36C24218B0125-0003002.pdf

Renovate 6th Floor Mental Health Project 526-13-102

10 51 00-1

SECTION 10 51 16

WOOD LOCKERS

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Wood Lockers:

1. 15-inch wide designer wood lockers.

1.2 RELATED SECTIONS

A. Section 06 10 00 - Rough Carpentry.

B. Section 09 65 13 - Resilient Base and Accessories.

1.3 REFERENCES

A. ADAAG - Americans with Disabilities Act, Accessibility

Guidelines.

B. IBC - International Building Code.

1.4 SUBMITTALS

A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT

DATA, AND SAMPLES.

B. Product Data: Manufacturer's data sheets on each product to be used, including:

1. Preparation instructions and recommendations

2. Storage and handling requirements and recommendations.

3. Installation methods.

C. Shop Drawings: Prepared specifically for this project; show dimensions of lockers and interface with other products.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Manufacturer shall have a Quality

System in place to ensure and be able to substantiate that manufactured units conform to requirements and match the approved design and must be ISO 9001: 2015 certified.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

B. Storage and Protection: Locker components shall be stored flat, 10 51 00-2 if shipped unassembled, until assembly. Store materials protected from exposure to harmful environmental conditions and at temperature and humidity conditions recommended by the manufacturer.

1.7 WARRANTY

A. Manufacturer's Standard Warranty: Repair or replace components of locker products that fail in materials or workmanship within 3 years from date of Substantial Completion.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturers:

1. WB Manufacturing Co.: 507 Grant Street, Thorp, WI 54771; Toll

Free Tel: 800-242-2303; Email: info@wibenchmfg.com.

2. Hallowell, 2823 West Orange Avenue, Apopka, FL 32703; Toll Free

Tel: 866-566-0500; Email: woodlockers@hallowell-list.com.

3.Salsbury Industries: 1010 E. 62nd St.; Los Angeles, CA

90001-1598; Toll Free Tel: 800-LOCKERS (800-562-5377); Tel:

323-846-6700; Fax: 800-562-5399; Email: Salsbury@lockers.com;

Web: www.lockers.com.

2.2 15-INCH WOOD LOCKERS

A. 15-Inch Wide Designer Wood Locker Series:

1. Double-tier.

B. Features:

1. Unit Width: 15 in (381 mm).

2. Unit Height: 76 in (1,930 mm) with bases.

3. Unit Depth: 15 in (457 mm).

4. Laminate Finish: Cherry.

C. Interior Equipment:

1. Standard Hardware Features:

a. Double Tier Wood Lockers:

1) Padlock hasp.

2) One top-mounted, two-pronged stainless steel coat hook.

10 51 00-3

3) One 5 in (127 mm) deep shelf.

4) Two heavy duty concealed door hinges.

D. Optional Equipment:

1. Sloping Hoods: 45 in (1,143 mm) for 3-wide units.

2. Bases: 4 in (102 mm) high.

3. Sloping Hood Fillers: Sloping in-line top fillers.

4. Sloping Hood Fillers: Sloping corner fillers.

5. Front Fillers: 9 in (229 mm) wide filler panels.

6. Front Fillers: Vertical corner fillers.

7. Single End Side Panels: With sloping hoods.

8. Keyed padlocks.

9. Engraved name/number plates.

E. Customizations:

1. Coat Rod: Additional garment storage capability.

F. Construction:

1. Locker Body: Precision machined with faces flat and free of scratches and chips.

a. Locker shall be fabricated using doweled and glued assembly process.

b. Tops and bottoms with three sides formed to 90 degrees, the front offset formed to be flush with horizontal frame member.

c. Shelves with four sides formed to 90 degrees.

2. Locker Doors: Precision machined with faces flat and free of scratches and chips.

a. Doors have four radial edges.

b. Routed inset to insert and attach number plates.

c. Ventilation: 1/2 in (13 mm) opening between door and frame on locker top and bottom.

d. Single-Point Latching:

1) Recessed handle in door.

2) Integral Pocket and Pull: 22 gauge powder coated stainless steel securely fastened to door with two lugs and a positive tamper-resistant decorative fastener.

a) Pocket Depth: Prevent a combination padlock, 10 51 00-4 built-in combination lock, or key lock from protruding past door face.

b) Pull: Formed in pocket.

c) Padlock Staple: Protruding through pocket.

3) Provide lock hole cover plate for use with padlocks.

4) Locking Device: 11 gauge steel latch attached to locker frame;

5) Firmly secure rubber silencers to locker frame.

3. Fabricate corners and fillers as required for installation.

4. Unit Assembly: May require minor assembly.

PART 3 EXECUTION

3.1 EXAMINATION AND PREPARATION

A. Do not begin installation until substrates have been properly prepared. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

B. Clean surfaces thoroughly prior to installation.

3.2 INSTALLATION

A. Install in accordance with manufacturer's installation instructions, approved submittals, and in proper relationship with adjacent construction. Anchor the units to the wall studs through the locker back and to the floor.

3.3 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair or replace damaged products before Substantial

Completion.

- - - END - - -