the same as FN 86 is shown on sheet 4 of drawing 1339AS700 and at the top of both end doors as FN 86 is shown on sheet 6 of drawing 1339AS700

1339AS1241

sheet 2 ‐ add overall height dimension of 46.75

The following drawings have been revised since the Data Lists (DL1339AS100, DL1339AS101, DL1339AS500, DL1339AS501, DL1339AS700, DL1339AS701, DL1339AS900‐2, DL1339AS1000, DL1339AS1101) have be last updated:

1339AS203 revision E 1339AS362 revision H 1339AS423 revision D 1339AS453 revision A 1339AS950 revision D 1339AS962 revision E 1339AS1279 revision – 1339AS1280 revision ‐ WL1339AS740 revision H WL1339AS741 revision H WL1339AS947 revision F

The dawning revision listed above shall be used instead of the drawing revision listed in the Data Lists.

1339AS353 and 1339AS624 – all open sides of forklift pocket straps shall be sealed with 1339AS208 sealer, the edge of the two baseframe “Z” members (in th length direction of the Mobile Facility) where the mate with the corner longitudinal shall be covered with 1339AS208 sealer as shown below:

Z -M E M B E R S E A L E R

1339AS700

sheet 1 – change PN of FN 42 from “1339AS806‐2” to “1339AS950‐4” sheet 2 ‐ change PN of FN 97 from “WS896/2‐08A” to “WS896/2‐08A‐G” sheet 2 ‐ change PN of FN 98 from “1339AS950‐2 to “1339AS950‐5”

1339AS701

sheet 2 – change PN of FN 93 from “1339AS50‐1” to “1339AS950‐5, change qty from “1” to “2” sheet 2 ‐ change PN for FN 111 from “WS896/2‐08A” to “WS896/2‐08A‐G” sheet 2 ‐ change PN for FN 112 from “WS896/2‐08A” to “WS896/2‐02A‐G” sheet 2 – delete FN 116 sheet 9 – change balloon (near S7) from “116” to “93”

1339AS783

sheet 1 – change thickness from “.250” to “.125”

1339AS900

sheet 1 – change qty of FN 57 from “1339AS950‐2” to 1339AS950‐5” sheet 1 ‐ change PN for FN 36 from “1339AS923‐1” to “1339A1280‐1” sheet 2 – change qty of FN 66 callout from 4 to 3 for 1339AS900‐2 sheet 2 – add the following as FN 77 Qty 1 PN 1339AS950‐4 sheet 2 ‐ change PN for FN 84 from “WS896/2‐08A” to “WS896/2‐08A‐G” sheet 2 – change PN for FN 100 from “MS227183‐12” to “MS27183‐12” sheet 7 – left side of drawing change:

“.413 ‐ .423 dia 3 holes marked A” to “.413 ‐ .423 dia 11 holes marked A” “.413 ‐ .423 dia 1 hole marked B” to “.413 ‐ .423 dia 4 holes marked B” on lighting panel (FN 36) delete hole marked “B” sheet 9 – change FN 66 callout (near S2 callout) to FN 77

WL1339A740

Change QTY of FN 12 from “70 FEET” to “80 Change QTY of FN 26 from”7” to “9”

Add the follow two wire two ground the three way light switches:

WIRE

NO.

FIND

NO.

COLOR LENGTH

FEET

FROM WIRE

TERMINATION

TO WIRE

TERMINATION

115 12 GRN 5 DS5‐GRD MS25036‐156 S4‐GRD STRIP

116 12 GRN 5 DS2‐GRD MS25036‐156 S3‐GRD STRIP

WL1339AS741

Change QTY of FN 14 from “108 FEET” to “133” Change QTY of FN 40 from ”13” to “15”

Add the follow two wire t0o ground the two three way light switches and one two way switch:

WIRE

NO.

FIND

NO.

COLOR LENGTH

FEET

FROM WIRE

TERMINATION

TO WIRE

TERMINATION

182 14 GRN 8 DS8‐GRD MS25036‐156 S7‐GRD STRIP

183 14 GRN 8 DS5‐GRD MS25036‐156 S16‐GRD STRIP

184 14 GRN 9 DS5‐GRD STRIP S6‐GRD STRIP

WL1339AS947

Change QTY of FN 15 from “50 FEET” to “60 Change QTY of FN 23 from”7” to “9”

Add the follow two wires to ground the three way light switches:

WIRE

NO.

FIND

NO.

COLOR LENGTH

FEET

FROM WIRE

TERMINATION

TO WIRE

TERMINATION

222 15 GRN 5 DS4‐GRD MS25036‐156 S2‐GRD STRIP

223 15 GRN 5 DS1‐GRD MS25036‐156 S1‐GRD STRIP