Attachment 0006 PSD - 4x4 GTT.doc

PRODUCT SUPPORTING DOCUMENT (PSD)

DECEMBER 2020

CARGO TRUCK 4x4, MTV The purpose of this PSD is to provide information in support of the specification.

GENERAL INFORMATION

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title

(c) Company Name

(d) Telephone/Fax Numbers

(e) E-mail address

(f) Mailing Address

(g) Company Website Units: The data provided in the PSD shall be in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Supporting documentation, see paragraphs 1(a)1, 1(a)2, 2(a)1, 3(a)1, 4(a)1, 4(b)1, 8(a)1, 9(a)1, 11(a)1, 12(a)1, and 13(a)

(b) Identification of all modifications/redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications/redesigns.

Information Notes:

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb weight shown shall be weight of truck offered, completely equipped (less only weight of payload). Weight distribution empty shall be based on curb weight.

(c) Gross Vehicle Weight (GVW) shown shall include vehicle’s curb weight, weight of the crew (350 pounds), and weight of a fully loaded platform body. The payload shall be assumed to be evenly distributed over the cargo space.

CARGO TRUCK 4x4, MTV

1. CONFIGURATION

(a) Is the vehicle a 4x4 truck chassis with a platform body suitable for hauling cargo, 2020 model year or later? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A specification sheet(s) of the base chassis with all included options must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

2) SUPPORTING DOCUMENTATION: Dimensioned exterior drawings of the finished vehicle showing views of the top, sides, front and rear, troop seating configuration and headroom with soft cover and support structure installed must be provided (submit drawings in Adobe .pdf format). Drawings listed in the previous sentence should be two sets; one with soft cover and troop seats installed and one with those items not shown. Dimensions shall include at a minimum the overall length, overall width with and without mirrors, overall height, ground clearance and wheelbase. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

2. EQUIPMENT

Is the vehicle equipped with (yes/no and briefly expand in comment section, as needed)?

(a) All of the standard equipment typically found on this truck? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) listing all standard equipment found on the base truck must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

3. RATINGS

(a) Vehicle Gross Vehicle Weight Rating (GVWR)? lbs

1) SUPPORTING DOCUMENTATION: A separate sheet showing calculations of vehicle curb weight (front and rear axle), fully loaded payload, and Gross Vehicle Weight (front and rear axles) must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

4. ENGINE

(a) Can the vehicle be operated on high sulfur content diesel fuel (10,000 ppm or 1%)?

1) SUPPORTING DOCUMENTATION: Test data or Engine OEM concurrence must be provided. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

(b) Is the vehicle provided with an Exhaust Gas Recirculation (EGR) valve, Diesel Particulate Filter (DPF), Diesel oxidation Catalyst (DOC), Selective, Catalytic Reduction Catalyst (SCR) or any other emission control device?

1) SUPPORTING DOCUMENTATION: Engine specification sheet must be provided. State where this is provided in your proposal (e.g. page number, paragraph, etc.).

Comments

5. RESERVED

6. RESERVED

7. RESERVED

8. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Tires

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) of the tires must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

9. ELECTRICAL SYSTEM

(a) Is a dual voltage (12/24 volt) system with battery equalizer provided? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION: A brochure or specification sheet(s) of the battery equalizer must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

10. RESERVED

11. CAB

(a) Is the driver’s air suspension seat provided? FORMDROPDOWN , if yes:

1) SUPPORTING DOCUMENTATION: A specification sheet(s) or brochure of the air suspension seat must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

12. PLATFORM BODY

(a) Is the vehicle provided with a platform body? FORMDROPDOWN ; If yes:

1) SUPPORTING DOCUMENTATION: A specification sheet(s) of the platform body listing all options and payload capacity must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

13. PERFORMANCE

(a) SUPPORTING DOCUMENTATION: A SCAAN or equivalent showing the GVW performance requirements of the specification must be provided. State where this information is provided in your proposal (e.g. page number, paragraph, etc.)

Comments

14. RESERVED

15. RESERVED

SOURCE SELECTION SENSITIVE, SEE FAR 3.104