Att_17_SWIFT_FWSG_FlashScan_0001.pdf

DN-60820:C • 9/30/2015 — Page 1 of 3

SWIFT®

FWSG FlashScan® Wireless Gateway

Intelligent Wireless Devices

DN-60820:C

FWSG FlashScan Wireless Gateway

General The SWIFT® Wireless System can be applied in many situa-tions that are problematic for traditional wired devices. In cases where areas of a building are difficult or impossible to wire, visually sensitive, or have restricted access, SWIFT wire-less sensors provide an efficient, reliable solution.

SWIFT wireless devices communicate via a proprietary wire-less mesh protocol to communicate with a NOTIFER® ONYX® fire alarm system by means of a SWIFT Wireless Gateway.

The SWIFT Gateway connects to the SLC loop of an NFS2- 3030, NFS2-640, or NFS-320 panel (running version 24 firm-ware or higher) using FlashScan® protocol. New type IDs for wireless devices are supported that allow the FACP to display all events such as alarms and trouble indications, as well as unique trouble conditions required for wireless devices. This capability eliminates the need for a supplementary annunciator for wireless event messages.

Wireless devices in a SWIFT network develop "parent-child" communication links with other devices in the mesh, so that a message originating from a remote device "hops" to the clos-est parent device, and then to successive parent devices until the message reaches gateway. Alternate paths are also identi-fied and supervised by the SWIFT protocol providing approved Class A wireless communication. If a device does not have an established communication path with adequate signal strength, an additional device such as a wireless module may be installed in between so that it will act as a repeater.

A SWIFT Gateway system supports up to 50 devices: 1 SWIFT Gateway and up to 49 wireless detectors and monitor modules. The Gateway assumes one SLC address (module), and each wireless device assumes one module or detector address. The maximum number of gateways on a system is limited by the number of available SLC addresses on the FACP, or a maximum of 4 gateways within common wireless range.

The SWIFT system has been designed so that it can be installed using only typical hand tools and magnets. However, the SWIFT Tools PC utility provides many benefits that can enhance the process of performing a site evaluation (Site Sur-vey), installing a system (Mesh Configuration), or extracting detailed information from the system (Diagnostics). The utility runs on a Windows® laptop, and uses a USB radio antenna (W-USB) inserted into a USB slot to communicate with wire-less devices within range of the PC. Once devices have formed a mesh, SWIFT Tools can provide current information on all devices in the mesh as long as the PC is within range of the SWIFT Gateway.

The result is a fire system that combines both wired and wire-less detection and presents all event information at the panel and/or network displays, when used.

Features

• SWIFT wireless mesh protocol specifically for fire and life safety systems:

– Operates in 902-928 MHz frequency.

– Patented cascading-wave mesh operation provides a verification of redundant communication paths that has been approved for Class A.

– In the event that a communication path is interrupted at any point by a change in the radio environment, the SWIFT mesh system will use the redundant or backup communication path.

– In the event that any links cannot be established with suf-ficient signal strength, any SWIFT device can be added to act as a repeater, eliminating the need for wired repeat-ers. A wireless monitor module is recommended for this function, as modules are not subject to spacing require-ments.

• Each SWIFT gateway system support up to 50 devices: 1 wireless gateway and up to 49 SWIFT devices.

• Multiple SWIFT wireless mesh networks can be installed on the same fire alarm control panel, or on multiple panels in the same area.

• Up to 4 wireless networks can be installed with overlapping radio network coverage.

• Site Survey feature allows for an evaluation of a site before the installation, including a series of point-to-point commu-nication tests and a background scan for radio interference.

• SWIFT wireless devices use a standard “code wheel” mechanism for setting the SLC address.

• SWIFT wireless devices use (4) CR-123A lithium batteries (Panasonic CR123A or Duracell DL123A) which are UL listed for a battery life of 2 years.

SWIFT Tools SWIFT Tools is a Windows PC-based utility that is used for site evaluation, system configuration, and diagnostics. The SWIFT Tools program is used with the W-USB adapter to com-municate with wireless devices that are not joined in a net-work, or with one or more wireless gateways and all devices that have formed a network with each gateway. A graphic rep-resentation of the wireless network provides important system data in an effective format, including communication links, sig-nal strength, battery voltage, and more.

Page 2 of 3 — DN-60820:C • 9/30/2015

Tool-less operation is supported, allowing you to perform site evaluation and system configuration and installation can be accomplished without using SWIFT Tools when necessary.

Multi-colored LEDs on SWIFT devices provide feedback for interactions. At any point, only one instance of SWIFT Tools can run on a laptop or PC.

SWIFT Tools has the following utilities:

• Site Survey

• Create Mesh Network

• Diagnostics

SWIFT Tools works in a wireless environment with the FWSG and devices within a range of approximately 20 feet.

SWIFT Tools is designed for systems running Microsoft Win-dows.

MINIMUM SYSTEM REQUIREMENTS

Operating System: Windows XP Professional (SP3), Vista, Windows 7, and Windows 8 (32 bit and 64 bit).

Hard Drive: 20 GB hard drive space with minimum 1GB free space on hard disk.

RAM: Minimum 512MB RAM.

Processor speed: 1GHz minimum (2.4 GHz recommended) Processor, 512K Cache.

SWIFT Components and Ordering Infor-mation

• FWSG: FlashScanWireless SWIFT Gateway - 1 SWIFT

Gateway is required for each wireless mesh, and supports up to 49 SWIFT detectors or modules. Connects to the SLC loop of a compatible panel using FlashScan protocol.

Power may be supplied by the SLC circuit or via an optional 24VDC input.

NOTE: Use of the 24VDC input may be more convenient for ser-vice as it allows for powering down a gateway without shutting down an SLC loop.

• FWD-200P: FlashScan intelligent, wireless photo detector.

Requires one B210W base for installation. Requires (4) CR-123A batteries (included).

• FWD-200ACCLIMATE: FlashScan intelligent wireless Acclimate® heat and photo detector using combined heat and smoke sensor information and the ability to automati-cally adjust sensitivity based on ambient changes in the environment. Requires one B210W base for installation.

Requires (4) CR-123A batteries (included).

• FWH-200ROR135: FlashScan intelligent wireless rate of rise (135°) heat detector. Requires one B210W base for installation. Requires (4) CR-123A batteries (included).

• FWH-200FIX135: FlashScan intelligent wireless fixed-tem-perature (135°) heat detector. Requires one B210W base for installation. Requires (4) CR-123A batteries (included).

• FW-MM: FlashScan wireless monitor module. Used to monitor devices with mechanical contact actuation.

Includes a special cover with a tamper magnet built in. Rec-ommended for installation in a SMB500 box (ordered sepa-rately) rather than a metal backbox for best performance.

Ships with 4 Panasonic CR123A or 4 Duracell DL123A bat-teries. (See data sheet for more information).

• FW-RM: Wireless relay module for use with the FWSG wireless gateway. Includes a special cover with a tamper mag-net built in. Recommended for installation in an SMB500 box (ordered separately) rather than a metal back-box for best performance. Ships with 4 Panasonic CR123A or 4 Duracell DL123A batteries.

• SMB500: Optional surface-mount backbox.

• B210W: Detector base used for wireless detectors.

Includes a built-in magnet so that wireless devices can establish installed and tampered states.

• FW-PTOOL: SWIFT Tools programming and diagnostic util-ity. Free download from notifier.esd.com. For installation on a (typically laptop) PC running an approved version of Win-dows (See Minimum System Requirements for SWIFT Tools). Requires the W-USB radio/antenna dongle for com-munication with SWIFT Wireless devices.

Example of SWIFT Tools’ Diagnostic Utility

Page 3 of 3 — DN-60820:C • 9/30/2015

Acclimate® Plus, FlashScan®, NOTIFIER®, ONYX® are registered trademarks of and SWIFT™ is a trademark of Honeywell International Inc.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

©2015 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.

www.notifier.com

NOTE: SWIFT Tools is intended for use with NOTIFIER branded products and can also be used with Fire•Lite branded wireless products. It will not work with other brands.

• W-USB: Wireless USB radio/antenna dongle that plugs into the USB port of a PC running SWIFT Tools. The W-USB provides a communication link with SWIFT Wireless devices that are within approximately 20 feet and have not formed a mesh. Alternately, when the devices have formed a mesh, bringing the PC/W-USB within range (20 ft.) of the gateway for that mesh will allow SWIFT Tools to acquire information on all devices in that mesh, including point-to-point signal strength for all links.

Agency Listings and Approvals The listings and approvals below apply to the FWSG. In some cases, certain modules may not be listed by certain approval agencies or listing may be in process. Consult factory for latest listing status.

UL Listed: S635

CSFM: 7300-0028:0272

NYC Fire Dept: COA #6180

FM Approved

FCC ID: PV3WFSGW

IC ID: 12252A-WFSGW

Standards and Codes The SWIFT Wireless System complies with the following UL Standards and with NFPA 72 Fire Alarm system requirements.

UL 864

UL 268

FACP

SLC

wired SLC devices

FWSG

Gateway

SWIFT

Tools USB adapter wireless mesh network

SWIFT Network

DN-60832:C • 9/30/2015 — Page 1 of 2

SWIFT®

Intelligent Wireless Detectors

Intelligent Detectors

DN-60832:C

Intelligent Wireless Detector with B210W base

S w ift D et ec to r

B ba se .jp g

General SWIFT® wireless detectors are intelligent (addressable) detectors which provide secure, reliable communication to the Fire Alarm Control Panel (FACP) across a Class A mesh network. Wireless detectors create an opportunity for appli-cations where it is costly (concrete walls/ceilings, buried wires), obtrusive (surface mount conduit), or possibly dan-gerous (asbestos) to use traditional wired devices. In addi-tion, both wired and wireless devices can be present on the same FACP providing an integrated wired-wireless solution for increased installation potential.

The SWIFT detection line includes a photoelectric, Accli-mate®, standard fixed heat, and rate-of-rise heat detectors.

The photoelectric detectors transmit a digital representation of smoke density through a wireless mesh to a gateway and on to a FACP. The Acclimate detectors combine a photoelec-tric chamber and a 135°F fixed temperature heat detector.

Acclimate can also transmit an alarm signal due to heat per UL 521. The fixed heat detector and rate-of-rise detectors uti-lize sensors designed for open area protection with 50 foot spacing capability as approved by UL 521.

All sensors offer addressable code wheels and two LEDs.

The LEDs are controlled by the panels. Operation modes include red, green, and amber colors with various solid or blink patterns.

The mesh network within the SWIFT system creates a child-parent relationship between the devices so that each device has two parents providing a second path for communications on every device. If one device can no longer operate for any reason, the rest of the devices can still communicate with each other, directly or through one or more intermediate devices.

The SWIFT system also engages frequency hopping to pre-vent system interference whether intentional or accidental.

Features

• Wireless installation

• Class A mesh network

• Addressable code wheels

• Commercial applications

• UL 268 listed

• Frequency hopping

• Bi-directional communications

Specifications

PHYSICAL / OPERATING SPECIFICATIONS

Height: 2.4 inches (61 mm) installed in B210W base

Diameter: 6.0 inches (152mm) installed in B210W base

Device Weight (includes 4 batteries): 9.2 oz (261 g) installed in B210W base

Operating Temperature Range: Photo: 32°F to 120°F (0°C to 49°C); Acclimate with Heat: 32°F to 100°F (0°C to 38°C)

Air Velocity: Acclimate with Heat: 0 to 4,000 fpm (0 to 20 m/ sec)

Operating Humidity Range: 10% to 93% non-condensing

Thermal Ratings: Fixed Temperate Set Point: 135°F (57°C); Rate-of-Rise Detection: 15°F/min (8.3°C/min)

ELECTRICAL SPECIFICATIONS

Maximum Operating Voltage: 3.3 VDC

Maximum Standby Current: 210µA @ 3.3 VDC (one com-munication every 23.9 seconds with LED blink enabled)

Maximum Alarm Current (LED on): 5 mA @ 3.3 VDC (LED on)

Radio Frequency Range: 902-928 MHz

BATTERY SPECIFICATIONS

Battery Type: 4 Panasonic CR123A or 4 Duracell DL 123A

Battery Life: 2 years

Battery Replacement: Upon BATTERY LOW or BAT LOW display and/or during annual maintenance

Agency Listings and Approvals Each device complies with part 15 of the FCC rules meaning operation is subject to two conditions.

1) The device may not cause harmful interference and 2) The device must accept any interference received including inter-ference that may cause undesired operation.

The listings and approvals below apply to the basic intelligent wireless detector. In some cases, certain modules may not be listed by certain approval agencies or listing may be in process. Consult factory for latest listing status.

UL Listed: S635

CSFM: 7272-0028:0271, 7254-0028:0270

FM Approved

FCC ID: AUBWFSSD

IC ID: 573X-WFSSD

Page 2 of 2 — DN-60832:C • 9/30/2015

Acclimate® Plus, FlashScan®, NOTIFIER®, and SWIFT® are registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

©2015 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.

www.notifier.com

Standards and Codes The SWIFT Wireless Intelligent Detectors comply with the following UL Standards and with NFPA 72 Fire Alarm System requirements.

UL 864

UL 268

Ordering Information FWD-200P: Wireless photoelectric smoke detector for use with the FWSG wireless gateway

FWD-200ACCLIMATE: Wireless Acclimate detector for use with the FWSG wireless gateway

FWH-200FIX135: Wireless fixed-temperature (135° F) heat detector for use with the FWSG wireless gateway

FWH-200ROR135: Wireless rate-of-rise (135° F) heat detector for use with the FWSG wireless gateway

FWSG: FlashScan® Wireless Gateway.

B210W: 6” wireless mounting base.

W-USB: Software interface (via USB port) for computers running the SWIFT Tools programming utility.