W56HZV15R0095-0001_PADDS.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. Contract ID Code Page Of

2. Amendment/Modification No.

3. Effective Date

4. Requisition/Purchase Req No.

5. Project No. (If applicable)

6. Issued By Code 7. Administered By (If other than Item 6) Code

8. Name And Address Of Contractor (No., Street, City, County, State and Zip Code)

9A. Amendment Of Solicitation No.

9B. Dated (See Item 11)

10A. Modification Of Contract/Order No.

10B. Dated (See Item 13) Code Facility Code

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in item 14. The hour and date specified for receipt of Offers is extended, is not extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing items 8 and 15, and returning ____________ copies of the amendments: (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. Accounting And Appropriation Data (If required)

13. THIS ITEM ONLY APPLIES TO MODIFICATIONS OF CONTRACTS/ORDERS

It Modifies The Contract/Order No. As Described In Item 14.

A. This Change Order is Issued Pursuant To: The Changes Set Forth In Item 14 Are Made In

The Contract/Order No. In Item 10A.

B. The Above Numbered Contract/Order Is Modified To Reflect The Administrative Changes (such as changes in paying office, appropriation data, etc.) Set

Forth In Item 14, Pursuant To The Authority of FAR 43.103(b).

C. This Supplemental Agreement Is Entered Into Pursuant To Authority Of:

D. Other (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return _______________ copies to the Issuing Office.

14. Description Of Amendment/Modification (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. Name And Title Of Signer (Type or print)

16A. Name And Title Of Contracting Officer (Type or print)

15B. Contractor/Offeror 15C. Date Signed 16B. United States Of America 16C. Date Signed

By (Signature of person authorized to sign) (Signature of Contracting Officer)

NSN 7540-01-152-8070

PREVIOUS EDITIONS UNUSABLE

30-105-02 STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA FAR (48 CFR) 53.243

SEE SCHEDULE

X

Firm Fixed Price

0001 2016AUG05

W56HZV

U.S. ARMY CONTRACTING COMMAND

WARREN, MICHIGAN 48397-5000

KATHY KESSLER

EMAIL: KATHY.A.KESSLER.CIV@MAIL.MIL

W56HZV-15-R-0095

2016JUL07

X

X 2016AUG24 03:00pm

/SIGNED/

2 signed

SEE SECOND PAGE FOR DESCRIPTION

1 6

CONTINUATION SHEET

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION A - SUPPLEMENTAL INFORMATION

Buyer Name: KATHY KESSLER

Buyer Office Symbol/Telephone Number: CCTA-HDB-N/(586)282-3538

Type of Contract 1: Firm Fixed Price

Kind of Contract: Supply Contracts and Priced Orders

Weapon System: Radar & Sensor

FMS REQUIREMENT

*** End of Narrative A0000 ***

Amendment: 0001

Prepared by: KAK

Date Prepared: August 2016

1. The purpose of Amendment 0001 to solicitation W56HZV15R0095 is to extend the delivery date to 24 August 2016, change the wrecker type on CLIN 0002AA, and update the Specifications and technical information questionnaire.

2. The solicitation closing date is being extended from 7 August 2016 to 25 August 2016.

3. Changes to CLIN 0002AA: Description is being changed form a 10 Ton Flatbed Wrecker to a 10 Ton Wrecker with Rotator Boom.

4. Attachment 0001 Specification and Attachment 0002 Technical Information Questionnaire (TIQ) for 6 Ton Flatbed Wrecker with a date of

28 September 2015 is being updated to reflect a Ford F-750 chassis dated 2 August 2016.

5. Attachment 0003 Specification and Attachment 0004 Technical Information Questionnaire (TIQ) for 10 Ton Flatbed Wrecker dated 28

September 2015 is being updated to reflect a 10 Ton Wrecker with Rotator Boom dated 2 August 2016.

6. Exhibit D dated 2 August 2016 - Contractor Special Tools for 10 Ton Wrecker with Rotator Boom.

*** END OF NARRATIVE A0002 ***

2 6

W56HZV-15-R-0095 0001

PIIN/SIIN

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

SECTION B - SUPPLIES OR SERVICES AND PRICES/COSTS

0001 6 TON WRECKER FLATBED

NSN: 9999-99-999-9999

Mfr CAGE: 00000

Mfr Part Number: 2320000C0MVEH

0001AA 6 TON COMMERCIAL WRECKER 8 EA $ $ ________________________ ______________ __________________

COMMODITY NAME: 6 TON WRECKER FLATBED

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J547Y455EH PRON AMD: 02

FMS COUNTRY/CASE: JO/YAE

Ford F-750 6 Ton Flatbed 4x4 Wrecker in accordance with the Contract Specification (Attachment 0001)dated 2 August 2016 and the Technical Information

Questionnaire (Attachment 0002)dated 2 August 2016.

Exterior color shall be Tan.

Active Radio Frequency Identification (RFID) tags are required in accordance with the requirements set forth in the Specification (Attachment 0001).

The Contractor shall list the VIN/Serial number and corresponding RFID tag number for each item in the receiving report.

The FMS case designator (JO-B-YAE) must be listed on the shipping label.

An extra set of shipping documents should be placed in the glove box of the vehicle/item, or taped to the interior of the vehicle/item.

Another set of shipping documents shall be emailed to: Steven.w.king.civ@mail.mil

(End of narrative B001)

Packaging and Marking _____________________

PACKAGING/PACKING/SPECIFICATIONS:

STANDARD COMMERCIAL PACKAGING AND MARKING

LEVEL PRESERVATION: Commercial

LEVEL PACKING: Commercial

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

3 6

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

0002 10 TON WRECKER ROTATOR

NSN: 2320-00-0C0-MVEH

Mfr CAGE: 00000

Mfr Part Number: 2320000C0MVEH

0002AA COMMERCAIL 10 TON WRECKER WITH ROTATOR BOOM 4 EA $ $ ___________________________________________ ______________ __________________

COMMODITY NAME: 10 TON WRECKER ROTATOR

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J547Y297EH PRON AMD: 01

FMS COUNTRY/CASE: JO/YAE

Packaging and Marking _____________________

PACKAGING/PACKING/SPECIFICATIONS:

STANDARD COMMERCIAL PACKAGING AND MARKING

LEVEL PRESERVATION: Commercial

LEVEL PACKING: Commercial

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

4 6

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

5 6

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION J - LIST OF ATTACHMENTS

List of Number List of Number

Addenda Title Date of Pages Transmitted By Addenda Title Date of Pages Transmitted By________________ ____________________________________________________________ _______________ ____________ _______________________________ ____________________________________________________________ _______________ ____________ _______________

Exhibit D COMMERCIAL SPECIAL TOOLS FOR 10 TON WRECKER ROTATOR BOOM 02-AUG-2016 002 EMAIL

Attachment 0001 SPECIFICATION FOR 6 TON WRECKER FLATBED 02-AUG-2016 004 DATA

Attachment 0002 TECHNICAL INFORMATION QUESTIONNAIRE 6 TON WRECKER 02-AUG-2016 008 EMAIL

Attachment 0003 SPECIFICATION FOR 10 TON WRECKER WITH ROTATOR BOOM 02-AUG-2016 004 DATA

Attachment 0004 TECHNICAL INFORMATION QUESTIONNAIRE 02-AUG-2016 008 EMAIL

6 6

MOD/AMD

ATT/EXH ID

PAGE

Attachment 0001

ATTACHMENT 0001

AMENDEMENT 0001

SPECIFICATION

WRECKER, 6 TON FLATBED

DATE: 2 AUGUST 2016

THE VEHICLE SHALL BE PROVIDED WITH ALL NEW PARTS, THE MANUFACTURERS STANDARD EQUIPMENT, AND THE FOLLOWING MINIMUM EQUIPMENT AND

CAPABILITIES:

1. CONFIGURATION

1.1. The vehicle shall be a flatbed (rollback carrier) truck, 2016 model year or later.

1.2. The vehicle shall be based on a Ford F-750 chassis.

1.3. The vehicle shall be capable of loading and carrying at least 12,000 pounds (5,443 kg) of payload on the flatbed deck.

1.4. The vehicle shall be provided with less than 100 miles (160 km) on the odometer.

1.5. The vehicle shall meet US Federal Motor Vehicle Safety Standards (FMVSS).

2. EQUIPMENT

2.1. The vehicle shall be a flatbed (rollback carrier) truck with all standard equipment and the options specified herein.

2.2. The vehicle shall be provided with a lockable toolbox (es) or secured stowage compartment(s) that are environmentally sealed and mounted on the exterior of the vehicle, but not on flatbed area. All locks for the toolbox (es) and stowage compartment(s) shall be identically keyed for all vehicles. A minimum of two keys shall be provided with each toolbox or secured stowage compartment.

2.2.1. The tool box(es) and stowage compartments shall be provided with the following tools:

2.2.1.1. Standard tools required for simple operator level maintenance (a wrench and socket set, screwdrivers, adjustable wrench, pliers, and hammer).

2.2.1.2. Tire changing tools.

2.2.1.3. Lifting jack with a minimum capacity of 1/2 Gross Vehicle Weight (GVW).

2.2.1.4. Portable air compressor, tire inflating hose with quick-connect fittings on both ends (of sufficient length to inflate all tires on the vehicle), chuck (capable of filling inner rear tires as well as the other tires on the vehicle), and a pressure gauge.

2.2.1.5. Three red emergency reflective triangles and a first aid kit.

2.3. Two 5-gallon (or two 20 liter) jerry cans for diesel fuel shall be provided with mounting brackets. The jerry cans shall be labeled Diesel Fuel Only in English and Arabic. Location shall not be on the flatbed.

2.4. Rear wheels shall be covered by metal fenders or a combination of fenders and body structure with anti-sail mud flaps.

2.5. The vehicle shall be equipped with a brush guard.

2.6. The vehicle shall be provided with two front and two rear frame-mounted tow hooks or eyes.

2.7. An ABC type fire extinguisher, minimum 10\~pound (4.5\~kg) capacity, with mounting bracket shall be provided.

2.7.1. Fire extinguisher shall not be located on the flatbed.

2.8. Language requirements:

2.8.1. All instruction diagrams and warning labels shall be in both Arabic and English, or in universal symbols, and shall be permanently affixed to the vehicle.

2.8.2. Fuel filler cap or area close to the filler door shall be labeled with the type of fuel compatible with the vehicle in both Arabic and English, or in universal symbols.

2.8.3. A manual(s) shall be provided for every vehicle and written in both Arabic and English.

2.8.3.1. All manuals provided shall have an amendment stating the ability to operate on ultra-high sulfur diesel fuel content (10,000 ppm or 1%).

3. RATINGS, WEIGHTS, and DIMENSIONS

3.1. Vehicle ratings shall be the manufacturers published rating at the time of offer.

W56HZV-15-R-0095

ATT/EXH ID

PAGE

Attachment 0001

3.2. All individual components, including engine, transmission, driveline, frame, brakes, axles, suspension and tires shall be rated at or above the GVW.

3.3. Overall vehicle width (excluding mirrors) shall not be more than 98.5 inches (2.5 m).

4. CHASSIS

4.1. A 4x4 driveline shall be provided.

4.2. A lockable or limited slip differential shall be provided on the rear axle.

4.2.1. If a lockable differential is provided, it shall be capable of being engaged automatically or by the driver without leaving the drivers position.

5. ENGINE

5.1. Vehicle shall be provided with a turbocharged diesel engine capable of performing as specified herein on ultra-high sulfur content diesel fuel (10,000 ppm or 1%).

5.2. Engine shall be provided with the heaviest-duty available cooling and air filtration system designed for very hot, dusty environments (114\'b0F or 46\'b0C).

6. TRANSMISSION

6.1. The vehicle shall be provided with an automatic transmission.

7. STEERING

7.1. Left-hand drive and power steering shall be provided.

8. BRAKES

8.1. The vehicle shall be provided with service brakes which include an Anti-lock Brake System (ABS).

9. WHEEL ASSEMBLY (TIRE AND WHEEL)

9.1. Vehicle shall be provided with tubeless, on-off road radial tires.

9.2. All tires shall be of the same size, load rating and tread design, and all wheels shall be interchangeable, including spare wheel and tire assembly.

9.3. A full size spare tire and wheel assembly with holder shall be provided.

10. ELECTRICAL SYSTEM

10.1. The vehicle shall be provided with the chassis OEMs heaviest-duty alternator, and dual, heavy-duty, maintenance-free batteries.

10.2. The vehicle shall be provided with either one of the following:

10.2.1. Light bar permanently mounted to the top of the cab, or headboard, with at least two yellow rotating warning lights

(halogen, light emitting diode, or strobe-type).

10.2.2. Two yellow beacons permanently mounted to the top of the cab, or headboard, (halogen, light emitting diode, or strobe-type).

10.3. Rear-facing work lights to assist in nighttime loading and unloading operations shall be provided.

10.4. The vehicle shall be provided with back-up lights and an alarm.

11. PERFORMANCE

11.1. Vehicle shall be capable of being stored, started, and operated in temperatures ranging from 14 to 114 \'b0F (\_10 to

46\~\'b0C).

11.1.1. The vehicle shall be provided with a winterization kit for cold weather starting.

ATT/EXH ID

PAGE

Attachment 0001

11.2. Vehicle shall be capable of operating 40% of mission on sandy roads and trails, 50% on paved roads, and 10% off-road.

12. COLOR

12.1. The exterior color of the vehicle (including, the cab, deck surface, and side rails) shall be tan.

13. CAB

13.1. Cab shall accommodate driver and a minimum of one passenger.

13.2. Manufacturers heavy-duty air conditioning, heating, and defrosting systems shall be provided. Air conditioning shall be suitable for a hot, desert environment (114\'b0F or 46\'b0C temperature).

14. RECOVERY BODY, DECK, AND RECOVERY EQUIPMENT

14.1. Deck Requirements:

14.1.1. Deck shall be steel, have a diamond patterned surface, and be of appropriate thickness and strength.

14.1.2. Minimum deck length: 20 feet (6.1 meters).

14.1.3. Maximum deck width: 98.5 inches (2.5 meters).

14.1.4. Minimum deck capacity: 12,000 lbs (5,443 kg).

14.1.5. The deck shall be provided with removable side rails with stowage provisions on the vehicle.

14.1.6. A minimum of six (6) ratcheting tie-down straps compatible with the flatbed tie-down points. Tie-down straps shall be of appropriate length and rating for the payload.

14.1.7. The deck shall be provided with 12 tie-down points, 6 on each side of the flatbed, compatible with tie-down straps specified in 14.1.6, and all provisions required for securing a vehicle on the deck.

14.1.7.1. An integrated, lockable, and water-resistant storage compartment shall be available on the vehicle for the side rails and tie-down straps.

14.2. Vehicle shall be provided with a minimum 8,000 lb (3,629 kg) capacity (1st drum layer) hydraulic loading winch with a minimum of 50 feet (15.24 meters) of 3/8 inch (9.5 mm) cable with a safety factor of 50% above maximum line pull capacity, and equipped with overload protection.

14.2.1. A roller fairlead shall be provided with the winch.

14.2.2.Lighting at the winch area shall be provided for night time operations.

14.3. The front of the deck shall be equipped with a deck-mounted headboard.

14.4. Passenger-side controls (right side of the vehicle) for the recovery equipment shall be provided.

14.4.1. Recovery equipment controls shall be located in lockable, water resistant enclosures. Enclosures shall be identically keyed for all vehicles. A minimum of two keys shall be provided.

14.4.2. Night time operation of the controls shall be made possible with either a lighted enclosure or individually lighted controls.

14.5. All controls shall be marked in Arabic and English, or labeled in universal symbols.

15. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS

15.1 Each vehicle or item and associated lot of spares shall be tagged with a removable active RFID data rich tracking tag, specifically designated as either.

15.1.1 Savi ST-654-031

15.1.2 Savi ST-654-040

15.1.3 Evigia EV3-DRT

15.1.4 Identec I-Q310 DRT

15.2 The active RFID tag shall have at least 128 Kbytes of memory.

15.3 The active RFID tag shall be compliant with ISO 18000/7.

15.4 The tag shall be located on the exterior of the vehicle or item in a noticeable and easily observable spot. The tag for the spares shall be located in a noticeable and easily observable spot on the exterior of the pallet or container.

15.5 The tag shall be securely affixed to the vehicle or item in such a way that it cannot fall off. Securing the RFID tag with two or more plastic cable ties is the preferred method.

15.6 The tag data and electronic data field format shall be in accordance with specifications established by Joint Total Asset

ATT/EXH ID

PAGE

Attachment 0001

Visibility (JTAV) version 2.0, section 3.4.1 Commodity Item Database Format with the following clarifications:

15.6.1 The document field titled DOCUMENT shall be the document number (e.g. milstrip) as specified by the Government procuring agency.

15.6.2 The MISC1 field shall be the item serial number, if available.

15.6.3 The MISC2 field shall be used for user comments (e.g. contract number).

15.6.3.1 The JTAV - V2.0 data format specification is available at:

//www.ndia.org/Divisions/Divisions/Logistics/Documents/Content/ContentGroups/Divisions1/Logistics/4RF_Tag_Data_Specification_V2.pdf

ATT/EXH ID

PAGE

Attachment 0003

ATTACHMENT 0003

AMENDEMENT 0001

SPECIFICATION

10 TON WRECKER WITH ROTATOR BOOM

2 AUGUST 2016

THE VEHICLE SHALL BE PROVIDED WITH ALL NEW PARTS, THE MANUFACTURERS STANDARD EQUIPMENT, AND THE FOLLOWING MINIMUM EQUIPMENT AND

CAPABILITIES:

1. CONFIGURATION

1.1. The vehicle shall be a 10 ton wrecker rotator truck, 6x6, and 2016 model year or later.

1.2. The vehicle shall be provided with less than 100 miles (160 km) on the odometer.

2. SAFETY

2.1. The vehicle shall meet Federal Motor Vehicle Safety Standards (FMVSS) or one of the following: Gulf Cooperation Council (GCC), vehicle safety standards set forth by Economic Commission for Europe (ECE), European Economic Community (EEC), Australian Design

Rules (ADR), or the Japanese Industrial Standards (JIS).

3. EQUIPMENT

3.1. The vehicle shall be equipped with all equipment and the options specified herein.

3.2. The vehicle shall be provided with a lockable toolboxes or secured stowage compartment(s) that are environmentally sealed and mounted on the exterior of the vehicle. All locks for the tool boxes and stowage compartments shall be identically keyed for all vehicles. A minimum of two keys shall be provided with each toolbox or secured stowage compartment.

3.2.1. The tool boxes and stowage compartments shall be provided with the following tools and equipment:

3.2.1.1. Standard tools required for simple operator level maintenance (wrench and socket set, screwdrivers, adjustable wrench, pliers, and hammer).

3.2.1.2. Tire changing tools.

3.2.1.3. Lifting jack with a minimum capacity of at least 50% of the vehicle Gross Vehicle Weight (GVW).

3.2.1.4. Tire inflating hose with quick-connect fittings on both ends (of sufficient length to inflate all tires on the vehicle), chuck (capable of filling inner rear tires as well as the other tires on the vehicle), and a pressure gauge.

3.2.1.5. Three red emergency reflective triangles and a first aid kit.

3.2.1.6. The towing and lifting equipment listed in section 15 of this specification.

3.3. An easily accessible compressed air receptacle shall be provided on the body of the vehicle, powered by the vehicles compressed air system.

3.4. Two 5-gallon (or two 20 liter) jerry cans for diesel fuel shall be provided with mounting brackets. The jerry cans shall be labeled Diesel Fuel Only in English and Arabic. Location shall not interfere with the operation of the vehicle.

3.5. Rear wheels shall be provided with anti-sail mud flaps.

3.6. The vehicle shall be equipped with a brush guard.

3.7. The vehicle shall be provided with two front and two rear frame-mounted tow hooks or eyes.

3.8. An ABC type fire extinguisher, minimum 10\~pound (4.5\~kg) capacity, with mounting bracket shall be provided.

3.9. Language requirements:

3.9.1. All instruction diagrams and warning labels shall be in both Arabic and English, or in universal symbols, and shall be permanently affixed to the vehicle.

3.9.2. The fuel filler cap or area close to the filler door shall be labeled with the type of fuel compatible with the vehicle in both Arabic and English, or in universal symbols.

3.9.3. A manual(s) shall be provided for every vehicle and written in both Arabic and English.

3.9.3.1. All manuals provided shall have an amendment stating the ability to operate on ultra-high sulfur diesel fuel content (10,000 ppm or 1%).

4. RATINGS, WEIGHTS, and DIMENSIONS

ATT/EXH ID

PAGE

Attachment 0003

4.1. Vehicle ratings shall be the manufacturers published rating at the time of offer.

4.2. All individual components, including engine, transmission, driveline, frame, brakes, axles, suspension and tires shall be rated at or above the GVW.

4.3. Overall vehicle width (excluding mirrors) shall not be more than 98.5 inches (2.5 meters).

4.4. Vehicle shall be provided with a minimum of 12 inches (30.5 cm) ground clearance.

5. CHASSIS, DRIVELINE, AXLES, and SUSPENSION

5.1. A 6x6 driveline shall be provided.

5.2. Manufacturers heavy duty springs, shocks and axles shall be provided.

5.3. Each rear axle shall be provided with a rear limited-slip or lockable differential.

5.4. All axle traction control devices shall be engaged automatically, or by the driver without leaving the drivers position.

5.5. Rear axle(s) ratios shall be the same for all vehicles.

6. ENGINE

6.1. Vehicle shall be provided with a diesel engine, minimum 300 hp (224 kW), capable of performing as specified herein on ultra-high sulfur content diesel fuel (10,000 ppm or 1%).

6.2. Engine shall be provided with the heaviest-duty available cooling and air filtration system designed for very hot, dusty environments (114\'b0F or 46\'b0C).

6.3. Vehicle shall be able to operate from an integral fuel tank(s) for at least 250 miles (400km)on highway surfaces at an average speed of not less than 40 mph (64 kph).

7. TRANSMISSION

7.1. The vehicle shall be provided with an automatic transmission.

8. STEERING

8.1. Left-hand drive and power steering shall be provided.

9. BRAKES

9.1. The vehicle shall be provided with service brakes which include an Anti-lock Brake System (ABS) and an exhaust brake.

10. WHEEL ASSEMBLY (TIRE AND WHEEL)

10.1. Vehicle shall be provided with tubeless, on-off road radial tires.

10.2. All tires shall be of the same size, load rating and tread design, and all wheels shall be interchangeable, including spare wheel and tire assembly.

10.3. A spare tire and wheel assembly with holder shall be provided.

11. ELECTRICAL SYSTEM

11.1. The vehicle shall be provided with the chassis OEMs heavy-duty alternator, and a minimum of two, heavy-duty, maintenance-free batteries.

11.2. A 24/12 dual volt electrical system shall be provided.

11.3. The following circuits shall be operated at 12 volts:

11.3.1. A 20 amp circuit in cab for a radio.

11.3.2. All vehicle exterior lighting.

ATT/EXH ID

PAGE

Attachment 0003

11.4. The vehicle shall be provided with either one of the following:

11.4.1. Light bar permanently mounted to the top of the cab with at least two yellow rotating warning lights (halogen, light emitting diode, or strobe-type).

11.4.2. Two yellow beacons permanently mounted to the top of the cab (halogen, light emitting diode, or strobe-type).

11.5. Rear-facing work lights to assist in nighttime operations shall be provided.

11.6. The vehicle shall be provided with back-up lights and an alarm.

12. PERFORMANCE

12.1. Vehicle shall be capable of being stored, started, and operated in temperatures ranging from 14 to 114 \'b0F (\_10 to

46\~\'b0C).

12.1.1. The vehicle shall be provided with a winterization kit for cold weather starting.

12.2. Vehicle shall be capable of operating 40% of mission on sandy roads and trails, 50% on paved roads, and 10% off-road.

12.3. The vehicle at curb weight shall be able to maintain a speed of at least 55 mph (89kph) on a level highway.

13. VEHICLE RECOVERY PERFORMANCE

13.1. Vehicle shall be capable of lifting and towing wheeled vehicles without damage or permanent deformation to the recovery vehicle or towed vehicle, as specified below:

13.2. The vehicle shall be capable of lifting loads with the rotator boom and towing vehicles as follows:

13.2.1. Lifting 15,000 pounds (6,800 kilograms) at 9.84 feet (3 meters), from the edge of the wrecker when supported and 8,000 pounds (3,629 kilograms) at 9.84 feet (3 meters), from the edge of the wrecker when unsupported.

13.2.1.1. Towing wheeled vehicles of up to 40,000 pounds (18,144 kilograms).

13.2.2. With all tires of the towed vehicles on the ground.

14. COLOR

14.1. The exterior color of the vehicle (including the cab and wrecker body) shall be tan.

15. CAB

15.1. Cab shall accommodate driver and a minimum of one passenger.

15.2. Manufacturers heavy-duty air conditioning, heating, and defrosting systems shall be provided. Air conditioning shall be suitable for a hot, desert environment (114\'b0F or 46\'b0C temperature).

16. WRECKER BODY AND ROTATOR BOOM EQUIPMENT

16.1. Body Requirements:

16.1.1. Maximum body width: 98.5 inches (2.5 meters)

16.2. Vehicle shall NOT be equipped with a under lift.

16.3. Vehicle shall be provided with a rear mounted minimum 20 ton drag winch (18,144 kg) capacity (1st drum layer) hydraulic loading winch with a minimum of 200 feet (61 meters) of 3/4 inch (19.05 mm) cable with a safety factor of 50% above maximum line pull capacity, and equipped with overload protection and air operated free spool.

16.3.1. A roller fairlead shall be provided with the winch.

16.3.2. Lighting at the winch area shall be provided for night time operations.

16.4. Passenger-side controls (right side of the vehicle) for the recovery equipment shall be provided.

16.4.1. Recovery equipment controls shall be located in lockable, water resistant enclosures. Enclosures shall be identically keyed for all vehicles. A minimum of two keys shall be provided.

16.4.2. Night time operation of the controls shall be made possible with either a lighted enclosure or individually lighted controls.

16.5. All controls shall be marked in Arabic and English, or labeled in universal symbols.

ATT/EXH ID

PAGE

Attachment 0003

16.6. Boom shall rotate from the stowed position, a minimum 135 degrees clockwise and from the stowed position, a minimum 135 degrees counter-clockwise.

16.7. Hydraulic actuated outriggers shall be installed at the front and rear of wrecker body.

16.8. The vehicle shall be provided with a recovery boom with the following capabilities and features:

16.8.1. Lifting rating shall be at least 50,000 lbs. (22,680 kg) when retracted, and at least 15,000 lbs. (6,800 kg) when fully extended (as defined by SAE J2512).

16.9. The vehicle shall be provided with a recovery winch with the following capabilities and features:

16.9.1. Variable speed hydraulic winch shall be provided, rated at no less than 25,000 pounds (11,340 kg) and equipped with wire rope that is at least 5/8 inch by 200 feet (16 millimeters by 61 meters).

16.9.1.1. The winch shall be mounted in such a way to withstand full capacity pulls without damage or deformation to the vehicle or any components.

16.9.2. Clutch releases (free spool).

16.9.3. Cable tensioners.

16.9.4. Two (2) snatch blocks, suitable for offered cable.

16.9.5. Two (2) clevis hooks.

16.10. All winches and hydraulic cylinders shall be provided with an overload safety system that will prevent the manufacturers ratings from being exceeded.

16.11. The vehicle shall also be provided with the following equipment and shall have dedicated stowage space on the vehicle:

16.11.1. At least one of each of the following: sand jack, air jack, and airbag jack.

16.11.2. Hoses and fittings for above equipment to operate from the vehicles compressed air system.

16.11.3. Tow bar or tow strap with minimum four (4) grade 80, five foot length by 5/8 inch safety chains with matching fittings.

16.11.4. Two wheel chocks.

16.12. Rear mounted electrical and air brake connections with integral dust covers shall be provided for towing of vehicles. Hoses of sufficient length for towing operations shall be provided, and shall have dedicated stowage space on the vehicle.

16.13. The hydraulics shall be controlled by the vehicles Power Take-Off (PTO).

16.13.1. The hydraulic controls shall be located inside the cab and be operable by the driver without leaving the drivers seat.

16. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS

16.1. Each vehicle or item and associated lot of spares shall be tagged with a removable active RFID data rich tracking tag, specifically designated as either:

16.1.1. Savi ST-654-031

16.1.2. Savi ST-654-040

16.1.3. Evigia EV3-DRT

16.1.4. Identec I-Q310 DRT

16.2. The active RFID tag shall have at least 128 Kbytes of memory.

16.3. The active RFID tag shall be compliant with ISO 18000/7.

16.4. The tag shall be located on the exterior of the vehicle or item in a noticeable and easily observable spot.

The tag for the spares shall be located in a noticeable and easily observable spot on the exterior of the pallet or container.

16.5. The tag shall be securely affixed to the vehicle or item in such a way that it cannot fall off. Securing the

RFID tag with two or more plastic cable ties is the preferred method.

16.6. The tag data and electronic data field format shall be in accordance with specifications established by Joint

Total Asset Visibility (JTAV) version 2.0, section 3.4.1 Commodity Item Database Format with the following clarifications:

16.6.1. The document field titled DOCUMENT shall be the document number (e.g. milstrip) as specified by the

Government procuring agency.

16.6.2. The MISC1 field shall be the item serial number, if available.

16.6.3. The MISC2 field shall be used for user comments (e.g. contract number).

16.6.3.1. The JTAV - V2.0 data format specification is available at:

://www.ndia.org/Divisions/Divisions/Logistics/Documents/Content/ContentGroups/Divisions1/Logistics/4RF_Tag

ATT/EXH ID

PAGE

Attachment 0003

_Data_Specification_V2.pdf