Attachment 0007 PSD - 6x6 GTT.doc

Product Supporting Document (PSD) December 2020

GENERAL TRANSPORT TRUCK - MTV

The purpose of this PSD is to provide information in support of the specification.

Units: The data provided in the PSD is to be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Supporting documentation, see paragraphs 1(a)1, 1(a)2, 3(a)1, 3(b)1, 4(a)1, 4(b)1, 6(a)1, 6(b)1, 11(a)1, 12(a)1, 13(a), 17(a)1, and 18(a)1.

(b) Vehicle and major component commercial literature or specification sheets or any other information that would substantiate the information provided. If your commercial literature does not provide information relating to a particular question, you are required to provide a written explanation of your ability to meet that particular requirement with your written proposal.

(c) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications or redesigns.

Information Notes:

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb Weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and passenger - 175 lbs each).

(c) Gross Vehicle Weight (GVW) shown shall include curb weight of the vehicle, weight of the crew (350 lbs total), and the payload (assume evenly distributed).

(d) Gross Combination Weight (GCW) shall include the vehicle GVW and a weight of a fully loaded trailer coupled to the vehicle (Trailer GVW is 10,000 lbs with a vertical load on the pintle of 1,000 lbs).

GENERAL INFORMATION

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title

(c) Company Name

(d) Telephone/Fax Numbers

(e) E-mail address

(f) Mailing Address

(g) Company Website Comments

GENERAL TRANSPORT TRUCK - MTV

1. CONFIGURATION

(a) Is the vehicle a 6x6 General Transport Truck, Navistar HV series chassis, 2020 model year or later, with no more than 500 miles on the odometer when inspected? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A specification sheet(s) of the base chassis with all included options must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

2) SUPPORTING DOCUMENTATION: Dimensioned exterior drawings of the finished vehicle showing views of the top, sides, front and rear, troop seating configuration and headroom with soft cover and support structure installed must be provided (submit drawings in Adobe .pdf format). Dimensions shall include at a minimum the overall length, overall width with and without mirrors, overall height, ground clearance and wheelbase. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

2. RESERVED

3. EQUIPMENT

Is the vehicle equipped with (yes/no and briefly expand in comment section, as needed):

(a) All of the standard equipment typically found on this truck? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) listing all standard equipment found on the base truck must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

(b) A front-mounted vehicle self-recovery winch provided? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) describing the winch must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

4. RATINGS

(a) Vehicle Gross Vehicle Weight Rating (GVWR)? lbs

1) SUPPORTING DOCUMENTATION: A separate sheet showing calculations of vehicle curb weight (front and rear axles), fully loaded payload, and Gross Vehicle Weight (front and rear axles) must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

(b) Vehicle Gross Combination Weight Rating (GCWR)? lbs

1) SUPPORTING DOCUMENTATION: A separate sheet showing calculations of GCWR must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

5. RESERVED

6. ENGINE

(a) Can the vehicle be operated on high sulfur content diesel fuel (10,000 ppm or 1%)?

1) SUPPORTING DOCUMENTATION: Test data or Engine OEM concurrence must be provided. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

(b) Is the vehicle provided with an Exhaust Gas Recirculation (EGR) valve, Diesel Particulate Filter (DPF), Diesel oxidation Catalyst (DOC), Selective, Catalytic Reduction Catalyst (SCR) or any other emission control device?

1) SUPPORTING DOCUMENTATION: Engine specification sheet must be provided. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

7. RERSRVED, 8 RESERVED, 9. RESERVED, 10. RESERVED.

11. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Tires

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) of the tires must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

12. ELECTRICAL

(a) Is a dual voltage (12/24 volt) system with battery equalizer provided? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) of the battery equalizer must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

13. PERFORMANCE

(a) SUPPORTING DOCUMENTATION: A SCAAN or equivalent showing the GVW and GCW performance requirements of the specification must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

14. RESERVED

15. RESERVED

16. RESERVED

17. CARGO BODY

(a) Is the vehicle provided with a cargo body? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A specification sheet(s) of the cargo body listing all options and payload capacity must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

18. WEAPON MOUNT

(a) Is a vehicle provided with a ring and bearing type weapon mount for a 12.7 mm (50 caliber) machine gun capacity with continuous 360 degrees of rotation? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A specification sheet(s) and brochure of the weapon mount must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

19. RESERVED, 20. RESERVED, 21. RESERVED, 22. RESERVED.

SOURCE SELECTION SENSITIVE, SEE FAR 3.104