Amendment_0004_attachment.pdf

The purpose of this amendment is to provide answers to questions that have been asked, and to update the wage determination:

1. Incorporate the following questions/answers into the solicitation:

QUESTION 1: Roof plans indicate fully adhered EPDM, on Backer Board, on 2 layers 1.5” R7.5 insulation, on Backer Board, on metal deck. Details do NOT indicate the Backer Board on the metal deck, although it is required for a Class A roof if the insulation is to be extruded polystyrene insulation. Please confirm the note on the roof plan is correct?

ANSWER 1: The roof plan notes are correct. A backer board should be installed to in the metal roof deck.

QUESTION 2: Is it acceptable to quote 2 layers 1.5” R8.6 POLYISOCYANURATE insulation in lieu of extruded insulation and thus eliminate the need for backer board above or below the insulation and still maintaining a Class A roof assembly?

ANSWER 2: Contractor’s will bid with extruded insulation and the layer of backer board included on the metal deck.

QUESTION 3: Regarding the bid bond for the Roof Repair, Bldg 6900, can you please specify the amount of the bid bond required?

ANSWER 3: In accordance with FAR 52.228-1, the bid guarantee shall be 20% of the bid price or $150,000, whichever is less.

QUESTION 4: Please provide the specific bid forms for the solicitation.

ANSWER 4: A successful bid package shall include: a completed SF 1442 (blocks 19 and 20 executed), a completed bid schedule (schedule B of the solicitation), registration in both SAM and ORCA websites, and a properly executed bid guarantee with a federally approved surety bonds company.

QUESTION 5: Have cores been taken of the existing roof?

ANSWER 5: During the site visit conducted 12 Sep 2017, a contractor took a core sample for the audience to see, and promptly repaired the roof. It is believed that this core revealed 5 ½” of insulation material to be removed from the roof, which is supported by the drawings.

However, this information cannot be verified for accuracy, and no other cores can be taken at this time due to weather.

QUESTION 6: Is Versico an acceptable substitute to the roofing material specified in the solicitation?

ANSWER 6: After review, yes, Versico is determined to be an acceptable substitute subject to paragraph a of the the Clause at FAR 52.236-5: Materials and Workmanship and all other terms and conditions in this solciatation. See attached brochure for further information on product.

1055159340N Typewritten Text

1055159340N Typewritten Text

1055159340N Typewritten Text

2. Davis Bacon Wage Rates are applicable to this project. Current prevailing wage determination(s) at time of issuance of solicitation are MI180079, 01/05/2018, MI 79, Mod 0.

Applicable wage rates can be found at Applicable wage rates can be found at http://www.wdol.gov/wdol/scafiles/davisbacon/MI79.dvb

3. All other terms and conditions shall remain the same.

http://www.wdol.gov/wdol/scafiles/davisbacon/MI79.dvb

General Decision Number: MI180079 01/05/2018 MI79

Superseded General Decision Number: MI20170079

State: Michigan

Construction Type: Building

County: Calhoun County in Michigan.

BUILDING CONSTRUCTION PROJECTS (does not include single family homes or apartments up to and including 4 stories).

Note: Under Executive Order (EO) 13658, an hourly minimum wage of $10.35 for calendar year 2018 applies to all contracts subject to the Davis-Bacon Act for which the contract is awarded (and any solicitation was issued) on or after January 1, 2015.

If this contract is covered by the EO, the contractor must pay all workers in any classification listed on this wage determination at least $10.35 per hour (or the applicable wage rate listed on this wage determination, if it is higher) for all hours spent performing on the contract in calendar year 2018. The EO minimum wage rate will be adjusted annually.

Please note that this EO applies to the above-mentioned types of contracts entered into by the federal government that are subject to the Davis-Bacon Act itself, but it does not apply to contracts subject only to the Davis-Bacon Related Acts, including those set forth at 29 CFR 5.1(a)(2)-(60). Additional information on contractor requirements and worker protections under the EO is available at www.dol.gov/whd/govcontracts.

Modification Number Publication Date 0 01/05/2018

ASBE0047-002 07/01/2016

Rates Fringes

ASBESTOS WORKER/HEAT & FROST

INSULATOR........................$ 30.22 16.48

BOIL0169-001 01/01/2016

Rates Fringes

BOILERMAKER......................$ 33.88 30.39

BRMI0009-031 08/01/2016

Rates Fringes

BRICKLAYER.......................$ 27.69 16.93

TILE FINISHER....................$ 21.79 11.04

TILE SETTER......................$ 23.04 12.39

CARP0525-003 06/01/2017

1/18/2018https://www.wdol.gov/wdol/scafiles/davisbacon/MI79.dvb?v=0

Rates Fringes

CARPENTER, Includes Acoustical Ceiling Installation, Drywall Hanging, and Form Work...........$ 22.15 19.30

CARP1102-001 06/01/2017

Rates Fringes

MILLWRIGHT.......................$ 25.24 24.54

ELEC0445-011 05/29/2017

Rates Fringes

ELECTRICIAN......................$ 31.00 19.38

ENGI0324-002 06/01/2017

Rates Fringes

OPERATOR: Power Equipment

GROUP 1.....................$ 37.58 23.30

GROUP 2.....................$ 34.28 23.30

GROUP 3.....................$ 31.63 23.30

GROUP 4.....................$ 29.92 23.30

GROUP 5.....................$ 29.92 23.30

GROUP 6.....................$ 24.06 23.30

GROUP 7.....................$ 21.58 23.30

FOOTNOTES:

Crane operator with main boom and jib 300' or longer: $1.50 per hour above the group 1 rate.

Crane operator with main boom and jib 400' or longer: $3.00 per hour above the group 1 rate.

PAID HOLIDAYS: New Year's Day, Memorial Day, Fourth of July, Labor Day, Thanksgiving Day and Christmas Day.

POWER EQUIPMENT OPERATOR CLASSIFICATIONS

GROUP 1: Crane operator with main boom and jib 400', 300', or 220' or longer.

GROUP 2: Crane operator with main boom and jib 140' or longer, tower crane, gantry crane, whirley derrick

GROUP 3: Backhoe/Excavator/Trackhoe; Crane; Concrete Pump;

Grader/Blade; Highlift; Hoist; Loader; Roller; Scraper;

Stiff Leg Derrick; Trencher

GROUP 4: Bobcat/Skid Loader; Broom/Sweeper; Fork Truck (over 20' lift)

GROUP 5: Boom Truck (non-swinging)

GROUP 6: Fork Truck (20' lift and under for masonry work)

GROUP 7: Oiler

* IRON0340-002 06/19/2017

Rates Fringes

IRONWORKER, REINFORCING AND

STRUCTURAL.......................$ 24.43 24.67

LABO0355-022 06/01/2016

Rates Fringes

LABORER

Common or General; Grade Checker; Mason Tender - Brick; Mason Tender - Cement/Concrete;

Sandblaster.................$ 20.09 12.85 Pipelayer...................$ 20.34 12.85

PAIN0312-002 06/01/2017

Rates Fringes

PAINTER: Brush and Roller.......$ 23.72 12.52 PAINTER: Drywall Finishing/Taping.................$ 23.72 12.52 PAINTER: Spray..................$ 24.92 12.52

PLAS0016-007 04/01/2014

Rates Fringes

PLASTERER........................$ 21.18 12.43

PLUM0333-006 06/01/2017

Rates Fringes

PIPEFITTER, Includes HVAC Pipe and Unit Installation.......$ 35.89 21.13 PLUMBER, Excludes HVAC Pipe and Unit Installation............$ 35.89 21.13

FOOTNOTE:

Paid Holidays: Memorial Day, Independence Day and Labor Day, if the employee works the work day preceding and following the holiday unless proven illness or injury prevents the employee from working.

ROOF0070-002 06/01/2017

Rates Fringes

ROOFER...........................$ 27.80 13.79

SFMI0669-001 04/01/2017

Rates Fringes

SPRINKLER FITTER (Fire Sprinklers)......................$ 34.87 15.84

SHEE0007-004 07/01/2017

Rates Fringes

SHEET METAL WORKER (Including HVAC Duct Installation;

Excluding HVAC System Installation)....................$ 31.26 19.71

SUMI2011-004 02/01/2011

Rates Fringes

CEMENT MASON/CONCRETE FINISHER...$ 25.23 1.80

IRONWORKER, ORNAMENTAL...........$ 18.48 7.93

LABORER: Landscape & Irrigation.......................$ 10.38 0.50

OPERATOR: Bulldozer.............$ 19.68 6.64

OPERATOR: Compactor.............$ 17.68 6.70

OPERATOR: Tractor...............$ 19.10 8.48

TRUCK DRIVER, Includes Dump and Tandem Truck.................$ 17.26 11.42

TRUCK DRIVER: Lowboy Truck......$ 14.50 0.44

TRUCK DRIVER: Tractor Haul Truck............................$ 13.57 1.18

WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental.

Note: Executive Order (EO) 13706, Establishing Paid Sick Leave for Federal Contractors applies to all contracts subject to the Davis-Bacon Act for which the contract is awarded (and any solicitation was issued) on or after January 1, 2017. If this contract is covered by the EO, the contractor must provide employees with 1 hour of paid sick leave for every 30 hours they work, up to 56 hours of paid sick leave each year.

Employees must be permitted to use paid sick leave for their own illness, injury or other health-related needs, including preventive care; to assist a family member (or person who is like family to the employee) who is ill, injured, or has other health-related needs, including preventive care; or for reasons resulting from, or to assist a family member (or person who is like family to the employee) who is a victim of, domestic violence, sexual assault, or stalking. Additional information on contractor requirements and worker protections under the EO is available at www.dol.gov/whd/govcontracts.

Unlisted classifications needed for work not included within the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses (29CFR 5.5 (a) (1) (ii)).

The body of each wage determination lists the classification and wage rates that have been found to be prevailing for the cited type(s) of construction in the area covered by the wage determination. The classifications are listed in alphabetical order of "identifiers" that indicate whether the particular rate is a union rate (current union negotiated rate for local), a survey rate (weighted average rate) or a union average rate (weighted union average rate).

Union Rate Identifiers

A four letter classification abbreviation identifier enclosed in dotted lines beginning with characters other than "SU" or "UAVG" denotes that the union classification and rate were prevailing for that classification in the survey. Example:

PLUM0198-005 07/01/2014. PLUM is an abbreviation identifier of the union which prevailed in the survey for this classification, which in this example would be Plumbers. 0198 indicates the local union number or district council number where applicable, i.e., Plumbers Local 0198. The next number, 005 in the example, is an internal number used in processing the wage determination. 07/01/2014 is the effective date of the most current negotiated rate, which in this example is July 1, 2014.

Union prevailing wage rates are updated to reflect all rate changes in the collective bargaining agreement (CBA) governing this classification and rate.

Survey Rate Identifiers

Classifications listed under the "SU" identifier indicate that no one rate prevailed for this classification in the survey and the published rate is derived by computing a weighted average rate based on all the rates reported in the survey for that classification. As this weighted average rate includes all rates reported in the survey, it may include both union and non-union rates. Example: SULA2012-007 5/13/2014. SU indicates the rates are survey rates based on a weighted average calculation of rates and are not majority rates. LA indicates the State of Louisiana. 2012 is the year of survey on which these classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination. 5/13/2014 indicates the survey completion date for the classifications and rates under that identifier.

Survey wage rates are not updated and remain in effect until a new survey is conducted.

Union Average Rate Identifiers

Classification(s) listed under the UAVG identifier indicate that no single majority rate prevailed for those classifications; however, 100% of the data reported for the classifications was union data. EXAMPLE: UAVG-OH-0010 08/29/2014. UAVG indicates that the rate is a weighted union average rate. OH indicates the state. The next number, 0010 in the example, is an internal number used in producing the wage determination. 08/29/2014 indicates the survey completion date for the classifications and rates under that identifier.

A UAVG rate will be updated once a year, usually in January of each year, to reflect a weighted average of the current negotiated/CBA rate of the union locals from which the rate is based.

WAGE DETERMINATION APPEALS PROCESS

1.) Has there been an initial decision in the matter? This can be:

* an existing published wage determination

* a survey underlying a wage determination

* a Wage and Hour Division letter setting forth a position on a wage determination matter

* a conformance (additional classification and rate) ruling

On survey related matters, initial contact, including requests for summaries of surveys, should be with the Wage and Hour Regional Office for the area in which the survey was conducted because those Regional Offices have responsibility for the Davis-Bacon survey program. If the response from this initial contact is not satisfactory, then the process described in 2.)

and 3.) should be followed.

With regard to any other matter not yet ripe for the formal process described here, initial contact should be with the Branch of Construction Wage Determinations. Write to:

Branch of Construction Wage Determinations Wage and Hour Division U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

2.) If the answer to the question in 1.) is yes, then an interested party (those affected by the action) can request review and reconsideration from the Wage and Hour Administrator (See 29 CFR Part 1.8 and 29 CFR Part 7). Write to:

Wage and Hour Administrator

U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

The request should be accompanied by a full statement of the interested party's position and by any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue.

3.) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative Review Board (formerly the Wage Appeals Board). Write to:

Administrative Review Board U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

4.) All decisions by the Administrative Review Board are final.

END OF GENERAL DECISION

Versico, a division of Carlisle Construction Materials Incorporated, would like to provide a brief overview of its products and capabilities. It is our hope that you will include Versico products in your roofing specification.

Versico was formed in 1993 after the acquisition of Goodyear’s roofing business. Versico manufactures a wide range of EPDM, TPO and PVC single-ply roofing systems, polyisocyanurate and expanded polystyrene insulation boards and offers a full line of accessory products and warranties. Versico products meet or exceed all applicable ASTM standards and offer an industry-leading array of code approvals.

Total System, No Dollar Limit (NDL) warranties are available on systems installed only by Versico Authorized Roofing Contractors and inspected and approved by Versico’s Field Service Representatives. Versico maintains a large warranty reserve; as a division of a publicly held company (NYSE: CSL), this reserve is audited annually for its sufficiency.

We look forward to the inclusion of our products in your project specifications, and stand ready to provide sales and technical assistance when requested. Versico specification binders for EPDM, TPO and PVC are available at no charge and can be ordered using our online Literature and Sample Order form. Versico product information can also be accessed at www.versico.com.

Please do not hesitate to contact me personally, should you have any questions or require more information about our company.

Regards, Frank Palmer General Manager

Overview

Versico’s VersiGard EPDM White membranes are 60-mil (1.52 mm) or 90-mil (2.28 mm) non-reinforced Ethylene Propylene Diene Monomer (EPDM) based elastomeric homogenous roof membranes. This roofing membrane may be used for new single-ply roof construction and re-roofing applications. VersiGard EPDM White 60-mil membranes are available in widths of up to 30' (9 m) and lengths of up to 100' (30 m). VersiGard EPDM White 90-mil membranes are available in widths of up to 10' (3 m) and lengths of up to 100' (30 m). VersiGard EPDM White membranes are ENERGY STAR®*-qualified, can contribute toward LEED® credits and are also compliant with California’s Title 24 cool roof standards for initial and aged solar reflectance and thermal emittance.

Features and Benefits

• Versico EPDM has 25 years of proven performance

• Industry-leading resistance to outdoor weathering with 25,200 kJ/m² total radiant exposure without cracking or crazing

• QAT Seam Technology and full line of Quick-Applied fl ashing accessories greatly enhance workmanship quality by simplifying the contractors’ job

• White EPDM is the smart choice in warmer climates as it helps reduce air conditioning costs

– ENERGY STAR qualifi ed and Cool Roof Rating Council certifi ed

– Reduces carbon footprint by lowering air conditioning costs

• Lifecycle Assessment using EPA’s TRACI model analyzed EPDM, TPO, PVC and Modified-Bitumen

– EPDM had the lowest Global Warming Potential

– EPDM had the lowest Acid Rain impact

– EPDM had the lowest contribution to smog

• Numerous studies and real-world experience confirm that VersiGard’s 540% elongation and weathering resistance result in superior hail damage resistance;

UL 2218 Class 4 rating

• EPDM is the most dimensionally stable heat-resistant membrane and stays flexible even in extremely cold conditions down to -40°F (see Flexibility/Torsion DMA data.)

• Wide array of design choices that are UL and FM approved with standard or Low-VOC adhesives

• 60-mil and 90-mil membranes available for up to 20-and 30-year warranties

• Versico manufactures all the major components of a typical roofing system including membrane, flashings, tapes, adhesives, sealants, insulations and insulating cover boards

Versico’s QAT Seam Technology

With Versico’s Quick-Applied Tape (QAT) Seam technology, most of the labor to create seams between membrane panels is completed in a quality-controlled, state-of-the-art environment. This process results in a reliable seam with greater peel and sheer strengths and with no entrapped air bubbles. Consistent placement of the QAT also maximizes the splice area and results in a high-quality seam. Versico’s QAT is available on all VersiGard White membranes up to 30’ (9 m) in width, providing the fastest way to complete a seam in today’s roofing market.

Installation

VersiGard EPDM White membrane is primarily utilized in Fully Adhered Roofing Systems.

Fully Adhered Roofing System: Insulation is mechanically attached or adhered to the roof deck. The substrate and membrane are coated with Versico EPDM Bonding Adhesive. The membrane is then rolled into place and broomed down. To complete seams between two adjoining membrane panels, apply primer to the splice

VERSIGARD®

EPDM WHITE MEMBRANES

T E C H N I C A L D A T A B U L L E T I N

A S I N G L E S O U R C E F O R S I N G L E - P LY R O O F I N G

Vers ico, PO Box 1289, Car l i s le, PA 17013 Te l : 800.992 .7663 Fax : 717.96 0.4 036 Web : www.vers ico.com area in conjunction with Versico’s QAT. As an alternative, Versico’s hand-applied QA Seam Tape may be used.

For cold weather splicing below 40°F (5°C), these steps must be followed:

• Heat the primed area of the bottom membrane with a hot-air gun as the top sheet with QAT is applied and pressed into place.

• Prior to rolling the splice area with a 2"-wide steel hand roller apply heat to the top side of the membrane with a hot-air gun. The heated surface should be hot to the touch. Be careful not to burn or blister the membrane.

REVIEW VERSICO’S SPECIFICATIONS AND DETAILS FOR

SPECIFIC INSTALLATION REQUIREMENTS.

Precautions

1. Sunglasses that filter out ultraviolet light are strongly recommended as the white surface intensifies sunlight through reflection.

2. White surfaces reflect heat and may become slippery due to frost and ice build-up. Exercise extreme caution during cold conditions to prevent falls.

3. Care must be exercised when working close to a roof edge when surrounding area is snow covered as roof edge may not be clearly visible.

4. Use proper stacking procedures to ensure sufficient stability of the materials.

5. Exercise caution when walking on wet membrane.

Membranes are slippery when wet.

6. Membranes with QAT should not be exposed to prolonged jobsite storage temperatures in excess of 90ºF (32ºC), otherwise the shelf life of the QAT may be affected.

7. When VersiGard EPDM White Membrane with QAT is used, shade the tape end of the rolls until ready to use in warm, sunny weather.

TYPICAL PROPERTIES AND CHARACTERISTICS

Property Test Method SPEC. (Pass) Typical

Tolerance on nominal thickness, % ASTM D412 ± 10 ± 10

Weight, lbm/ft2 (kg/m2) 60-mil 90-mil

0.37 (1.8)

0.60 (2.9)

Tensile Strength, min, psi (Mpa) ASTM D412 1305 (9) 1465 (10.1)

Elongation, Ultimate, min, % ASTM D412 300 540

Tear Strength, min, lbf/in (kN/m) ASTM D624 (Die C)

150 (26.3) 187 (32.7)

Factory Seam Strength, min Modifi ed

ASTM D816

Membrane Rupture

Membrane Rupture

Resistance to Heat Aging* Properties after 28 days @ 240ºF (116ºC) Tensile Strength, min, psi (Mpa) Elongation, Ultimate, min, % Tear Strength, min, lbf/in (kN/m) Linear Dimensional Change, max, %

ASTM D573

ASTM D412

ASTM D412

ASTM D624

ASTM D1204

1205 (8.3) 125 (21.9) ± 1.0

1345 (9.3) 185 (32.4) -0.2

Ozone Resistance* Condition after exposure to 100 pphm Ozone in air for 168 hours @ 104ºF (40ºC) Specimen is at 50% strain

ASTM D1149 No Cracks No Cracks

Brittleness Temp., max, ºF (ºC)* ASTM D746 -49 (-45) -67 (-55) Resistance to Water Absorption* After 7 days immersion @ 158ºF (70ºC) Change in mass, max, %

ASTM D471 +8, -2 +3.3

Water vapor Permeance* Max, perms

ASTM E96

(Proc. B or BW)

0.10 0.02

Flexibility/Torsion DMA ASTM D5279-08 N/A 55 MPa @ -40°F

Fungi Resistance ASTM G21 N/A 0 (No Growth)

Resistance to Outdoor (Ultraviolet) Weathering* Xenon-Arc, total radiant exposure at 0.70 W/m2 irradiance, 80ºC black panel temp.

ASTM D4637

Conditions

No Cracks No Crazing 7,560 kJ/m² 3,000 hrs

No Cracks No Crazing 25,200 kJ/m² 10,000 hrs

At 0.35 W/m² irradiance, 80°C black panel temperature

6,000 hrs 20,000 hrs

*Not a Quality Control Test due to the time required for the test or the complexity of the test.

However, all tests are run on a statistical basis to ensure overall long-term performance of the sheeting.

Typical properties and characteristics are based on samples tested and are not guaranteed for all samples of this product. This data and information is intended as a guide and does not refl ect the specifi cation or specifi cation range for any particular property of this product.

Note: VersiGard White non-reinforced EPDM membrane meets or exceeds the minimum requirements set forth by ASTM D 4637 for Type I non-reinforced EPDM single-ply roofi ng membranes.

VersiGard Product Data Sheet. 05/11 © 2011 Versico. Versico, VersiGard and the Versico logo are trademarks of Versico.

LEED is a registered trademark of the U.S. Green Building Council.

T E C H N I C A L D A T A B U L L E T I N

RADIATIVE PROPERTIES FOR ENERGY STAR,

COOL ROOF RATING COUNCIL (CRRC) AND LEED

Property Test Method White EPDM

ENERGY STAR –

Initial solar refl ectance

Solar Spectrum Refl ectometer

0.76

ENERGY STAR –

Solar refl ectance after 3 years

Solar Spectrum Refl ectometer (after cleaning)

0.64

CRRC initial solar refl ectance ASTM C1549 0.76

CRRC solar refl ectance after 3 years ASTM C1549 (uncleaned) 0.64

CRRC initial thermal emittance ASTM C1371 0.90

CRRC thermal emittance after 3 years ASTM C1371 (uncleaned) 0.87

LEED thermal emittance ASTM E408 0.91

SRI (Solar Refl ectance Index) ASTM E1980 94

LEED INFORMATION

Pre-consumer Recycled Content 0% Post-consumer Recycled Content 0% Manufacturing Location(s) Carlisle, PA

Solar Refl ective Index 94

© 2014 Versico. 06.12.14 Versico, VersiGard and the Versico logo are trademarks of Versico. LEED is a registered trademark of the U.S. Green Building Council.

ENERGY STAR is a registered trademark owned by the U.S. Government. *ENERGY STAR qualifi cation is only available in the U.S.

OWNER:

BUILDING :

DATE INSTALLATION COMPLETED :

Versico, a division of Carlisle Construction Materials Incorporated (Versico), warrants to the Building Owner (Owner) of the building described below, that subject to the terms, conditions, and limitations stated in this warranty, Versico will repair any leak in the Versico Total Roofing System (Versico Total Roofing System) installed by a Versico Authorized Roofing Contractor for a period of years commencing with the date of Versico's acceptance of the Versico Total Roofing System installation. However, in no event shall Versico's obligations extend beyond years subsequent to the date of substantial completion of the Versico Total Roofing System. See below for exact date of warranty expiration.

The Versico Total Roofing System is defined as the following Versico brand Materials: Membrane, Flashings, Adhesives and Sealants, Insulation, Cover Boards, Fasteners, Fastener Plates, Fastening Bars, Metal Work, Insulation Adhesives, and any other Versico brand products utilized in this installation.

TERMS, CONDITIONS, LIMITATIONS

1. Owner shall provide Versico with written notice via letter, fax or email within thirty (30) days of the discovery of any leak in the Versico Total Roofing System. Owner should send written notice of a leak to Versico's Warranty Services Department at the address set forth at the bottom of this warranty. By so notifying Versico, the Owner authorizes Versico or its designee to investigate the cause of the leak. Should the investigation reveal the cause of the leak to be outside the scope of this Warranty, investigation and repair costs for this service shall be paid by the Owner.

2. If, upon inspection, Versico determines that the leak is caused by defects in the Versico Total Roofing System's materials, or workmanship of the Versico Authorized Roofing Contractor in installing the same, Owner's remedies and Versico's liability shall be limited to Versico's repair of the leak.

3. This Warranty shall not be applicable if, upon Versico's inspection, Versico determines that any of the following has occurred:

(a) The Versico Total Roofing System is damaged by natural disasters, including, but not limited to, lightning, fire, insect infestations, earthquake, tornado, hail, hurricanes, and winds of (3 second) peak gust speeds of mph or higher measured at 10 meters above ground, or

(b) Loss of integrity of the building envelope and, or structure including, but not limited to partial or complete loss of roof decking, wall siding, windows, doors or other envelope components or from roof damage by wind-blown objects, or:

(c) The Versico Total Roofing System is damaged by any intentional or negligent acts, accidents, misuse, abuse, vandalism, civil disobedience, or the like.

(d) Deterioration or failure of building components, including, but not limited to, the roof substrate, walls, mortar, HVAC units, non-Versico brand metal work, etc., occurs and causes a leak, or otherwise damages the Versico Total Roofing System; or

(e) Acids, oils, harmful chemicals and the like come in contact with the Versico Total Roofing System and cause a leak, or otherwise damage the Versico Total Roofing System.

(f) The Versico Total Roofing System encounters leaks or is otherwise damaged by condensation resulting from any condition within the building that may generate moisture.

WARRANTY EXPIRATION DATE :

VERSICO TOTAL ROOFING SYSTEM WARRANTY

4. This Warranty shall be null and void if any of the following shall occur:

(a) If, after installation of the Versico Total Roofing System by a Versico Authorized Roofing Contractor, there are any alterations or repairs made on or through the roof or objects such as, but not limited to, structures, fixtures, solar panels, wind turbines, roof gardens or utilities are placed upon or attached to the roof without first obtaining written authorization from Versico;

or

(b) Failure by the Owner to use reasonable care in maintaining the roof, said maintenance to include, but not be limited to, those items listed on Versico's Care & Maintenance Information sheet which accompanies this Warranty.

5. Only Versico brand insulation products are covered by this warranty. Versico specifically disclaims liability, under any theory of law, for damages sustained by or caused by non-Versico brand insulation products.

6. During the term of this Warranty, Versico shall have free access to the roof during regular business hours.

7. Versico shall have no obligation under this Warranty while any bills for installation, supplies, services, and warranty charges have not been paid in full to the Versico Authorized Roofing Contractor, Versico, or material suppliers.

8. Versico's failure at any time to enforce any of the terms or conditions stated herein shall not be construed to be a waiver of such provision.

9. Versico shall not be responsible for the cleanliness or discoloration of the Versico Total Roofing System caused by environmental conditions including, but not limited to, dirt, pollutants, or biological agents.

10. Versico shall have no liability under any theory of law for any claims, repairs, restoration, or other damages including, but not limited to, consequential or incidental damages relating, directly or indirectly, to the presence of any irritants, contaminants, vapors, fumes, molds, fungi, bacteria, spores, mycotoxins, or the like in the building or in the air, land, or water serving the building.

11. This warranty shall be transferable upon a change in ownership of the building when the owner has completed certain procedures including a transfer fee and an inspection of the Roofing System by a Versico representative.

VERSICO DOES NOT WARRANT PRODUCTS UTILIZED IN THIS INSTALLATION

WHICH IT HAS NOT FURNISHED; AND SPECIFICALLY DISCLAIMS LIABILITY, UNDER

ANY THEORY OF LAW, ARISING OUT OF THE INSTALLATION AND PERFORMANCE

OF, OR DAMAGES SUSTAINED BY OR CAUSED BY, PRODUCTS NOT FURNISHED

BY VERSICO OR THE PRIOR EXISTING ROOFING MATERIAL OVER WHICH THE

VERSICO ROOFING SYSTEM HAS BEEN INSTALLED

THE REMEDIES STATED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES FOR

FAILURE OF THE VERSICO TOTAL ROOFING SYSTEM OR ITS COMPONENTS.

THERE ARE NO WARRANTIES EITHER EXPRESSED OR IMPLIED, INCLUDING THE

IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND

MERCHANTABILITY, WHICH EXTEND BEYOND THE FACE HEREOF. VERSICO

SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR OTHER

DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR DAMAGE TO

THE BUILDING OR ITS CONTENTS UNDER ANY THEORY OF LAW.

VSW-1

P.O. Box 1289 Carlisle, PA 17013

(800) 992-7663 (717) 960-4035 FAX

ROOFER:

WARRANTY NUMBER:

VERSICO, a division of Carlisle Construction Materials Incorporated

BY

DATE OF ACCEPTANCE BY VERSICO :

Rev 01/15

A SINGLE SOURCE

FOR SINGLE-PLY ROOFING

VERSICO WAS FORMED THROUGH THE ACQUISITION OF

A MAJOR SINGLE-PLY ROOFING MANUFACTURER IN 1993.

SINCE THAT TIME, VERSICO HAS POSITIONED ITSELF AS ONE

OF THE TOP SINGLE-PLY ROOFING SYSTEM SUPPLIERS BY

CLEARLY FOCUSING ITS EFFORTS ON QUALITY PRODUCTS

AND EXCEPTIONAL SERVICE.

Versico has a wide range of single-ply roofi ng systems to meet almost any building design. Versico has the ability to solve all of your roofi ng needs with our VersiGard® EPDM Roofi ng Systems and our

VersiWeld® TPO and VersiFlex™ PVC Heat-Weldable

Roofi ng Systems.

All systems offer a full line of accessory products and insulation. Because each project has its own individual requirements, choosing the right roof is only part of the total solution. Selection of the appropriate attachment method, assisted by

Versico’s Systems Design & Review Department, ensures every Versico roof will provide the protection and value it is designed to deliver. Depending on the membrane and application, a Versico

Roofi ng System can be warranted for up to 30 years when installed by a Versico Authorized Roofi ng

Contractor. After the warranty is issued, Versico’s

Warranty Services Department is a phone call away to provide customer satisfaction throughout the life of the roof.

VersiGard Black non-reinforced EPDM membranes are available in 45-mil, 60-mil and 90-mil thicknesses.

Membrane widths up to 50' and lengths to 200' afford less rooftop seaming for large projects. Custom sizes may also be requested.

VersiGard (Black) reinforced membranes, in 45-, 60- and 75-mil thicknesses, are manufactured with a polyester reinforcement completely encapsulated between two plies of EPDM. Specially developed for Versico’s Mechanically Attached Systems, Metal Retrofi t and Fully Adhered Systems, the membrane offers superior fatigue and puncture resistance.

VersiGard (White) non-reinforced membrane, in 60-mil and 90-mil thicknesses is available in 10' widths and 50' and 100' lengths, which helps to reduce seams and minimize installation costs. It has UL Class A, B and Universal Slope ratings available over most deck types. It also meets ENERGY STAR® guidelines and is environmentally friendly.

GARD

ROOFING SYSTEMS

BALLASTED

Ballasted designs combine a loose-laid insulation and membrane and the use of ballast or pavers as securement.

FULLY ADHERED

Fully Adhered Systems require mechanical or adhesive attachment of the insulation and bonding of the membrane to the insulation.

MECHANICALLY

ATTACHED

Mechanically Attached Systems require mechanical attachment of the insulation to the deck and mechanical attachment of the membrane within the seam area.

WARRANTY OPTIONS FOR VERSIGARD ROOFING SYSTEMS

• Up to 30-year No Dollar Limit Total Roofi ng System Warranties are available. Standard wind speed coverage is 55 mph.

Additional wind speed warranties are available.

• A warranted system is installed by an authorized Versico roofi ng contractor. Once completed, a warranted system is inspected by a trained Versico Field Service Representative to ensure conformance with Versico specifi cations.

Note: For technical specifi cations, consult individual system sell sheets or technical data bulletins.

VersiGard with Quick-Applied Tape (QAT) seam technology is available on both black and white EPDM membranes. Applied in a factory setting, QAT saves up to 75% in labor costs and provides higher-strength, more uniform seams.

VersiWeld Roofi ng Systems incorporate 45-mil, 60-mil, or 80-mil Thermoplastic Polyolefi n (TPO) membrane.

Versico’s VersiWeld membrane is comprised of three layers —a TPO polymer base, a strong, polyester-reinforced fabric center (scrim) and a tough, thermoplastic polyolefi n compounded top ply. Because the top ply is the most vital membrane component for long-term weathering characteristics, Versico manufactures its membranes with an industry-leading thicker and smoother top ply over scrim. The relatively smooth surface produces a total surface fusion weld that creates a consistent, watertight and monolithic roof assembly.

VersiFleece® TPO membrane incorporates VersiWeld TPO membrane laminated to a non-woven fl eece backing.

It is available with standard fl eece in 100-, 115- and 135-mil total thicknesses and with Asphalt-Compatible(AC) fl eece in 120-, 135- and 155-mil total thicknesses.

Standard VersiFleece TPO can be adhered using DASH™ or AquaBase 120 adhesive and VersiFleece AC can be adhered using hot asphalt or Versico’s Cold-Applied Adhesive.

ROOFING SYSTEMS

VersiWeld QA (Quick-Applied) TPO offers a factory-applied adhesive formulation that provides superior adhesion, preventing membrane expansion. VersiWeld QA TPO combines the energy efficiency and durable characteristics that VersiWeld TPO consistently provides with the easiest, quickest and most consistent TPO installation in the industry.

WELD

FULLY ADHERED

VersiWeld Fully Adhered Roofi ng Systems begin with insulation mechanically attached or adhered to the roof deck. The membrane and substrate are then coated with bonding adhesive. Then the membrane is rolled into place and seams are hot-air welded.

MECHANICALLY

ATTACHED

VersiWeld Mechanically Attached Roofi ng Systems start with insulation fastened to the substrate. VersiWeld membrane is then fastened through the insulation with fasteners and plates. (Consult the Versico Fasteners & Plates Sell Sheet.)

Adjoining membrane sheets are then overlapped and hot-air welded.

All VersiWeld TPO membranes feature OctaGuard XT, a time-tested weathering package that is comprised of eight performance-enhancing ingredients with three heat-stabilizing antioxidants and three UV absorbers that help protect Versico’s TPO membranes and dramatically improve their ability to resist deterioration due to the effects of weather.

WARRANTY OPTIONS FOR VERSIWELD & VERSIFLEX SYSTEMS

• Up to 30-year No Dollar Limit Total Roofi ng System Warranties are available. Standard wind speed coverage is 55 mph.

Additional wind speed warranties are available.

• A warranted system must be installed by an authorized Versico roofi ng contractor.

• Once completed, a warranted system is inspected by a trained Versico Field Service Representative to ensure conformance with Versico specifi cations.

Note: For technical specifi cations, consult individual system sell sheets or technical data bulletins.

VersiFlex Roofing Systems incorporate 50-mil, 60-mil or 80-mil Polyvinyl Chloride (PVC) membranes.

Versico’s VersiFlex Membrane is comprised of three layers—a PVC polymer bottom ply; a strong, reinforced fabric center (scrim) and a tough, thermoplastic PVC-compounded top ply. VersiFlex is specifi cally designed for long-term performance and is produced with the strictest quality control measures providing end users and owners the most consistent and reliable PVC product on the market today.

VersiFleece PVC membrane incorporates White VersiFlex PVC membrane laminated to a standard 5.5-oz non-woven fl eece. VersiFleece PVC is available in 115- and 135-mil total thicknesses, providing long-term protection from the elements.

ROOFING SYSTEMS

FULLY ADHERED

The VersiFlex Fully Adhered Roofing System begins with insulation mechanically attached or adhered to the roof deck. The membrane and substrate are then coated with bonding adhesive. Then the membrane is rolled into place and seams are hot-air welded.

MECHANICALLY

ATTACHED

VersiFlex Mechanically Attached Roofing Systems start with insulation fastened to the substrate. VersiFlex membrane is then fastened through the insulation with fasteners and plates. (Consult the Versico Fasteners & Plates Sell Sheet.)

Adjoining membrane sheets are then overlapped and hot-air welded.

VersiFlex-E KEE is manufactured using DuPont™

Elvaloy KEE, a resin modifier that provides long-term flexibility, improved UV resistance and exceptional weathering performance.

Enhanced durability makes VersiFlex-E KEE ideal for applications in which the membrane may be exposed to harsh chemicals and conditions such as acid rain or grease.

INSULATION

Versico Polyiso products consist of state-of-the-art polyiso foam with superior fi re performance characteristics and the ability to retain high R-values ranging from 6.0 to

25.0. Versico Polyiso is manufactured with exceptional

strength, using dimensionally stable facers, which add durability to the boards for long-term performance.

Versico’s Expanded Polystyrene (EPS) Insulation is a rigid formed plastic with resilient closed cells, molded in a range of densities, sizes and profi les to meet specifi cation requirements. EPS exhibits low thermal conductivity, high strength-to-weight ratio and energy effi cient properties.

EPS is available in fl at and tapered boards.

POLYISO INSULATION

EPS INSULATION

• MP-H

• MP-HWF Wood Fiber Board

• MP-HNB Nail Board

• SecurShield

• SecurShield CD

• SecurShield HD

• SecurShield HD Plus

• SecurShield HD Composite

• SecurShield HD EPS Composite

• Tapered Extended Panels

• Pre-Cut Hips & Valleys

• R-Tech Fanfold

• Insulfoam SP

• Insulfoam DB Drainage Board

• SecurShield HD EPS Composite

SYSTEM ACCESSORIES

VersiGard Quick-Applied (QA) self-adhesive accessories greatly reduce the time required for completing seams and installing fl ashing, which can minimize your labor costs.

Because adhesive thickness is controlled in the factory, waste and total material costs are also reduced. The adhesive application is uniform throughout the installation, and the ultimate adhesive strength of VersiGard QA accessories is achieved in a short period of time.

Versico offers a full line of adhesives and sealants for EPDM, TPO and PVC roofi ng systems. All of Versico’s adhesives and sealants are manufactured according to a time-tested, quality-assured formulation. From Cut- Edge Sealant to Low-VOC Bonding Adhesive, Versico offers a wide range of environmentally and user-friendly adhesives and sealants.

VERSIGARD QA ACCESSORIES

VERSICO ADHESIVES & SEALANTS

• QA Pipe Seals

• QA Flashing

• QA Inside/Outside Corners

• QA Coverstrip

• QA Walkway Pads

• QA RTS

• QA Pourable Sealer Pockets

• QA Seam Tape

Versico’s Certifi ed Fabricated Accessories provide enhanced time and cost savings for TPO and PVC installations. These easy-to-install, heat-weldable, pre-fabricated accessories are ideal for virtually any thermoplastic application and provide an economical solution to fi eld fabrication in both standard and custom hard-to-fl ash situations. Certifi ed Fabricated Accessories are the only factory-fabricated accessories that meet the stringent quality tolerances required to be included in a Versico warranted roofi ng system.

THERMOPLASTIC TPO/PVC ACCESSORIES

• Molded Sealant Pockets

• Molded Pipe Seals

• Square Tubing Wraps

• Curb Wrap Corners

• Inside/Outside Corners

• Split Pipe Seals

CONTRACTOR PROGRAMS

Versico’s Contractor Training Workshop is a two-day training course designed for contractors who have applied to become Authorized Versico Contractors. Training sessions are also benefi cial for approved contractors who wish to have additional employees trained.

The workshop offers education to roofi ng contractor personnel on Versico’s products and roofi ng systems.

Seminars provide a balanced approach to training, using both classroom activities along with ample opportunities for hands-on practice, and cover the installation of EPDM and heat-weldable systems.

A quality product installed by a reliable Authorized Contractor is the key to any successful single-ply roofi ng system. Versico prides itself on being able to offer both.

Versico will continue to recognize, on an annual basis, those contractors who consistently provide exceptional service and installations by presenting them with the Versico Gold Medal Quality Award. A Versico Gold Medal Quality Contractor must meet the highest standards including quality, consistency and proven performance.

For additional information refer to the Gold Medal Quality Program located on the website.

CONTRACTOR TRAINING WORKSHOP GOLD MEDAL QUALITY PROGRAM

© 2013 Versico. Printed in U.S.A. Versico, VersiGard, VersiWeld, VersiFlex and the Versico logo are registered trademarks of Versico.

602467 - Versico Capabilities Brochure - 05.30.13 Elvaloy is a registered trademark of DuPont. ENERGY STAR is a registered trademark owned by the U.S. Government.

A S I N G L E S O U R C E F O R S I N G L E - P LY R O O F I N G

Vers ico, PO Box 1289, Car l i s le, PA 17013 Te l : 800.992 .7663 Fax : 717.96 0.4 036 Web : www.vers ico.com