Attachment_0004_TIQ_-_Wrecker_Rotator _10_Ton.doc

Solicitation W56HZV-15-R-0095 Attachment 0002

Technical Information Questionnaire (TIQ)

June, 2016

FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD

10 TON WRECKER WITH ROTATOR BOOM

The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS, BLANKS, AND REQUIRED SUPPPORTING DOCUMENTATION REFERENCES. IF ANY OF YOUR ANSWERS REQUIRE FURTHER EXPLANATION, YOU MUST ALSO INCLUDE THAT IN THE APPLICABLE COMMENT SECTION. Failure to provide a response may result in the rejection of your proposal.

Units: The data provided in the TIQ is to be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

All written information is to be in English.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Supporting documentation is required, see paragraphs 2(a)(1), 2(g)(1), 4(a)(1), 9(a)(1), 9(f)(1), 10(e)(3), 15(a).

(b) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The Offeror shall also explain in detail the reasons for the modifications and redesigns.

(c) US Federal Motor Vehicle Safety Standards (FMVSS) can be obtained at the following website: http://www.access.gpo.gov/nara/cfr/waisidx_04/49cfr571_04.html

INFORMATION NOTES

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and passenger (350 pounds)).

(c) Gross Vehicle Weight (GVW) shall include curb weight of the vehicle and weight of the crew (350 pounds).

(d) Gross Vehicle Weight Rating (GVWR) shall be the maximum allowable total weight of the vehicle including curb weight, and maximum payload.

10 TON WRECKER WITH ROTATOR BOOM

GENERAL INFORMATION

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title FORMTEXT

(c) Company Name FORMTEXT

(d) Telephone and Fax Numbers FORMTEXT

(e) E-mail address FORMTEXT

(f) Mailing Address FORMTEXT

(g) Company Website FORMTEXT

Comments FORMTEXT

1. CONFIGURATION

(a) Has the vehicle been provided with all new parts? FORMDROPDOWN

(b) Is the vehicle a 2014 model year or later? FORMDROPDOWN

(c) Is the vehicle a 10 ton wrecker rotator, 6x6 truck? FORMDROPDOWN

1) Chassis Manufacturer:

2) Chassis Model:

3) Wrecker Rotator Body Manufacturer:

4) Wrecker Rotator Body Model:

(d) Does the vehicle have less than 100 miles on the odometer? FORMDROPDOWN

(e) Does the vehicle meet the US Federal Motor Vehicle Safety Standards (FMVSS) applicable to your proposal? FORMDROPDOWN Comments

2. EQUIPMENT

Is the vehicle equipped with the following (yes or no and briefly expand in comment section, as needed):

(a) All of the equipment found on a wrecker rotator 10 ton truck of this make and model? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all standard equipment found on a wrecker rotator 10 ton truck of this make and model must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Lockable toolbox (es) or stowage compartment(s) for storage of items listed in question “c” below? FORMDROPDOWN Number of tool boxes Location of toolbox(es) or stowage compartment(s) Maximum width of toolbox(es) or stowage compartment(s)? inch

1) Are all toolbox(es) or stowage compartment(s) environmentally sealed? FORMDROPDOWN

2) Are all toolbox(es) or stowage compartment(s) identically keyed for all vehicles? FORMDROPDOWN

3) How many keys are provided with each vehicle?

(c) Are the following items provided?

1) FORMCHECKBOX

Standard tools for simple operator level maintenance:

(i) FORMCHECKBOX Wrench FORMCHECKBOX Socket set FORMCHECKBOX Screwdrivers FORMCHECKBOX Adjustable wrench FORMCHECKBOX Pliers FORMCHECKBOX Hammer FORMCHECKBOX Others

2) FORMCHECKBOX

Tire changing tools; Describe

3) FORMCHECKBOX

Lifting jack; capacity tons

4) FORMCHECKBOX

Tire inflating hose with quick-connect fittings on both ends;

(i) Is the hose of sufficient length to inflate all tires on vehicle? FORMDROPDOWN

5) FORMCHECKBOX

Chuck

(i) Is the chuck capable of filling the inner rear tires as well as the other tires on the vehicle?

6) FORMCHECKBOX

Pressure gauge

7) FORMCHECKBOX

Three red emergency reflective triangles and a first aid kit.

8) FORMCHECKBOX

The towing and lifting equipment listed in section 15 of the specification.

(d) Is an easily accessible compressed air receptacle provided on the body of the vehicle, powered by the vehicles compressed air system? FORMDROPDOWN , if yes location: FORMTEXT

(e) Two jerry cans with mounting brackets? FORMDROPDOWN Capacity Location(s)

1) Are the jerry cans labeled “Diesel Fuel Only” in English and Arabic? FORMDROPDOWN

(f) Are anti-sail mud flaps provided for the rear wheels? FORMDROPDOWN

(g) Is the vehicle equipped with a brush guard? FORMDROPDOWN , if yes describe: FORMTEXT

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(h) Is the vehicle provided with two front and two rear frame-mounted tow hooks or eyes? FORMDROPDOWN

(i) Is an ABC type fire extinguisher provided with mounting bracket? FORMDROPDOWN ; Capacity FORMTEXT lbs, Location

(j) Language requirements:

1) Are all instructions, diagrams, and warning labels bilingual in both Arabic and English or universal symbols? FORMDROPDOWN

(i) Are they permanently affixed to the vehicle? FORMDROPDOWN

2) Is the fuel filler cap (or an area close to the filler door) provided with labels stating type of fuel that is compatible with the vehicle in both Arabic and English or universal symbols? FORMDROPDOWN

3) Are manuals provided for each vehicle in both Arabic and English? FORMDROPDOWN

4) Do all manuals contain an amendment in both Arabic and English stating the ability to operate on ultra-high sulfur content diesel fuel (10,000 ppm or 1%)? FORMDROPDOWN

Comments

3. RATINGS, WEIGHTS, and DIMENSIONS

(a) Are the vehicle ratings the manufacturer’s published ratings at the time of offer? FORMDROPDOWN

(b) Are all individual components, including engine, transmission, driveline, frame, brakes, axles, suspension, and tires rated at or above the GVW? FORMDROPDOWN

(c) Gross Vehicle Weight Rating (GVWR): pounds

Comments

WEIGHTS (pounds)

(d) Curb weight

(e) Weight of operator and one passenger 350 lbs

(f) Payload

(g) GVW (total of (d), (e), and (f))

(h) Weight distribution of truck (pounds):

1) Curb weight, front axle

2) Curb weight, rear axles

3) Curb weight, total (must equal (d) above)

(i) GVW weight distribution of truck (pounds):

1) Loaded, front axle

2) Loaded, rear axles

3) Loaded, total (must equal (g) above) Comments

DIMENSIONS (inches)

(j) Wheelbase

(k) Track width (from center-to-center of tires) Front

(l) Ground clearance

(m) Overall dimensions (at curb weight): Length Comments

4. CHASSIS, DRIVELINE, AXLES, and SUSPENSION

(a) Chassis: Manufacturer Model

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Yield strength of frame rails: psi

(c) Dimensions of frame rails: inch high by inch flange by inch thick

(d) Resistance Bending Moment (RBM) of each frame rail: in-lb

(e) What is the vehicle driveline configuration? FORMCHECKBOX 6x6 FORMCHECKBOX 6x4 Other

(f) Is a locking or limited slip differential provided for each rear axle? FORMDROPDOWN

1) Are all traction control devices engaged automatically or by the driver without leaving the driver’s position? (please describe)

(g) Are rear axle ratios the same for all vehicles? FORMDROPDOWN

Comments

5. ENGINE

(a) Manufacturer

(b) Number of cylinders

(c) Net horsepower at engine governed speed

(d) Maximum net torque

(e) Can the vehicle operate on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)? FORMDROPDOWN

1) If so, please describe any degradation in performance from operation on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)

(g) Is the vehicle provided with an Exhaust Gas Recirculation (EGR) valve, Diesel Particulate Filter (DPF), Diesel oxidation Catalyst (DOC), Selective Catalytic Reduction Catalyst (SCR) or any other emission control device? FORMDROPDOWN , if yes list emission control device(s): FORMTEXT

1) Have any vehicle modifications or alterations been made to allow the vehicle to operate on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)? FORMDROPDOWN

2) If so, please list the vehicle modifications or alterations: FORMTEXT

(h) Are the cooling system and air filtration system for the engine designed for a very hot (114°F), dusty environment? FORMDROPDOWN

1) Provide description of cooling system:

2) Describe air filtration system:

(i) Can the vehicle operate from an integral fuel tank(s) with a range of at least 250 miles on highway surfaces at an average speed of not less than 40 mph? FORMDROPDOWN

Comments

6. TRANSMISSION

(a) Is an automatic transmission provided? FORMDROPDOWN

1) Manufacturer Model

2) Number of speeds: Forward Reverse Comments

7. STEERING

(a) Is the vehicle left-hand drive? FORMDROPDOWN

(b) Is the vehicle equipped with power steering? FORMDROPDOWN

Comments

8. BRAKES

(a) Service brakes: Type Front Rear

1) Are the service brakes provided with ABS? FORMDROPDOWN

(b) Is an exhaust brake provided? FORMDROPDOWN

1) Manufacturer Model Comments

9. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Tires: Manufacturer

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Are all tires tubeless, on-off road radials? FORMDROPDOWN

(c) Are all tires, including spare, the same size, load rating and tread design? FORMDROPDOWN

(d) Are all wheels, including the spare, interchangeable? FORMDROPDOWN

(e) Is a spare tire and wheel assembly with holder provided? FORMDROPDOWN

1) Storage location of spare on vehicle Comments

10. ELECTRICAL SYSTEM

(a) Is the vehicle provided with the chassis OEM’s heaviest-duty alternator? FORMDROPDOWN , Output amps

(b) Are dual, heavy-duty batteries provided? FORMDROPDOWN

1) Are the batteries maintenance-free? FORMDROPDOWN

2) CCA each

(c) Is a 24/12 dual volt electrical system provided? FORMDROPDOWN

(d) Are the following circuits operated at 12 volts:

1) A 20 amp circuit in cab for a radio? FORMDROPDOWN

2) All vehicle exterior lighting? FORMDROPDOWN

(e) Is the vehicle equipped with either a light bar or beacons? FORMDROPDOWN , if yes:

1) If a light bar is provided:

(i) Manufacturer:

(ii) Model:

(iii) Color(s):

(iv) Location:

(v) Is the light bar permanently mounted to the vehicle?

2) If beacons are provided:

(i) Manufacturer:

(ii) Model:

(iii) Color(s):

(iv) Locations:

(v) Are the beacons permanently mounted to the vehicle?

3) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(f) Are rear-facing work lights provided to assist in nighttime loading and unloading operations? FORMDROPDOWN

(g) Is the vehicle provided with back-up lights and an alarm? FORMDROPDOWN

Comments

11. PERFORMANCE

(a) What are the minimum and maximum temperatures the vehicle can be stored, started, and operated in? Minimum ˚F, Maximum ˚F

1) Is the vehicle provided with a winterization kit for cold weather starting? FORMDROPDOWN , Describe

(b) Is the vehicle capable of operating 40% of mission on sandy roads and trails, 50% on paved roads, and 10% off-road? FORMDROPDOWN

(c) Is the vehicle at curb weight able to maintain a speed of at least 55 mph on a level highway?

Comments

12. VEHICLE RECOVERY PERFORMANCE

(a) Is the vehicle capable of lifting and towing wheeled vehicles without damage or permanent deformation to the recovery vehicle or towed vehicle, as specified below:

(b) Lifting loads with the rotator boom and towing vehicles as follows:

1) Lifting 15,000 pounds at 9.84 feet, from the edge of the wrecker when supported and 8,000 pounds at 9.84 feet, from the edge of the wrecker when unsupported? FORMDROPDOWN

(i) Towing wheeled vehicles of up to 40,000 pounds? FORMDROPDOWN

(c) Towing with all tires of the towed vehicle on the ground? FORMDROPDOWN

Comments

13. COLOR

(a) Is the exterior color of the vehicle (including the cab and wrecker body) tan? FORMDROPDOWN

Comments

14. CAB

(a) Type

(b) Seating capacity

(c) Is the heating and defrosting system the manufacturer’s heavy-duty system? FORMDROPDOWN

(d) Is the air conditioning system the manufacturer’s heavy duty system, suited for a hot, desert environment (114°F temperature)? FORMDROPDOWN

Comments

15. WRECKER BODY AND ROTATOR BOOM EQUIPMENT

(a) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a schematic showing the wrecker body, and rotator boom equipment layout, design, and storage details must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Body Requirements:

1) What is the maximum body width? FORMTEXT

(c) Is the vehicle equipped with a under lift? FORMDROPDOWN

(d) Is the vehicle provided with a rear mounted minimum 20 ton drag winch capacity (1st drum layer) hydraulic loading winch? FORMDROPDOWN

1) Length of cable FORMTEXT feet

2) Thickness of cable FORMTEXT inch

3) Safety factor of cable above maximum line pull capacity FORMTEXT

4) Is the winch equipped with overload protection and air operated free spool? FORMDROPDOWN

5) Is a roller fairlead provided with the winch? FORMDROPDOWN

6) Is lighting at the winch area provided for night time operations? FORMDROPDOWN

(e) Are passenger-side controls (right side of the vehicle) for the recovery equipment provided? FORMDROPDOWN

1) Are recovery equipment controls located in lockable, water resistant enclosures? FORMDROPDOWN

2) Are enclosures identically keyed for all vehicles? FORMDROPDOWN

3) How many keys are provided? FORMTEXT

4) Are night time operations of the controls possible with either a lighted enclosure or individually lighted controls? FORMDROPDOWN

(f) Are all controls marked in Arabic and English, or labeled in universal symbols? FORMDROPDOWN

(g) Does the boom rotate from the stowed position, a minimum 135 degrees clockwise and from the stowed position, a minimum 135 degrees counter-clockwise? FORMDROPDOWN

(h) Are hydraulic actuated outriggers installed at the front and rear of wrecker body? FORMDROPDOWN , if yes describe: FORMTEXT

(i) Recovery Boom:

1) Is the lifting rating at least 50,000 lbs when retracted, and at least 15,000 lbs when fully extended (as defined by SAE J2512)? FORMDROPDOWN

(j) Recovery Winch:

1) Is a variable speed hydraulic winch provided? FORMDROPDOWN

2) What is the rating of the winch? FORMTEXT pounds

3) Is the winch equipped with wire rope? FORMDROPDOWN , if yes:

(i) Diameter FORMTEXT inch

(ii) Length FORMTEXT feet

4) Is the winch mounted in such a way to withstand full capacity pulls without damage or deformation to the vehicle or any components? FORMDROPDOWN

5) Are the following items provided for the winch:

(i) Clutch releases (free spool)? FORMDROPDOWN

(ii) Cable tensioners? FORMDROPDOWN

(iii) Two (2) snatch blocks, suitable for offered cable? FORMDROPDOWN

(iv) Two (2) clevis hooks? FORMDROPDOWN

(k) Are all winches and hydraulic cylinders provided with an overload safety system that will prevent the manufacturer’s ratings from being exceeded? FORMDROPDOWN

(l) Is the vehicle provided with the following equipment:

1) Air powered tool set including impact driver and sockets for wheel lug nuts? FORMDROPDOWN

2) At least one of each of the following: sand jack, air jack, or airbag jack? FORMDROPDOWN

3) Hoses and fittings for above equipment to operate from the vehicle’s compressed air system? FORMDROPDOWN

4) Tow bar or tow strap with minimum four (4) grade 80, five foot length by 5/8 inch safety chains with matching fittings? FORMDROPDOWN

5) Two wheel chocks? FORMDROPDOWN

6) Dedicated stowage space on the vehicle for the items listed above? FORMDROPDOWN

(m) Are rear mounted electrical and air brake connections with integral dust covers provided for towing of vehicles? FORMDROPDOWN

1) Are hoses of sufficient length provided for towing operations? FORMDROPDOWN

2) Is there dedicated stowage space on the vehicle for these items? FORMDROPDOWN

(n) Are the hydraulics controlled by the vehicle’s Power Take-Off (PTO)? FORMDROPDOWN

1) Are the hydraulic controls located inside the cab and be operable by the driver without leaving the driver’s seat? FORMDROPDOWN

Comments

16. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS

(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID data rich tracking tag? FORMDROPDOWN ; if yes: Manufacturer FORMTEXT

; Model FORMTEXT

(b) How much memory does the provided active RFID tag have? FORMTEXT

(c) What standard is the active RFID tag built to? FORMTEXT

(d) Where is the RFID tag located on the vehicle or item and associated lot of spares? FORMTEXT

(e) How is the tag affixed to the vehicle or item and associated lot of spares? FORMTEXT

(f) Will the tag’s electronic format be in compliance with the JTAV version 2.0 specifications, section 3.4.1 format? FORMDROPDOWN

1) Will the Document field be programmed with the document number (e.g. “milstrip”) provided by the government agency? FORMDROPDOWN

2) Will the MISC1 field be programmed with the item serial number, if available? FORMDROPDOWN

3) Will the MISC2 field be programmed or reserved for comments (e.g. contract number)? FORMDROPDOWN

4) Which company or agency will “write to” or “program” the tag? FORMTEXT

Comments FORMTEXT

SOURCE SELECTION SENSITIVE, SEE FAR 3.104