CFR 001 Intersleek 731.pdf

A two pack, silicone elastomer tie coat.PRODUCT DESCRIPTION

To promote adhesion between the specified priming system and the Intersleek 757 finish coat.

For use at Newbuilding or Maintenance & Repair.

INTENDED USES

BXA730-Light Pink, BXA732-Red

63% ±2% (ASTM D2697-86)

4 mils dry (6.4 mils wet)

253 ft²/US gal at 4 mils dft, allow appropriate loss factors

Airless Spray, Brush

PRODUCT INFORMATION

Volume Solids

Typical Film Thickness

Theoretical Coverage

Method of Application

Finish/Sheen Low-Gloss

Part B (Curing Agent) BXA731

Mix Ratio 1 volume(s) Part A to 1 volume(s) Part B

Flash Point Part A 82°F; Part B 86°F; Mixed 83°F (Setaflash) (ASTM D-3278)

Induction Period Not required

Overcoating Data - see limitations Substrate Temperature

Color

Drying Information 50°F 59°F 77°F 95°F

Touch Dry [ASTM D1640 7.5.1] 150 mins 140 mins 90 mins 30 mins

Hard Dry [ASTM D1640 7.7] 6 hrs 5 hrs 4 hrs 3 hrs

Pot Life 3 hrs 3 hrs 3 hrs 3 hrs

Overcoated By

50°F 59°F 77°F 95°F

Min Max Min Max Min Max Min Max

Intersleek 757 6 hrs 7 days 5 hrs 7 days 4 hrs 7 days 3 hrs 7 days

Intersleek 970 6 hrs 7 days 5 hrs 7 days 4 hrs 7 days 3 hrs 7 days

REGULATORY DATA VOC

Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances.

325 g/lt (2.71 lb/US gal) as supplied (EPA Method 24)

MIL SPEC MIL-PRF-24647D, Type III, CL1, 2 & 3, Gr A, Applications 1 & 2

Intersleek 731 Elastomeric Tie Coat

Ref:729

Issue Date:3/6/2012

Marine Coatings

Intersleek 731 Elastomeric Tie Coat

Consult your International Paint representative for the system best suited for the surfaces to be protected.SYSTEMS AND

COMPATIBILITY

Use in accordance with the standard Worldwide Marine Specifications.

All surfaces to be coated should be clean, dry and free from contamination.

High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

SURFACE PREPARATIONS

Intersleek 731 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intersleek 731 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Intersleek 731

Consult your International Paint representative for specific recommendations.

NOTE

For use in Marine situations in North America, the following surface preparation standards can be used:

SSPC-SP10 in place of Sa2½ (ISO 8501-1:2007)

Ref:729

Material is supplied in two containers as a unit. Always mix a complete unit in the portions supplied. Once the unit has been mixed it must be used within the working pot life specified.

(1) Agitate Base (Part A) with power agitator.

(2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.

Once the unit has been mixed, it must be used within the working pot life specified.

Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Not suitable.

DO NOT THIN BEYOND YOUR STATE'S COMPLIANCY. Material is supplied at spray viscosity and normally does not need thinning. If thinning is necessary, thin up to a maximum of 4 ounces/gal. with International GTA007 Thinner.

International GTA007

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

Recommended Tip Range 15-21 thou (0.38-0.53 mm) Total output fluid pressure at spray tip not less than 3000 psi (211 kg/cm²)

Application by conventional spray is not recommended.

APPLICATION

Mixing

Airless Spray

Conventional Spray

Brush

Roller

Thinner

Cleaner

Welding

Apply by airless spray. Application by brush or roller will require more than one coat and is suggested for small areas only of stripe coating. Strain material through a minimum 60 mesh screen before application. Apply at 6.4 mils wet which will yield 4.0 mils dry film thickness. Consult the following equipment recommendations or utilize suitable equal.

Work Stoppages and Cleanup Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA007. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.

Clean all equipment immediately after use with International GTA007. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations.

All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

EMERGENCY CONTACT NUMBERS:

USA/Canada - Medical Advisory Number 1-800-854-6813 Europe - Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191 R.O.W. - Contact Regional Office

SAFETY

Ref:729

Care should be taken to avoid overspray onto other coated areas.

All equipment must be thoroughly clean prior to use, and before re-use with other materials, to prevent contamination. Liquid cleaners for Intersleek 731 must not be allowed to contaminate other paints.

Apply in good weather when air and surface temperatures are above 50°F and relative humidity is above 40%.

Surface temperature must be at least 5°F above dew point. For optimum application properties, bring material to 70- 80 °F prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage between 40 and 100°F.

Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations.

Technical and application data herein is for the purpose of establishing a general guideline of the coating and proper coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results actually found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

LIMITATIONS

UNIT SIZE Unit Size Part A Part B

Vol Pack Vol Pack

2 US gal 1 US gal 2 US gal 1 US gal 1 US gal

UNIT SHIPPING WEIGHT Unit Size Unit Weight

2 US gal 23.5 lb

Shelf Life 12 months minimum at 77°F, 6 months minimum at 104°F. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.

STORAGE

Consult International Paint.WORLDWIDE AVAILABILITY

The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to using the product.

This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this document. Should there be any discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the version on the website will take precedence.

IMPORTANT NOTE

and product names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel.

© AkzoNobel, 2012 www.international-marine.com

Ref:729

Issue Date:3/6/2012 http://www.international-marine.com