Building_247_Furniture_Package-Final_September_19_2019.pdf

F U R N I T U R E S P E C I F I C A T I O N S

ATC Building 247 Furniture Design Portsmouth, NH

Prepared For:

USPFO, NH National Guard Joint Contracting Office 302 Newmarket St.

Bldg 145 Room 218 Pease ANGB, NH 03803-0157

19 September 2019

Prepared By:

Table of Contents

STATEMENT OF WORK Section 1

INSTRUCTIONS TO BIDDERS Section 2

PRODUCT SPECIFICATIONS Section 3

Seating Tables Lectern Storage & Filing Workstations Casegoods Accessories

PRODUCT BY LOCATION Section 4

PRODUCT SUMMARY Section 5

FLOOR PLANS / DRAWINGS Section 6

STATEMENT OF WORK Section 1

STATEMENT OF WORK

I. INTRODUCTION:

a. The New Hampshire National Guard (hereinafter referred to as the Owner) invites interested parties to submit sealed bids for the purchase of office and conference, furniture for the ATC Building 247 located at 302 Newmarket Street, Newington, Pease

ANGB, NH 03803-0157. All questions pertaining to bid documents should be directed in writing to the Contracting Specialist as referenced in the solicitation.

II. SPECIFIC TASK:

a. PROJECT MANAGEMENT: The contractor will coordinate with all suppliers to ensure the installation of all equipment. This includes all required permits to state and federal code.

III. PERSONNEL:

a. The Contractor shall furnish all personnel to accomplish the work required by this contract. The Contractor shall ensure that all personnel have completed a required training program. The training program will be defined by the Contractor. The contractor shall provide, employ and pay the established Service Contract Act wages to all personnel required to accomplish this contract.

b. Program Manager (PM): The contactor shall designate a PM who shall ensure performance under this contract. The name of this person, and an alternate who shall act for the contractor when the PM is absent, shall be designated in writing to the KO.

The PM or alternate shall have full authority to act for the contractor on all contract matters relating to daily operation of this contract. The PM shall work through the

Contract Specialist or KO, to resolve issues, receive technical instructions, and ensure adequate performance of services. The PM shall ensure that contractor employees do not perform any services outside the scope of the contract without an official modification issued by the KO. The PM shall ensure contractor employees understand that services performed outside the scope of the contract are performed wholly at the expense of the contractor.

IV. DEFINITIONS AND ACRONYMS:

a. CONTRACTOR. A supplier or vendor awarded a contract to provide specific supplies or service to the government. The term used in this contract refers to the prime.

b. CONTRACTING OFFICER (KO). A person with authority to enter into, administer, and or terminate contracts, and make related determinations and findings on behalf of the government. Note: The only individual who can legally bind the government.

c. CONTRACTING OFFICER'S REPRESENTATIVE (COR). An employee of the U.S.

Government designated by the KO to monitor contractor performance. Such appointment shall be in writing and shall state the scope of authority and limitations.

This individual has authority to provide technical direction to the Contractor if that direction is within the scope of the contract, does not constitute a change, and has no funding implications. This individual does NOT have authority to change the terms and conditions of the contract.

d. DELIVERABLE. Anything that can be physically delivered and includes non-manufactured things such as meeting minutes or reports.

e. PHYSICAL SECURITY. Actions that prevent the loss or damage of Government property.

f. QUALITY ASSURANCE. The government procedures to verify that services being performed by the Contractor are performed according to acceptable standards.

g. QUALITY CONTROL. All necessary measures taken by the Contractor to assure that the quality of an end product or service shall meet contract requirements.

h. SUBCONTRACTOR. One that enters into a contract with a prime contractor. The

Government does not have privity of contract with the subcontractor.

i. WORKDAY.

i. Schedule normal work by Contractor and Subcontractor personnel between the hours of 7:00 AM and 4:00 PM, Monday through Friday, excluding Federal holidays. If the Contractor desires to work during periods other than above, submit a written request (e-mail is acceptable) for each such occurrence to the

Contracting Officer at least 3 working days in advance of the proposed event, so that the Government may make special inspection and/or security arrangements. The Contracting Officer may decline approval. Contractor may have to work outside the normal work schedule in order to make utility connects; when this occurs, contractor shall adjust the work schedule or pay overtime. There will be no change associated with the change in schedule.

ii. Any work at the Government site shall not take place on Federal holidays or weekends unless directed by the Contracting Officer (KO). However, if required, the KO may designate the Contractor to work during holidays and weekends.

iii. There are ten (10) Federal holidays set by law (USC Title 5 Section 6103) that

The National Guard follows:

1. Under current definitions, four are set by date:

• New Year's Day January 1

• Independence Day July 4

• Veterans Day November 11

• Christmas Day December 25

2. If any of the above falls on a Saturday, then Friday shall be observed as a holiday. Similarly, if one falls on a Sunday, then Monday shall be observed as a holiday.

iv. The other six are set by a day of the week and month:

• Martin Luther King's Birthday - Third Monday in January

• Washington's Birthday - Third Monday in February

• Memorial Day - Last Monday in May

• Labor Day - First Monday in September

• Columbus Day - Second Monday in October

• Thanksgiving - Fourth Thursday in November

V: FACILITIES

a. Utilities: All utilities in the facility will be available for the contactor’s use in the performance of this contract. The contractor shall instruct employees in utilities conservation practices. The contractor shall operate under conditions that preclude the waste of utilities, which include turning off the water faucets or valves after using the required amount.

VI: SECURITY:

a. GENERAL

i. All Contractor employees, including subcontractors, and subcontractors’ employees, suppliers, and suppliers’ employees shall be required to comply with the Installation Security Requirements regarding personnel, vehicle, and equipment security passes and access the jobsite. Nothing in the contract shall be construed in any way to limit the authority of the Commanding Officer to prescribe new, or to enforce existing security regulations governing the admission or exclusion of persons and the conduct of persons while on base, including but not limited to, the rights of search of all persons or vehicles on base.

ii. Contractor employees shall conduct themselves in a proper, efficient, courteous and businesslike manner. Remove from the site any individual whose continued employment is deemed by the Contracting Officer to be contrary to the public interest or inconsistent with the best interests of National Security.

iii. The Contractor is expected to become fully acquainted with, and strictly adhere to Readiness regulations affecting the performance of this Contract. Parts of the regulations pertaining to fire prevention, driving safety, restricted areas, sanitation, disposal of debris and pollution control may apply to this project.

b. COORDINATION

i. Coordinate with the Contracting Officer for specific security and access requirements.

ii. Access to Buildings/ Occupied Buildings: The Contractor may work in or around existing occupied buildings. The Contractor is responsible, via the Contracting

Officer, to obtain access to building and facilities and arrange for them to be opened and closed. Do not enter the building(s) without prior approval of the

Contracting Officer. Keep the existing buildings and their contents secure at all times. Provide temporary closures as required to maintain security. Contract personnel will not be permitted in security-regulated buildings or areas unless cleared by the Security Officer.

iii. The installation of the equipment shall be coordinated with the site supervisor or

Contracting Office 14 days prior to delivery.

C. CONTRACTOR VEHICLES

i. All vehicles shall display a valid state license plate and safety inspection sticker, if applicable, and shall be maintained in good repair. The company name shall be displayed in a clearly visible manner and size on each Contractor vehicle used in the course of work. Registration and proof of insurance shall be kept in the vehicle, and drivers shall be properly licensed.

D. SECURITY REQUIREMENTS:

i. All security requirements apply to all subcontractors and suppliers associated with this contract. Comply with the following:

1. Do not publicly disclose any information concerning any aspect of the materials or services relating to this contract, without prior written approval of the Contracting Officer.

2. Do not disclose or cause to be disseminated any information concerning the operations of the activity’s security or interrupt the continuity of its operations.

3. Do not disclose any information to any person not entitled to receive it.

Failure to safeguard any classified information that may come to the

Contractor or any person under his control, may subject the Contractor, his agents or employees to criminal liability under 18 U.S.C., Sections 793 and

798.

4. Direct to the Contracting Officer for resolution all inquiries, comments or complaints arising from any matter observed, experienced, or learned as a result of or in connection with the performance of this contract, the resolution of which may require the dissemination of official information.

5. Coordinate photography requirements with the Contracting Office. Some areas restrict or prohibit photographing Government property.

6. Deviations from or violations of any of the provisions of this paragraph, will, in addition to all other criminal and civil remedies provided by law, subject the Contractor to immediate termination for default and withdrawal of the

Government’s acceptance and approval of employment of the individuals involved.

E. IDENTIFICATION OF CONTRACTOR PERSONNEL

i. All Contractor personnel, including subcontractors, will wear a brightly colored reflective safety vest (ANSI Class 1 or better) while at the job site or visiting other areas of the base as may be required to complete the work.

INSTRUCTIONS TO BIDDERS Section 2

INSTRUCTIONS TO BIDDERS

I. BID SPECIFICATIONS

a. Bid specifications can be found in the "Product Specifications" section (Section 3), categorized by furniture type (i.e. storage, seating, tables). This bid package also includes a “Product Summary” section that lists all furniture (again, categorized by furniture type) and the quantity for each. Specific brands are listed in this summary but are not to be construed as restricting other products of comparable or superior quality. Brand listed items are for Basis of Design only. The Owner reserves the right to waive a specification it deems not to be essential. The “Product by Location” section includes specific furniture for each area/space, as well as the quantity for each area. Furniture plans for each section can be found in Section 4 of this package. All bids must show unit pricing and be totaled on the bid form provided. All freight, delivery and inside installation should be shown as a separate cost.

b. No state sales tax will be charged, and Federal Excise Tax Exemption Form will be executed by The New Hampshire National Guard after award of the bid.

II. ALTERNATIVES / SUBSTITUTIONS

a. Each bidder represents that his/her bid is based upon the materials and equipment described in the "Furniture Specification Bid Form." Any alternates/substitutions must be identified in writing on the vendor’s bid. The items selected were specified to achieve design aesthetics and quality desired for the project. Any alternates will be evaluated for design/quality appropriateness and may be refused on this basis.

III. DELIVERY AND COMPLETION DATE

a. Based on current construction schedule, all materials must be delivered, set-up and installed 90 days after receipt of contract award. Off-site removal of all trash related to the furniture delivery (boxes, packing materials, etc.) will be the responsibility of the bidder. Delivery dates are to be coordinated by the successful bidder(s) with the Owner. If there are any unusual conditions relating to delivery dates for the furniture, they must be clearly stated in the bid.

IV. MANUFACTURER WARRANTIES

a. Copies of manufacturer warranties shall be submitted with the bid. The selected dealer(s) shall be responsible for warranty labor for a minimum of 1 year or the time stated in the manufacturer's written warranty, whichever is longer.

PRODUCT SPECIFICATIONS Section 3

Seating Tables Lectern Storage & Filing Workstations Casegoods Accessories

SEATING

KIMBALL / Joya Chair

CH-1 26.25”w x 23”d x 43.25”h

High-performance, long-term seating with a full complement of adjustments; for computer work, general office work, and casual or formal meetings.

Basic Syncro-tilt 1-position lock control

Back: Standard black mesh

Adjustable lumbar support

Seat: Upholstered grade 3 fabric; 3” molded, CFC-free, urethane foam applied over plywood with sewn-upholstered seat and waterfall front edge.

2D arms – height adjustable with front to back adjustable arm pads, black; soft, self-skinning polyurethane foam molded over a steel core.

Black hard dual wheel casters

Black frame

Five prong black base

Fabric: To be selected

KIMBALL / Joya Side Chair

CH-2 21”w x 22.75”d x 33”h

Mobile, flexible, and refined side chair. This chair is ideal for a variety of office spaces, from multipurpose rooms to individual workstations.

Back: Standard black mesh

Seat: Upholstered grade 3 fabric; 2” molded, CFC-free, urethane foam applied over plywood with sewn-upholstered seat and waterfall front edge.

Black polyurethane arms

Carpet glides

Black frame

Fabric: To be selected

KIMBALL / Event Stacking Chair

CH-3 23.5”w x 21”d x 32”h (with arms) CH-4 19.75”w x 21”d x 32”h (without arms on casters)

Stacking chair shall have four‐leg straight base

Lightweight and mobile, and capable of stacking up to 6‐chairs high

Back: 3⁄4"-thick foam for the inside back and 1⁄4" thick foam for the outside back both fabric covered. Back secured to the frame with 4 countersunk flat-head screws, 11-gauge steel plates, and T-nuts. Flair back model constructed using 7-ply, molded plywood.

Seat: High resilience, CFC free polyurethane foam. Seat cushion is 11⁄4" thick, waterfall front edge, fabric covered. Seat is contoured, blow-molded polyethylene.

Channels within the seat pan fit over the cross members. Seat pan is attached to the seat frame with four machine screws and T-nuts.

Arms: Injection molded nylon and attached to the frame with a pressure fit.

Frame: 7⁄8" diameter, 14-gauge tubular steel. Cross members are 3⁄4" diameter, 14-gauge steel. Leg frames are joined to the cross members with metal inert gas

(MIG) welds. Color platinum metallic.

Chair glides.

Fabric to be selected from grade 1

KI INC / Apply Café Stool with low 6” back

ST-1 18.75”w x 24”d x 30”h

Frame: Legs are formed from ¾” OD x 13-gauge tubular steel. The seat plate is formed from 12-gauge steel and reinforced with 7/16” diameter wire crossmembers. All joints are welded. The frames are baked-on electrostatically-applied 30 degree gloss epoxy powder coating. An injection-molded polypropylene shroud finishes the underside of the assembly. Stool frames have an added foot ring made of 1/2" diameter steel wire and swivel glides.

Shell: One-piece contoured wood shell is constructed of formed plywood, .460”-

.480” thick, 7-ply maple and poplar construction. Top/bottom and front/ back surfaces are vertical grade postforming, product type 335, high-pressure laminate thickness of .028”. Standard finish is #38 or #60 with a sanded, waxed edge. The wood shell is supported by four plywood circular disks and ¼ -20 t-nuts bonded with construction-grade adhesive and fastened to a variety of base structures with four ¼ -20x1/2” thread-locking screws.

Finish laminate: to be selected.

TABLES

KIMBALL / Dock Meeting Table

T-1 120”w x 48”d x 28”h T-2 72”w x 36”d x 28”h (no power/data)

Tops: Racetrack table with two E2X power/data centers with factory installed cutouts and metal vertical cable manager and horizontal cable management

One piece, HPL Laminate top with self-edge rim (color to be selected).

Base: Blade Y single column 2 3⁄8"diameter, 10-gauge tubular steel with a cast aluminum foot with glides. Finish polished aluminum

FALCON / 79ST Series Standing Height Community Table

T-3 60”w x 24”d x 42”h

Tops: HPL Laminate top with self-edge rim.

Base: Powder coated tubular steel with glides.

Finishes: To be selected

KIMBALL / Xsede Height Adjust Table

T-4 60”w x 23”d x adjustable sit to stand

Base: T-leg base adjusts in height from 24 3⁄4"–41 1⁄8" using up down switch. Leveling glides, providing 1⁄2" adjustment.

Top: 1 13⁄16"-thick high-pressure laminate (HPL)

Safety: Anti-collision function on control box will engage when a firm obstruction is detected and will stop worksurface travel.

Overheat protection will stop the unit should the motor overheat.

Overload protection detects if the load is too heavy and will stop the unit.

Control box includes a 9' power cord with two-prong plug.

Laminate and base color to be selected.

HERMAN MILLER / Resolve Input Height Adjustable Table

T-5 31”w x 22”d x adjustable height 22-32”

Model: R2600

Base: Pin leg adjustable, silver

Black Casters: Two locking, 2 non-locking

Holds 25 pounds

Top: ¾ “ formcoat, eased front edge

Top finish to be selected

NATIONAL / Staccato Side Table

T-6 24” dia x 21”h

Base: Platinum metallic round

Top: HPL

Top finish to be selected

Lectern

KI All Terrain Mobile Instruct Lectern

LEC 22”w x 22”d x 45”h

The tower has two adjustable metal shelves, two accessory slots and steel, keyed door

Landing pad: 3/4"HPL laminate with 74P edge, this surface is raised 3-3/4" above the top of the storage tower with aluminum side.

Casters: four outrigger casters (two locking) Laminate surfaces with aluminum painted base. Colors to be selected.

STORAGE & FILING

HERMAN MILLER / Meridian Storage Cases

CAB-1 36”w x 18”d x 72”h

Versatile metal storage cases with base, adjustable shelves, arc handles and lock.

Smooth steel finish – paint color to be selected.

12-year, 3-shift warrantee

KIMBALL / Lateral File Cabinet

FC-1 4-draw 36”w x 18”d x 39”h

Four-draw lateral file construction features coach seam welds. Right angle bend of the coach seam makes the strongest use of formed metal and presents a clean exterior with no exposed welds.

Progressive slide suspension provides smooth drawer operation.

Steel drawer interiors are prepainted cinder.

Letter and legal filing is accommodated with conventional or hanging folders.

Side-to-side legal or letter filing can be accommodated with file bars that ship standard in file.

Front-to-back filing can be accommodated by ordering the appropriate number of front-to-back file bars separately.

Lock

Leveling floor glides

Smooth steel finish group 1 – paint color to be selected.

WORKSTATIONS

KIMBALL/ Interworks EQ Office System with Footprint Worksurfaces, Supports and Storage

WS-1 through WS-4 Workstation Sizes Vary

(Images similar but not exact)

The Interworks EQ Panel System provides components to build workstations as shown on plans including frames, fabric panels, marker board tiles and framed glass tiles, wall and worksurface supports, electrical and cable management/base wireway components and power poles and all necessary assembly connections.

Panels: Tackable acoustical panels are 2" thick and fabric covered. Grade A wall panel models include: Top cap, Wireway covers, Panel hinges, Glides and carpet grippers

Panels: Tackable sectional panels are 2” thick with fabric sectional tiles and glass sectional tiles with a 2 7⁄8" extruded aluminum frame with 1⁄8" tempered glass; available clear or frosted.

Frame: Panel frame is constructed of 11⁄4" steel tubing. Panel interior has two sheets of 1⁄4" thick fiberglass that are held in place at the top and bottom with a horizontal rail.

Side rails provide slots at 1" increments for mounting components.

Top Cap: Aluminum painted

Wireway Covers: Steel painted

Full-Height End Trim: Plastic

Panel Hinge: Polypropylene

Acoustical Ratings: NRC rating = .65 STC rating = 15

*Narrate panel system can be used in place of Interworks EQ panel system

Power distribution assembly, factory-installed in the base wireway of 24”W and wider powered panels, allows distribution of power. 18”W panels provide no power or data access, but can pass power to adjacent panels.

Base wireway can accommodate up to 8 1⁄4"-diameter data cables at 40% fill or up to 12 at 60% fill. The capacity from panel to panel is 11 at 40% fill or 16 at 60% fill. Capacity is based on 1⁄4"-diameter (nominal) Cat 5 or Cat 6

(4-pair UTP) cables. Data cables can also be run from the base to the mid-wireway. Provide 2 data and 4 power outlets.

The Footprints Worksurfaces and Support line and traxx provides components to build workstations as shown on plans including worksurfaces, above storage, filing units, wall and worksurface support brackets, lighting, tackboards/accessories and all necessary assembly connections.

Worksurface thickness: 1 3/16"

Surface Material: High-pressure laminate (HPL) with cable management grommet

Rims: Vinyl

End support panel: HPL

BBF and FF: Metal, mobile on 4 non-locking casters with one counterweight and lock

Flipper Door Overhead Storage: Painted metal, receding locking doors with LED task light

Fabric covered tack board grade 2

WS-1 Work Bench: Varies in width x 24”d (18” deep at mail sorter area)

Straight workstation configuration either wall or panel mounted including mobile BBF, overhead storage, task light and fabric tack board length of overhead storage. See plans for panel locations and heights.

WS-2 Adjustable Height Work Bench: 60”w x 23”d x adjustable sit to stand

Straight workstation configuration with electric height adjustable worksurface. Includes mobile BBF, overhead storage, task light and fabric tack board length of overhead storage. See plans for panel locations and heights.

WS-3 L-Shaped Workstation: 6’-0” x 6’-0”

L-Shaped workstation configuration either wall or panel mounted including mobile BBF and FF, overhead storage, task light and fabric tack board length of overhead storage, end support panels, flat and cantilever brackets. See plans for panel locations and heights.

WS-4 L-Shaped Workstation: 6’-0” x 8’-0”

L-Shaped workstation configuration either wall or panel mounted including mobile BBF and FF, overhead storage, task light and fabric tack board length of overhead storage, end support panels, flat and cantilever brackets. See plans for

KIMBALL/ NARRATE Office System with Footprint Worksurfaces & Supports

WS-5 through WS-7 Workstation Sizes Vary

The Narrate System provides components to build workstations as shown on plans including frames, fabric panels, marker board tiles and framed glass tiles, sliding doors, wall supports, electrical and cable management/base wireway components and power poles and all necessary assembly connections.

Panels: 3 1/4” thick

Frames include: Mid-frame supports at the 2-high position, glides, attachment hardware

Base-wireway frames are available in powered and non-powered models and feature painted base-wireway covers. Powered models include the power harness.

Mid-frame supports are standard at the 2-high position to provide support for worksurfaces.

Vertical frame: 16 gauge cold-rolled steel, black

Horizontal frame: 14 gauge coldrolled steel, black

Connections: Frames are attached with bolts that provide consistent alignment from frame-to-frame as well as strength and rigidity to the panel run.

Tiles: tackable acoustic and glass

Provide Traxx mounting systems

Sliding privacy doors: do not need a threshold or header and includes door frame with 4 mm resin insert, attachment hardware and matching end trim

Wireway Covers: Steel painted

Acoustical Ratings: NRC rating = .65 STC rating = 15

Power options include: 10-wire shared neutral: 6 hot, 2 neutral, 2 ground and 10-wire independent neutral: 4 hot (2 and 2), 4 neutral, 2 ground Note: Independent and shared neutral components cannot be mixed. (TBD)

All electrical components are nondirectional.

The building’s power capability should be determined before power is configured and components are specified.

Base wireway power harnesses and jumpers distribute power through the base.

Base wireway power entry allows power to enter at the floor, wall, or column. Power can then be distributed to the base and/or jumped up to a technology or power/data. Provide 2 data and 4 power outlets.

The Footprints Worksurfaces and Support line provides components to build workstations as shown on plans including worksurfaces, above storage, filing units, wall and worksurface supports, lighting, tackboards/accessories and all necessary assembly connections.

Worksurface thickness: 1 3/16"

Surface Material: High-pressure laminate (HPL) with cable management grommet

Rims: Vinyl

End support panel: HPL

BBF and FF: Metal, mobile on 4 non-locking casters with one counterweight and lock

Flipper Door Overhead Storage: Painted metal, receding locking doors with LED task light

Fabric covered tack board grade 2

WS-5 L-Shaped Workstation: 6’-0” x 8’-0”

L-Shaped workstation configuration either wall or panel mounted including sliding mobile BBF, overhead storage, task light and fabric tack board length of overhead storage, sliding privacy door. See plans for panel locations and heights.

WS-6 L-Shaped Reception Workstation: 6’-0” x 8’-0”

L-Shaped workstation configuration panel mounted including mobile BBF and FF, and transaction counter. See plans for panel locations and heights.

WS-7 Panel Surround: 8’-0” x 12’-6”

Panel configuration with sliding privacy door only. Interior of the office to have HPL Priority Collection. See plans for

CASEGOODS

KIMBALL / Wood Veneer PRIORITY Collection OFF-1 Configurations vary

Exterior surfaces wood veneer.

Joints are securely fastened with dowels and mechanical fasteners to ensure maximum strength.

Drawer fronts are 3⁄4"-thick, 3-ply construction. Five-sided drawer construction allows easy removal of drawer fronts.

Drawer sides and back are 1⁄2" thick and wrapped in natural woodgrain vinyl. Bottoms are 3⁄16" thick.

Drawer suspensions feature black slides with precision steel ball bearings to ensure long-lasting, quiet, smooth operation. Box, file, and lateral file drawers feature full extension slides.

Black filing rods are standard in all file drawers to accommodate various filing requirements.

Face-mounted locks. Lock cylinders are removable if rekeying is necessary. Key random and key specific options are available.

Fixed modesty panels are featured on all assembled casegoods.

Provide hinged modesty where necessary for wall power access.

Hinged modesty panel swings inward to allow access to wall outlets.

Softened wood edge detail

OFF-1 Wood workstation components - configurations vary see plans:

[A] Left Pedestal Desk 72”w x 36”d x 29”h Box/box/file letter-with locking pedestal

Breakfront half modesty panel

[B] Bridge Return 48”w x 21”d x 29”h (open in back or with hinged modesty panel)

[C] Lateral File Credenza 72”w x 24”d x 29”h 30” File/file lateral file pedestal with lock

[D] Wall-Mount Overhead 72”w x 15.75”d x 19”h 4-door with full-height recessed back panel, finished inset top, center divider, LED task lighting, attachment brackets and rail and 19” high tack boards below.

[E] High Back Overhead Organizer 72”w x 16”d x 38”h 4-door with Unfinished back, one black plastic grommet with cover, finished inset top, center divider, LED task lighting, attachment brackets and rail and 19” high tack boards below.

WAR-1 Wood Storage Wardrobe 36”w x 15.75”d x 67”h

Full length two door storage wardrobe with hanging bar, three adjustable/removable shelves and two fixed shelves, including bottom shelf, locking.

Finish: To be selected wood veneer

BC-1 4-Shelf Wood Bookcase

35 7⁄8"w x 15 3⁄16"d x 53”h 3⁄4"-thick wood shelves

11 7⁄8" shelf openings when shelves are in center position

Finished inset top

Closed back

Finish to be selected.

KIMBALL / HPL Priority Collection

OFF-2

Exterior surfaces HPL

Joints are securely fastened with dowels and mechanical fasteners to ensure maximum strength.

Drawer fronts are 3⁄4"-thick, 3-ply construction. Five-sided drawer construction allows easy removal of drawer fronts.

Drawer sides and back are 1⁄2" thick and wrapped in vinyl. Bottoms are 3⁄16" thick.

Drawer suspensions feature black slides with precision steel ball bearings to ensure long-lasting, quiet, smooth operation. Box, file, and lateral file drawers feature full extension slides.

Black filing rods are standard in all file drawers to accommodate various filing requirements.

Face-mounted locks. Lock cylinders are removable if rekeying is necessary. Key random and key specific options are available.

Fixed modesty panels are featured on all assembled casegoods.

Optional hinged modesty panel is available on assembled bridges, returns, kneespace, and single-pedestal credenzas.

Hinged modesty panel swings inward to allow access to wall outlets. It lifts from the floor and is held in place by leveling feet.

OFF-2 HPL workstation components - configurations vary see plans:

[A] Left Pedestal Desk 72”w x 36”d x 29”h Box/box/file letter-with locking pedestal

Breakfront half modesty panel

[B] Bridge Return varies 54”w x 30”d x 29”h and 42”w x 24”d x 29”h (open in back or with hinged modesty panel)

[C] Return 48”w x 24”d x 29”h with FF locking pedestal (open in back or with hinged modesty panel)

[D] File Credenza 72”w x 24”d x 29”h

[E] U-shaped Worksurface 54”w x 30”d x 29”h Softened edge, end panel (or panel supported) and round metal column support.

[F] Wall-Mount Overhead 72”w x 15.75”d x 19”h 4-door with full-height recessed back panel, finished inset top, center divider, LED task lighting, attachment brackets and rail and 19” high tack boards below.

[G] High Back Overhead Organizer 72”w x 16”d x 38”h 4-door with Unfinished back, one black plastic grommet with cover, finished inset top, center divider, LED task lighting, attachment brackets and rail and 19” high tack boards below.

WAR-2 HPL Storage Wardrobe 36”w x 15.75”d x 67”h

Full length two door storage wardrobe with hanging bar, three adjustable/removable shelves and two fixed shelves, including bottom shelf, locking.

Finish: To be selected HPL

WAR-3 Wood Storage Wardrobe 18”w x 15.75”d x 67”h

Full length one door storage wardrobe with hanging bar, three adjustable/removable shelves and two fixed shelves, including bottom shelf, locking.

Finish: To be selected HPL

BC-1 4-Shelf HPL Bookcase

35 7⁄8"w x 15 3⁄16"d x 53”h 3⁄4"-thick shelves

11 7⁄8" shelf openings when shelves are in center position

Finished inset top

Closed back

Finish to be selected HPL

ACCESSORIES

CLARIDGE / Concept Dry Erase Marker Board

MB-1 White board 12’-0”w x 5/16”d x 4’-0”h

MB-2 White board 6’-0”w x 5/16”d x 4’-0”h

Writing surface is LCS3 Porcelain, a Lifetime Ceramic Surface Narrow aluminum trim profile with eased edge Satin anodized aluminum frame is available in 24 standard colors Projection friendly writing surface that won’t ghost or stain – optimal surface for writing and erasing Concealed hanging system Accepts magnet accessories Provide Magnetic Slim Marker Caddy M-MC2P 9” W, 1-3/8” H, 1-3/8” D

QUARTET / Two-shelf Freestanding Garment Rack

GR Garment Rack Model #20225 3’-0”w x19.8” D x 61”h

Single-sided freestanding garment rack features a top and bottom shelf for double the storage space Powder coated textured steel.

Perforated top shelf provides additional storage Attachable umbrella rack and 12 durable hangers Perforated shelves for garment ventilation.

3" standard hanger spacing.

Adjustable leveling glides.

Top storage shelf, bottom shelf for boots.

Provide 24 additional Quartet hangers (20803)

ULINE / Stainless Steel Wall-Mount Shelf

SHELF Stainless Steel Shelf 36”w x 18”d x 34”h

Withstands harsh environments Reduces dust buildup with open wire design Shelves adjust in 1” increments Includes mounting hardware Type 304 Stainless Steel

USA BUILING SUPPLIES / 60 Slot Mail Shelf with 12” Riser

MAIL 31 1/2"H x 74 3/4"W x 12 1/4"D DM-SR3106

Exterior shell and vertical dividers are constructed of 3/4" 45-50 lb. substrate (particle board) for tabletop mail sorters with thermally fused finish and matching complimentary 3/8" PVC on exposed edges.

Adjustable steel shelves have a 90 degree 1/2" lip label area with center cut out Provide 12” high riser (RSR) Provide shelf label holders javascript:%20display_image();

javascript:%20display_image();

PRODUCT BY LOCATION Section 4

LOCATION FURNITURE TYPE CODE QTY

Break Room 100 Community Table T-3 1

Stools ST-1 3

Conference Room 101 Meeting Table T-1 1

Conference Chairs CH-1 10

Stacking Chairs CH-3 12

Markerboard MB-1 1

Small Table T-5 1

Side Chair CH-4 1

Orderly Room 102 Workstation 3 WS-3 2

Workstation 5 WS-5 4

Workstation 6 WS-6 1

Desk Chair CH-1 7

Storage Cabinet CAB-1 3

Side Chair CH-2 2

Side Table T-6 1

Squadron CMDR 103 Office Casegoods OFF-1 1

Desk Chair CH-1 1

Side Chair CH-2 2

Bookcase BC-1 1

Wardrobe WAR-1 1

Janitor 106 Wall shelf SHELF 1

FAA 112 Workstation 3 WS-3 3

Desk Chair CH-1 4

Storage Cabinet CAB-1 2

Bookcase BC-2 2

Markerboard MB-2 1

Simulation 116 Office Casegoods (L-Shaped) OFF-2 1

Desk Chair CH-1 1

Side Chair CH-4 2

Bookcase BC-2 1

Wardrobe WAR-2 1

Lateral File FC-1 1

Small Table T-5 2

Markerboard MB-2 1

Catco 117 Office Casegoods OFF-1 1

Desk Chair CH-1 1

Side Chair CH-2 2

Bookcase BC-1 1

Wardrobe WAR-1 1

Workstation 7 (Panels Only) WS-7 1

STC Super 118 Office Casegoods (U-shaped Desk) OFF-2 1

Desk Chair CH-1 1

Side Chair CH-2 1

Wardrobe WAR-3 1

ATC Operations 119 Workstation 1 WS-1 4

Workstation 2 (with T-4) WS-2 2

Workstation 4 WS-4 6

Desk Chair CH-1 11

Garment Rack GR 2

Side Chair CH-4 6

Meeting Table T-2 1

Chief of Maint. 121 Office Casegoods OFF-1 1

Desk Chair CH-1 1

Side Chair CH-2 2

Bookcase BC-1 1

Wardrobe WAR-1 1

Maint. Control 122 Office Casegoods OFF-2 1

Desk Chair CH-1 1

Side Chair CH-2 2

Wardrobe WAR-2 1

Maintenance Offices 124 Workstation 1 WS-1 5

Workstation 2 (with T-4) WS-2 2

Workstation 3 WS-3 1

Workstation 4 WS-4 6

Desk Chair CH-1 14

Side Chair CH-4 6

Meeting Table T-2 1

Mobility Warehouse 125A Workstation 1 WS-1 1

Workstation 3 WS-3 1

Wardrobe 2 WAR-2 1

Lateral File FC-1 2

Desk Chair CH-1 2

Maintenance Shop 126 Workstation 1 WS-1 1

Desk Chair CH-1 1

Briefing Room 129 Small Table T-5 1

Side Chair CH-4 1

Lectern LEC 1

Inventory Control 132 Workstation 1 WS-1 2

Workstation 3 WS-3 2

Desk Chair CH-1 4

Sit to Stand Table T-4 1

Side Chair CH-4 1

PRODUCT SUMMARY Section 5

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

Office Chair CH-1 26.25”w x 23”d x 43.25”h High performance task chair with mesh back, upholstered seat, adjustable lumbar and arms Color TBD Kimball Joya 59

Office Side Chair CH-2 21”w x 22.75”d x 33”h Side Chair, mesh back, upholstered seat and arms Color TBD Kimball Joya 9

Stacking Chair CH-3 23.5”w x 21”d x 32”h Stacking Chair with Arms; No Casters; Metal Frame;

Upholstered seat and back Color TBD Kimball Event Stacking Chair 12

CH-4 19.75”w x 21”d x 32”h Stacking Chair w/out Arms; Casters; Metal Frame;

Upholstered seat and back Color TBD Kimball Event Stacking Chair 15

Stool ST-1 18.75”w x 24”d x 30”h Café Stool with Metal Frame and Contoured wood seat Color TBD KI, INC Apply Café Stool/low back 3

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

Conference / Training T-1 120”w x 48”d x 28”h Racetrack w/ Y-Base; Lam. Top and Self-Edge;

Power/date for Wire Mgmt. Colors TBD Kimball Dock Meeting Table 1

T-2 72”w x 36”d x 28”h Racetrack w/ Y-Base; Lam. Top and Self-Edge Colors TBD Kimball Dock Meeting Table 2

Café Table T-3 60”w x 24”d x 42”h Standing Height Community Table; Laminate Top with Self-Edge; Tubular Steel Base Color TBD Falcon 79ST Series 1

Worksurfaces T-4 60”w x 29”d Rectangular Sit-to Stand table with Lam Top; Motor Operated Base Color TBD Kimball Xsede Height Adjust Table 5

T-5 31”w x 22”d Rectangular Table with Formcoat top on Casters;

Height Adjustable Leg Color TBD Herman Miller Resolve Input 4

Side T-6 24” dia. x 21”h Round End Table w/ Palm Top and Metal Base Color TBD National Staccato Side Table 1

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

Lectern LEC 22”w x 22”d x 45”h Lectern Tower; Metal Frame; Laminate Top on Locking Casters Colors TBD KI, INC All Terrain Mobile Lectern 1

SEATING

LECTERN

BASIS OF

DESIGN MODEL / MODEL # QTY

Storage Cabinet CAB-1 36”w x 18”d x 72”h Metal Storage Cabinet with Base, Adjustable Shelves and Lock Color TBD

Herman Miller Meridian Storage Cabinet 5

File Cabinet FC-1 36”w x 18”d x 39”h Metal 4-Draw Lateral Filing Cabinet with Base and Lock Color TBD

Herman Miller Meridian Storage Cabinet 3

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

Workstations WS-1 24"d x Varies Straight Shaped w/ Laminate Surfaces; Overhead Bins; Mobile BBF; Task Light and Tack Board Colors TBD Kimball Interworks EQ/Footprint 12

WS-2 60”w x 24”d Height Adj.

Straight Shaped Adjustable Table Workstation w/ Laminate Surfaces; Overhead Bins; Mobile BBF;

Task Light and Tack Board

Colors TBD Kimball Interworks EQ/Xsede Table 4

WS-3 6'-0" x 6'-0" L-Shaped w/ Laminate Surfaces; Overhead Bins;

Mobile BBF and FF; Task Light and Tack Board Colors TBD Kimball Interworks EQ/Footprint 9

WS-4 8'-0" x 6'-0" L-Shaped w/ Laminate Surfaces; Overhead Bins;

Mobile BBF and FF; Task Light and Tack Board Colors TBD Kimball Interworks EQ/Footprint 12

WS-5 8'-0" x 6'-0" L-Shaped w/ Laminate Surfaces; Overhead Bins;

Mobile BBF; Wardrobe; Sliding Privacy Door; Task Light and Tack Board

Colors TBD Kimball Interworks EQ/Footprint 4

WS-6 8'-0" x 6'-0" L-Shaped w/ Laminate Surfaces; Mobile BBF and FF; Transaction Counter Colors TBD Kimball Narrate/Footprint 1

WS-7 8'-0" x 12'-6" Power/data Panel Surround Only; Interior Office Casegoods Under OFF-2 Colors TBD Kimball Narrate/Priority Collection 1

STORAGE & FILING

OPEN WORKSTATIONS

BASIS OF

DESIGN MODEL / MODEL # QTY

Wood Casegoods OFF-1 See Product Spec

Wood Office Suite Consisting of Pedestal Desk, Bridge return, Lateral File Credenza, Overhead, Wardrobe and Bookcase. Configurations Vary - See Plan

Colors TBD Kimball Priority Wood Veneer 3

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

HPL Casegoods OFF-2 See Product Spec

HPL Office Suite Consisting of Pedestal Desk or U- Shaped Worksurface, Bridge return, Lateral File Credenza, Overhead, Wardrobe and Bookcase.

Configurations Vary - See Plan

Colors TBD Kimball Priority HPL 3

CODE SIZE DESCRIPTION COLOR /

FINISH

BASIS OF

DESIGN MODEL / MODEL # QTY

Marker Boards MB-1 12’-0”w x 5/16”d x 4’-0”h Magnetic, Porcelain Ceramic Surface with Narrow aluminum trim profile and Magnetic Marker Caddy Colors TBD Claridge Concept Dry Erase 1

MB-2 6’-0”w x 5/16”d x 4’-0”h Magnetic, Porcelain Ceramic Surface with Narrow aluminum trim profile and Magnetic Marker Caddy Colors TBD Claridge Concept Dry Erase 2

Garment Rack GR 3’-0”w x19.8” D x 61”h Powder Coated Steel, One-sided Garment Rack with Shelve, Umbrella Storage and Add 'l Hangers Black Quartet Model #20225 2

Wall Shelf SHELF 36”w x 18”d x 34”h 304 Stainless Steel Wire Shelving Unit; Two Adjustable Shelves; Mounting Hardware Stainless ULINE Model #H-4795 1

Mail Sorter MAIL 31.5"H x 74.75"W x 12.25"D Adjustable 60 Slot Mail sorter with 12" Riser Colors TBD USA Building Suppies Model #DM-SR3106 1

CASEGOODS (OFFICES 116, 118 and 122 )

ACCESSORIES

CASEGOODS (OFFICES 103, 117 and 121 )

FLOOR PLANS/DRAWINGS Section 6

PA

N

EL

S

YS

TE

M W

IL

L

N

EE

D

PO

W

ER

P O

LE

T

O P

RO

VI

DE

D

AT

A

AN

D

PO

W

ER

T

O W

O

RK

ST

AT

IO

N

S

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Typewritten Text

72" H FABRIC PANEL WITH 12" GLASS FRAME PANEL ABOVE

Sarah Line

Sarah Typewritten Text

42" H FABRIC PANEL WITH TRANSACTION TOP

Sarah Line

Sarah Typewritten Text

42"H FABRIC PANEL WITH 12" GLASS PANEL ABOVE

Sarah Typewritten Text

48" H FABRIC PANEL WITH 12" GLASS FRAME PANEL ABOVE

Sarah Typewritten Text

Sarah Typewritten Text

Sarah Line

Sarah

48" H FABRIC PANEL WITH 12" H GLASS FRAME PANEL ABOVE

Sarah Line

Sarah Line

Sarah Line

Sarah Typewritten Text

72" H FABRIC PANEL WITH 12" GLASS

FRAME PANEL ABOVE

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Line

Sarah Typewritten Text

48" H FABRIC PANEL WITH 12" GLASS FRAME PANEL

ABOVE

Sarah Typewritten Text

80" H FABRIC PANEL

Sarah Line

Sarah Typewritten Text

67" H FABRIC PANEL

Sarah Line

Sarah Typewritten Text

42" H FABRIC PANEL

Sarah Typewritten Text

Sarah Typewritten Text

Sarah Typewritten Text

Sarah Typewritten Text

Sarah Typewritten Text

Sarah

PANEL SYSTEM WILL NEED POWER POLE OR WHIP TO PROVIDE DATA AND POWER TO WORKSTATIONS

View of Orderly Room 102

View of Maintenance Offices 124

231 Main Street, Biddeford, ME 04005 TEL 207.283.0193 FAX 207.283.4283 www.oakpoint.com