Exhibit_C_CDRL_Abrams_EDTT_3-May-16.pdf

ANNEX TO EXHIBIT - C

DATA ITEM NUMBERS:

C001 LOGISTICS PRODUCT DATA

C002 LOGISTICS PRODUCT DATA SUMMARIES

LOGISTICS PRODUCT DATA

(LPD)

SAE GEIA-STD-0007 /SAE GEIA-HB-0007 – DI-SESS-81758A

Tailored Logistics Product Data Attribute Selection Sheet & Guidance

SAE GEIA-STD-0007/ SAE GEIA-HB-0007 – DI-SESS-81759A

Tailored Logistics Product Data Summary & Guidance

FOR

M1A2 SEPV2 Abrams Tank Engine Diagnostic and Troubleshooting Trainer

(ED/TT)

Prepared by

U.S. ARMY Program Executive Office for Simulation, Training, & Instrumentation (PEO STRI)

12350 Research Parkway Orlando, Florida 32826-3276

Annex to Exhibit C CDRLs – C001 LPD and C002 LPD Summaries

SAE GEIA-STD-0007/ SAE GEIA-HB-0007

* DATA PRODUCT DELIVERABLE: LPD Attribute Selection Worksheet/LPD Summaries

* This worksheet is used to select data deemed necessary by the government. *

* Data should be used to feed downstream government process. *

* SELECT EXPLANATION *

* X Data product required on all items *

* A As applicable *

* R Repairables only *

* P All “P” source code items *

* N New “P” source code items *

* Y National Stock Number items *

* O “Ref” items only *

* F First appearance items only *

* C COTS items *

* I NDI items *

* D Developmental items *

* L LRU/WRA items *

* S SRA/SRU items *

* M Packaging, Common items *

* B Packaging, Bulk items *

* E Support Equipment *

* NOTE: Other codes may be assigned by the program office as identified below. *

* Program specific selections and explanations. *

* ISL INITIAL SPARES/REPAIR PARTS LIST *

* CBL COMMON AND BULK ITEM LIST *

* TTE TOOLS AND TEST EQUIPMENT LIST *

* PPL PROVISIONING PARTS LIST *

* MCL MATERIEL COMPONENT LIST (PEO STRI UNIQUE) *

* MANP MASS CREATE PROCESS LIST (PEO STRI UNIQUE) *

* LPDS LOGISTICS PRODUCT DATA STORE LIST (PEO STRI UNIQUE) *

* Ref SAE GEIA-STD-0007 / SAE GEIA-HB-0007 for code definitions *

DATA PRODUCT TITLE SELECT ADDITIONAL INFORMATION

allowance_item_code X PPL; LPDS allowance_item_quantity X PPL; LPDS automatic_data_processing_equipment_code hm_Item_Basis_of_Issue_data authorized_quantity end_item_range organizational_level calibration_measurement_requirement_summary_ recommended calibration_interval A TADSS as required, TTE (Engineering estimate acceptable) calibration_item calibration_procedure A TADSS as required, TTE calibration_required A TADSS as required, TTE calibration_time change_authority_number cleaning_and_drying_procedures commercial_and_government_entity_code X CBL; ISL; PPL; TTE; MCL; MANP; LPDS (See pg 10, LPD Additional Guidance) adapter_interconnector_device_required additional_reference_number_commercial_and_ government_entity_code item_commercial_and_government_entity_code automatic_test_equipment_commercial_and_ support_equipment_commercial_and_government_ entity_code contractor_technical_information_code_commercial_ and_government_entity_code packaging_data_preparer_commercial_and_ government_entity support_equipment_commercial_and_ operational_test_program_ commercial_and_ contractor_furnished_equipment_government_ furnished_equipment design_data_category_code_contractor_ recommended integrated_logistics_support_equirement_ category_code_contractor_recommended contractor_technical_information_code physical_security_pilferage_code criticality_code cushioning_and_dunnage_material cushioning_thickness demilitarization_code X PPL design_data_category_code design_data_price end_item_acronym_code X PPL; LPDS (See pg 10, LPD Additional Guidance for value to enter) essentiality_code X ISL; PPL design_data_category_code_estimated_price design_data_category_code_government_required integrated_logistics_support_requirement_ category_code_estimated_price figure_number nonoperational_fragility_factor Non-Operability Fragility Factor (NOFF) technical_manual_functional_group_code hardness_critical_item Hardness Critical Item (HCI) (Nuclear) hardware_development_price hazardous_code X ISL; PPL indenture_code X Indenture Code (IND CD)/Indenture

Code for Kits PPL; CBL; MCL logistics_support_analysis_control_number_

X PPL; ISL

input_power_source_ac_dc Input Power Source: Alternating Current/Direct Current input_power_source_operating_ range_minimum input_power_source_operating_ range_maximum input_power_source_ frequency_range_minimum input_power_source_ frequency_range_maximum input_power_source_phase input_power_source_watts input_power_source_percent _maximum_ripple integrated_logistics_support_price integrated_logistics_support_ Integrated Logistic Support (ILS) requirement_category_code Requirement Category Code (IRCC) interchangeability_code intermediate_container_code intermediate_container_quantity item_category_code system_end_item_item_designator_code end_article_item_designator item_name X CBL; ISL; PPL; TTE; MCL;MANP; LPDS support_equipment_full_item_name item_name_code item_number special_packaging_instruction_number_ julian_date line_replaceable_unit price_lot_quantity_to price_lot_quantity_from maintenance_action_code maintenance_replacement_rate_i Maintenance Replacement Rate (MRR) I/Failure Factor 1 (FF1) maintenance_replacement_rate_ii Maintenance Replacement Rate (MRR) II/Failure Factor 2 (FF2) condemned_at_depot_maintenance_task_ distribution

Maintenance Task Distribution (MTD) at Condemnation At Depot (CAD) material_leadtime material_weight maximum_allowable_operating_time required_operational_mean_time_between_failures X ISL; PPL support_equipment_mean_time_between_failures required_operational_mean_time_to_repair support_equipment_mean_time_to_repair annual_operating_requirement_measurement_base mean_time_between_failure_operational_ measurement_base wearout_life_measurement_base method_of_preservation_code mobile_facility_code container_national_stock_number interoperable_item_national_item_identification_ number national_stock_number_cognizance_code national_stock_number_materiel_control_code line_item_number X PPL; MCL national_stock_number_federal_supply_ classification X PPL; MCL; LPDS

(Management Control Numbers Acceptable) national_stock_number_national_item_ identification_number X PPL; MCL; LPDS

(Management Control Numbers Acceptable) national_stock_number_special_materiel_ identification_code_materiel_management_ aggregation_code national_stock_number_activity_code next_higher_assembly_provisioning_list_ item_sequence_number next_higher_assembly_provisioning_list_ item_sequence_number_indicator not_repairable_this_station operators_manual optional_procedures_indicator overhaul_replacement_rate packaging_category_code support_equipment_parameter_input_or_ output_code support_equipment_parameter support_equipment_parameter_range_from support_equipment_parameter_range_to support_equipment_parameter_accuracy support_equipment_parameter_range_or_ value_code unit_under_test_parameter_input_output_code unit_under_test_parameter unit_under_test_parameter_range_from unit_under_test_parameter_range_to unit_under_test_parameter_accuracy unit_under_test_parameter_range_value_code unit_under_test_parameter_operational_ specification_code pass_thru_price precious_metal_indicator_code X PPL preparing_activity preservation_material_code prior_item_provisioning_list_item_ sequence_number production_lead_time program_parts_selection_list prorated_exhibit_line_item_number prorated_quantity system_end_item_provisioning_contract_ control_number X PPL; LPDS (See pg 10, LPD Additional Guidance for provisioning_list_category_code prior_item_provisioning_list_item_sequence_ parts_manual_provisioning_nomenclature X PPL; LPDS (See pg 10, LPD Additional Guidance for price_used provisioning_remarks system_end_item_quantity_per_assembly X ISL; PPL; MCL system_end_item_quantity_per_end_item X ISL; PPL; MCL quantity_per_figure system_equipment_quantity_per_test quantity_per_unit_pack quantity_procured quantity_shipped recommended_minimum_system_stock_level recurring_cost reference_designation reference_designation_code reference_number X CBL; ISL; PPL; TTE; MCL; MANP; LPDS adapter_interconnector_device_reference_ additional_reference_number_item_reference_ number X CBL; ISL; PPL; TTE;

automatic_test_equipment_reference_number support_equipment_unit_under_test_ reference_number support_equipment_reference_number additional_reference_number additional_reference_number_reference_ number_category_code additional_reference_number_reference_ number_variation_code reference_number_variation_code contractor_repair_cycle_time organizational_repair_cycle_time depot_shipyard_repair_cycle_ time special_repair_activity_repair_cycle_time replaced_or_superseding_provisioning_ list_item_sequence_number replaced_or_superseding_provisioning_ list_item_equence_number_Indicator organizational_replacement_task_distribution special_repair_activity_replacement_task_ distribution support_equipment_recommendation_data_ date_of_revision_submission overhaul_replacement_rate same_as_provisioning_list_item_sequence_ design_data_category_code_scope from_serial_number_effectivity to_serial_number_effectivity service_designator_code support_equipment_service_designator using_service_designator_code shelf_life X PPL shelf_life_action_code skill_specialty_code_for_support_equipment_ operator source_maintenance_and_recoverability_code X PPL; CBL; ISL; TTE support_equipment_source_maintenance_ recoverability_code spares_acquisition_integrated_with_production special_maintenance_item_code special_marking_code special_material_content_code special_packaging_instruction_number special_packaging_instruction_number_ revision supplemental_packaging_data support_equipment_shipping_length support_equipment_shipping_width support_equipment_shipping_height support_equipment_explanation_narrative support_equipment_recommendation_ data_number support_equipment_recommendation_data_ revision_remarks support_equipment_shipping_weight technical_manual_change_number technical_manual_code X PPL; LPDS (See pg 10, LPD Additional Guidance for tecnhical_manual_number X PPL; LPDS (See pg 10, LPD Additional Guidance for unit_under_test_parameter_test_accuracy_ ratio_actual arameter_test_accuracy_ratio_desired parameter total_item_changes total_quantity_recommended X ISL (see attached for additional guidance) type_equipment_code type_of_change_code price_type_of_price_code unit_container_code unit_container_level unit_of_issue X CBL; ISL; PPL; LPDS unit_of_issue_conversion_factor unit_price. X CBL; ISL; PPL; MCL; TTE; MANP unit_of_measure X CBL; ISL; PPL support_equipment_shipping_dimensions_ unit_of_measure maximum_unit_pack_cube unit_size_length unit_size_width unit_size_height maximum_unit_pack_length maximum_unit_pack_width maximum_unit_pack_depth unit_under_test_explanation unit_weight maximum_unit_pack_weight usable_on_code X PPL; LPDS (See pg 10, LPD Additional Guidance for wearout_life work_unit_code

UNIQUE DATA ELEMENTS

The Maintenance Plan Products have additional attributes that are calculated from the attributes in GEIA-

STD-0007. These attributes and their respective calculations are provided below and should be included in contractual documents.

Rotable Pool Factor (RPF): The predicted number of times in one maintenance cycle that an item is removed from its next higher assembly at the Organizational/Intermediate level of maintenance, repaired at the Intermediate level and returned, ready for issue at this level (9 character numeric field with a 3-character decimal place).

RPF = [MTD(F) + MTD(H)] X MRR

MTD(F) – intermediate_direct_support_ maintenance_task_distribution

MTD(H) – intermediate_general_support_ maintenance_task_distribution

MRR – maintenance_replacement_rate_item warranty_ data X PPL; ISL (See Guidance Below) approved_baseline_drawing_revision X PPL (See Guidance Below) Serial_Number

A

MCL; Required for COTS IT Components

(computers, switches, servers, routers) non-expendable components and any serially managed items

Accounting Requirements Code (ARC):

Nonexpendable-N

Durable-D

Expendable-X

X

PPL; MCL; MANP

Per AR 350-38: TADSS that are not consumed in use and—

(1) Cost $1,000 or more are nonexpendable.

(2) Cost between $200 to $999.99 are durable.

(3) TADSS that are consumed in use, lose their identity, or cost less than $200 are expendable.

IT components (Switches, Routers, Computers, Servers) are considered nonexpendable, as they do not lose their identity when installed.

Unique Item Identifier MCL: Required for all items that are labeled with an IUID. See MIL STD 130N

LOGISTICS PRODUCT DATA (LPD) ADDITIONAL GUIDANCE

CAGE CODE/REFERENCE NUMBER - All known definitive references shall be provided. The CAGE and reference number of the OEM of the part will be used as the primary reference unless a government specification, standard, or drawing is applicable. Alternate CAGE and reference number is required for all known sources.

INTEROPERABLE ITEM NAME - Approved interoperable item names in accordance with the Federal Item Name Directory (H6) are not required. Common names used commercially or by the OEM are acceptable if they are in English and representative of the item. Brand specific names should be avoided as well as ‘catch’ names that are not intuitively representative of the item or its function. Item Names cannot be abbreviated unless approved by the requiring authority.

MEAN TIME BETWEEN FAILURES - Engineering estimates are acceptable when OEM cannot supply data for commercial items.

SOURCE, MAINTENANCE AND RECOVERABILITY (SMR) CODE - The contractor shall use AR 700-82 as guidance. The Maintenance and Recoverability codes used should represent the level of responsibility rather than the source of responsibility. An LCCS contractor, for example, may provide Organization, Intermediate, and Depot level support; therefore Maintenance codes O, F, G and D could all be used to indicate support provided by a LCCS contractor. Code “K” for contractor facility support should be limited to those items that must be serviced by an OEM or OEM authorized provider.

The following guidance was provided by DA Policy Memo in 2006 for use in assigning SMR codes applicable to a two level maintenance strategy:

Level 1 - Field Maintenance

(C) Operator/Crew

(O) Services or Aviation Maintenance Company (AMC) tasks

(F) Field maintenance or Aviation Support Battalion (ASB) tasks

Level 2 - Sustainment Maintenance

(H) Below Depot sustainment

(L) Special Repair

(K) Contractor

(D) Depot Maintenance

TOTAL QUANTITY RECOMMENDED - The data provided should represent the number of items the contractor has calculated to be necessary to support the newly fielded end item until normal supply and maintenance procedures can assume support. This calculation should include consideration for the essentiality of the component, price, lead times, and failure factors. Separate quantities may be required to support differing numbers of end items at multiple locations.

WARRANTY DATA - The contractor shall provide all the warranty information associated to all procured items. The warranty product data shall include manufacturer’s point of contact, CAGE codes, length of warranty, and special warranty provisions, e.g., third party vendor access.

APPROVED BASELINE DRAWING REVISION – Drawing revisions of each component shall be documented based on the results of a Government approved Configuration Audit (CA) FCA/PCA.

END ITEM ACRONYM CODE – Enter code: PEOSTRI SYSTEM END ITEM PROVISIONING CONTRACT CONTROL NUMBER – Enter code: W6ECAA PARTS MANUAL PROVISIONING NOMENCLATURE – Enter code: PEO STRI assigned training system nomenclature TECHNICAL MANUAL CODE – Enter code: TNR (trainer) TECHNICAL MANUAL NUMBER – Enter PEO STRI assigned Operators User Manual number USABLE ON CODE – Enter code: TRNR

LOGISTICS PRODUCT DATA SUMMARIES GUIDANCE

Reference: DI-SESS-81759A, Logistics Product Data Summaries. The desired information per summary and associated guidance is developed specifically for the Attribute Selection Sheet Appendix A, tailored from the SAE GEIA-HB-0007.

APPLICABILITY

The following Logistics Product Data Summaries model templates provide information required for the contractor to conduct logistics planning and analysis, influence program decisions, assess design, and verify contractor performance. To avoid redundancies and inconsistencies, the requirements for these summaries shall be verify against other program functional elements data requirements.

It is not intended that all the requirements contained in this model summaries shall be applied. These summaries are tailored to the minimum requirements of the applicable contract for the acquisition of TADSS, assemblies, and components.

SUMMARY TITLE: Post Production Support

SPECIFIC INSTRUCTIONS:

Reference: DI-SESS-81759A, Logistics Product Data Summaries developed specifically IAW Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

Provide overall average annual support cost estimates in current year dollars per site for:

a) Hardware Maintenance (labor)

b) Routine replacement of parts (hardware)

c) Software support, including recurring licensing

Provide life expectancy and refresh recommendations (in years) for all major subsystems and components. (e.g. routine refresh of computer equipment)

Provide recommendations for when major modification or upgrades may be required (year, component or subsystem, estimated cost).

Estimate requirements for manpower and personnel for annual operations, support, and maintenance.

Identify any supportability risk items due to limited sources, long lead times, support limitations, or other concerns and suggest support alternatives to overcome them.

DATA IN LOGISTICS PRODUCT DATA SPECIFICATION (Please Provide the data product title):

DATA NOT IN LOGISTICS PRODUCT DATA SPECIFICATION (Please provide the product data title, its definition and its format):

Summary shall be in narrative format with embedded tables as required. Data elements are not limited to those indicated above.

SUMMARY LAYOUT (if applicable): Government Provided [ ] Contractor Provided [X]

SUMMARY TITLE: Repair Analysis

Reference: DI-SESS-81759A, Logistics Product Data Summaries, developed specifically for the Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

These summaries provide the government with conclusions and recommendations of the maintenance repair analysis. The government may verify the conclusions and recommendations by utilizing contractor’s inputs to perform an in-house analysis. These summaries may also be used by the government to develop initial fielding plans for the end item’s support structure. The conclusions may include actions and recommendations for influencing the system design; a listing of which items should be repaired and which should be discarded. These summaries may identify for each item being repaired the level of maintenance at which the repair should be performed and associated costs. These summaries may identify for the system support structure, the operational readiness achieved, and the placement and allocation of spares, support equipment, and personnel.

These summaries may also include other information for the analysis performed, e.g., a listing of the input data and their corresponding values and sources of the data; operational scenario modeled;

assumptions made; constraints and noneconomic factors imposed on the system; maintenance alternatives considered; the analytical method and model used to perform the economic evaluations;

and discussion of the sensitivity evaluations performed and results obtained.

SUMMARY LAYOUT (if applicable): Government Provided [ ] Contractor Provided [ ]

SUMMARY TITLE: Maintenance Planning

Reference: DI-SESS-81759A, Logistics Product Data Summaries, developed specifically for the Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

These summaries provide maintenance planning information to the government that may be used to develop initial fielding plans for the end items support structure. These summaries may also be used to verify that the maintenance actions and support structure are aligned with the government’s requirements and maintenance concept. The information contained within these summaries is associated with repairable items to the level of detail specified on contract. The repairable items should be identified within the hierarchy of the end item broken down by an agreed upon configuration control method. It should identify all preventive and corrective maintenance actions along with the required spares and support equipment. These summaries should also provide supporting information justifying the need for each maintenance action, e.g., elapsed time of maintenance actions; task frequency; failure rate of an item; Mean Time To Repair an item; and an in some cases item’s man-hour allocation by maintenance action and level.

See Paragraph 4.1.2 in SAE GEIA-HB-0007.

DATA NOT IN LOGISTICS PRODUCT DATA SPECIFICATION (Please provide the data product title, its definition and its format): Summary shall be in narrative format with embedded tables as required.

Data elements are not limited to those indicated above.

SUMMARY TITLE: Support and Test Equipment

Reference: DI-SESS-81759A, Logistics Product Data Summaries, developed specifically for the Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

These summaries provide data necessary to register, or verify the registry of, the support or test equipment in the government’s inventory. They provide details of the Test Measurement and Diagnostic Equipment (TMDE) calibration procedures, technical parameters, and any piece of support equipment needed to support the system.

See Paragraph 4.1.3 of SAE GEIA-HB-0007.

its definition and its format): Summary shall be in narrative format with embedded tables as required.

SUMMARY TITLE: Supply Support

Reference: DI-SESS-81759A, Logistics Product Data Summaries, developed specifically for the Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

These summaries provide the government with information on static and application related hardware information which may be used to determine initial requirements and cataloging of support items to be procured through the provisioning process. These summaries may include the identification of the system breakdown, maintenance replacement factors, roll-up quantities, design change information, and associated technical manuals, as applicable. These summaries may show information on different categories of provisional items such as long lead items, bulk items, tools and test equipment, etc.

See Paragraph 4.1.4 of SAE GEIA-HB-0007.

its definition and its format): Summary shall be in narrative format with embedded tables as required.

SUMMARY TITLE: Manpower, Personnel and Training

Reference: DI-SESS-81759A, Logistics Product Data Summaries, developed specifically for the Attribute Selection Sheet (Appendix A, SAE GEIA-HB-0007).

These summaries provide information to the government so it can establish training plans and ensure manpower and personnel constraints are met. The information contained within this report should identify items’ corrective and preventive maintenance tasks, operations tasks, manpower estimates for each task by maintenance level, personnel skills required to perform the maintenance tasks, and any training required to allow these tasks to be performed. The information contained within this area is associated with items to the level of detail specified on contract. The items should be identified within the hierarchy of the end item broken down by an agreed upon configuration control method.

See Paragraph 4.1.5 of SAE GEIA-HB-0007.

its definition and its format): Summary shall be in narrative format with embedded tables as required.

SUMMARY TITLE: Facilities Summary

Reference GEIA-STD-0007A, Logistics Product Data SAE GEIA-HB-0007, Logistics Product Data Handbook

These summaries identify the facilities required to maintain, operate, train, and test an item. The facilities may be organizational, intermediate, or depot maintenance, training, mobile and test facilities. The summary information contained within shall help plan for any modification to an existing facility or development of a new facility. The information shall be associated with repairable items to the level of detail specified in the contract. The repairable items should be identified within the hierarchy of the end item broken down by an agreed upon configuration control method. Data provided must be in compliance with all Department of Defense and national health, life, and environmental codes. National standards and terminology used by the construction industry for civil, electrical, mechanical, etc., specialties should be used.

See Paragraph 4.1.6 of SAE GEIA Handbook.

DATA IN LOGISTICS PRODUCT DATA SPECIFICATION (Please Provide the product data title):

its definition and its format):

Summary shall be in narrative format with embedded tables as required. Data elements are not limited to those indicated above.

SUMMARY LAYOUT (if applicable): Government Provided [ ] Contractor Provided [X]

ANNEX TO EXHIBIT - C

DATA ITEM NUMBERS:

C003 PAGE-BASED TECHNICAL MANUAL - OPERATOR USER’S

MANUAL

C004 PAGE-BASED TECHNICAL MANUAL - SYSTEM MAINTENANCE

MANUAL

PAGE-BASED TECHNICAL MANUALS

MIL-STD 40051-2C

DEPARTMENT OF DEFENSE STANDARD PARCTICE PREPARATION OF DIGITAL

TECHNICAL INFORMAITON FOR PAGE-BASED TECHNICAL MANUALS

FOR

M1A2 SEPV2 Abrams Tank ED/TT

Prepared by

U.S. ARMY Program Executive Office of Simulation, Training, & Instrumentation (PEO STRI)

12350 Research Parkway Orlando, Florida 32826-3276

MIL-STD 40051-2C Requirement Matrix for Page Based TMs

TABLE A-II. Operators and combined operator/maintenance requirements matrix for

TM Content -10

MIL-STD-40051-

2C

Reference Element Name

FRONT MATTER R

5.2.1 <paper.frnt>

Front cover R

5.2.1.1 <frntcover>

(MC) Promulgation letter 5.2.1.3 <promulgation>

Warning summary R 5.2.1.4 <warnsum>

Change transmittal page 5.2.1.5 <chgsheet>

List of effective pages/work packages

R

5.2.1.6 <loepwp>

Title page R

5.2.1.7 <titleblk>

Table of contents R

5.2.1.9 <contents>

How to use this manual R

5.2.1.10 <howtouse>

CHAPTER 1.

GENERAL INFORMATION,

EQUIPMENT DESCRIPTION,

AND THEORY OF OPERATION

APPENDIX B <gim>

GENERAL INFORMATION

WORK PACKAGE

B.5.2 <ginfowp>

Scope R

B.5.2.3 <scope>

Maintenance forms, records, and reports

B.5.2.4 <mfrr>

Reporting Equipment Improvement Recommendations (EIR)

B.5.2.5 <eir>

Hand Receipt (HR) manuals B.5.2.6 <handreceipt>

Corrosion Prevention and Control (CPC)

B.5.2.7 <cpcdata>

Ozone Depleting Substances

(ODS)

B.5.2.8 <odsdata>

Destruction of Army materiel to prevent enemy use

B.5.2.9 <destructmat>

Preparation for storage or shipment

B.5.2.10 <pssref>

Warranty information B.5.2.11 <wrntyref>

Nomenclature cross-reference list

B.5.2.12 <nomenreflist>

List of abbreviations/acronyms R

B.5.2.13 <loa>

Quality of material P

B.5.2.15 <qual.mat.info>

Safety, care, and handling B.5.2.16 <sftyinfo>

Nuclear hardness B.5.2.17 <hcp>

Calibration B.5.2.18 <calref>

Item unique identification

(IUID)

B.5.2.19 <iuid>

Supporting information for repair parts, special tools, TMDE, and support equipment

P B.5.2.26 <supdata>

Copyright credit line B.5.2.27 <copyrt>

EQUIPMENT DESCRIPTION

AND DATA WORK PACKAGE

B.5.3 <descwp>

Equipment characteristics, capabilities, and features

B.5.3.3 <eqpinfo>

Location and description of major components

B.5.3.4 <locdesc>

Differences between models B.5.3.5 <eqpdiff>

Equipment data R

B.5.3.6 <eqpdata>

THEORY OF OPERATION

B.5.4 <thrywp>

CHAPTER X.

OPERATOR INSTRUCTIONS

APPENDIX C <opim>

DESCRIPTION AND USE OF

OPERATOR CONTROLS AND

INDICATORS WORK PACKAGE

C.5.2.2.1 <ctrlindwp>

OPERATION UNDER USUAL

CONDITIONS WORK PACKAGE

C.5.2.2.2 <opusualwp>

Operation under usual conditions task

C.5.2.2.2.3 <opertsk>

Security measures for electronic data

C.5.2.2.2.4 <secref>

Siting requirements C.5.2.2.2.5 <site>

Shelter requirements C.5.2.2.2.6 <shelter>

Assembly and preparation for use

C.5.2.2.2.7 <prepforuse>

Initial adjustments, before use and self-test

C.5.2.2.2.8 <initial>

Operating procedures R

C.5.2.2.2.9 <oper>

Operating auxiliary equipment C.5.2.2.2.11 <operaux>

Preparation for movement C.5.2.2.2.12 <prepmove>

Decals and instruction plates C.5.2.2.2.13 <instructplt>

OPERATION UNDER UNUSUAL

CONDITIONS WORK PACKAGE

C.5.2.2.3 <opunuwp>

Security measures for electronic data

C.5.2.2.3.4 <secref>

Unusual environment/weather R

C.5.2.2.3.5 <unusualenv>

Fording and swimming C.5.2.2.3.6 <fording>

Interim Chemical, Biological, Radiological, and Nuclear (CBRN) decontamination procedures

C.5.2.2.3.7 <decon>

Jamming and Electronic Countermeasures (ECM)

C.5.2.2.3.8 <ecm>

Degraded operation

C.5.2.2.3.9 <degraded>

Decals and instruction plates C.5.2.2.3.10 <instructplt>

EMERGENCY WORK PACKAGE C.5.2.2.4 <emergencywp>

STOWAGE AND DECAL/DATA

PLATE GUIDE WORK PACKAGE

C.5.2.2.5 <stowagewp>

ON-VEHICLE EQUIPMENT

LOADING PLAN WORK

PACKAGE

C.5.2.2.6 <eqploadwp>

TROUBLESHOOTING

MASTER INDEX

APPENDIX D

D.5.4.4

<tim> <masterindexcategory>

TROUBLESHOOTING INDEX

D.5.5.5 <tsindxwp>

PROCEDURES

NOTE

The notation (*) indicates that at least one of the these content items shall be included

D.5.4.2

<troublecategory>

INTRODUCTION WORK

D.5.5.3 <tsintrowp>

TROUBLESHOOTING INDEX

*OPERATIONAL CHECKOUT

WORK PACKAGES

D.5.5.8.3 <opcheckwp>

*TROUBLESHOOTING WORK

PACKAGES

D.5.5.8.4 <tswp>

*COMBINED OPERATIONAL

CHECKOUT AND

TROUBLESHOOTING WORK

D.5.5.8.5 <opcheck-tswp>

PMCS

MAINTENANCE

INSTRUCTIONS

PMCS may be in its own chapter or may be combined with other maintenance work packages in a maintenance chapter but not both places.

APPENDIX E

E.5.2.1

<mim> <pmcscategory>

PMCS INTRODUCTION WORK

E.5.3.4.1 <pmcsintrowp>

PMCS, INCLUDING

LUBRICATION

INSTRUCTIONS, WORK

E.5.3.4.2 <pmcswp>

PMCS is required as a minimum in one maintenance chapter. PMCS may be in its own chapter or may be combned with other maintenance work packages in a maintenance chapter but not both places.

E.5.2.2 E.5.2.3

<maintenancepmcscategory> <maintenancecategory>

SERVICE UPON RECEIPT

(MAINTAINER LEVEL ONLY)

P

E.5.3.2 <surwp>

Service upon receipt tasks P

E.5.3.2.3 <surtsk>

Siting P E.5.3.2.3.1 <siting>

Shelter requirements P E.5.3.2.3.2 <shltr>

Service upon receipt of materiel

E.5.3.2.3.3 <surmat>

Installation instructions P

E.5.3.2.3.4 <install>

Preliminary servicing of

P E.5.3.2.3.5 <preserv>

Preliminary checks and adjustment of equipment

P E.5.3.2.3.6 <prechkadj>

Preliminary calibration of

P E.5.3.2.3.7 <precal>

Circuit alignment P E.5.3.2.3.8 <calign>

Ammunition markings P E.5.3.2.3.9.1 <mark>

Classification of defects P E.5.3.2.3.9.2 <ammo.defect>

Ammunition handling P E.5.3.2.3.9.3 <ammo.handling>

Procedures to activate ammunition

P E.5.3.2.3.9.4 <arm>

Additional maintenance task P E.5.3.2.3.10 <other.surtsk>

Follow-on maintenance P E.5.3.2.3.11 <followon.maintsk>

EQUIPMENT/USER FITTING

INSTRUCTIONS WORK

E.5.3.3 <perseqpwp>

PMCS INTRODUCTION WORK

R E.5.3.4.1 <pmcsintrowp>

PMCS WORK PACKAGE R E.5.3.4.2 <pmcswp>

MAINTENANCE WORK

E.5.3.5 <maintwp>

Maintenance tasks

E.5.3.5.3 <maintsk> Inspect E.5.3.5.3.2 <inspect> Test E.5.3.5.3.3 <test> Service E.5.3.5.3.4 <service> Adjust E.5.3.5.3.5 <adjust> Align E.5.3.5.3.6 <align> Calibrate E.5.3.5.3.7 <calibration> Remove E.5.3.5.3.8 <remove> Install E.5.3.5.3.9 <install> Replace E.5.3.5.3.10 <replace> Repair E.5.3.5.3.11 <repair> Paint E.5.3.5.3.12 <paint> Overhaul P E.5.3.5.3.13 <overhaul> Rebuild P E.5.3.5.3.14 <rebuild> Lubricate E.5.3.5.3.15 <lube> Mark E.5.3.5.3.16 <mark> Pack E.5.3.5.3.17 <pack> Unpack E.5.3.5.3.18 <unpack>

Preserve E.5.3.5.3.19 <preserv> Prepare for use E.5.3.5.3.20 <prepforuse> Assemble E.5.3.5.3.21 <assem> Disassemble E.5.3.5.3.22 <disassem> Clean E.5.3.5.3.23 <clean> Nondestructive inspection E.5.3.5.3.24 <ndi> Radio interference suppression E.5.3.5.3.25 <ris> Place in service E.5.3.5.3.26 <pis> Towing E.5.3.5.3.27 <tow> Jacking E.5.3.5.3.28 <jack> Parking E.5.3.5.3.29 <park> Mooring E.5.3.5.3.30 <moor> Covering E.5.3.5.3.31 <cover> Hoisting E.5.3.5.3.32 <hoist> Sling loading E.5.3.5.3.33 <sling> External power E.5.3.5.3.34 <extpwr> Preparation for shipment and storage

E.5.3.5.3.35 <pss>

Arm E.5.3.5.3.36 <arm> Load E.5.3.5.3.37 <load> Unload E.5.3.5.3.38 <unload> Software maintenance E.5.3.5.3.39 <softwaremaint> Additional maintenance task E.5.3.5.3.40 <other.maintsk>

Follow-on maintenance E.5.3.5.3.41 <followon.maintsk>

GENERAL MAINTENANCE

E.5.3.7 <gen.maintwp>

LUBRICATION INSTRUCTIONS

E.5.3.8 <lubewp>

ILLUSTRATED LIST OF

MANUFACTURED ITEMS

WORK PACKAGE

(MAINTAINER LEVEL AND

ABOVE)

P E.5.3.10

Illustrated list of manufactured items introduction work package

E.5.3.10.1 <manu_items_introwp>

Manufacturing procedures work package

E.5.3.10.2 <manuwp>

TORQUE LIMITS WORK

PACKAGE (MAINTAINER

LEVEL AND ABOVE)

P E.5.3.11 <torquewp>

WIRING DIAGRAMS WORK

P E.5.3.12 <wiringwp>

AUXILIARY EQUIPMENT

E.5.2.6

<auxiliarycategory>

MAINTENANCE WORK

E.5.3.14 <auxeqpwp>

MANUFACTURED ITEMS

WORK PACKAGE

(MAINTAINER LEVEL AND

ABOVE)

P E.5.3.10

Illustrated list of manufactured items

E.5.3.10.1 <manu_items_introwp>

Manufacturing procedures work package

E.5.3.10.2 <manuwp>

TORQUE LIMITS WORK

P E.5.3.11 <torquewp>

WIRING DIAGRAMS WORK

P E.5.3.12 <wiringwp>

AMMUNITION

E.5.2.7

<ammunitioncategory>

AMMUNITION MAINTENANCE

E.5.3.15.1 <ammowp>

AMMUNITION MARKING

INFORMATION WORK

E.5.3.15.2 <ammo.markingwp>

FOREIGN AMMUNITION

(NATO) WORK PACKAGE

E.5.3.15.3 <natowp>

PARTS INFORMATION

(-10, -13, -14) (-13&P, -14&P)

APPENDIX F <pim>

INTRODUCTION WORK

F.5.3.5 <introwp>

REPAIR PARTS LIST WORK

F.5.3.6 <plwp>

REPAIR PARTS FOR SPECIAL

TOOLS WORK PACKAGE

P F.5.3.7 <stl_partswp>

KIT PARTS LIST WORK

P F.5.3.8 <kitswp>

BULK ITEM WORK PACKAGE P F.5.3.9 <bulk_itemswp>

SPECIAL TOOLS LIST WORK

P F.5.3.10 <stlwp>

NSN INDEX WORK PACKAGE P

F.5.3.11.1 <nsnindxwp>

P/N INDEX WORK PACKAGE P

F.5.3.11.2 <pnindxwp>

REFERENCE DESIGNATOR

INDEX WORK PACKAGE

P F.5.3.11.3 <refdesindxwp>

DESTRUCTION OF

EQUIPMENT TO PREVENT

ENEMY USE

If a separate destruction of material manual is not developed for this equipment, then the destruction chapter must be included.

APPENDIX H <dim>

ENEMY USE INTRODUCTION

H.5.3 <destruct-introwp>

Authority to destroy R

H.5.3.3 <authorize_to_destroy>

Reporting destruction R

H.5.3.4 <report_destruct>

General destruction information

H.5.3.5 <general_destruct_info>

Degree of destruction R

H.5.3.6

Essential components and spare parts

H.5.3.7 <component_spares>

ENEMY USE PROCEDURES

H.5.4 <destruct-materialwp>

Parts list H.5.4.3 <essential_spares>

Specific destruction procedures R

H.5.4.4 <proc>

SUPPORTING INFORMATION

Applicable supporting information work packages shall be arranged in the order in which they are presented here and numbered accordingly.

APPENDIX G <sim>

REFERENCES WORK PACKAGE R

G.5.2 <refwp>

INTRODUCTION FOR NON-

AVIATION TWO-LEVEL

MAINTENANCE MAC WORK

G.5.3.1 <macintrowp>

MAC WORK PACKAGE (NON-

AVIATION TWO-LEVEL)

G.5.3.3 <macwp>

COMPONENTS OF END ITEM

(COEI) AND BASIC ISSUE

ITEMS (BII) LISTS WORK

G.5.4 <coeibiiwp>

ADDITIONAL AUTHORIZATION

LIST (AAL) WORK PACKAGE

G.5.5 <aalwp>

EXPENDABLE AND DURABLE

ITEMS LIST WORK PACKAGE

G.5.6 <explistwp>

TOOL IDENTIFICATION LIST

G.5.7 <toolidwp>

MANDATORY REPLACEMENT

PARTS WORK PACKAGE

G.5.8 <mrplwp>

CRITICAL SAFETY ITEMS

G.5.9 <csi.wp>

SUPPORT ITEMS WORK

G.5.10 <supitemwp>

ADDITIONAL SUPPORTING

G.5.11 <genwp>

REAR MATTER R

5.2.3 <rear>

Glossary 5.2.3.1 <glossary>

Alphabetical index 5.2.3.2 <aindx>

DA Form 2028 R

5.2.3.3 <da2028>

Authentication page R

5.2.3.4 <authent>

Foldout pages 5.2.3.5 <foldsect>

Back cover R

5.2.3.6 <back>

Legend R - Required P - Prohibited Shaded - As Required

TABLE A-IV. Combined Maintenance and Maintenance with Parts Requirements matrix for

TM Content -24

-24&P

MIL-STD-40051-2C

FRONT MATTER

R 5.2.1 <paper.frnt>

Front cover

R 5.2.1.1 <frntcover> (MC) Promulgation letter 5.2.1.3 <promulgation> Warning summary R 5.2.1.4 <warnsum> Change transmittal page 5.2.1.5 <chgsheet> List of effective pages/work packages

R 5.2.1.6 <loepwp>

Title page

R 5.2.1.7 <titleblk> Table of contents

R 5.2.1.9 <contents>

How to use this manual

R 5.2.1.10 <howtouse>

CHAPTER 1.

GENERAL INFORMATION,

EQUIPMENT DESCRIPTION, AND

THEORY OF OPERATION

R APPENDIX B <gim>

GENERAL INFORMATION WORK

R B.5.2 <ginfowp>

Scope

R B.5.2.3 <scope> Maintenance forms, records, and reports

R B.5.2.4 <mfrr>

Reporting Equipment Improvement Recommendations (EIR)

R B.5.2.5 <eir>

Hand Receipt (HR) information B.5.2.6 <handreceipt> Corrosion Prevention and Control (CPC)

R B.5.2.7 <cpcdata>

Ozone Depleting Substances (ODS) B.5.2.8 <odsdata> Destruction of Army materiel to prevent enemy use

R B.5.2.9 <destructmat>

Preparation for storage or shipment

R B.5.2.10 <pssref> Warranty information B.5.2.11 <wrntyref> Nomenclature cross-reference list B.5.2.12 <nomenreflist> List of abbreviations

R B.5.2.13 <loa>

Quality of material

R B.5.2.15 <qual.mat.info> Safety, care, and handling B.5.2.16 <sftyinfo> Nuclear hardness B.5.2.17 <hcp> Calibration B.5.2.18 <calref> Item unique identification (IUID) B.5.2.19 <iuid> Supporting information for repair parts, special tools, TMDE, and support equipment

B.5.2.26 <supdata>

Copyright credit line B.5.2.27 <copyrt>

EQUIPMENT DESCRIPTION AND DATA

R B.5.3 <descwp>

Equipment characteristics, capabilities, and features

R B.5.3.3 <eqpinfo>

Location and description of major components

R B.5.3.4 <locdesc>

Differences between models B.5.3.5 <eqpdiff> Equipment data

R B.5.3.6 <eqpdata>

THEORY OF OPERATION WORK

R B.5.4 <thrywp>

MASTER INDEX

D.5.4.4

<masterindexcat egory>

TROUBLESHOOTING INDEX WORK

R D.5.5.5 <tsindxwp>

TROUBLESHOOTING PROCEDURES

The notation (*) indicates that at least one of the these content items shall be included

R APPENDIX D

D.5.4.2

<troublecategor y>

INTRODUCTION WORK PACKAGE D.5.5.3 <tsintrowp>

TROUBLESHOOTING INDEX WORK

*OPERATIONAL CHECKOUT WORK

D.5.5.8.3 <opcheckwp>

*TROUBLESHOOTING WORK

D.5.5.8.4 <tswp>

*COMBINED OPERATIONAL

CHECKOUT AND TROUBLESHOOTING

D.5.5.8.5 <opcheck-tswp>

PMCS

MAINTENANCE INSTRUCTIONS

PMCS may be in its own chapter or may be combined with other maintenance work packages in a maintenance chapter but not both

E.5.2.1

<pmcscategory>

PMCS INTRODUCTION WORK PACKAGE

R E.5.3.4.1 <pmcsintrowp>

PMCS, INCLUDING LUBRICATION

INSTRUCTIONS, WORK PACKAGE

R E.5.3.4.2 <pmcswp>

PMCS may be in its own chapter or may be combned with other maintenance work packages in a maintenance chapter but not both

R APPENDIX E

E.5.2.2 E.5.2.3

<maintenancepmc scategory> <maintenancecat egory>

SERVICE UPON RECEIPT WORK

R E.5.3.2 <surwp>

Service upon receipt tasks

R E.5.3.2.3 <surtsk> Siting E.5.3.2.3.1 <siting> Shelter requirements E.5.3.2.3.2 <shltr> Service upon receipt of materiel

R E.5.3.2.3.3 <surmat>

Installation instructions

R E.5.3.2.3.4 <install> Preliminary servicing of equipment E.5.3.2.3.5 <preserv> Preliminary checks and adjustment of

E.5.3.2.3.6 <prechkadj>

Preliminary calibration of equipment E.5.3.2.3.7 <precal> Circuit alignment E.5.3.2.3.8 <calign> Ammunition markings E.5.3.2.3.9.1 <mark> Classification of defects E.5.3.2.3.9.2 <ammo.defect> Ammunition handling E.5.3.2.3.9.3 <ammo.handling> Procedures to activate ammunition E.5.3.2.3.9.4 <arm> Additional service upon receipt task E.5.3.2.3.10 <other.surtsk> Follow-on maintenance E.5.3.2.3.11 <followon.maint sk>

EQUIPMENT/USER FITTING

INSTRUCTIONS WORK PACKAGE

E.5.3.3 <perseqpwp>

PMCS INTRODUCTION WORK PACKAGE E.5.3.4.1 <pmcsintrowp>

PMCS WORK PACKAGE E.5.3.4.2 <pmcswp>

MAINTENANCE WORK PACKAGES

R E.5.3.5 <maintwp> Maintenance tasks

R E.5.3.5.3 <maintsk>

Inspect E.5.3.5.3.2 <inspect> Test E.5.3.5.3.3 <test> Service E.5.3.5.3.4 <service> Adjust E.5.3.5.3.5 <adjust> Align E.5.3.5.3.6 <align> Calibrate E.5.3.5.3.7 <calibration> Remove E.5.3.5.3.8 <remove> Install E.5.3.5.3.9 <install>

Replace E.5.3.5.3.10 <replace> Repair E.5.3.5.3.11 <repair> Paint E.5.3.5.3.12 <paint> Overhaul E.5.3.5.3.13 <overhaul> Rebuild E.5.3.5.3.14 <rebuild> Lubricate E.5.3.5.3.15 <lube> Mark E.5.3.5.3.16 <mark> Pack E.5.3.5.3.17 <pack> Unpack E.5.3.5.3.18 <unpack> Preserve E.5.3.5.3.19 <preserv> Prepare for use E.5.3.5.3.20 <prepforuse> Assemble E.5.3.5.3.21 <assem> Disassemble E.5.3.5.3.22 <disassem> Clean E.5.3.5.3.23 <clean> Nondestructive inspection E.5.3.5.3.24 <ndi> Radio interference suppression E.5.3.5.3.25 <ris> Place in service E.5.3.5.3.26 <pis> Towing E.5.3.5.3.27 <tow> Jacking E.5.3.5.3.28 <jack> Parking E.5.3.5.3.29 <park> Mooring E.5.3.5.3.30 <moor> Covering E.5.3.5.3.31 <cover> Hoisting E.5.3.5.3.32 <hoist> Sling loading E.5.3.5.3.33 <sling> External power E.5.3.5.3.34 <extpwr> Preparation for shipment and storage E.5.3.5.3.35 <pss> Arm E.5.3.5.3.36 <arm> Load E.5.3.5.3.37 <load> Unload E.5.3.5.3.38 <unload> Software maintenance E.5.3.5.3.39 <softwaremaint> Additional maintenance task E.5.3.5.3.40 <other.maintsk> Follow-on maintenance E.5.3.5.3.41 <followon.maint sk>

GENERAL MAINTENANCE WORK

E.5.3.7 <gen.maintwp>

LUBRICATION INSTRUCTIONS WORK

E.5.3.8 <lubewp>

MANUFACTURED ITEMS WORK

E.5.3.10

Illustrated list of manufactured items

R E.5.3.10.1 <manu_items_int rowp> Manufacturing procedures work package

R E.5.3.10.2 <manuwp>

TORQUE LIMITS WORK PACKAGE E.5.3.10.2 <torquewp>

WIRING DIAGRAMS WORK PACKAGE E.5.3.11 <wiringwp>

E.5.2.6

<auxiliarycateg ory>

MAINTENANCE WORK PACKAGE

E.5.3.14 <auxeqpwp>

MANUFACTURED ITEMS WORK

E.5.3.10

Illustrated list of manufactured items

R E.5.3.10.1 <manu_items_int rowp> Manufacturing procedures work package

R E.5.3.10.2 <manuwp>

TORQUE LIMITS WORK PACKAGE E.5.3.11 <torquewp>

WIRING DIAGRAMS WORK PACKAGE E.5.3.12 <wiringwp>

AMMUNITION

E.5.2.7

<ammunitioncate gory>

AMMUNITION MAINTENANCE WORK

E.5.3.15.1 <ammowp>

AMMUNITION MARKING

INFORMATION WORK PACKAGE

E.5.3.15.2 <ammo.markingwp

FOREIGN AMMUNITION (NATO) WORK

E.5.3.15.3 <natowp>

PARTS INFORMATION

(–23, –24) (–23&P, –24&P)

APPENDIX F <pim>

INTRODUCTION WORK PACKAGE

R F.5.3.5 <introwp>

REPAIR PARTS LIST WORK PACKAGE

R F.5.3.6 <plwp>

REPAIR PARTS FOR SPECIAL TOOLS

F.5.3.7 <stl_partswp>

KIT PARTS LIST WORK PACKAGE F.5.3.8 <kitswp>

BULK ITEM WORK PACKAGE F.5.3.9 <bulk_itemswp>

SPECIAL TOOLS LIST WORK PACKAGE F.5.3.10 <stlwp>

NSN INDEX WORK PACKAGE

R F.5.3.11.1 <nsnindxwp>

P/N INDEX WORK PACKAGE

R F.5.3.11.2 <pnindxwp>

REFERENCE DESIGNATOR INDEX

F.5.3.11.3 <refdesindxwp>

DESTRUCTION OF EQUIPMENT TO

PREVENT ENEMY USE

If a separate destruction of material manual is not developed for this equipment, then the destruction chapter must be included.

APPENDIX H <dim>

PREVENT ENEMY USE INTRODUCTION

H.5.3 <destruct-introwp>

Authority to destroy R H.5.3.3 <authorize_to_destro y>

Reporting destruction R H.5.3.4 <report_destruct>

General destruction information R H.5.3.5 <general_destruct_in fo>

Degree of destruction R H.5.3.6

Essential components and spare parts H.5.3.7 <component_spares>

PREVENT ENEMY USE PROCEDURES WORK

H.5.4 <destruct-materialwp>

Parts list H.5.4.3 <essential_spares>

Specific destruction procedures R H.5.4.4 <proc>

SUPPORTING INFORMATION

Applicable supporting information work packages shall be arranged in the order in which they are presented here and numbered accordingly.

R APPENDIX G <sim>

REFERENCES WORK PACKAGE

R G.5.2 <refwp>

INTRODUCTION FOR NON-AVIATION TWO-

LEVEL MAC WORK PACKAGE

R G.5.3.1 <macintrowp>

NON-AVIATION TWO-LEVEL MAC WORK

R G.5.3.3 <macwp>

EXPENDABLE AND DURABLE ITEMS WORK

R G.5.6 <explistwp>

TOOL IDENTIFICATION LIST WORK

G.5.7 <toolidwp>

MANDATORY REPLACEMENT PARTS WORK

G.5.8 <mrplwp>

CRITICAL SAFETY ITEMS WORK PACKAGE G.5.9 <csi.wp>

SUPPORT ITEMS WORK PACKAGE G.5.10 <supitemwp>

ADDITIONAL SUPPORTING WORK

G.5.11 <genwp>

REAR MATTER

R 5.2.3 <rear>

Glossary 5.2.3.1 <glossary>

Alphabetical index 5.2.3.2 <aindx>

DA Form 2028

R 5.2.3.3 <da2028>

Authentication page

R 5.2.3.4 <authent>

Foldout pages 5.2.3.5 <foldsect>

Back cover

R 5.2.3.6 <back>

Legend R - Required P - Prohibited Shaded - As Required