MEO_E2091.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

E 2091 Apr 11, 2017 8

IUID Parts Marking Updates to WP 0009 00 Manifold, Hydraulic System Accessories, Primary and Utility P/Ns 266500-1003/-1005/-1007/-1009 266600-1003, 266600-1005/-1007/-1009

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

4) Normal - Can be implemented with normal priorityPRIORITY IMPLEMENTATION CATEGORY

AH64 DAA

TN 167826 11/3/2016

DMWR 1-4730-390 DATED 31 MAY 2016

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Changes based on DMWR MEO IUID Review (TN 167439). Implement MEO's E2090, E2091, E2092 and E2093 concurrently.

TRAN.TRI.PHA

N.1259782909

Digitally signed by

TRAN.TRI.PHAN.1259782909

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=TRAN.TRI.PHAN.1259782909 Date: 2017.01.26 13:53:17 -06'00'

FERGUSON.WA

DE.RANDALL.13

79892597

Digitally signed by

FERGUSON.WADE.RANDALL.1379892597

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=FERGUSON.WADE.RANDALL.137989259 Date: 2016.12.12 08:43:21 -06'00'

Wade Ferguson

NOLL.GERALD.S

TEVEN.12311769

Digitally signed by

NOLL.GERALD.STEVEN.1231176922

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=NOLL.GERALD.STEVEN.1231176922 Date: 2017.01.26 15:12:41 -06'00'

Tri Tran G Steve Noll PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

0018 00

00-1

REPLACE: "Title page, Initial Setup and REPAIR OR REPLACEMENT/ Item Unique Identification (IUID) Data Plate steps 1 thru 5" with new "Title page, Initial Setup, Item Unique Identification (IUID) Data Plate REPLACEMENT and Item Unique Identification (IUID) Data Plate FABRICATION found on pages 2 and 3 of this MEO.

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

MED FORM 30 AUG 2016

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

DMWR 1-4730-390 0018 00

DEPOT MAINTENANCE

MANIFOLD, HYDRAULIC SYSTEM ACCESSORIES, PRIMARY

PART NO. 266500

ITEM UNIQUE IDENTIFICATION (IUID) DATA PLATE REPLACEMENT / FABRICATION

INITIAL SETUP:

Tools and Special Tools Materials/Parts (cont.)

Data Matrix Grader/Verifier or equivalent Epoxy Coating (WP 0157 00, Item 29) (WP 0014 00, Table 1, Item 53) Isopropyl alcohol (WP 0157 00, Item 24) Data Matrix Reader or equivalent Laminate Film (WP 0157 00, Item 30) (WP 0014 00, Table 1, Item 52) Polyurethane Coating (WP 0157 00, Item 31) CO2 Laser Etch or a Metal Photographic Process Sealing Compound (WP 0157 00, Item 32) (WP 0014 00, Table 1, Item 51) TESA Tape (WP 0157 00, Item 28)

Materials/Parts References Abrasive paper (WP 0157 00, Item 27) WP 0009 00, CHECKING ATTACHED Brush (WP 0157 00, Item 26) DOCUMENTS Catalyst 683-3-20 Base X-310A MIL-STD-130 (WP 0157 00, Item 25) MIL-DTL-15024 Cloth (WP 0157 00, Item 4)

Item Unique Identification (IUID) Data Plate REPLACEMENT

Figure 1 shows the possible IUID data plate format options for this Primary Hydraulic System Accessories Manifold.

Option A the manufacturer IUID data plate format represents components originally UID-marked during production.

Option B the legacy IUID data plate format represents components originally UID-marked post-production during an M&O event or in the field (commonly referred to as legacy components).

1. Manufacturer IUID Data Plate. The manufacturer 2-D data matrix is encoded with a Construct 2 UII using TEIs data qualifiers MFR (manufacturer's CAGE code), PNO (original part number) and SER (manufacturer's serial number).

2. Legacy IUID Data Plate. The legacy 2-D data matrix is encoded with a Construct 1 or Construct 2 UII using TEIs SPL (supplier's CAGE code) and UCN (supplier's unique component number) or 7L (DODAAC Enterprise Identifier), 1P (original part number) at the time the component was marked and S (manufacturer serial number), as applicable.

3. Option A and Option B: In addition to the UII, the 2-D data matrix shall be encoded with the current Boeing part number using TEI's PNR (current Part Number) as the data qualifier. The PNR is the component's current Boeing part number upon completion of the M&O event. For Legacy Construct 2, 30P application refer to Figure 2. Primary OPM IUID Data Plates Examples.

MED FORM 24 FEB 2016

Attac2091

Continuation Sheet

Item Unique Identification (IUID) Data Plate Fabrication

NOTE

Prior to fabrication of the IUID data plate, the DoD IUID Registry shall be queried WP 0009 00.

NOTE

The UII shall be formatted/constructed IAW DoD Guide to Uniquely Identifying Items and MIL-STD-130. The part shall be registered in the DoD IUID Registry.

1. If required to add or replace the IUID data plate per WP 0009 00, fabricate a new IUID data plate (Figure1) The MRI and HRI shall be marked on the IUID data plate using a Laser Etch (WP 0014 00, Table 1, Item

51) or a Metal Photographic Process or equivalent and font requirements IAW MIL-STD-130. The IUID data plate is fabricated of photosensitive anodized aluminum plate that meets the physical characteristics per MIL-DTL-15024. As an alternate, TESA Tape is an acceptable material marked with a laser, thermal transfer printer, or an acceptable technique IAW MIL-STD-130.

2. Using a data matrix grader/verifier (WP 0014 00, Table 1, Item 53) or an equivalent, verify that the MRI 2-D data matrix has a minimum print quality passing grade per parameters specified in MIL-STD-130 or per the exceptions noted in Table 1 for laser etched black anodize. If the 2-D data matrix failed minimum print quality grade, repeat the marking process until minimum print quality grade is achieved. Record the IUID data plate 2-D data matrix grade when required.

MED FORM 24 FEB 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

00-4

00-5

00-6 00-7 00-8

Table 1.

Figure 1.

Figure 2.

Figure 3.

CHANGE in "Overcoat Application - CO2 Laser Etch Black Anodized Aluminum, Step 1." in the first sentence "683-3-2" to read: "683-3-20"

REPLACE: "Table 1" with new "Table 1" found on page 5 of this MEO.

REPLACE: "Figure1, Figure 2 and Figure 3" with new "Figure 1 and Figure 2" found on pages 6 thru 8 of this MEO.

MED FORM 24 FEB 2016

Continuation Sheet

Table 1. VERIFICATION REQUIREMENTS

PARAMETERS LASER ETCH ANODIZE

Exceptions to ISO/IEC 15415:

Symbol Contrast Modulation Grade A1

All Other Characteristics Grade B or better Exceptions to SAE AS9132:

Symbol Contrast Module Fill 85% to 115% Angular Deviation < 2° Metallurgical Eval - Destruct Test None

1 Modulation to be Grade A for uncoated labels; may be Grade B for clear coated labels.

MED FORM 24 FEB 2016

Continuation Sheet

IUID Data Plate Material:

1. 1.00” x 2.25” aluminum alloy foil per ASTM B209, thickness .005” with adhesive backing 3M transfer tape, 9485 PC, .005” thick, Finish:

Black anodize per Mil-A-8623, Type II, Class 2.

2. For metal Photographic process: use photosensitive anodized aluminum alloy GG-P 455, Type 1, Class 1 Grade A.

Drawing Notes:

1. Quite Zone (Free Space) around the 2-D data matrix code shall .050” MIN. in all directions.

2. The recommended part mark size for the 2-D data matrix symbol is .025” to 0.50” square. The 2-D Data Matrix Symbol shall not be larger than 1” Square.

3. If the component arrives with a Manufacture IUID data plate as shown or other IUID Label media and the UII is registered, it shall be replicated (to the configuration/format found at PSA) when replacement is necessary due to damage and/or change to component data (e.g., part number roll).

Parker CONTROL SYSTEMS DIVISION

IRVINE, CALIFORNIA 92618

MANIFOLD, PRIMARY

PARKER PN 266500-100X REV U

MFR 82106

PNO 266500-100X

SEQ 12345

PNR 7-211810012-X

FLUID MIL-PRF-83282 3000 PSI

Parker CONTROL SYSTEMS DIVISION

IRVINE, CALIFORNIA 92618

MANIFOLD, PRIMARY

PARKER PN 266500-100X REV U

MFR 82106

PNO 266500-100X

SEQ 12345

PNR 7-211810012-X

FLUID MIL-PRF-83282 3000 PSI

2.25”

.050” MIN QUIET ZONE IN

ALL DIRECTIONS

1.00”

MANFACTURER IUID DATA PLATE

OPTION A

Figure 1. Primary Manifold IUID Data Plate (Sheet 1 of 2).

MED FORM 24 FEB 2016

Continuation Sheet

IUID Data Plate Material:

1. .60” X 2.50” aluminum sheet, 1100 aluminum alloy per ASTM B209. Thickness: .012”, with adhesive backing 3M transfer tape, 9485 PC, .005” thick.

Finish:

Black anodize per MIL-A-8625, Type II, Class 2.

2. For Metal Photographic Process: Use photosensitive anodized aluminum alloy per GG-P-455, Type I, Class 1, Grade A.

Alternative Material:

3. .60” x 2.50” TESA Tape, Tesa Secure 6973 PV6, matte black top layer with white under layer (WP 0157 00, Item 28)

Drawing Notes:

1. Quiet Zone (Free Space) around the 2-D data matrix code shall be .050” MIN. in all directions.

2. The recommended part mark size for the 2-D data matrix symbol is .25” to .50” square. The 2-D data matrix symbol shall not be larger than 1” square.

3. If the component arrives without a registered UII, a Legacy IUID data plate shall be fabricated in the format as shown. The 2-D data matrix shall contain a Construct 1 UII using TEIs SPL and UCN as data qualifiers. The 2-D data matrix shall also contain the component’s PNR as additional information.

SPL

UCN

PNR

.60 IN.

2.50 IN.

.050 IN. MIN QUIET ZONE IN ALL

DIRECTIONS

SPL

UCN

PNR

LEGACY IUID DATA PLATE

OPTION B

Figure 1. Primary Manifold IUID Data Plate (Sheet 2 of 2).

MED FORM 24 FEB 2016

Continuation Sheet

DODAAC: W81N8L

PNO: 7-211810013-7

SER: 012129-1234

DODAAC: W80N3L

PNO: 7-211810012-7

SER: 012129-XXXX

OPM IUID DATA PLATES EXAMPLES

7L: XXXXXX

1P: 266500-100X

S: XXXXXX-XXXX

30P: 7-218810013-X

7L: XXXXXX

1P: XXXXXXXXX

S: XXXXXX-XXXX

30P: 7-218810012-X

2.50 IN.

.060 IN.

NOTES:

1. OPM IUID data plates may vary in size, shape and material.

2. The 2-D data matrix contains a Construct II UII using Data Identifiers (DIs) as data qualifiers.

3. Primary Hydraulic System Accessory Manifolds that have an OPM IUD data plate installed, shall be removed and replaced by either legacy IUID data plate as shown above, using the UII data that is encoded in the OPM IUID data plate 2-D data matrix and that have been recorded in the DoD IUID Registry, as applicable.

4. Materials and application same as Figure 1, Sheet 2 of 2.

5. The 30P is only encoded in the 2-D data matrix and displayed as HRI and when the original part number 1P changes with a new configuration, i.e. part number roll (dash number change).

DODAAC: WXXXXX

PNO: 7-211810012-X

SER: 012129-XXXX

DODAAC: W80N3L

PNO: 266500-1009

SER: 012129-XXXX

7L: XXXXXX

1P: 7-218810012-X

S: XXXXXX-XXXX

30P: 7-218810013-X

OR

Figure 2. Primary OPM IUID Data Plates Examples.

MED FORM 24 FEB 2016