X10 Drone Dock Manual_Installation and Specifications.pdf

Skydio Dock for X10 Site Readiness Manual

Site Readiness Manual

Dock Specifications

Technical Specifications

Weights and Dimensions

External Radio Specifications

Technical Specifications

Weights and Dimensions

Site Preparation

Dock Power Requirements

External Radio Power Requirements

Wiring Configuration

Ethernet Cable Requirements

Computer System Requirements

Installation Requirements

Transport and Delivery

Dock Installation Requirements

External Radio Installation Requirements

Multiple Docks (Hive)

Appendixes

Corrosion Guidance

Safety Information

Revision History

Site Readiness Manual This document explains installation requirements, technical specifications, network and power provisioning, and flight‑zone design for one or more Skydio Dock for X10s.

NOTICE

Follow official documentation and updates.

Failure to follow any instructions or recommendations in Skydio documentation may void the Skydio Limited Warranty or other terms and conditions.

Please read all documentation provided with the Skydio Dock for X10, including but not limited to the Doc for X10 Safety Guidelines in the Safety and Operating Guide: www.skydio.com/safety.

© 2026 Skydio, Inc. All rights reserved. Proprietary. Printed copies are uncontrolled.

http://www.skydio.com/safety

Skydio Dock for X10 Site Readiness Manual | Page 4

Dock for X10 Specifications

Technical Specifications This section contains technical specifications for the Dock for X10.

Category Specification / Requirement

Launch Time 20 Seconds

Battery Charge Time 15% to 95% within 35 minutes at 77°F (25°C)

Cooling or heating will increase overall charge time to max of 73 minutes

Power Input 100 V to 240 V (200 V to 240 V required below 32°F (0°C)).

50 to 60 Hz

2200W at peak load

20A breaker for 200 V to 240 V

For more information, see Peak Power by Dock State (on page 14)

Power Load

1200W for operations above 32°F (0°C)

15A breaker for 100V-120V

Input/Output 2x PoE (30 W, 48 V)

1x USB 3.0 (5 W, 5 V)

Onboard Storage 512 GB (Non-removable, for media sync purposes only)

Service Life 5 years with regular service conducted annually

WARNING:

Ice accumulation when operating below 32°F (0°C) without a 200V-240V power supply. When operating below 32°F (0°C) without a 200V-240V power supply, Dock Heater functionality will be unavailable. Ice accumulation can result in degraded performance, crashes, or loss of the aircraft. For operation below 32°F (0°C), a 200V-240V power supply from a dedicated 20A breaker must be provided to enable Dock Heater functionality. Provide a 100V-120V power supply from a dedicated 15A breaker for operation in temperatures from 32°F (0°C) to 122°F (50°C).

Skydio Dock for X10 Site Readiness Manual | Page 5

Operating Limits

Category Specification / Requirement

Launch / Land Winds Up to 12 m/s (28 mph / 45 km/h)

Standby Wind Rating Bolted to Permanent Structure: Up to 160 mph (257 km/h)

Note:

For bolting guidance information, see Dock Installation Requirements (on page 22)

Skydio Dock Feet Installed: 80 mph (128 km/h)

Non-Bolted: 40 mph (64.4 km/h)

Operational Temperature

-4° to 122° F (-20° to 50° C)

Standby/Storage Temperature

-40° to 140° F (-40° to 60° C)

Ingress Protection (Roof Open)

IPX5

Ingress Protection (Roof Closed)

IPX6

Corrosion Resistance Designed to operate in humid environments, outside of direct saltwater splash zones.

Rain and Snow Limitations

Operational Capability*:

• 0.25 in/hr (light-moderate)

• Standby: 4.0 in/hr (Heavy)

*Limited by Dock for X10.

Skydio Dock for X10 Site Readiness Manual | Page 6

Weights and Dimensions

Weights

Category Specification / Requirement

Dock Roof 36 lb (16.3 kg)

Dock Base 143 lb (64.9 kg)

Dock Stand 53 lb (24.0 kg)

Fully Assembled 240 lb (108.9 kg)

Total Shipping Weight 300 lb (136.1 kg)

WARNING:

Transportation pallet tip hazard. Do not remove the Dock from its shipping pallet until it has reached the designated final installation location. While operating lift equipment, wear appropriate PPE.

Dimensions

Category Specification / Requirement

Height (Front View - Closed Roof) 55.5 in (141.0 cm)

Height (Front View - Open Roof Maximum)

37.6 in (95.5 cm)

Height (Side View - Dock Base) 31.3 in (79.5 cm)

Height (Side View - Dock Stand) 24.1 in (61.2 cm)

Width (Front View - Closed Roof) 37.7 in (95.8 cm)

Width (Front View - Open Roof) 40.5 in (102.9 cm)

Depth (Side View – Closed Roof) 34.1 in (86.6 cm)

Depth (Side View – Open Roof) 45.9 in (116.6 cm)

Depth (Side View - Maximum) 48.9 in (124.2 cm)

Doorway (Minimum) 29.7 in (75.4 cm)

Skydio Dock for X10 Site Readiness Manual | Page 7

Height / Width Depth / Base Height / Stand Height

Entryway Minimum Width - Roof Open

Depth - Roof Open Maximum Depth / Height - Roof Open

Skydio Dock for X10 Site Readiness Manual | Page 8

Materials

The Dock for X10 is composed of the following materials:

• Exterior Plastic: UL F1 rated* coating meets AAMA 2604 compliance for UV Resistance.

• Exterior Metals: Coated with Tiger Drylac Series 138* coating.

Note:

This coating is AAMA 2604 compliant for UV Resistance

*All materials and components are subject to change

Skydio Dock for X10 Site Readiness Manual | Page 9

External Radio Specifications

Technical Specifications WNC Radio Antenna

Type Specification / Requirement

Low Voltage Power Nominal: 11 to 13 W

USB-C: 5 V / 3 A, 9 V / 3 A, 12 V / 3 A, 15 V / 3 A, 20 V / 3 A

PoE: IEEE 802.3af

Power Input PoE from Skydio Dock or by Customer network.

Minimum: IEEE 802.3af

Power Load 11 to 13 W

Power draw will increase with increasing cable lengths

Input/Output 1x Ethernet, 1x USB-C 3.0

Operating Frequency Connect SL: 2400 to 2483.5 MHz and 5150 to 5850 MHz

Service Life 5 years of continual service with Dock

2 years when human-carried

ADS-B In Included

Skydio Dock for X10 Site Readiness Manual | Page 10

Type Specification / Requirement

GNSS GPS + Galileo + GLONASS + BeiDou

Operating Limits

Type Specification / Requirement

Wind Resistance* Up to 130 mph (209 km/h)

Operational Temperature -4° to 122°F (-20° to 50°C)

Storage Temperature -40° to 176°F (-40° to 80°C)

Ingress Protection IP55

Corrosion Resistance Designed to operate in humid environments, outside of direct saltwater splash zone

* Measures the wind speed at which the External Radio and bracket will remain on the pole they are mounted to.

This specification does not indicate the wind resistance of the pole itself.

Skydio Dock for X10 Site Readiness Manual | Page 11

Weights and Dimensions

Weights

Category Specification / Requirement

Total Weight 2.65 lbs (1.2 kg)

Dimensions

Category Specification / Requirement

Height (Antenna to Antenna) 19.7 in (50.0 cm)

Width (Pine Dual Band) 9.4 in (23.9 cm)

Depth (Pine Dual Band to Rear Bracket) 9.3 in (23.6 cm)

Skydio Dock for X10 Site Readiness Manual | Page 12

Site Preparation

Dock Power Requirements

Power Connection Options

The Dock for X10 may be powered with either a 100V-120V connection or a 200V-240V connection. To ensure the Dock is able to operate in below freezing conditions, use a 200V-240V connection.

WARNING:

Ice accumulation when operating below 32°F (0°C) without a 200V-240V power supply. When operating below 32°F (0°C) without a 200V-240V power supply, Dock Heater functionality will be unavailable. Ice accumulation can result in degraded performance, crashes, or loss of the aircraft. For operation below 32°F (0°C), a 200V-240V power supply from a dedicated 20A breaker must be provided to enable Dock Heater functionality. Provide a 100V-120V power supply from a dedicated 15A breaker for operation in temperatures from 32°F (0°C) to 122°F (50°C).

Disconnect Accessibility:

Provide a local switched disconnect on the roof, accessible to both Skydio and Customer personnel.

DANGER:

Electrical hazard. Exposure to energized components can result in serious injury or death. Follow local/site specific lockout/tagout procedures for de-energizing the Dock and removing electrical hazards. Ensure the work area is clear of unnecessary personnel. If necessary, restrict access to the area.

Before performing service on the unit, do the following:

• Engage the Dock E-Stop button.

• Turn the Dock OFF.

• Disconnect the Dock from the AC power supply.

• Disconnect all external data and power cables from the Dock.

• Complete required lockout/tagout procedures per site requirements.

Surge Protection:

To better protect the dock, it is recommended to use surge protection rated 40 kA or 4 kV.

Skydio Dock for X10 Site Readiness Manual | Page 13

Power for Each Dock Type Specification / Requirement

Power Input 100 V to 240 V (200 V to 240 V required below 32°F (0°C)).

50 to 60 Hz

2200W at peak load

20A breaker for 200 V to 240 V

Power Load

1200W for operations above 32°F (0°C)

15A breaker for 100V-120V

Input/Output 2x PoE (30 W, 48 V)

1x USB 3.0 (5 W, 5 V)

Skydio Dock for X10 Site Readiness Manual | Page 14

Peak Power by Dock State Hot Room Temperature Cold Peak Voltage

(VAC): 100 V

Cold Peak Voltage

(VAC): 240 V

Device / Status

140 °F / 60 °C 75 °F / 23.8 °C -4° F / -20 °C -4° F /-20 °C

Dock - Not Charging 550 W 400 W 1300 W 1300 W

Dock - Charging 850 W 700 W 1430 W 1600 W

Dock - Super Charging 1000 W 850 W 1430 W 1750 W

Dock - Moving 1200 W 1000 W 1120 W 1300 W

External Radio Power Requirements Type Specification / Requirement

Power Nominal: 11 to 13 W

USB-C: 5 V / 3 A, 9 V / 3 A, 12 V / 3 A, 15 V / 3 A, 20 V / 3 A

PoE: IEEE 802.3af

Power Input PoE from Skydio Dock or by Customer network.

Minimum: IEEE 802.3af

Power Load 11 to 13 W

Power draw will increase with increasing cable lengths

Skydio Dock for X10 Site Readiness Manual | Page 15

Wiring Configuration

Hardwired and Conduit Requirements

DANGER:

Electrical hazard. Exposure to energized components can result in serious injury or death. Follow local/site specific lockout/tagout procedures for de-energizing the Dock and removing electrical hazards. Ensure the work area is clear of unnecessary personnel. If necessary, restrict access to the area.

Before performing service on the unit, do the following:

• Engage the Dock E-Stop button.

• Turn the Dock OFF.

• Disconnect the Dock from the AC power supply.

• Disconnect all external data and power cables from the Dock.

• Complete required lockout/tagout procedures per site requirements.

WARNING:

Ice accumulation when operating below 32°F (0°C) without a 200V-240V power supply. When operating below 32°F (0°C) without a 200V-240V power supply, Dock Heater functionality will be unavailable. Ice accumulation can result in degraded performance, crashes, or loss of the aircraft. For operation below 32°F (0°C), a 200V-240V power supply from a dedicated 20A breaker must be provided to enable Dock Heater functionality. Provide a 100V-120V power supply from a dedicated 15A breaker for operation in temperatures from 32°F (0°C) to 122°F (50°C).

The following applies from the perspective of the Drone:

• Low voltage data is routed to the left side of the Dock.

• High Voltage AC power is routed to the right side of the Dock.

Skydio Dock for X10 Site Readiness Manual | Page 16

The following hardwire and conduit requirements apply to Dock installation:

• There must be 1x circuit per Dock.

• A manual disconnect must be accessible to a Skydio Authorized Technician and placed within line of sight of the Skydio Dock.

• For 200 V to 240 V: 12 AWG setup required for cold weather (L1, L2, G)

• For 100 V to 120 V: 12 AWG setup (L, N, G)

• Hard conduit is run between the circuit breaker box to the flex conduit beside the Dock.

• The Knockout on both sides of the Dock is sized for 1.0" EMT conduit or equivalent to a 2.54 cm diameter hole.

Note:

Located 6.5" (16.5 cm) above ground level.

• To ensure there is enough conduit wiring to the terminal connections inside the Dock, provide an additional 4.0 ft (1.2 m) wire beyond each Dock's knockout location.

• Hardwired power connects to Wago connectors located inside of the Dock.

Conduit Wago Connectors

Skydio Dock for X10 Site Readiness Manual | Page 17

Ethernet Cable Requirements Skydio Device X10 Dock Cable External Radio

Connection X10 Dock to PoE Switch External Radio to X10 Dock or PoE Switch

Conductors 23 AWG Solid Bare Copper 23 AWG Solid Bare Copper

Shielding Aluminum Foil Overall (F/UTP) Aluminum Foil Overall (F/UTP)

Outer Diameter (OD) No Restriction 5.3mm - 6.5mm (Restricted to ensure gland fits)

Jacket CMX rated

Outdoor rated, UV-resistance in compliance with UL444, Withstands temps -40 to 90C (not necessarily direct-burial rated)

CMX rated

Outdoor rated, UV-resistance in compliance with UL444, Withstands temps -40 to 90C (not necessarily direct-burial rated)

Bandwidth Up to 550 MHz Up to 550 MHz

PoE Support Up to 100W (IEEE 802.3af/at/bt, 4PPoE) Up to 100W (IEEE 802.3af/at/bt, 4PPoE)

Certification ANSI/TIA‑568.2 ‑D, cETLus, RoHS ‑3, Fluke tested

ANSI/TIA‑568.2 ‑D, cETLus, RoHS ‑3, Fluke tested

Connectors CAT6 Shielded 23AWG RJ45 Connector CAT6 Shielded 23AWG RJ45 Connector

Strain Relief Strain relief is mandatory on dock side to prevent long term damage.

[Note there is a significant ~30 deg bend when plugged into the dock making the strain relief critical]

No Strain relief on waterproof gland on the External Radio-side.

Strain Relief required if the other side is plugged into the dock. Else optional.

To prevent signal loss for network installations, CAT6A cabling offers higher performance specifications compared to standard CAT6. Ensure cable length is less than 328 ft (100.0 m).

CAT6 cable with solid copper and double shielding is more than sufficient for nearly all installations. CAT6A is not required for Skydio systems as our operations do not utilize the higher throughput speeds it supports.

CAUTION:

Improper installation, routing, or excessive length of Cat6 network cables. Improper cabling may result in degraded data transfer rates and reduced communication reliability. Do not exceed recommended cable length limit. Avoid kinking, sharp bends, or placing excess weight on Cat6 network cables.

When to Consider CAT6A

For installations with long cable runs or environments with significant electrical interference, CAT6A may provide additional protection against signal loss or errors. These are edge scenarios, however, and in the vast majority of deployments, CAT6 will perform reliably without issue.

Skydio Dock for X10 Site Readiness Manual | Page 18

Computer System Requirements

Remote Flight Deck/DFR Command System Requirements

For optimal performance with Remote Flight Deck, and DFR Command, ensure the computers used with the Dock for X10 Flight System meet the requirements below.

For information about network setup and configuration, see: Skydio Dock for X10 Networking Guide.

Note:

Skydio does not support accessing Remote Flight Deck from Virtual Desktop Infrastructure (VDI). Remote Flight Deck must be flown on a local machine.

System Performance Requirements

Category Minimum Recommended

CPU Intel Core i5-8400 or AMD Ryzen 5 2600 Intel Core i7-12700 or AMD Ryzen 7 7700X

RAM 32 GB DDR4 32 GB DDR4 or greater

GPU

Desktop: NVIDIA GTX 1060 or AMD RX

Laptop: NVIDIA GTX 1060 Mobile or AMD

RX 5500M

Desktop: NVIDIA RTX 2070 or AMD Radeon RX 6600 XT

Laptop: NVIDIA RTX 2070 Mobile or AMD Radeon RX 6700M

Network 100 Mbps sustained with latency under 50 ms

1 Gbps Ethernet preferred, or Wi-Fi 6 with minimum 300 Mbps sustained with Latency under 30 ms

Display

Category Minimum Recommended

Resolution 1920 × 1080 (Full HD) 2560 × 1440 on a 30-inch Ultrawide Display

Screen width 1200 pixels 1600 pixels

Screen height 1024 pixels Not Specified

Operating System and Browser Support

Note:

Keep supported browsers up to date.

A 64-bit Operating System is required.

Supported Not Supported

Windows 10 or later, macOS 10.12 or later Linux

Google Chrome, Microsoft Edge Apple Safari, Mozilla Firefox, Microsoft Edge (not based on Chromium), Microsoft Internet Explorer https://support.skydio.com/hc/article_attachments/49656765459867

Skydio Dock for X10 Site Readiness Manual | Page 19

DFR Command Operator Suggested Equipment List

For a DFR Command Operator, Skydio suggests the following equipment:

• A PC meeting all system requirements

• Monitor

• Monitor Stand

• Lighting

• Temp Keyboard

• Chairs

• Desk

Optional Accessories

• Desk Phone

• Walkie Talkie

© 2026 Skydio, Inc. All rights reserved. Proprietary. Printed copies are uncontrolled.

https://www.amazon.com/dp/B0C48D7Q22?ref=fed_asin_title&th=1 https://www.amazon.com/Govee-H6047-Controller-Specially-Assistant/dp/B0B6CQ2LQ2/ref=asc_df_B0B6CQ2LQ2?mcid=49072767fdb533f2b1afc326d6063bef&hvocijid=14498694276282458603-B0B6CQ2LQ2-&hvexpln=73&tag=hyprod-20&linkCode=df0&hvadid=721245378154&hvpos=&hvnetw=g&hvrand=14498694276282458603&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9208144&hvtargid=pla-2281435180218&th=1 https://a.co/d/coYFG4e https://secretlab.co/pages/titan-evo-2022-series https://www.amazon.com/AT-ML17929-2-Line-Corded-Telephone/dp/B007P8DKZ2/ref=sr_1_6?dib=eyJ2IjoiMSJ9.PO3QgZeDUJpWsOx4QLKp9OdffW8Bz12QF31jzye7HspcraoQIHTROjsRYM1Not7XIhU8tKFbsXK_kDBzdOW8Lbig7vydCkOFBu20q2aFHoU9VE1MpNNAILy5apNzhrGWfDQWJ1v162h-Aox5SSHCj6LBThlYzO8z0qAic51Uhbxq4UPYsdyDXZarnGHONo5k4thMlj5lcvkE8TpCpV3uGePZgJAo1ZYbUlvIVV5UacA.4yHRSjE-iSzsZR1wWRwHo-mkIk3e2gnVjVRMb4cUxYg&dib_tag=se&keywords=Desk%2Bphone&qid=1741905502&sr=8-6&th=1 https://www.amazon.com/pxton-Rechargeable-400-470Mhz-Transceiver-Flashlight/dp/B08HK5SXH1/ref=sr_1_7?crid=ULCPBOWPJTW2&dib=eyJ2IjoiMSJ9.ooLFMotY_bQATsTClabi9Vpd-8g3H4qFoNcGd5ATkRvAUw6vbYx-0DtoB92NtmVxqrUrLUAuxALM-xyIKS3ohuM-hhAIFHvcipj-MOxTHVwPJdkyx_5O9JWHGh7YzRvaXzhxcKGl1LEyOpN6xHqRQr4g9Bpo5QMfJjA_kC7uUulIrrreBx7vUt89bCSJk-uGMtPcEG9klYiZhUseboyJqt0XJUeyrZ7IhC-ZttCt-JQX_vy1-61oZfhPLuWiSCOT0u3PHzEIxm5vSZWJ5ZDbrih6VwpgjmtRvfqSwdmzcM7tVsjKFmoJsLp1x9SjfLYCENQm6-0cSK6K_G1CrBnSOtXPG8Jx3mr5JBEfM7aTkhw.PsvRvOw6hD1wGxMdhaagcnzL95jA4v9zWBN5XLkdMxU&dib_tag=se&keywords=walkie+talkie+radio+with+stand&qid=1741905971&s=electronics&sprefix=walkie+talkie+radio+with+stan%2Celectronics%2C192&sr=1-7

Skydio Dock for X10 Site Readiness Manual | Page 20

Installation Requirements

DANGER:

Improper installation or configuration of the Dock for X10. Improper installation or configuration of the Dock for X10 will result in equipment damage, serious injury, or death. For every Dock for X10 installation location, including connectivity and Radio Frequency (RF) mapping, final placement and installation requirements must be determined through a Skydio Site Survey.

Transport and Delivery

Customer Transportation Responsibilities

The Customer is responsible for transporting the Skydio Dock from the shipment destination to the final installation site. Transport may require lifting or craning the pallet to a rooftop or elevated location, depending on site conditions.

WARNING:

Transportation pallet tip hazard. Do not remove the Dock from its shipping pallet until it has reached the designated final installation location. While operating lift equipment, wear appropriate PPE.

To transport, do the following:

• Lift of hoist the Dock in the packaging by crane or telescopic handler.

• If a crane or forklift are not available, separate the Dock into 3x major assemblies for other logistical solutions.

Shipping Information

Type Specification / Requirement

Shipping Dimensions 40 in x 48 in x 58 in (101.6 cm x 121.9 cm x 147.3 cm) Pallet

Total Shipping Weight ~300 to 360 lbs (136.1 to 163.3 kg)

Skydio Dock for X10 Site Readiness Manual | Page 21

Skydio Installation and Validation

Note:

Skydio Authorized Technicians and Field Services teams will perform system assembly and installation, validation testing, RF analysis, connectivity mapping, and system activation.

Skydio Dock for X10 Site Readiness Manual | Page 22

Dock Installation Requirements

DANGER:

Improper installation or configuration of the Dock for X10. Improper installation or configuration of the Dock for X10 will result in equipment damage, serious injury, or death. For every Dock for X10 installation location, including connectivity and Radio Frequency (RF) mapping, final placement and installation requirements must be determined through a Skydio Site Survey.

Layout and Clearance

Obstacle Clearance

The Dock requires an open field of view to the sky within a 15 ft (4.6 m) radius of the dock center point. Inside this zone, any obstacle taller than the dock (ex. fence, wall, building, light pole, or overhanging tree) must be positioned so that its horizontal distance from the dock is at least 1.2 x the obstacle's height (H). Obstacles beyond the 15 ft radius are not restricted. GPS-transparent objects (ex. thin bridges, poles, or towers that do not block the sky view) are exempt.

To support Drone operation and unobstructed approach paths, maintain the following clearances:

• Ensure no tall obstacles are present within a 15 ft (4.6 m) radius surrounding each Dock set.

• Maintain a clear line of sight above and around each Dock.

Obstacle Height 1.2 x H Field Minimum Distance

3.0 ft (0.9 m) 3.6 ft (1.1 m) 4.0 ft (1.2 m)

4.0 ft (1.2 m) 4.8 ft (1.5 m) 5.0 ft (1.5 m)

5.0 ft (1.5 m) 6.0 ft (1.8 m) 6.0 ft (1.8 m)

6.0 ft (1.8 m) 7.2 ft (2.2 m) 8.0 ft (2.4 m)

7.0 ft (2.1 m) 8.4 ft (2.6 m) 9.0 ft (2.7 m)

8.0 ft (2.4 m) 9.6 ft (2.9 m) 10.0 ft (3.0 m)

9.0 ft (2.7 m) 10.8 ft (3.3 m) 11.0 ft (3.4 m)

10.0 ft (3.0 m) 12.0 ft (3.7 m) 12.0 ft (3.7 m)

11.0 ft (3.4 m) 13.2 ft (4.0 m) 14.0 ft (4.3 m)

12.0 ft (3.7 m) 14.4 ft (4.4 m) 15.0 ft (4.6 m)

For Dock Hive information, see: Multiple Docks (Hive) (on page 31)

GNSS Considerations

For the Global Navigation Satellite System (GNSS), note the following:

• Transparent objects are permissible (ex., poles, trees, nets, or items which usually do not fully block GNSS signals). To avoid these violations, users should ensure to set a return height.

• For non-transparent objects, Skydio uses a GPS Survey Tool and may need to consult with internal engineers to determine if the item is permissible to mitigate risk of reduced landing reliability.

Skydio Dock for X10 Site Readiness Manual | Page 23

Approach and Landing

When a Drone is approaching or landing at a Dock, the following conditions apply:

• To detect a Dock during descent, the Drone must descend within 12 ft (3.7 m) above the Dock.

Note:

Obstacle Avoidance (OA) may be deactivated.

• Drone GPS may be inaccurate by a few meters.

• A clear line of sight to the Dock must be maintained.

Note:

This clearance accounts for potential wind, gusts, estimation errors, or control deviations.

Roof Rotation and Space Considerations

To prevent obstruction or damage during roof movement, observe the following:

• For Roof rotation, allow adequate space behind each Skydio Dock.

• The Roof rotates 6.0 in (15.2 cm) above the base of the Dock; ensure no obstructions exist within this rotation zone.

Mounting and Structural Requirements

Note:

Dock for X10 may be freestanding or bolted onto a permanent structure. It is the Customer's sole responsibility to provide permanent mounting of the Dock System and External Radio.

Skydio Dock for X10 Site Readiness Manual | Page 24

Mounting Method

The following mounting methods explain how to secure the Skydio Dock to an installation surface:

Recommended: Secure the Skydio Dock by bolting it to an accessible permanent structure, such as a concrete pad when installing on the ground. The Dock for X10 is approximately 3.1 ft x 2.8 ft and requires a minimum pad size of 4 ft. x 4 ft. x 6 in. (1.2 m x 1.2 m x 15.24 cm).

Note:

Refer to the bolting layout diagram for specific bolt placement.

Pad Dimensions

Alternative Options:

• For installations where bolting is not feasible, the Dock may be mounted using four leveling feet (non-bolted configuration).

• For a roof constructed with soft or non-structural materials, construct a standing platform with the following minimum dimensions: 40 in x 36 in x 4 in (101.6 cm x 91.4 cm x 10.2 cm).

Note:

To ensure proper stability and load distribution, mount the Dock to the standing platform.

Leveling and Surface Requirements

The following requirements apply to leveling and surface preparation:

Skydio Dock for X10 Site Readiness Manual | Page 25

• To ensure proper Dock operation and aircraft landing accuracy, the landing surface must be maintained within ±3° of level.

• Verify level alignment after installation and during periodic maintenance checks.

Dock Feet Guidance

If Dock Feet are required, see the following information:

Category Specification / Requirement

Material Steel (painted, holes for paint/hanging only)

Weight (per "foot") ~18 lbs (8.2 kg)

Total Added Weight ~72 lbs (32.7 kg) Across All 4x Dock Feet

Surface Grip Dock Feet Underside Use Grip Tape Placed on a Rubber Utility Mat Adhered With Tape

Survival Wind Rating • Without Dock Feet (Un-anchored Dock): ~40 mph (54.7 to 64.3 km/h)

• With Dock Feet + Utility Mat: ~80 mph (128.7 km/h)

• Bolted Dock: > 80 mph (128.7 km/h) Up to 160 mph (257 km/h)

Anchor Bolt and Thread Specifications

WARNING:

Improper structural installation or inadequate anchoring. Structural failure under wind loading may result in equipment damage, falling components, or serious injury. For higher wind exposures (C/D) or other elevated load conditions, use engineered mounts or increase anchoring in accordance with applicable code requirements. Validate installation with a licensed structural engineer.

The following specifications apply to all bolt and thread installations:

Mounting Category Fastener

Concrete Pad Steel Wedge Anchor for Concrete

3/8 in -16 x 3 in (M10-1.5 x 75 mm) (McMaster: 91578A823)

Other Structures High-Strength Grade 8 Steel Hex Head Screws

3/8 in -16 x 2 in (M10-1.5 x 75 mm) (McMaster: 97753A137)

Ensure thread exposure above grade meets the following limits:

• Minimum: 1.0 in (25 mm)

• Maximum: 2-3/8 in (6.0 mm)

Use the following diagram for the following:

• Anchor bolt location requirements

• Precise hole spacing

• Bolting pattern

Skydio Dock for X10 Site Readiness Manual | Page 26

Dock Grounding Requirements

The Dock for X10 is grounded via the electrical system and power supply connections during installation.

Skydio Dock for X10 Site Readiness Manual | Page 27

External Radio Installation Requirements For the External Radio, note the following:

• Failure to provide dedicated External Radios may cause communication loss between Docks and the network.

• Each Dock requires 1x External Radio to maintain reliable connectivity and full system performance.

• To avoid any signal loss, ensure the maximum distance between the Dock and External Radio is 100 m.

Distance Between External Radio and Dock / Multiple Radios

Skydio Dock for X10 Site Readiness Manual | Page 28

Mounting Options

WARNING:

Improper structural installation or inadequate anchoring. Structural failure under wind loading may result in equipment damage, falling components, or serious injury. For higher wind exposures (C/D) or other elevated load conditions, use engineered mounts or increase anchoring in accordance with applicable code requirements. Validate installation with a licensed structural engineer.

Improper mounting may result in movement, instability, or loss of communication during operation.

The External Radio may be mounted using one of the following options:

• A Customer-provided pole

• A Freestanding Mount provided by Skydio

Note:

To prevent shifting or tipping when using the Skydio Freestanding Mount, the Customer must secure it with sandbags or 8x cinder blocks 4" x 8" x 16" blocks (~256 lbs).

Mount Type Pole OD Antenna Set Ballast (Cinder Blocks)

Target Wind Rating

Assumptions

Banda-clamped to engineered pole

2 to 4 in Patch or Yagi pair

0 130 mph (209 km/h)

Retention on pole only; pole and anchors engineered to site wind

(ASCE 7)

Non-penetrating ballasted stand

2 to 3 in Patch or Yagi pair

8 80 mph (128 km/h)

Exposure B; standard 4" x 8" x 16" blocks; correct clamp install

External Radio Grounding Requirements

WARNING:

Electrical hazard. Improper grounding can result in electric shock, fire, equipment damage, serious injury, or death. All grounding work must be performed by a qualified electrician in accordance with local codes.

To ensure electrical safety and system stability, the following grounding requirements apply:

• Utility Use Cases: Grounding is recommended using grounding straps or cables attached to the Dock and External Radio.

• All Other Use Cases: Grounding is recommended for improved electrical safety and system stability.

Skydio Authorized Technicians will install a grounding strap between the external radio and the mounting pole.

If using the provided non-penetrating sled, provisions must be made to ground the sled using a conductive fastener or securing the grounding wire between one of the fasteners in the assembly. If using a non-conductive pole, provisions must be made to connect a grounding wire to the lug of the grounding strap fastened to the pole.

Placement and Line of Sight

Poor placement may reduce signal quality and interrupt Drone-to-Dock communication.

Follow these placement guidelines:

Skydio Dock for X10 Site Readiness Manual | Page 29

• For optimal line-of-sight, install the External Radio at the highest point of the roof.

• To maintain clear line of sight in all directions, if no elevated location is available, ensure the mounting pole extends at least 10 ft (3.0 m) above all roof structures.

Mounting Hardware and Stability

Using undersized or unstable supports may cause mount failure in severe weather.

To ensure long-term structural integrity:

• Use a steel mounting pipe with an outer diameter between 2 in to 6 in (5.1 to 15.2 cm).

• Permanently fix the pipe to a structural surface capable of withstanding environmental loads.

• Confirm the assembly remains stable under all expected weather conditions.

Network Cabling

CAUTION:

Improper installation, routing, or excessive length of Cat6 network cables. Improper cabling may result in degraded data transfer rates and reduced communication reliability. Do not exceed recommended cable length limit. Avoid kinking, sharp bends, or placing excess weight on Cat6 network cables.

Meet the following requirements for cabling:

• Use a Customer-provided shielded Cat6 or Cat6A Ethernet cable from the base of the External Radio to the Dock accessory port (or to open internet).

• The cable must be outdoor-rated and shielded, and should be encased in conduit where possible.

• Limit total cable length to less than 328 ft (100.0 m) between the External Radio and Dock.

Final Position Verification

Unverified locations may result in poor RF performance or obstruction interference. All final radio and dock locations must be verified through the Skydio Pre-Site Survey before installation.

Category Specification / Requirement

Horizontal distance between External Radio and Dock Minimum: 17 ft (5.2 m)

Horizontal distance between two or more External Radios Minimum: 17 ft (5.2 m)

Vertical distance between two External Radios mounted to the same pole (from tip-to-tip of the antennas)

Minimum: 18 in (45.7 cm)

Recommended: 36 in (91.4 cm)

Skydio Dock for X10 Site Readiness Manual | Page 30

Category Specification / Requirement

Mounting height and location Loss of signal or reduced range will occur if the external radio's line of sight is obstructed.

To maintain full communication range, observe the following requirements:

• Obstructions will limit the range of Skydio Connect SL in the direction of the blockage.

• The External Radio must maintain an unobstructed line of sight (with added margin for wave spread-out) to the horizon in all directions.

• To prevent interference with the Drone's line-of-sight, he External Radio must be installed at least 5.0 ft (1.5 m) above any walls or roof obstructions.

Skydio Dock for X10 Site Readiness Manual | Page 31

Multiple Docks (Hive)

WARNING:

Improper installation or operation of multiple Skydio Dock for X10 units. Improper installation or operation may result in significant equipment or property damage, severe injury, or death. Follow all safety, electrical, and operational requirements for the installation and operation of multiple Skydio Dock for X10 units.

Hive Layout and Clearance

A Hive is a group of 2 to 6 Docks installed in the same location. When installing a Hive, ensure the following:

• Maintain a minimum of 5.0 ft (1.5 m) between each Dock, side-by-side.

• Maintain a minimum of 15 ft (4.6 m) of clearance around each set of Docks for safe operation and flight maneuvering.

• Provide a 4 ft x 4 ft (1.22 m × 1.22 m) square space nearby as an alternative safe landing zone.

• Final locations to be determined during Skydio Site Survey.

Skydio Dock for X10 Site Readiness Manual | Page 32

Appendixes

Corrosion Guidance Dock for X10 is designed and tested to operate in coastal regions, outside of direct saltwater splash zones.

With the standard Maintenance and Repair package for Dock, Skydio Service Representatives will conduct maintenance and repair visits in order to keep Dock for X10 operational.

Corrosive environments will cause cosmetic degradation and may also result in functional degradation.

Functional degradation can be corrected by replacing corroded components, which is covered under the Dock for X10 Maintenance and Repair package, so long as the deployment is not in an area of direct saltwater exposure. Cosmetic degradation is, however, not covered under the Maintenance and Repair package.

To reduce the likelihood of functional and cosmetic degradation due to corrosion, Skydio recommends that the Dock for X10 be installed at least 200 m from coastline. Deployments inside of 200 m but outside of saltwater splash zones will not void the warranty.

Installation in direct saltwater splash-zones will void the 1-Year Limited Warranty and may result in repairs that are not covered under the Dock for X10 Maintenance and Repair package.

Safety Information

DANGER:

Improper installation or configuration of the Dock for X10. Improper installation or configuration of the Dock for X10 will result in equipment damage, serious injury, or death. For every Dock for X10 installation location, including connectivity and Radio Frequency (RF) mapping, final placement and installation requirements must be determined through a Skydio Site Survey.

DANGER:

Electrical hazard. Exposure to energized components can result in serious injury or death. Follow local/site specific lockout/tagout procedures for de-energizing the Dock and removing electrical hazards. Ensure the work area is clear of unnecessary personnel. If necessary, restrict access to the area.

Before performing service on the unit, do the following:

• Engage the Dock E-Stop button.

• Turn the Dock OFF.

• Disconnect the Dock from the AC power supply.

• Disconnect all external data and power cables from the Dock.

• Complete required lockout/tagout procedures per site requirements.

WARNING:

Ice accumulation when operating below 32°F (0°C) without a 200V-240V power supply. When operating below 32°F (0°C) without a 200V-240V power supply, Dock Heater functionality will be unavailable. Ice accumulation can result in degraded performance, crashes, or loss of the aircraft. For operation below 32°F (0°C), a 200V-240V power supply from a dedicated 20A breaker must be provided to enable Dock Heater functionality. Provide a 100V-120V power supply from a dedicated 15A breaker for operation in temperatures from 32°F (0°C) to 122°F (50°C).

Skydio Dock for X10 Site Readiness Manual | Page 33

WARNING:

Improper installation or operation of multiple Skydio Dock for X10 units. Improper installation or operation may result in significant equipment or property damage, severe injury, or death. Follow all safety, electrical, and operational requirements for the installation and operation of multiple Skydio Dock for X10 units.

WARNING:

Improper structural installation or inadequate anchoring. Structural failure under wind loading may result in equipment damage, falling components, or serious injury. For higher wind exposures (C/D) or other elevated load conditions, use engineered mounts or increase anchoring in accordance with applicable code requirements. Validate installation with a licensed structural engineer.

WARNING:

Transportation pallet tip hazard. Do not remove the Dock from its shipping pallet until it has reached the designated final installation location. While operating lift equipment, wear appropriate PPE.

CAUTION:

Improper installation, routing, or excessive length of Cat6 network cables. Improper cabling may result in degraded data transfer rates and reduced communication reliability. Do not exceed recommended cable length limit. Avoid kinking, sharp bends, or placing excess weight on Cat6 network cables.

NOTICE:

Customer Responsibilities. Skydio will provide Skydio Dock for X10 and External Radio hardware only.

The Customer is solely responsible for providing all infrastructure required for operation, including but not limited to:

• Power

• Electrical work

• Networking

• Wiring between Docks

• Installing protective conduit to encase cable runs

• Mounting

• Site preparation

Skydio assumes no responsibility or liability for any Customer-performed or Customer-provided infrastructure.

Skydio Dock for X10 Site Readiness Manual | Page 34

Revision History

Revision Description Date

1 Initial Release May 7, 2026

2 Updated layout. Removed Operating Environment sections. May 8, 2026

Skydio Dock for X10 Site Readiness Manual

Revision History