HBM_Srain Gauge_Series Y.pdf

B4709-1.0 en HBM: public

Series Y

Strain gages (SG)

Special features

- Flexible and robust

- More than 2,000 variants

- Preferred types available for immediate delivery

- Standard in experimental stress analysis

D a ta s h e e t

B4709-1.0 en HBM: publicHBM 2

Specifications

Strain gage design Foil SG with embedded measuring grid

Carrier

Material Polyimide

Thickness μm 50 ±15

Measuring grid

Material Constantan

Thickness μm approx. 3.8 or 5 (depending on SG type)

Covering

Material Polyimide

Thickness μm 25 ±12

Connections

Leads Nickel-plated copper leads, 30 mm long

Integrated solder tabs Size approx. 1.5 mm x 1.6 mm (depending on type)

Solder tabs with strain relief Nickel-plated copper solder tabs

Nominal (rated) resistance Ω 120, 350, 700 or 1000 (depending on SG type)

Resistance tolerance1) % ±0.3 without, ±0.35 with leads

Gage factor approx. 2 (specified on each package)

Gage factor tolerance

±1.5 (with measuring grid length ≤1.5 mm)

±1.0 (with measuring grid length ≥3mm)

Temperature coefficient of the gage factor

Specified on each package

Transverse sensitivity % Specified on each package

Application temperature range °C (°F) -70 … +200 (-94 … +392) for static measurements -200 … +200 (-328… +392) for dynamic measurements

Temperature response Code:

α for ferritic steel (1) α for aluminum (3) α for austenitic steel (5) α for silica/composite (6) α for titanium (7)

Α for plastic (8) α for molybdenum (9) ppm/K (ppm/°F)

10.8 (6.0)

23 (12.8)

16 (8.9)

0.5 (0.3)

9 (5.0)

65 (36.1)

5.4 (3.0)

Fatigue life2)

Up to a maximum zero drift of ±100μm/m

108 load cycles at ±1,000 μm/m

107 load cycles at ±1,200 μm/m

104 load cycles at ±2,200 μm/m

102 load cycles at ±3,500 μm/m

Up to a maximum zero drift of +/- 30μm/m 107 load cycles at ±1,000 μm/m

Maximum elongation

Positive direction

Negative direction μm/m μm/m

50,000 (5%)

50,000 (5%)

Minimum radius of curvature 0.3 mm for SG with leads

0.3 mm for SG with integrated solder tabs in measuring grid area

2.0 mm in solder tab area

Applicable adhesives Z70, X60, X280, EP150 and EP310S

1) With measuring grid lengths of 0.3 and 0.6 mm, the nominal resistance may deviate by ± 1%. For the types LY51/LY5x the deviation is ±0.75%. For XY9x, RY9x and the KY types (per chain) it is ±0.5%.

2) The data depend on the various parameters of the specific application and are therefore stated for representative examples only.

B4709-1.0 en HBM: public 3 HBM

Fatigue life (testing up to a zero drift of ±100μm/m)

L e v e l o f s tr a in μ m /m

Number of load cycles

Types and dimensions

The following temperature matching codes (1 … 9) apply to all types

1 = Ferritic steel (10.8 ppm/K; 6.0 ppm/°F) 3 = Aluminum (23 ppm/K; 12.8 ppm/°F) 5 = Austenitic steel (16 ppm/K, 8.9 ppm/°F) 6 = Silica/composite (0,5 ppm/K; 0.3 ppm/°F) 7 = Titanium and gray cast iron (9 ppm/K; 5.0 ppm/°F) 8 = Plastic (65 ppm/K; 36.1 ppm/°F) 9 = Molybdenum (5.4 ppm/K; 3.0 ppm/°F)

B4709-1.0 en HBM: publicHBM 4

Series Y: LY1

Linear strain gage with leads below the measuring grid

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY1�-0.3/120 2) 10 120 0.3 0.9 2 1.2 0.6 LS7 1

1-LY1�-0.6/120 2) 10 120 0.6 1 5 3.2 1.5 LS7 1, 3

1-LY1�-1.5/120 10 120 1.5 1.2 6.5 4.7 2.5 LS7 1, 3

1-LY1�-3/120 10 120 3 1.6 8.5 4.5 4 LS7 1, 3

1-LY1�-3/120A 5) 10 120 3 1.6 8.5 4.5 4 LS7 1

1-LY1�-6/120 10 120 6 2.7 13 6 8 LS5 1, 3

1-LY1�-6/120A 5) 10 120 6 2.7 13 6 8 LS5 1

1-LY1�-10/120 10 120 10 4.6 18.5 9.5 13 LS5 1, 3

1-LY1�-10/120A 5) 10 120 10 4.6 18.5 9.5 13 LS5 1

1-LY1�-1.5/350 2) 10 350 1.5 1.2 5.7 4.7 4.5 LS7 1, 3

1-LY1�-3/350 10 350 3 1.6 8.5 4.5 7 LS7 1, 3

1-LY1�-3/350A 5) 10 350 3 1.6 8.5 4.5 7 LS7 -

1-LY1�-6/350 10 350 6 2.8 13 6 13 LS5 1, 3

1-LY1�-6/350A 5) 10 350 6 2.8 13 6 13 LS5 -

1-LY1�-10/350 10 350 10 5.0 18.5 9.5 23 LS5 1

1-LY1�-10/350A 5) 10 350 10 5.0 18.5 9.5 23 LS5 -

Series Y: LY2

Linear strain gage with leads on both sides of the measuring grid

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY2�-0.6/120 2) 10 120 0.6 0.6 3.5 6.4 1 LS7 1

1-LY2�-1.5/120 10 120 1.5 1.5 4.7 8.3 2 LS5 -

1-LY2�-3/120 10 120 3 2.8 7.5 10 6 LS5 1

1-LY2�-6/120 10 120 6 6 11 16 12 LS4 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

3) Maximum permissible effective supply voltage (specified for steel)

4) Preferred types (available from stock) with the temperature matches specified in the column

5) With application aid (cut-to-size polyimide adhesive strip for easy positioning)

B4709-1.0 en HBM: public 5 HBM

Series Y: LY4

Linear strain gage with integrated solder tabs below the measuring grid

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY4�-0.6/120 2) 10 120 0.6 1.1 6 4 1.5 1

1-LY4�-1.5/120 10 120 1.5 1.2 7 5 2.5 1

1-LY4�-3/120 10 120 3 1.2 8 5 3.5 1, 3

1-LY4�-3/120A 5) 10 120 3 1.2 8 5 3.5 -

1-LY4�-6/120 10 120 6 2.7 13.9 5.9 8 1, 3

1-LY4�-6/120A 5) 10 120 6 2.7 13.9 5.9 8 1

1-LY4�-10/120 10 120 10 4.9 18 8 14 1

1-LY4�-10/120A 5) 10 120 10 4.9 18 8 14 -

1-LY4�-20/120 10 120 20 0.5 31.8 8.2 6.5 1

1-LY4�-50/120 10 120 50 0.8 63.6 8.2 12 1

1-LY4�-100/120 10 120 100 1 114.8 8.2 19 1

1-LY4�-150/120 10 120 150 1.2 165.6 8.2 25 1

1-LY4�-1.5/350 2) 10 350 1.5 2.3 9.2 5.9 6.5 1

1-LY4�-3/350 10 350 3 2.5 10.9 5.9 9 1, 3

1-LY4�-3/350A 5) 10 350 3 2.5 10.9 5.9 9 1

1-LY4�-6/350 10 350 6 2.8 13.9 5.9 15 1, 3, 6

1-LY4�-6/350A 5) 10 350 6 2.8 13.9 5.9 15 -

1-LY4�-10/350 10 350 10 5 18 8 24 1

1-LY4�-10/350A 5) 10 350 10 5 18 8 24 -

1-LY4�-3/700 10 700 3 2.7 10.9 5.9 13 1, 3

1-LY4�-6/700 10 700 6 4.1 13.9 5.9 23 1

1-LY4�-10/700 10 700 10 5 18 8 33 -

1-LY4�-3/1000 2) 10 1.000 3 2.7 10.9 5.9 16 -

1-LY4�-6/1000 10 1.000 6 4.2 13.9 5.9 27 1

1-LY4�-10/1000 10 1.000 10 5 18 8 40 -

Series Y: LY5

Linear strain gage with very narrow measuring grid and leads above and below the measuring grid

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY5�-3/120 10 120 3 0.4 9 4.7 2 LS7 -

1-LY5�-6/120 10 120 6 0.4 13 4.7 3 LS7 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

3) Maximum permissible effective supply voltage (specified for steel)

4) Preferred types (available from stock) can be supplied with the temperature matches specified in the column

B4709-1.0 en HBM: publicHBM 6

Series Y: LY6 Linear strain gage featuring solder tabs with strain relief below the measuring grid end.

Ideal for alternating loads on a higher level of strain

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY6�-1.5/120 10 120 1.5 1.0 7.8 4.7 2.5 1

1-LY6�-3/120 10 120 3 1.5 9.8 4.7 4 1

1-LY6�-6/120 10 120 6 2.7 16 6.3 8 1, 3

1-LY6�-10/120 10 120 10 4.6 23.5 9.3 13 1

1-LY6�-3/350A 5) 10 350 3 1.6 9.8 4.7 7 -

1-LY6�-3/350 10 350 3 1.6 9.8 4.7 7 1

1-LY6�-6/350A 5) 10 350 6 2.8 16 6.3 13 1

1-LY6�-6/350 10 350 6 2.8 16 6.3 13 1, 3, 6

1-LY6�-10/350 10 350 10 5 23.5 9.3 21 1

Series Y: LY7 Linear strain gage with integrated solder tabs on both sides of the measuring grid

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY7�-0.6/120 2) 10 120 0.6 1 2.3 5.6 1 1

1-LY7�-1.5/120 10 120 1.5 1.5 3.4 7.5 2.5 1

1-LY7�-3/120 10 120 3 2.8 5.5 10.5 5 1

1-LY7�-6/120 10 120 6 6 9 15.5 10 -

1-LY7�-1.5/350 2) 10 350 1.5 1.6 3.4 7.5 5 1, 3

1-LY7�-3/350 10 350 3 2.7 5.5 10.5 8.5 1

1-LY7�-6/350 10 350 6 5.6 9 15.5 18 -

Series Y: LY8 Linear strain gage with integrated solder tabs above and below the measuring grid

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY8�-0.6/120 2) 10 120 0.6 1 5.6 2.3 1 -

1-LY8�-1.5/120 10 120 1.5 1.5 7.5 3.4 2.5 1

1-LY8�-3/120 10 120 3 3 10.5 5.5 5 1

1-LY8�-6/120 10 120 6 6 15.5 9 10 -

1-LY8�-1.5/350 2) 10 350 1.5 1.5 7.5 3.4 5 1

1-LY8�-3/350 10 350 3 3 10.5 5.5 8.5 -

1-LY8�-6/350 10 350 6 5.6 15.5 9 18 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

3) Maximum permissible effective supply voltage (specified for steel)

B4709-1.0 en HBM: public 7 HBM

Series Y: LY9

Linear strain gage with integrated solder tabs on the side of the measuring grid

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-LY9�-1.5/350_E 2) 10 350 1.5 2 4.7 6.6 5 1

1-LY9�-3/350_E 10 350 3 2 6.3 7 7.5 1

1-LY9�-6/350_E 10 350 6 3.8 9.5 9.5 15 1

Series Y: DY1

Double linear strain gage with two parallel measuring grids and leads below the measuring grids

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-DY1�-3/350 5 350 3 2.7 9 8 9 LS7 1, 3

1-DY1�-6/350 5 350 6 3.2 12.5 9.4 14 LS7 1, 3

Series Y: DY4

Double linear strain gage with two parallel measuring grids and integrated solder tabs below the measur ing grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-DY4�-1.5/350 2) 5 350 1.5 1.8 5.5 6 5 1

1-DY4�-3/350 5 350 3 2.7 8.2 8 8.5 1, 3

1-DY4�-6/350 5 350 6 3.2 10.7 9 13 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

3) Maximum permissible effective supply voltage (specified for steel)

B4709-1.0 en HBM: publicHBM 8

Series Y: XY1

T rosette with two separate measuring grids and leads on both sides of the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-XY1�-0.6/120 2) 5 120 0.6 1.1 6 4 1.5 LS7 1

1-XY1�-1.5/120 5 120 1.5 1.5 9 5 3 LS5 1, 3

1-XY1�-3/120 5 120 3 3.2 14.5 7.5 6 LS4 1, 3

1-XY1�-6/120 5 120 6 6.5 23.5 11 12 LS5 1

1-XY1�-1.5/350 2) 5 350 1.5 1.5 9 5 5 LS5 1

1-XY1�-3/350 5 350 3 3.1 14.4 7.3 10 LS4 1, 3

1-XY1�-6/350 5 350 6 6.3 23.3 10.5 20 LS4 1

Series Y: XY1_E

Double shear strain gage with integrated solder tabs above and below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b1 b2 c d

1-XY1�-1.5/350_E 2) 5 350 1.5 2.2 2.9 7.8 4.9 4.5 1

1-XY1�-3/350_E 5 350 3 4.4 4.9 10 6.9 9 1

1-XY1�-6/350_E 5 350 6 6.2 10.2 12.3 11.7 14.5 -

Series Y: XY2

Shear/torsion strain gage with two measuring grids connected to form a half bridge and leads above and below the measuring grid

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminal s

Pre ferred types4)Measuring grid Carrier

Ω a b1 b2 c d

1-XY2�-0.6/120 2) 5 120 0.6 2.2 1.1 7.5 4 2.5 LS7 -

1-XY2�-1.5/120 5 120 1.5 1.7 2.5 6.8 4.5 4.5 LS7 1

1-XY2�-3/120 5 120 3 3.7 5.3 11.2 9.5 6 LS4 1

1-XY2�-6/120 5 120 6 8 10 17.5 12.7 11 LS4 1

1-XY2�-1.5/350 2) 5 350 1.5 2.2 2.5 7.4 4.5 5 LS7 1

1-XY2�-3/350 5 350 3 4.2 5.3 11.2 9.5 10 LS4 1

1-XY2�-6/350 5 350 6 8 10 17.5 12.7 19 LS4 1

1-XY2�-3/700 2) 5 700 3 4.0 4.7 11.2 9.5 14 LS5 -

1-XY2�-6/700 5 700 6 7.8 9.2 17.5 12.7 27 LS4 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: public 9 HBM

Series Y: XY3

T rosette with two separate measuring grids and integrated solder tabs below the measuring grids.

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-XY3�-0.6/120 2) 5 120 0.6 1 7 6 1.5 1

1-XY3�-1.5/120 5 120 1.5 1.6 8 6.3 3 1, 3

1-XY3�-3/120 5 120 3 3.2 10.5 8 5.5 1

1-XY3�-6/120 5 120 6 6.3 17.5 12 11 1

1-XY3�-1.5/350 2) 5 350 1.5 1.7 7.7 6.3 5 1

1-XY3�-3/350 5 350 3 3.3 10.9 7.6 10 1, 3

1-XY3�-6/350 5 350 6 6.5 18 12 20 1, 3, 6

Series Y: XY4

Shear/torsion strain gage with two measuring grids connected to form a half bridge and integrated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b1 b2 c d

1-XY4�-0.6/120 2) 5 120 0.6 2.2 1.6 6.5 4.6 1.5 1

1-XY4�-1.5/120 5 120 1.5 1.8 3.1 7.5 4.6 2.5 1

1-XY4�-3/120 5 120 3 3 5.4 11 8 5 1

1-XY4�-6/120 5 120 6 6 10.2 16 12.2 9.5 1

1-XY4�-1.5/350 2) 5 350 1.5 2.1 3.1 7.5 4.5 4 1

1-XY4�-3/350 5 350 3 4.2 5.6 11 8 9.5 1, 3

1-XY4�-6/350 5 350 6 6 10 16 12.2 16 1

1-XY4�-3/700 5 700 3 4.2 5.6 11 8 13.5 1

1-XY4�-6/700 5 700 6 6.1 9.9 16 12.2 23 -

Series Y: XY7

T rosette with two measuring grids connected to form a half bridge and integrated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-XY7�-0.6/120 2) 5 120 0.6 0.8 5.7 4.3 1 -

1-XY7�-1.5/120 5 120 1.5 1.4 6.5 5.3 2.5 -

1-XY7�-3/120 5 120 3 3 9.9 7.3 5.5 -

1-XY7�-6/120 5 120 6 5.7 16.2 11 11 1

1-XY7�-1.5/350 2) 5 350 1.5 1.4 6.5 5.3 4.5 1, 3

1-XY7�-3/350 5 350 3 3 9.9 7.3 9.5 1, 3

1-XY7�-6/350 5 350 6 5.7 16.2 11 18.5 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: publicHBM 10

Series Y: XY9

T rosette with two separate stacked measuring grids and leads on the sides of the measuring grids

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder termi nals

Pre ferred types4)Measuring grid Carrier

Ω a b1 b2 c d

1-XY9�-1.5/120 5 120 1.5 1.2 1.2 4.7 6.7 1 LS5 1, 3

1-XY9�-3/120 5 120 3 1.4 1.4 6.2 7.9 2 LS5 1, 3

1-XY9�-6/120 5 120 6 1.9 2.2 10 9.6 3.5 LS4 1, 3

1-XY9�-10/120 5 120 10 3.2 3.8 15.2 14.0 6.5 LS212 1

1-XY9�-1.5/350 2) 5 350 1.5 1.5 1.5 4.7 6.7 2.5 LS5 1

1-XY9�-3/350 5 350 3 1.5 1.5 6.2 7.9 3.5 LS5 1, 3

1-XY9�-6/350 5 350 6 2 2.2 10 9.6 6 LS4 1, 3

1-XY9�-10/350 5 350 10 3.3 3.7 15.2 14 11.5 LS212 -

Series Y: XY10

T rosette with two separate measuring grids and solder tabs with strain relief below the measuring grids. Ideal for alternating loads on a higher level of strain

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-XY10�-1.5/120 5 120 1.5 1.6 8 8.3 1.5 -

1-XY10�-3/120 5 120 3 3.2 10.6 9.8 3 1

1-XY10�-6/120 5 120 6 6.5 18 16.5 5.5 -

1-XY10�-3/350 5 350 3 3.3 10.6 9.8 11 1, 3

1-XY10�-6/350 5 350 6 6 18 16.5 10 -

Series Y: RY1

Round rosette with three measuring grids in 0°/45°/90° arrangement and leads

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder termi nals

Pre ferred types4)Measuring grid Carrier

Ω a1 a2 b c d

1-RY1�-3/120 2) 5 120 0.8 3 0.8 7 7 1.5 LS7 1

1-RY1�-6/120 5 120 2 6 1.4 11 11 3 LS5 1, 3

1-RY1�-10/120 5 120 2.9 10 2.7 15.4 15.4 5 LS4 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: public 11 HBM

Series Y: RY3

Round rosette with three measuring grids in 0°/45°/90° arrangement and integrated solder tabs

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a1 a2 b d

1-RY3�-3/120 2) 5 120 0.8 3 0.8 6.9 1.5 1

1-RY3�-6/120 5 120 2 6 1.4 11 3 1, 3

1-RY3�-10/120 5 120 2.9 10 2.7 15.4 5 1

Series Y: RY4

Round rosette with three measuring grids in 0°/60°/120° arrangement and leads

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax 3)

Solder terminals

Pre ferred types4)Measuring grid Carrier

Ω a1 a2 b c d

1-RY4�-3/120 2) 5 120 0.8 3 0.8 7 7 1.5 LS7 -

1-RY4�-6/120 5 120 2 6 1.4 11 11 3 LS5 1

1-RY4�-10/120 5 120 2.9 10 2.7 15.4 15.4 5 LS4 1

Series Y: RY7

Round rosette with three measuring grids in 0°/60°/120° arrangement and integrated solder tabs

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a1 a2 b d

1-RY7�-3/120 2) 5 120 0.8 3 0.8 6.9 1.5 -

1-RY7�-6/120 5 120 2 6 1.4 11 3 -

1-RY7�-10/120 5 120 2.9 10 2.7 15.4 5 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: publicHBM 12

Series Y: RY8

Rectangular rosette with three measuring grids in 0°/45°/90° arrangement and integrated solder tabs below the measuring grids.

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-RY8�-0.6/120 2) 5 120 0.6 1.1 4.8 8.7 1.6 -

1-RY8�-1.5/120 5 120 1.5 1.2 8.2 14.6 2.5 1

1-RY8�-3/120 5 120 3 1.1 9.7 14.6 3 1, 3

1-RY8�-6/120 5 120 6 3 13 22.9 7.5 1

1-RY8�-1.5/350 2) 5 350 1.5 1.6 8.2 14.6 5 -

1-RY8�-3/350 5 350 3 1.2 9.7 14.6 5.5 -

1-RY8�-6/350 5 350 6 2.8 13.1 22.9 13 1

Series Y: RY9

Rectangular rosette with three stacked measuring grids in 0°/45°/90° arrangement and leads below the measuring grids

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-RY9�-1.5/120 5 120 1.5 1.3 9 8 1.5 LS7 1

1-RY9�-3/120 5 120 3 1.3 9 9 2 LS7 1, 3

1-RY9�-6/120 5 120 6 2.6 12.5 11.4 4.5 LS7 1, 3

1-RY9�-10/120 5 120 10 4 17.5 16 7 LS7 1, 3

1-RY9�-1.5/350 2) 5 350 1.5 1.5 8 9 2.5 LS7 1

1-RY9�-3/350 5 350 3 1.5 9 9 3.5 LS7 1, 3

1-RY9�-6/350 5 350 6 2.6 12.5 11.4 6 LS7 1

1-RY9�-10/350 5 350 10 4 17.6 16 11.5 LS7 -

Series Y: RY10

Rectangular rosette with three measuring grids in 0°/45°/90° arrangement and solder tabs with strain relief below the measuring grids. Ideal for alternating loads on a higher level of strain

Ordering number 1) Pcs.

per pack

Nominal (rated) re sistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-RY10�-1.5/120 5 120 1.5 1.4 8.2 13.5 2.5 -

1-RY10�-3/120 5 120 3 1.1 9.7 13.5 3 1, 3

1-RY10�-6/120 5 120 6 3 16.4 22.9 7.5 -

1-RY10�-1.5/3502) 5 350 1.5 1.4 8.2 13.5 5 1, 3

1-RY10�-3/350 5 350 3 1.2 9.7 13.5 5.5 1, 3

1-RY10�-6/350 5 350 6 2.8 16.4 22.9 12 1, 3, 6

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: public 13 HBM

Series Y: VY1

Strain gage with four measuring grids connected to form a full bridge and leads

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-VY1�-3/120 5 120 3 7 13.5 13.5 6 LS5/7 1

1-VY1�-6/120 5 120 6 14 23 23 12 LS5/7 1

Series Y: VY4

Shear/torsion strain gage with four measuring grids connected to form a full bridge and integrated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-VY41�-3/120 5 120 3 1.3 9.8 10 3.5 1

1-VY41�-6/120 5 120 6 2.7 18 17 7.5 -

1-VY41�-3/350 5 350 3 1.2 9.8 10 6 1, 3

1-VY41�-6/350 5 350 6 2.7 18 17 13 -

Series Y: MY2

Diaphragm rosette with four measuring grids connected to form a full bridge and leads

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier

Ω a b c d

1-MY2�-6/120 5 120 6 – 7.3 – 3.5 LS7 -

1-MY2�-15/350 5 350 15 – 17 – 13 LS5 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: publicHBM 14

Series Y: SG chains KY1

Strain gage chain with 10 measuring grids parallel to the chain axis and leads on both sides

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY1�-1/120 2) 1 120 0.6 1 7.2 14.5 1 2 LS7 1

1-KY1�-2/120 1 120 1.5 1.3 6.7 24.5 2 2.5 LS7 1

1-KY1�-4/120 1 120 3 2.1 9.7 44.5 4 5 LS7 1

Series Y: SG chains KY2

Strain gage chain with 10 measuring grids perpendicular to the chain axis and leads on both sides

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY2�-1/120 2) 1 120 0.8 0.8 6.9 15 1 1.5 LS7 1

1-KY2�-2/120 1 120 1.7 1.7 9.5 27 2 3.5 LS7 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: public 15 HBM

Series Y: SG chains KY3

Rosette chain (5 rosettes each with 3 0°/60°/120° measuring grids) with leads on both sides

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY3�-4/120 1 120 1.2 1.3 8.3 24 4 2.5 LS7 -

Series Y: SG chains KY4

Strain gage chain with 10 measuring grids (alternating, 5 parallel, 5 perpendicular) and leads on both sides

Ordering number 1)

Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Solder terminals Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY4�-2/120 1 120 1.2 1.3 9.2 24.5 2 2.5 LS7 -

1-KY4�-4/120 1 120 3 3 11.5 44.5 4 6 LS5 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: publicHBM 16

Series Y: SG chains KY5

Strain gage chain with 10 measuring grids with a shared connection parallel to the chain axis and inte grated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY5�-1/120 2) 5 120 0.6 1.2 5.6 12.8 1 1.5 -

1-KY5�-2/120 5 120 1.5 1.4 6 22.8 2 2.5 -

Series Y: SG chains KY6

Strain gage chain with 10 measuring grids with a shared connection perpendicular to the chain axis and integrated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY6�-1/120 2) 5 120 0.8 0.7 5.6 12.8 1 1.2 -

1-KY6�-2/120 5 120 1.3 1.6 6 22.8 2 2.5 -

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: public 17 HBM

Series Y: SG chains KY7

Strain gage chain with 10 measuring grids with a shared connection (alternating, 5 parallel, 5 perpendicu lar) and integrated solder tabs below the measuring grids

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY7�-2/120 5 120 1.3 1.5 6 22.8 2 2.5 -

Series Y: SG chains KY8

Strain gage chain with 10 measuring grids parallel to the chain axis and integrated solder tabs

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY8�-2/120 5 120 1 1 5 21.7 2 2 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

B4709-1.0 en HBM: publicHBM 18

Series Y: SG chains KY9

Strain gage chain with 10 measuring grids perpendicular to the chain axis and integrated solder tabs

Ordering number 1) Pcs.

per pack

Nominal (rated) resistance

Dimensions [mm] Vmax

3) Pre ferred types4)Measuring grid Carrier Pi-tch

Ω a b c d t

1-KY9�-2/120 5 120 1.2 1.2 5 21.7 2 2 1

1) Strain gages are available in various temperature matches (see codes, page 3).

Insert the code in place of the placeholder “�” to get the ordering number of the strain gage you need

2) Only available in matches for aluminum, ferritic and austenitic steel

3) Maximum permissible effective supply voltage (specified for steel)

4) Preferred types (available from stock) with the temperature matches specified in the column measure and predict with confidence

Hottinger Baldwin Messtechnik GmbH

Im Tiefen See 45 ⋅ 64293 Darmstadt ⋅ Germany

Tel. +49 6151 803‐0 ⋅ Fax +49 6151 803‐9100

E-mail: info@hbm.com ⋅ www.hbm.com

Subject to modifications.

All product descriptions are for general information only. They are not to be understood as a guarantee of quality or durability.

B -1

.0 e n

H

B M p u b lic