A04_-_Statement_of_Work_140P1525Q0038.pdf

General

1. Warranty: Vendor will provide minimum one year warranty for wiring/installation

2. Build time: Vehicle should be completed within fifteen business days after receiving the new vehicle.

3. Vehicle Returns: Upon decommissioning the one old Ford F150, the vendor will facilitate their return to the GSA Metro Phoenix Auto Auction, located at the address listed below. Adrian Salcedo is the point of contact at the Auto Auction. **The vendor must schedule an appointment for the vehicle return ahead in advance.**

GSA Metro Phoenix Auto Auction 2475 S. 59th Ave Phoenix AZ 85043

POC: Adrian Salcedo

(602) 567-3364

Power Supply/wiring

1. Timer: timer should turn all emergency equipment off after 30 minutes

2. Dome light in cab should be on constant 12v not timer/ign

3. Fuses will be labeled, or a diagram will be provided for easy replacement

4. Radio head units, remote siren power supplies, cell boosters will be mounted in a uniform fashion and serial numbers are accessible where applicable (i.e., passenger side partition, rear cargo screen, etc.)

Siren Controls/functions

1. Siren slide switch controls:

Stage 1: All rear facing lights activate S60 Stage 2: Front, side, and rear lights (to include wig wags/strobes/white lights) activate S60 Stage 3: All Front and rear lights plus siren activate in faster pattern

2. Siren buttons will be labeled as to their function (minus gunlock). The gunlock will be the button in the lower right corner and will be labeled as “AUX”. Gunlock will activate by pressing GL then “cruise”

3. Park kill and horn ring will be activated on siren controllers

Consoles

1. Consoles will be set up in a uniform fashion and any equipment not provided by NPS will be furnished by vendor through a plus/over (i.e., mic clips, mounts, brackets, faceplates)

2. If equipped from factory and not installed, USB/AUX/12v outlets will be added to a faceplate on the console

3. Factory-supplied 110v inverter harness will be installed and routed to console

Lighting

1. “Black out” function (controlled by button on siren) will disconnect tail/reverse/marker lights/courtesy lights and dim dash lights (controlled through siren controller)

Radios

1. Mobile radios will have rebroadcast over PA feature enabled through PF200

2. APX Radios will have proper antennas installed

Marking

1. On “ghost marked” vehicles, roof ID’s will be done in 12” black reflective characters

2. High-visibility Chevrons will be placed on rear of vehicle

F-150 Responder (QTY 2)

GSA turn in

• Strip out equipment from old vehicles

• Turn in and swap out for new GSA vehicles

BUILDS

Front:

1. 2 Brookings LED lights in grille

2. IR LED pods driving light reuse

3. Multifunction LED light bar bottom of grille reuse

4. One siren speaker mounted on bottom of push bumper(new)

5. Headlight/taillight flasher (activated through vehicle harness)

6. 2 Brookings R/B mounted in low in factory fog/outside edge of bumper(new)

7. 2 Brookings Mirror lights (wired white to alley, white strobe on C3) (new)

Inside front:

1. Power distribution unit (Vendor Provided)

2. Brookings visor LED lightbar (Vendor Provided)

3. Jotto floor brackets (Vendor Provided)

4. Radar unit mounted to industry standard reuse

5. Radar antenna mounted to industry standard reuse

6. 12” Jotto Console (see picture for setup)

a. Federal Signal Pathfinder with expansion module (new)

b. Radar Control reuse

c. Wiboost Fleet Cell Phone Booster(new)

d. Tail light/running light/brake light/dash light/interior light kill switch

(black out switch)

e. 3 hole 12v outlet mounted on console reuse

f. Streamlight Stinger DS flashlight mounted right side reuse

7. Cupholders reuse

8. Locking console storage reuse

9. Dome light (Vendor Provided)

10. APX 8500 Motorola Radio (new)

11. Gunlocks double partition mounted (new)

Inside Rear:

1. Decked Cargo drawers reuse

2. Setina Prisoner Partition reuse

3. radar antenna mounted industry spec reuse

4. Hatch dome light (Vendor Provided)

5. Brookings LED in B or C pillar (new)

Rear:

1. White Camper shell with bins in sides (Vendor Provided)

2. Headlight/taillight flasher (wired through harness)

3. 4 Brooking LED’s or light stick (single color) mounted in rear glass (Vendor

Provided)

4. 2 Brooking LEDs mounted under rear taillights/ license plate(new)

5. 2 Brooking LED LEDs mounted on tailgate (new)

Marking:

1. NPS Ghost Graphics package(new)

2. NPS (last three of vehicle plate) on roof (see pic) (Vendor Provided)

(new)= NPS provided (Vendor Provided)=provided by upfitter Reuse= reuse from turn in vehicle