Attachment_5_-_FES_PPE_Technical_Evaluation_Matrix.xlsx

XLSX spreadsheet 167 KB Posted

Attached to
USAF Fire Emergency Services Personal Protective Services (FES PPE) Ensemble Federal contract opportunity
Solicitation number
FA8056-17-R-0001
Issued by
Department of the Air Force Materiel Command Installation and Mission Support Center Installation Contracting Agency

About this file

From the source

Attachment 5 - FES PPE Technical Evaluation Matrix

View the file

Other files for this federal contract opportunity

Other files attached to USAF Fire Emergency Services Personal Protective Services (FES PPE) Ensemble, newest first.
File Type Posted
Attachment_Change_Matrix_-_2-XX-2017.xlsx XLSX spreadsheet
FA8056-17-R-0001_0004_SF_30.pdf PDF
Attachment_5_-_FES_PPE_Technical_Evaluation_Matrix.xlsx XLSX spreadsheet
Attachment_3_-_FES_PPE_Ensemble_Product_Category_Specifications.xlsx XLSX spreadsheet
FA8056-17-R-0001_Final_RFP_Q&A_posted_02_02_17.pdf PDF
DoD_EMALL_-_Registration_Process_Improvement_Guide.pdf PDF
DOD_EMALL_-_Supplier_Informational_Package.pdf PDF
Attachment_2_-_FES_PPE_Ensemble_Pricing_Matrix.xlsx XLSX spreadsheet
Attachment_Change_Matrix_-_1-27-2017.xlsx XLSX spreadsheet
DoD_EMALL_-_Contractor_Registration.pdf PDF
DoD_EMALL_-_Supplier_Registration_-_CAC-PKI.pdf PDF
FA8056-17-R-0001_0003.docx DOCX document
FA8056-17-R-0001_0003_SF30.pdf PDF
FA8056-17-R-0001_Final_RFP_posted_01_27_17.docx DOCX document
Attachment_5_-_FES_PPE_Technical_Evaluation_Matrix.xlsx XLSX spreadsheet
FA8056-17-R-0001_Final_RFP_posted_01_26_17.docx DOCX document
FA8056-17-R-0001_0002_SF_30.pdf PDF
FA8056-17-R-0001_0002_SF_30.docx DOCX document
FA8056-17-R-0001_0002.docx DOCX document
Attachment_4_-_FES_PPE_Ensemble_Statement_of_Work.pdf PDF
Attachment_5_-_FES_PPE_Technical_Evaluation_Matrix.xlsx XLSX spreadsheet
Attachment_Change_Matrix_-_1-19-2017.xlsx XLSX spreadsheet
Attachment_2_-_FES_PPE_Ensemble_Pricing_Matrix.xlsx XLSX spreadsheet
Attachment_3_-_FES_PPE_Ensemble_Product_Category_Specifications.xlsx XLSX spreadsheet
Attachment_6_-_FES_PPE_Past_Performance_Questionnaire.pdf PDF
FA8056-17-R-0001_Final_RFP_posted_01.17.17.docx DOCX document
usps-military-mail-guide[1].pdf PDF
FA8056-17-R-0001_Draft_RFP_posted.pdf PDF
Attachment_3_-_FES_PPE_Ensemble_Product_Category_Specifications.xlsx XLSX spreadsheet
FA8056-17-R-0001.docx DOCX document
Attachment_4_-_FES_PPE_Ensemble_Statement_of_Work.pdf PDF
Attachment_1_-_FES_PPE_Ensemble_Proposal_Cover_Sheet.xlsx XLSX spreadsheet
Attachment_2_-_FES_PPE_Ensemble_Pricing_Matrix.xlsx XLSX spreadsheet
Attachment_6_-_FES_PPE_Past_Performance_Questionnaire_boxed.pdf PDF
Attachment_9_-_CDRL_A002.pdf PDF
Attachment_8_-_CDRL_A001.pdf PDF
Attachment_7_-_FES_PPE_List_of_USAF_Fire_Stations.xlsx XLSX spreadsheet
FA8056-17-R-0001_0001.pdf PDF
FA8056-17-R-0001_Draft_RFP.pdf PDF
Attachment_2_-_FES_PPE_Ensemble_Pricing_Matrix.xlsx XLSX spreadsheet
CDRL_A001.pdf PDF
Attachment_1_-_FES_PPE_Ensemble_Proposal_Cover_Sheet.xlsx XLSX spreadsheet
CDRL_A002.pdf PDF
Attachment_4_-_FES_PPE_Ensemble_Statement_of_Work.pdf PDF
Attachment_6_-_FES_PPE_Past_Performance_Questionnaire.pdf PDF
Attachment_5_-_FES_PPE_Technical_Evaluation_Matrix.pdf PDF
Attachment_3_-_FES_PPE_Ensemble_Product_Category_Specifications.xlsx XLSX spreadsheet
Attachment_7_-_FES_PPE_List_of_USAF_Fire_Stations.xlsx XLSX spreadsheet
Show all 48

On GovTribe

Work with this file on GovTribe

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file
Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

Instructions ATTACHMENT 5 - FES PPE Technical Evaluation Matrix

NOTE: Attachment 5 - FES PPE Technical Evaluation Matrix is for REFERENCE PURPOSES ONLY. Offerors shall not complete or submit Attachment 5 - FES PPE Technical Evaluation Matrix as part of their proposal; however, the Government urges Offerors to use this attachment when selecting and compiling substantiating documentation.

The Technical Evaluation Team will use the evaluation criteria in Attachment 5 – FES PPE Technical Evaluation Matrix to confirm all provided substantiating documentation meet the applicable technical specifications. Each piece of substantiating documentation will be evaluated on a pass/fail basis and assigned ratings of “Acceptable” or “Unacceptable” in accordance with Addendum 52.212-2 Section M - Evaluation Factors for Award.

The BOLDED text in column A under each technical requirement highlights the specific elements the Technical Evaluation Team will use to deem a requirement "Acceptable" or "Unacceptable".

FA8056-17-R-0001

Attachment 3 FES PPE Ensemble Product Category Specifications

TAB-A Structural Garments

Offeror:
CAGE Code:
Date of Completion:
Product Category A: Structural firefighting garments (i.e., coats, pant, and suspenders)
Specification SectionMeets/Does Not Meet SpecificationVolume & Page # and/or reference in ProposalSubstantiating DocumentationNotes
If "or equal" is proposedProvide product documentation that validates the product meets the specification as statedProvide commercial product sample that validates the product meets the specification as statedProvide Third Party certification (i.e. from SEI, UL, etc.)Provide formal product testing results that validate the product meets the specification as statedAcceptableMeetsProvided
Provide product documentation that validates product's equivalency to the brand name salient characteristics (reference "Instructions" tab)Provide formal product testing results that validate the product meets the specification as statedUnacceptableDoes Not MeetNot Provided
1.0. SPECIFICATIONS FOR STRUCTURAL FIRE FIGHTING COAT AND PANTS
1.1 THIRD PARTY TESTING
1.1.1 Third Party Testing and Listing Program. All components used in the construction of these garments shall have been tested, certified, and listed for compliance to NFPA 1971 by UL, SEI, ITS/ETL, or other(s).N/AN/AN/AN/AN/A
Coat meets NFPA 1971
Pants meets NFPA 1971
1.2. GARMENT OVERLAP
1.2.1. Garment Overlap. Coat and pant shall be produced by the same manufacturer to meet or exceed NFPA 1500 overlap (interface) requirements (2-inch or 50mm overlap of all layers).N/AN/AN/AN/AN/A
Coat and pants overlap is at least 2-inch and meets NFPA 1500.
1.3. SIZING
1.3.1. Sizing. Coats and Pants shall be available in men & women’s sizing.N/AN/AN/AN/AN/A
Sizing: Available in Mens
Sizing: Available in Womens
1.3.2 Coat Sizing. Chest shall be available for men in 34-60 inches and women in 28-50 inches in 2 inch increments. Sleeves shall be available for men in 32-38 inches and women in 28-34 inches in 2 inch increments or less. Generalized sizing, such as small, medium, large, etc., will not be accepted.N/AN/AN/AN/AN/A
Chest: Men 34-60 inches
Chest: Women 28-50 inches
Chest: All sizes available in 2 inch increments
Sleeves: Men 32-38 inches
Sleeves: Women 28-34 inches
Sleeves: All sizes available in 2 inch increments
Coats do not come in generalized sizing
1.3.3. Pant Sizing. The pants shall be available in men & women’s sizing and shall be sized for both waist and inseam. Waist shall be available for men in 30-60 inches and women in 28-50 inches in 2 inch increments. Inseam shall be available for men in 26-36 inches and women in 24-34 inches in 2 inch increments. Generalized sizing, such as small, medium, large, etc., will not be accepted.N/AN/AN/AN/AN/A
Waist: Men 30-60 inches
Waist: Women 28-50 inches
Waist: All sizes available in 2 inch increments
Inseam: Men 26-36 inches
Inseam: Women 24-34 inches
Inseam: All sizes available in 2 inch increments
Pants do not come in generalized sizing
1.3.4. Specialty Sizing. The contractor shall provide specialty sizes, at no additional cost of the item, if and when the Government determines appropriate sizing for a given purchase to be outside of the sizing parameters in 1.3.2 and 1.3.3.N/AN/AN/AN/AN/A
The contractor does provide specialty sizes, at no additional cost of the item.
1.3.5. Personnel Sizing. The contractor shall provide a controlled sample sizing kit with measurement guide and instructions on how to properly size the following: coat chest, coat sleeve, pant waist, pant inseam, and pant hips (women).N/AN/AN/AN/AN/A
The contractor does provide a controlled sample sizing kit with measurement guide.
The contractor does provide a controlled sample sizing kit with instructions.
The instructions include information on how to properly size the following: coat chest, coat sleeve, pant waist, pant inseam, and pant hips (women).
The instructions include information on how to properly size the following: coat chest.
The instructions include information on how to properly size the following: coat sleeve.
The instructions include information on how to properly size the following: pant waist.
The instructions include information on how to properly size the following: pant inseam.
The instructions include information on how to properly size the following: pant hips (women).
1.3.5.1. Sizing Kit. The contractor shall provide a controlled sample sizing kit with measurement guide and instructions on how to properly size men and women to capture proper fit and accurate interfacing of sleeve/glove, coat/pant, and pant/boot. Kit contents shall include a maximum of seven skipped size sets of coats and pants with common identified sleeve/pant lengths within the sizing ranges identified in 1.3.2. and 1.3.3.. above and utilized to capture sizing for structural and/or proximity (reference 10.2.4. for proximity) coat and pants. Sizing garments shall be easily identifiable or clearly marked as sizing garments to prevent utilization as compliant PPE garments.N/AN/AN/AN/AN/A
The contractor did provide a controlled sample sizing kit with measurement guide and instructions on how to properly size men and women.
The sizing kit captures proper fit and accurate interfacing of sleeve/glove.
The sizing kit captures proper fit and accurate interfacing of coat/pant.
The sizing kit captures proper fit and accurate interfacing of pant/boot.
Kit contents include a maximum of seven skipped size sets of coats and pants with common identified sleeve/pant lengths.
Sizing garments are easily identifiable or clearly marked as sizing garments to prevent utilization as compliant PPE garments.
1.3.5.2. Bench Stock Sizing. The contractor shall provide a specific sizing chart from the manufacturer to include sizing ranges and assist with determination of sizing for PPE in support of sustainment bench stock or bulk requirements.N/AN/AN/AN/AN/A
The contractor does provide a specific sizing chart from the manufacturer to include sizing ranges and assist with determination of sizing for PPE in support of sustainment bench stock or bulk requirements.
1.4. THE COMPOSITE (OUTER SHELL, MOISTURE BARRIER, AND THEMAL LINER)
1.4.1. Thermal Protective Performance (TPP). The structural coat and pants shall have a minimum TPP rating of 38 across the composite (outer shell, moisture barrier, thermal liner) throughout the garment.N/AN/AN/A
TPP Rating not less than 38 - Coat.
TPP Rating not less than 38 - Pants.
1.4.2. Total Heat Loss (THL). The Structural coat and pants shall have a minimum THL rating of 239 W/m2 across the composite (outer shell, moisture barrier, thermal liner).N/AN/AN/A
THL Rating not less than 239 W/m2 - Coat.
THL Rating not less than 239 W/m2 - Pants.
1.5. OUTER SHELL MATERIAL
1.5.1. Outer Shell Material. The outer shell shall be GEMINI® or equal material and comply with the following:N/AN/AN/A
The outer shell is GEMINI® or equal material.
1.5.2. Flexibility. The outer shell shall have flexibility after a 17.5 second NFPA minimum TPP exposure of 2.0 cal/cm2/seconds. The outer shell fabric shall remain flexible after this exposure and it shall not break open when folded and creased aggressively.N/AN/AN/A
Outer shell has flexibility after a 17.5 second NFPA minimum TPP exposure of 2.0 cal/cm2/seconds.
Outer shell fabric shall remain flexible after this exposure and it shall not break open when folded and creased aggressively.
1.5.3. Tear Strength (ASTM D5587). The outer shell fabric shall have a tear strength greater than 33 (lbf) (Warp) and 33 (lbf) (Fill) for initial testing and after five launderings.N/AN/AN/A
Outer shell fabric has a tear strength greater than 33 (lbf) (Warp).
Outer shell fabric has 33 (lbf) (Fill) for initial testing and after five launderings.
1.5.4. Tensile Strength (ASTM D5034). The outer shell shall have a tensile strength greater than 220 (lbf) (Warp) and 210 (lbf) (Fill) for initial testing.N/AN/AN/A
Outer shell has a tensile strength greater than 220 (lbf) (Warp).
Outer shell has 210 (lbf) (Fill) for initial testing.
1.5.5. Abrasion Resistance (ASTM D3884). The outer shell fabric shall have a durable water-repellent finish to enhance abrasion resistance. The outer shell fabric shall show no excessive wear upon visual inspections after 2,500 cycles of Taber abrasion testing using H18 abradant wheels and 500 gm initial weight.N/AN/AN/A
The outer shell fabric shall have a durable water-repellent finish to enhance abrasion resistance.
The outer shell fabric shall show no excessive wear upon visual inspections after 2,500 cycles of Taber abrasion testing.
1.5.6. Water Absorption Resistance (AATCC 42). The outer shell shall have a water absorption resistance of no greater than 10% after five launderings.N/AN/AN/A
The outer shell does have a water absorption resistance of no greater than 10% after five launderings.
1.5.7. Flame Resistance (ASTM D6413). The outer shell shall have a char length no greater than 1.0 in. (Warp) and 1.0 in. (Fill) after five launderings.N/AN/AN/A
Outer shell shall have a char length no greater than 1.0 in. (Warp).
Outer shell has a char length of 1.0 in. (Fill) after five launderings.
1.5.8. Heat and Thermal Shrinkage (NFPA 1971). The outer shell shall have a heat and thermal shrinkage/resistance no greater than 1.5% (Warp x Fill) in initial testing.N/AN/AN/A
The outer shell does have a heat and thermal shrinkage/resistance no greater than 1.5% (Warp x Fill) in initial testing.
1.5.9. Degradation Temperature. The outer shell shall withstand temperatures in excess of 1,100°F before degrading to the point of losing complete physical integrity; breaking apart with bending or movement.N/AN/AN/A
The outer shell does withstand temperatures in excess of 1,100°F before degrading to the point of losing complete physical integrity; breaking apart with bending or movement.
1.5.10. Color. The garment outer shell shall be uncolored natural fiber or colored gold.N/AN/AN/AN/A
The garment outer shell is uncolored natural fiber or colored gold.
1.5.11. DEFINITION. Further mentioning of “Outer Shell” requirements for structural PPE specifications shall refer to this section (i.e. 1.5)
1.6. THREE LAYER MOITURE BARRIER
1.6.1. The primary garment moisture barrier material shall be CROSSTECH® three (3)-layer moisture barrier - Type 4A, or equal material and utilized throughout coat and pants except where indicated. The moisture barrier shall be sewn and bound to the the thermal liner at the edges only with binding tape. Moisture barrier shall provide protection against water penetration resistance, viral penetration resistance, and "common chemical" penetration resistance as outlined in NFPA 1971.N/AN/AN/AN/A
CROSSTECH® 4A (3-layer) used in coat.
CROSSTECH® 4A (3-layer) used in pants.
The moisture barrier shall be sewn and bound to the thermal liner at the edges only with binding tape.
Moisture barrier meets NFPA 1971 (water penetration resistance, etc. ).
1.6.2. Sealed Moisture Barrier Seams. All moisture barrier seams shall be sealed with 1-inch wide waterproof membrane sealant tape made of moisture barrier membrane material used along seams and stitch holes to ensure they are sealed utilizing a heat activated glue adhesive.N/AN/AN/AN/A
All moisture barrier seams is be sealed with 1-inch wide waterproof membrane sealant tape made of moisture barrier membrane material used along seams and stitch holes to ensure they are sealed utilizing a heat activated glue adhesive.
1.6.3. Elevated Temperature Performance. The moisture barrier and seam tape shall not melt, ignite, or stick to the thermal liner when exposed to an elevated temperature of 500°F for five minutes.N/AN/AN/A
The moisture barrier and seam tape shall not melt, ignite, or stick to the thermal liner when exposed to an elevated temperature of 500°F for five minutes.
1.6.4. Thermal Stability. The moisture barrier laminate shall not show an increase of more than 2.0 m2Pa/W from its initial water-vapor resistance after being exposed to an elevated temperature of 500°F for five minutes when tested according to ISO 11092, Textile - Physiological - Measurements of thermal and water vapor resistance under steady-state conditions (sweating guarded-hotplate test).N/AN/AN/A
The moisture barrier laminate does not show an increase of more than 2.0 m2Pa/W from its initial water-vapor resistance after being exposed to an elevated temperature of 500°F for five minutes when tested according to ISO 11092 (sweating guarded-hotplate test).
1.6.5. Tear Strength (ASTM D5587). The moisture barrier fabric shall have a minimum tear strength score of 130 (lbf) (Warp) and 126 (lbf) (Fill) for initial testing.N/AN/AN/A
The moisture barrier fabric is have a minimum tear strength score of 130 (lbf) (Warp) and 126 (lbf) (Fill) for initial testing.
1.6.6. Flame Resistance (ASTM D6413). The moisture barrier shall have a char length no greater than 0.8 (in) (Warp) and 0.8 (in) (Fill) afterflame during initial testing.N/AN/AN/A
The moisture barrier has a char length no greater than 0.8 (in) (Warp) and 0.8 (in) (Fill) afterflame during initial testing.
1.6.7. Heat and Thermal Shrinkage (NFPA 1971). The moisture barrier shall have a heat and thermal shrinkage/resistance of no greater than -2.5% (Warp) and -2.8% (Fill) during initial testing.N/AN/AN/A
The moisture barrier hase a heat and thermal shrinkage/resistance of no greater than -2.5% (Warp) and -2.8% (Fill) during initial testing.
1.6.8. Cleaning/Laundry Shrinkage Resistance (AATCC 135). The moisture barrier shall have a shrinkage resistance of no greater than -4.0% (Warp) and -4.1% (Fill) during initial testing after five launderings.N/AN/AN/A
The moisture barrier has a shrinkage resistance of no greater than -4.0% (Warp) and -4.1% (Fill) during initial testing after five launderings.
1.6.9. DEFINITION. Further mentioning of “3-Layer Moisture Barrier” or “moisture barrier” requirements in this specification shall refer to this section (i.e. section 1.6) and shall be utilized as the baseline barrier material except where specifically noted.
1.7. TWO LAYER MOISTURE BARRIER
1.7.1. Two (2) - Layer Moisture Barrier Material. The moisture barrier material shall be CROSSTECH® Black two (2) - layer moisture barrier – Type 2F, or equivalent material and utilized only where specifically indicated. The moisture barrier shall provide protection against water penetration resistance, viral penetration resistance, and 'common chemical' penetration resistance as outlined in NFPA 1971.N/AN/AN/AN/A
CROSSTECH® Black 2F (2-layer) used where indicated.
Moisture Barrier Material meets NFPA 1971 (water penetration resistance, etc. ).
1.7.2. Elevated Temperature Performance. The moisture barrier and seam shall not melt, ignite, or stick to the thermal liner when exposed to an elevated temperature of 500°F for five minutes.N/AN/AN/A
The moisture barrier and seam tape does not melt, ignite, or stick to the thermal liner when exposed to an elevated temperature of 500°F for five minutes.
1.7.3. Thermal Stability (ISO 11092). The moisture barrier laminate shall not show an increase of more than 2.0 m2Pa/W from its initial water-vapor resistance after being exposed to an elevated temperature of 500°F for five minutes when tested according to ISO 11092 (sweating guarded-hotplate test).N/AN/AN/A
The moisture barrier laminate does not show an increase of more than 2.0 m2Pa/W from its initial water-vapor resistance after being exposed to an elevated temperature of 500°F for five minutes when tested according to ISO 11092 (sweating guarded-hotplate test).
1.7.4. Tear Strength (ASTM D5587). The moisture barrier fabric shall have a minimum tear strength score of 72 (lbf) (Warp) and 89 (lbf) (Fill) for initial testing.N/AN/AN/A
The moisture barrier fabric has a minimum tear strength score of 72 (lbf) (Warp) and 89 (lbf) (Fill) for initial testing.
1.7.5. Flame Resistance (ASTM D6413). The moisture barrier shall have a char length greater than 1.6 (in) (Warp) and 0.8 (in) (Fill) afterflame during initial testing.N/AN/AN/A
The moisture barrier has a char length greater than 1.6 (in) (Warp) and 0.8 (in) (Fill) afterflame during initial testing.
1.7.6. Heat and Thermal Shrinkage (NFPA 1971). The moisture barrier shall have a heat and thermal shrinkage/resistance of no greater than -4.0% (Warp) and -3.5% (Fill) during initial testing.N/AN/AN/A
The moisture barrier has a heat and thermal shrinkage/resistance of no greater than -4.0% (Warp) and -3.5% (Fill) during initial testing.
1.7.7. Cleaning/Laundry Shrinkage Resistance (AATCC 135). The moisture barrier shall have a shrinkage resistance of no greater than -4.1% (Warp) and -2.8% (Fill) during initial testing after five launderings.N/AN/AN/A
The moisture barrier has a shrinkage resistance of no greater than -4.1% (Warp) and -2.8% (Fill) during initial testing after five launderings.
1.7.8. DEFINITION Further mentioning of "2-Layer Moisture Barrier" requirements in this specification shall refer to this section (i.e., Section 1.6) expect where specifically noted.
1.8. THERMAL LINER
1.8.1. The Liner Material. The thermal liner is constructed of “CALDURA® SL2i” or equal material.N/AN/AN/AN/A
The thermal liner is constructed of “CALDURA® SL2i” or equal material.
1.8.2. Wickability (AATCC 79). Thermal liner shall have a facecloth wickability performance of 10 seconds or less.N/AN/AN/A
Thermal liner has a facecloth wickability performance of 10 seconds or less.
1.8.3. Slickness. Thermal liner has a facecloth constructed utilizing spun and filament yarns.N/AN/AN/AN/A
Thermal liner has a facecloth constructed utilizing spun and filament yarns.
1.8.4. Pilling (ASTM D3512). Thermal liner facecloth shall have a rating of 4 (Slight Pilling) or 5 (No Pilling) both before and after washing agitation at 30, 60, and 90 minute intervals.N/AN/AN/A
Thermal liner facecloth has a rating of 4 (Slight Pilling) or 5 (No Pilling) both before and after washing agitation at 30, 60, and 90 minute intervals.
1.8.5. Thermal Batting/Spun Lace. Thermal liner shall have two layers of spun lace to decrease the likelihood of compression burns.N/AN/AN/AN/A
Thermal liner has two layers of spun lace to decrease the likelihood of compression burns.
1.8.6. Tear Strength (ASTM D5587). The thermal liner fabric shall have a tear strength greater than 40 (lbf) (Warp) and 100 (lbf) (Fill) for initial testing.N/AN/AN/A
The thermal liner fabric has a tear strength greater than 40 (lbf) (Warp) and 100 (lbf) (Fill) for initial testing.
1.8.7. Flame Resistance (ASTM D6413). The thermal liner shall have a char length no greater than 2.0 (in) (Warp) and 2.0 (in) (Fill) for initial testing.N/AN/AN/A
The thermal liner has a char length no greater than 2.0 (in) (Warp) and 2.0 (in) (Fill) for initial testing.
1.8.8. Heat and Thermal Shrinkage (NFPA 1971). The thermal liner has a heat and thermal shrinkage/resistance of no greater than 3.5% (Warp x Fill) at 500°F for five minutes.N/AN/AN/A
The thermal liner has a heat and thermal shrinkage/resistance of no greater than 3.5% (Warp x Fill) at 500°F for five minutes.
1.8.9. Cleaning/Laundry Shrinkage Resistance (AATCC 135). The thermal liner shall have a shrinkage resistance of no greater than 5% (Warp x Fill) at 500°F for five minutes.N/AN/AN/A
The thermal liner has a shrinkage resistance of no greater than 5% (Warp x Fill) at 500°F for five minutes.
1.8.10. DEFINITION. Further mentioning of "Thermal Liner" requirements on this specification shall refer to this section (i.e., Section 1.7) except where specifically noted.
1.9. REINFORCED FABRIC/MATERIAL
1.9.1 Reinforcement Fabric/Material. All areas of the structural coat and pants where applicable shall be strengthened with “reinforcement” Ara-shield® or equivalent material.N/AN/AN/AN/A
Coat strengthened with “reinforcement” Ara-shield® or equivalent material.
Pants strengthened with “reinforcement” Ara-shield® or equivalent material.
1.9.2. Abrasion Resistance (ASTM D3884). The reinforcement material shall have a durable water-repellent finish to enhance abrasion resistance. The reinforcement material shall not show excessive wear upon visual inspections after 9,500 cycles of Taber abrasion testing using H18 abradant wheels and 500 gm initial weight.N/AN/AN/AN/A
The reinforcement material has a durable water-repellent finish to enhance abrasion resistance.
The reinforcement material doesn't show excessive wear upon visual inspections after 9,500 cycles of Taber abrasion testing using H18 abradant wheels and 500 gm initial weight.
1.9.3. Tear Strength (ASTM D5587). The reinforcement fabric shall have a tear strength greater than 20 (lbf) (Warp) and 7 (lbf) (Fill) for initial testing.N/AN/AN/A
The reinforcement fabric has a tear strength greater than 20 (lbf) (Warp) and 7 (lbf) (Fill) for initial testing.
1.9.4. Flame Resistance (ASTM D6413). The reinforcement fabric shall have a char length no greater than 2.0 (in) (Warp) and 2.0 (in) (Fill) initial and after five launderings.N/AN/AN/A
The reinforcement fabric has a char length no greater than 2.0 (in) (Warp) and 2.0 (in) (Fill) initial and after five launderings.
1.9.5. Heat and Thermal Shrinkage (NFPA 1971). The reinforcement fabric shall have a heat and thermal shrinkage/resistance of no greater than 1.5% (Warp) and 1.5% (Fill) for initial testing.N/AN/AN/A
The reinforcement fabric has a heat and thermal shrinkage/resistance of no greater than 1.5% (Warp) and 1.5% (Fill) for initial testing.
1.9.6. Cleaning/Laundry Shrinkage Resistance (AATCC 135). The reinforcement fabric shall have a shrinkage resistance of no greater than 5.0% (Warp) and 5.0% (Fill) after five launderingsN/AN/AN/A
The reinforcement fabric has a shrinkage resistance of no greater than 5.0% (Warp) and 5.0% (Fill) after five launderings.
1.9.7. DEFINITION. Further mentioning of "Reinforcement" requirements in this specification shall refer to this section (Section 1.8) except where specifically noted
1.10. STITCHING
1.10.1. Stitching. The outer shell shall be assembled using stitch type #301, #401, #514 or #516. The thermal liners shall be assembled using stitch type #301, #401, #504, #514, or #516. The moisture barriers shall be assembled using stitch type #301, #401, #504, #514, or #516. Stitching in all seams shall be continuous. Major “A” outer shell structural seams shall have a minimum of 8 to 10 stitches per inch throughout. Major “B” structural liner seams shall have a minimum of 8 to 10 stitches per inch throughout.N/AN/AN/A
The outer shell is assembled using stitch type #301, #401, #514 or #516.
The thermal liners are assembled using stitch type #301, #401, #504, #514, or #516.
The moisture barriers are assembled using stitch type #301, #401, #504, #514, or #516.
Stitching in all seams is continuous.
Major “A” outer shell structural seams have a minimum of 8 to 10 stitches per inch throughout.
Major “B” structural liner seams have a minimum of 8 to 10 stitches per inch throughout.
1.11. INSPECTION ACCESS OPENING
1.11.1. Inspection Access Opening. The thermal liner shall have an accessibility opening for the purpose of inspecting the inner surfaces of the thermal liner system. The moisture barrier has an accessibility opening for the purpose of inspecting the inner surfaces of the moisture barrier and system. This thermal liner opening shall be completely secured with two strips of fire resistant hook and loop fastener or overlapped and secured. This moisture barrier opening shall be completely secured with two strips of fire resistant hook and loop fastener or overlapped and secured.N/AN/AN/AN/AN/A
The thermal liner has an accessibility opening for the purpose of inspecting the inner surfaces of the thermal liner system.
The moisture barrier has an accessibility opening for the purpose of inspecting the inner surfaces of the moisture barrier and system.
This thermal liner opening is completely secured with two strips of fire resistant hook and loop fastener or overlapped and secured.
This moisture barrier opening is completely secured with two strips of fire resistant hook and loop fastener or overlapped and secured.
1.12. LABELS
1.12.1. Labels. Appropriate warning label(s) are permanently affixed to each garment. Additionally, the label(s) shall include the following:N/AN/AN/AN/AN/A
Labels affixed to coat.
Labels affixed to pant.
1.12.2. Compliant with NFPA Standard 1971.N/AN/AN/AN/AN/A
Coat NFPA 1971 compliant.
Pants NFPA 1971 compliant.
1.12.3. Underwriters Laboratories and/or Safety Equipment Institute classified marked / labeled.N/AN/AN/AN/AN/A
Coat UL or SEI labeled.
Pants UL or SEI labeled.
1.12.4. A complete users information guide is included accordance with NFPA 1971 paragraph 5.4.4.N/AN/AN/AN/A
User guide included with coat.
User guide included with pants
1.13. ISO CERTIFICATION/REGISTRATION
1.13.1. ISO Certification/Registration. The protective clothing manufacturer is certified and registered to ISO Standard 9001 to assure a satisfactory level of quality.N/AN/AN/AN/AN/A
The manufacturer is certified and registered to ISO Standard 9001.
2.0. STRUCTURAL FIRE FIGHTING COAT
2.1. BODY
2.1.1. Body. The coat design shall be assembled to facilitate maximum unencumbered ease of movement across the shoulders, chest, and arms with the least amount of coat rise and restriction offered by the manufacturer utilizing no less than three separate panels. Coat shall provide a contoured fit and align at the seams with double stitching with Nomex® or equal flame resistant meta-aramid thread. The baseline coat length shall be no longer than 32-inches while shorter and longer lengths shall be available for sizing of tall and short personnel. Coat length may be longer in the back than in the front to facilitate interfacing requirements. The bottom hem of the coat shall be finished with a double row of stitching.N/AN/AN/AN/A
Is there unencumbered ease of movement across the shoulders with the least amount of coat rise and restriction.
Is there unencumbered ease of movement across the chest with the least amount of coat rise and restriction.
Is there unencumbered ease of movement across the arms with the least amount of coat rise and restriction.
Is there no less than three separate panels in the shoulders and in the shoulders.
Coat has a contoured fit and align at the seams with double stitching with Nomex® or equal flame resistant meta-aramid thread.
The baseline coat length is no longer than 32-inches.
Coat sizes in shorter and longer lengths are available for sizing of tall and short personnel.
Coat length is longer in the back than in the front to facilitate interfacing requirements.
The bottom hem of the coat is finished with a double row of stitching.
2.1.2. Collar & Throat Tab/Strap. The collar shall consist of a four-layer construction. The collar shall be minimum 3¼-inches high and lengthened to size. The front edges of the collar shall extend up so that no gap occurs at the throat. Where installed, all hook and loop fastener shall be oriented to prevent exposure to the environment. The throat tab/strap and/or collar shall facilitate adjustment when in the closed position and while wearing a breathing apparatus mask. If throat tab/strap is provided, it shall be able to be stored without creating interference to the user when not in use. A hanger loop shall be sewn to the top inside rear of the collar at the center, and be constructed to withstand hanging the full weight of the coat plus any gear typically attached when stored.N/AN/AN/AN/AN/A
The collar consists of a four-layer construction.
The collar is a minimum 3¼-inches high and lengthened to size.
The front edges of the collar extends up so that no gap occurs at the throat.
Where installed, all hook and loop fasteners are oriented to prevent exposure to the environment.
The throat tab/strap and/or collar facilitates adjustment when in the closed position and while wearing a breathing apparatus mask.
If throat tab/strap is provided, it's able to be stored without creating interference to the user when not in use.
A hanger loop is sewn to the top inside rear of the collar at the center, and be constructed to withstand hanging the full weight of the coat plus any gear typically attached when stored.
2.1.3. Inside Coat Pocket. A pocket measuring no less than 7-inch by 9-inch or greater than 9-inch by 9-inch, constructed of thermal liner material and lined with moisture barrier material, shall be affixed to the inside of the coat thermal liner on the left side with the pocket thermal liner and moisture barrier bound together around the perimeter.N/AN/AN/AN/AN/A
The pocket measuring no less than 7-inch by 9-inch or greater than 9-inch by 9-inch.
The pocket is constructed of thermal liner material and lined with moisture barrier material.
The pocket is affixed to the inside of the coat thermal liner on the left side with the pocket thermal liner andmoisture barrier bound together around the perimeter.
2.1.4. Front/Inside Facings. Separate facings shall measure 2-3-inches wide from collar to hem, and double stitched to the body panels. The facing composite shall be comprised of CROSSTECH® Black 2-layer moisture barrier material or equivalent and outer shell material. The coat thermal liner and moisture barrier shall be attached to the coat facings by means of snap fasteners.N/AN/AN/AN/AN/A
Separate facings measure 2-3-inches wide from collar to hem.
Facings are double stitched to the body panels.
The facing composite is comprised of CROSSTECH® Black 2-layer moisture barrier material or equivalent and outer shell material.
The coat thermal liner and moisture barrier is attached to the coat facings by means of snap fasteners.
2.1.5. Front Closure System. The coat shall be closed by means of a #10 heavy duty high temperature smooth-gliding non-conductive zipper made with plastic (polyacetal resin) that aligns each front facing. The teeth of the zipper shall be mounted on Nomex® or equal flame resistant meta-aramid tape. The storm flap shall measure 3-3½-inches wide and shall be centered. The outside storm flap shall include at least 1-layer of CROSSTECH® Black 2-layer moisture barrier material or equivalent and reinforced at both ends with bar-tacks. The storm flap shall close over the left and right coat body panels and shall be secured with fire resistant hook and loop fastener tape. A piece of fire resistant hook and loop fastener tape shall be installed along the leading edge of the storm flap on the underside. A corresponding piece of fire resistant hook and loop fastener tape shall be sewn to the front body panel and positioned to engage the loop fastener tape when the storm flap is closed over the front of the coat.N/AN/AN/AN/AN/A
The coat is closed by means of a #10 heavy duty high temperature smooth-gliding non-conductive zipper made with plastic (polyacetal resin) that aligns each front facing.
The teeth of the zipper are mounted on Nomex® or equal flame resistant meta-aramid tape.
The storm flap measures 3-3½-inches wide and shall be centered.
The outside storm flap has at least 1-layer of CROSSTECH® Black 2-layer moisture barrier material or equivalent and is reinforced at both ends with bar-tacks.
The storm flap closes over the left and right coat body panels and is secured with fire resistant hook and loop fastener tape.
A piece of fire resistant hook and loop fastener tape is installed along the leading edge of the storm flap on the underside.
A corresponding piece of fire resistant hook and loop fastener tape is sewn to the front body panel and positioned to engage the loop fastener tape when the storm flap is closed over the front of the coat.
2.1.6. Sleeves. The sleeves shall be shaped so as to provide a contoured fit following the natural flex of the arm at rest. The sleeve design shall facilitate the maximum unencumbered ease of movement across the shoulders, elbows, and arms with the least amount of coat rise and restriction offered by the manufacturer and properly interface with gauntlet style gloves.N/AN/AN/AN/AN/A
The sleeves are shaped so as to provide a contoured fit following the natural flex of the arm at rest.
The sleeve design does facilitate the maximum unencumbered ease of movement across the shoulders with the least amount of coat rise and restriction offered by the manufacturer and properly interface with gauntlet style gloves.
2.1.7. Sleeve Cuff Reinforcements. The sleeve cuffs shall be reinforced with Ara-shield® reinforcement fabric or equivalent material. Material shall be black in color and not be less than 2-inches in width and folded in half, approximately one half inside and one half outside the sleeve end and stitched to the sleeve end.N/AN/AN/AN/AN/A
The sleeve cuffs are reinforced with Ara-shield® reinforcement fabric or equivalent material.
Material is black in color and not be less than 2-inches in width and folded in half, approximately one half inside and one half outside the sleeve end and stitched to the sleeve end.
2.1.8. Wristlets/Sleeve Wells. Wristlets shall be constructed of a PBI blended Kevlar® or PBI blended Nomex® knit material with hand and wrist guards (over the hand) and separate thumbhole with an approximate diameter of 2-inches shall be recessed approximately 1-inch from the leading edge. Flame resistant barrier material impervious to fluids shall be incorporated to the inside of the sleeve shell to prevent fluids from entering the sleeve’s arm and wrist area. The wristlet and coat sleeve interface shall be designed so that it will not permit a gap in thermal protection and properly interfaces with gauntlet style gloves.N/AN/AN/A
Wristlets are constructed of a PBI blended Kevlar® or PBI blended Nomex® knit material with hand and wrist guards (over the hand) and separate thumbhole with an approximate diameter of 2-inches shall be recessed approximately 1-inch from the leading edge.
Flame resistant barrier material impervious to fluids is incorporated to the inside of the sleeve shell to prevent fluids from entering the sleeve’s arm and wrist area.
The wristlet and coat sleeve interface is designed so that it will not permit a gap in thermal protection and properly interfaces with gauntlet style gloves.
2.1.9. Liner Elbow Thermal Enhancement. An additional layer of thermal liner material shall be sewn to the elbow area and stitched to the thermal liner layer only. The finished dimension shall be approximately 5-inches by 7-inches.N/AN/AN/AN/AN/A
An additional layer of thermal liner material is sewn to the elbow area and stitched to the thermal liner layer only.
The finished dimension is approximately 5-inches by 7-inches.
2.1.10. Liner Shoulder and Upper Back Thermal Enhancement. An additional layer of thermal liner material shall provide shoulder and upper back thermal enhancement to provide greater conductive and compressive heat resistance (CCHR) protection IAW NFPA 1971. Material shall extend over the top of each shoulder side to side from the collar to the sleeve seems. The material shall extend over the front approximately 5-inches and the back approximately 7½-inches and stitched to the thermal liner only.N/AN/AN/AN/AN/A
An additional layer of thermal liner material is provided at shoulder and upper back thermal enhancement to provide greater conductive and compressive heat resistance (CCHR) protection IAW NFPA 1971.
Material does extend over the top of each shoulder side to side from the collar to the sleeve seems.
The material does extend over the front approximately 5-inches and the back approximately 7½-inches and stitched to the thermal liner only.
2.1.11. Drag Rescue Device (DRD). The DRD shall be constructed of 1½-inch wide Kevlar® or equivalent strap. The DRD shall have the ability to be “reset” without doffing the coat to reset the strap system. Access to the DRD strap will be through a covered access opening between the shoulders on the upper back with the flap secured by a fire resistant hook and loop fastener tape. When a Self-Contained Breathing Apparatus (SCBA) is worn, access or function of DRD strap, access opening, or flap shall not be impeded. The outside flap shall be constructed of outer shell material and have a NFPA-compliant 3M Scotchlite™ or equivalent retroreflective and fluorescent material patch or trim sewn to the outside of the flap to identify it as the DRD.N/AN/AN/AN/AN/A
The DRD is constructed of 1½-inch wide Kevlar® or equivalent strap. The DRD shall have the ability to be “reset” without doffing the coat to reset the strap system.
Access to the DRD strap is through a covered access opening between the shoulders on the upper back with the flap secured by a fire resistant hook and loop fastener tape.
When a Self-Contained Breathing Apparatus (SCBA) is worn, access or function of DRD strap, access opening, or flap is not be impeded.
The outside flap is constructed of outer shell material and have a NFPA-compliant 3M Scotchlite™ or equivalent retroreflective and fluorescent material patch or trim sewn to the outside of the flap to identify it as the DRD.
2.1.12. Liner Access Opening (Coat). Liner access shall be through an opening large enough to facilitate complete moisture barrier and liner inspection and securely close to prevent soiling. The thermal liner and moisture barrier shall be completely removable from the coat’s outer shell.N/AN/AN/AN/AN/A
Liner access is through an opening large enough to facilitate complete moisture barrier and liner inspection and securely close to prevent soiling.
The thermal liner and moisture barrier is completely removable from the coat’s outer shell.
2.1.13. Method of Thermal Liner/Moisture Barrier Attachment for Coat. The thermal liner/moisture barrier shall be secured to each coat facing and sleeve with snap fasteners. The outside perimeter of the moisture barrier and thermal liner layers shall be finished and securely bound.N/AN/AN/AN/AN/A
The thermal liner/moisture barrier is secured to each coat facing and sleeve with snap fasteners.
The outside perimeter of the moisture barrier and thermal liner layers are finished and securely bound.
2.1.14. Retroreflective Fluorescent Trim. The trim shall be 3M Scotchlite™ or equal retroreflective and fluorescent 3-inch lime/yellow with silver center stripe to enhance nighttime and daytime visibility. Each coat sleeve shall have one (1) stripe below each elbow and two (2) horizontal stripes on the coat body in accordance with NFPA 1971-13 figure 6.2.3 option #1. The reflective trim shall run over pockets and be sewn to the outer shell with a flame resistant meta-aramid Nomex® or equal thread with the ends secured into seams.N/AN/AN/A
The trim is 3M Scotchlite™ or equal retroreflective and fluorescent.
Trim is 3-inch lime/yellow with silver center stripe to enhance nighttime and daytime visibility.
Each coat sleeve has one (1) stripe below each elbow in accordance with NFPA 1971-13.
Each coat sleeve has two (2) horizontal stripes on the coat body in accordance with NFPA 1971-13.
The reflective trim does run over pockets and is sewn to the outer shell with a flame resistant meta-aramid Nomex® or equal thread with the ends secured into seams.
2.1.15. Cargo/Hand Warmer Expansion (Bellows) Pockets. One (1) pocket shall be provided and double stitched to the bottom of each front body panel where it can be fully utilized when used with an SCBA. The 2-inch expansion pocket shall measure no less than 8-inch wide by 8-inch high or greater than 10-inch wide by 10-inch high. For 32 inch baseline or shorter coat lengths –trim shall run over the bottom of the pockets. For 26-inch coat lengths –expansion pockets shall be either 10-inch wide by 6-inch high or 8-inches wide by 6-inches high. Two rust resistant metal drain grommets shall be installed in the bottom of each expansion pocket. Lower half of each pocket shall be reinforced with a layer of Kevlar® or equivalent on the inside. Pocket flaps shall be constructed of two layers of outer shell material approximately ½-inch wider than the pocket. Upper pocket corners shall be reinforced with back-tacks and pocket flaps shall be reinforced with bar-tacks. Two pieces of non-flammable and fire resistant hook and loop fastener tape shall be placed vertically on the inside of each pocket flap (one piece on each end). Two corresponding pieces of fire resistant hook and loop fastener tape shall be installed horizontally on the outside of each pocket near the top (one piece on each end) and positioned to engage the hook fastener tape. Additionally, a separate hand warmer pocket compartment shall be provided behind the expandable cargo pocket (between the outer shell and cargo pocket). This compartment shall be accessed from the rear of the pocket and lined with flame resistant meta-aramid Nomex® or equal fleece.N/AN/AN/AN/AN/A
One (1) pocket is provided and double stitched to the bottom of each front body panel where it can be fully utilized when used with an SCBA.
The 2-inch expansion pocket does measure no less than 8-inch wide by 8-inch high or greater than 10-inch wide by 10-inch high.
For 32 inch baseline or shorter coat lengths –trim does run over the bottom of the pockets.
For 26-inch coat lengths – expansion pockets are either 10-inch wide by 6-inch high or 8-inches wide by 6-inches high.
Two rust resistant metal drain grommets are installed in the bottom of each expansion pocket.
Lower half of each pocket are reinforced with a layer of Kevlar® or equivalent on the inside.
Pocket flaps are constructed of two layers of outer shell material approximately ½-inch wider than the pocket.
Upper pocket corners are reinforced with back-tacks and pocket flaps shall be reinforced with bar-tacks.
Two pieces of non-flammable and fire resistant hook and loop fastener tape are placed vertically on the inside of each pocket flap (one piece on each end).
Two corresponding pieces of fire resistant hook and loop fastener tape are installed horizontally on the outside of each pocket near the top (one piece on each end) and positioned to engage the hook fastener tape.
A separate hand warmer pocket compartment is provided behind the expandable cargo pocket (between the outer shell and cargo pocket).
The separate hand warmer pocket compartment is accessed from the rear of the pocket and lined with flame resistant meta-aramid Nomex® or equal fleece.
2.1.16. Radio Pocket. A portable radio pocket option shall be provided for either the left or right chest. The 2.5-inches deep pocket shall measure approximately 3.5-inches wide by 8-inches high and double stitched to the outer shell with one drainage grommet in the bottom of the pocket. The flap shall be two layers of outer shell material ¼-inch wider than the pocket width and notched on each side to accommodate a radio antenna from either side. Flap length shall measure 6-inches in length and secure by means of fire resistant hook and loop fastener tape. Flap hook and loop tape shall be 3-inches in length to facilitate adjustable closure. The pocket shall be lined with impervious barrier material and placed between the two layers of outer shell material in the pocket flap.N/AN/AN/AN/AN/A
Aportable radio pocket option is provided for either the left or right chest.
The 2.5-inches deep pocket does measure approximately 3.5-inches wide by 8-inches high.
The pocket is double stitched to the outer shell.
The pocket has one drainage grommet in the bottom of the pocket.
The pocket flap is two layers of outer shell material ¼-inch wider than the pocket width.
The pocket flap is notched on each side to accommodate a radio antenna from either side.
The pocket flap length is 6-inches in length.
The pocket flap is secured by means of fire resistant hook and loop fastener tape.
The pocket flap hook and loop tape is be 3-inches in length to facilitate adjustable closure.
The pocket is lined with impervious barrier material and placed between the two layers of outer shell material in the pocket flap.
2.1.17. Microphone Straps. Two (2) straps shall be constructed of outer shell material. One (1) shall be mounted above the radio pocket and the other above the flashlight hook on the opposite chest. The microphone straps shall be 1-inch by 2-inches and sewn to the coat using two rows of stitching at the ends only.N/AN/AN/AN/AN/A
Two (2) micorphone straps are constructed of outer shell material.
One (1) is mounted above the radio pocket and the other above the flashlight hook on the opposite chest.
The microphone straps are 1-inch by 2-inches.
The microphone straps are sewn to the coat using two rows of stitching at the ends only.
2.1.18. Flashlight Holder Hook and Retainer Strap. A flashlight holder hook and strap shall be provided and positioned on the opposite chest chosen from the portable radio pocket.N/AN/AN/AN/AN/A
The flashlight Holder Hook and strap is provided and positioned on the opposite chest chosen from the portable radio pocket.
2.1.18.1. Flashlight Hook. Hook shall face downward and inward and be triple riveted or bartacked with double thickness leather or Ara-Shield reinforcement in a vertical position to accept the clip of a flashlight.N/AN/AN/AN/AN/A
Hook faces downward.
Hook faces inward
Hook is triple riveted or bartacked with double thickness leather or Ara-Shield reinforcement in a vertical position to accept the clip of a flashlight.

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .