Attachment_D_-_Specification_4210-5617LTR.docx

State of California Specification Emergency Crew Transport Vehicle (ECT) Lettering/Stripping

4210-5617LTR

Attachment D

Middleton, B 7/18/2022

Document Summary

Revision History

1 EXTERIOR LETTERING/STRIPING

The contractor shall supply all graphics (shields, logos, letters, numbers, symbols, and striping) for the ECT and CAL FIRE shall provide a JPEG template of all decals at the pre-construction conference. All striping on rear and sides shall be 3 M brand 680 series Scotchlite plus for 6-inch white reflective tape. Red striping shall be 3M or equivalent for the 4-inch, and 1-inch red reflective tape. All striping shall begin and end ¼ inch before any shield, logo, or lettering. The lettering, shields, and graphics for the ECT shall match the pictures below and be free of bubbles, unnecessary breaks, jagged cuts, be straight, centered and be free of imperfections. All agency/department/carrier/radio/ECT specific identifiers shall be provided as part of the order.

Sides (Door and Buildup) Door

· CALFIRE cab door logo 14-inch door shields

· Motor Carrier Number CA-90002 shall be black non reflective two inch high with a 3/8 stroke width located ½ inch above the lower edge of the door centered.

· 6-inch reflective striping starting on hood side to rear of cab edge.

· 4-inch red reflective striping shall be installed along the lower horizontal edge inside both cab doors.

Buildup

· 6-inch white reflective Helvetica medium font department identifier above all side windows. (Examples: California Department of Corrections or California Conservation Corps.)

· Large “CAL FIRE” stacked decal CAL FIRE 11-inch typographic stacked Aerial Black 100%

· 6-inch white reflective Helvetica medium font camp identifier letters on both sides below middle window. (Example: Puerta La Cruz)

· 6-inch white reflective Helvetica medium font radio numbers and letters on both sides.

· 6-inch white reflective Helvetica medium font “FIRE CREW” letters on both sides.

· 6-inch reflective striping starting on front edge of body to rear edge.

· 4-inch red reflective striping shall be installed along the lower inside wall of all compartment doors.

Rear

· CALFIRE logo (left door) 14-inch door shield

· Radio numbers left rear tool compartment in stripe open area centered Helvetica medium font three letters one number.

· “CAL FIRE” decal (center crew door) CAL FIRE 6-inch typographic stacked Aerial Black100%

· Unit identifier right rear crew door in stripe open area Helvetica medium font 6-inch white reflective three letters.

· 6-inch reflective striping from edge-to-edge matching side height for continuous run around side edging.

· 1-inch red reflective striping shall be installed along the full length of rear passage door inside leading vertical edge.

Front Bumper

· Front Bumper 4-inch white Helvetica medium font reflective radio letters and number on front left upper outside solid section of bumper straight (horizontal).

Roof

· Roof letters and number shall be Aerial black Italic 100% 30 inches and shall go on the front of the buildup roof centered and be identified to match the radio numbers on the side of the ECT. The identifier shall be three letters and a number.

Fuel Tank(s)

· The contractor shall also install a green colored “DIESEL FUEL” adhesive backed label on the vehicle fuel tank(s). This decal shall be weather and fuel proof.

Diesel Exhaust Fluid Tank

· The contractor shall also install a blue colored “DEF” adhesive backed label on the vehicle DEF tank. This decal shall be weather and fuel proof.

image2.jpeg image3.jpeg image4.jpeg image5.jpeg image6.jpeg image7.jpeg image8.jpeg image9.jpeg image10.jpeg image11.jpeg image12.jpeg image13.jpeg image14.jpeg image15.jpeg image16.png image1.emf