TIQ_-_Wrecker_6_Ton_Flatbed_.doc

Solicitation W56HZV-15-R-0095 Attachment 0002 Amendment 0002 Technical Information Questionnaire (TIQ)

August, 2016

FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD

WRECKER, 6 TON FLATBED

The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS, BLANKS, AND REQUIRED SUPPPORTING DOCUMENTATION REFERENCES. IF ANY OF YOUR ANSWERS REQUIRE FURTHER EXPLANATION, YOU MUST ALSO INCLUDE THAT IN THE APPLICABLE COMMENT SECTION. Failure to provide a response may result in the rejection of your proposal.

Units: The data provided in the TIQ is to be provided in English units, unless otherwise specified. Metric units may be provided if clearly defined and identified.

All written information is to be in English.

In addition to responding to the questions below, the offeror shall provide the following:

(a) Supporting documentation is required, see paragraphs 3(a)(1), 3(f)(1), 5(a)(1), 10(a)(1), 11(c)(3), 15(a), and 15(c)(10).

(b) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the requirements of the specifications. The Offeror shall also explain in detail the reasons for the modifications or redesigns.

(c) US Federal Motor Vehicle Safety Standards (FMVSS) can be obtained at the following website: http://www.access.gpo.gov/nara/cfr/waisidx_04/49cfr571_04.html

INFORMATION NOTES

(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number shall be shown.

(b) Curb weight shall be weight of vehicle offered, completely equipped with coolant, fuel and lubricants, less the weight of the crew (driver and passenger (350 pounds)).

(c) Gross Vehicle Weight (GVW) shall include curb weight of the vehicle, weight of the crew (350 pounds), at least 12,000 pounds of full payload (assumed evenly distributed over the flatbed).

(d) Gross Vehicle Weight Rating (GVWR) shall be the maximum allowable total weight of the vehicle including curb weight, and maximum payload.

WRECKER, 6 TON FLATBED

GENERAL INFORMATION

Personnel Responding to Questionnaire:

(a) Name

(b) Job Title FORMTEXT

(c) Company Name FORMTEXT

(d) Telephone and Fax Numbers FORMTEXT

(e) E-mail address FORMTEXT

(f) Mailing Address FORMTEXT

(g) Company Website FORMTEXT

Comments FORMTEXT

1. CONFIGURATION

(a) Is the vehicle been provided with all new parts? FORMDROPDOWN

(b) Is the vehicle a 2016 model year or later? FORMDROPDOWN

(c) Is the vehicle provided a flatbed (rollback carrier) truck? FORMDROPDOWN

1) Manufacturer:

2) Model:

(d) Is the vehicle capable of carrying at least 12,000 pounds of payload on the flatbed deck? FORMDROPDOWN

(e) Does the vehicle have less than 100 miles (160 km) on the odometer? FORMDROPDOWN

2. SAFETY

(d) Does this vehicle meet all applicable US Federal Motor Vehicle Safety Standards (FMVSS)? FORMDROPDOWN

(e) If the vehicle does not meet FMVSS standards, which vehicle safety standards does the vehicle comply with? FORMDROPDOWN

Comments

3. EQUIPMENT

Is the vehicle equipped with the following (yes or no and briefly expand in comment section, as needed):

(a) All of the equipment found on a flatbed (rollback carrier) truck of this make and model? FORMDROPDOWN

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s) listing all standard equipment found on a flatbed (rollback carrier) truck of this make and model must be provided. State where this is provided in your proposal (e.g. page number and paragraph)

(b) Lockable toolbox (es) or stowage compartment(s) for storage of items listed in question “c” below? FORMDROPDOWN Number of tool boxes Location of toolbox(es) or stowage compartment(s) Maximum width of toolbox(es) or stowage compartment(s)? inch

1) Are all toolbox(es) or stowage compartment(s) environmentally sealed? FORMDROPDOWN

2) Are all toolbox(es) or stowage compartment(s) identically keyed for all vehicles? FORMDROPDOWN

3) How many keys are provided with each vehicle?

(c) Are the following items provided?

1) FORMCHECKBOX

Standard tools for simple operator level maintenance:

(i) FORMCHECKBOX Wrench FORMCHECKBOX Socket set FORMCHECKBOX Screwdrivers FORMCHECKBOX Adjustable wrench FORMCHECKBOX Pliers FORMCHECKBOX Hammer FORMCHECKBOX Others

2) FORMCHECKBOX

Tire changing tools; Describe

3) FORMCHECKBOX

Lifting jack; capacity tons

4) FORMCHECKBOX

Portable air compressor

5) FORMCHECKBOX

Tire inflating hose with quick-connect fittings on both ends;

(i) Is the hose of sufficient length to inflate all tires on vehicle? FORMDROPDOWN

6) FORMCHECKBOX

Chuck

(i) Is the chuck capable of filling the inner rear tires as well as the other tires on the vehicle?

7) FORMCHECKBOX

Pressure gauge

8) FORMCHECKBOX

Three red emergency reflective triangles and a first aid kit.

(d) Two jerry cans with mounting brackets? FORMDROPDOWN Capacity Location(s)

1) Are the jerry cans labeled “Diesel Fuel Only” in English and Arabic? FORMDROPDOWN

2) Are they located off the flatbed? FORMDROPDOWN Location(s)

(e) Are metal fenders or a combination of fenders and body structure provided with anti-sail mud flaps for the rear wheels? FORMDROPDOWN

(f) Is the vehicle equipped with a brush guard? FORMDROPDOWN , if yes describe: FORMTEXT

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(g) Is the vehicle provided with two front and two rear frame-mounted tow hooks or eyes? FORMDROPDOWN

(h) Is an ABC type fire extinguisher provided with mounting bracket? FORMDROPDOWN ; Capacity FORMTEXT lbs, Location

(i) Language requirements:

1) Are all instructions, diagrams, and warning labels bilingual in both Arabic and English or universal symbols? FORMDROPDOWN

(i) Are they permanently affixed to the vehicle? FORMDROPDOWN

2) Are fuel filler caps (or an area close to the filler door) provided with labels stating type of fuel that is compatible with the vehicle in both Arabic and English or universal symbols? FORMDROPDOWN

3) Are manuals provided for each vehicle in both Arabic and English? FORMDROPDOWN

4) Do all manuals contain an amendment in both Arabic and English stating the ability to operate on ultra-high sulfur content diesel fuel (10,000 ppm or 1%)? FORMDROPDOWN

Comments

4. RATINGS, WEIGHTS and DIMENSIONS

(a) Are the vehicle ratings the manufacturer’s published ratings at the time of offer? FORMDROPDOWN

(b) Do all individual component ratings meet or exceed the requirements? FORMDROPDOWN

(c) Gross Vehicle Weight Rating (GVWR): pounds

Comments

WEIGHTS (pounds)

(d) Curb weight

(e) Weight of operator and one passenger 350 lbs

(f) Payload (including fully loaded flatbed)

(g) GVW (total of (d), (e), and (f))

(h) Weight distribution of flatbed truck (pounds):

1) Curb weight, front axle

2) Curb weight, rear axle

3) Curb weight, total (must equal (d) above)

(i) GVW weight distribution of flatbed truck (pounds):

1) Loaded, front axle

2) Loaded, rear axle

3) Loaded, total (must equal (g) above) Comments

DIMENSIONS (inches)

(j) Wheelbase

(k) Track width (from center-to-center of tires) Front

(l) Ground clearance

(m) Distance from ground to flatbed

(n) Overall dimensions (at curb weight): Length Comments

5. CHASSIS

(a) Chassis manufacturer Model

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(b) Yield strength of frame rails: psi

(c) Dimensions of frame rails: inch high by inch flange by inch thick

(d) Resistance Bending Moment (RBM) of each frame rail: in-lb

(e) What is the vehicle driveline configuration? FORMCHECKBOX 4x2 FORMCHECKBOX 4x4 Other

(f) Rear axle configuration FORMDROPDOWN

(g) Is a rear locking or limited slip differential provided on the rear axle? FORMDROPDOWN

1) If a locking differential is provided, does it engage automatically or by the driver without leaving the driver’s position? FORMDROPDOWN

Comments

6. ENGINE

(a) Manufacturer

(b) Number of cylinders

(c) Is the vehicle engine turbocharged? FORMDROPDOWN

(d) Net horsepower at engine governed speed

(e) Maximum net torque

(f) Can the vehicle be operated on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)? FORMDROPDOWN

1) If so, please describe any degradation in performance from operation on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)

(g) Is the vehicle provided with an Exhaust Gas Recirculation (EGR) valve, Diesel Particulate Filter (DPF), Diesel oxidation Catalyst (DOC), Selective Catalytic Reduction Catalyst (SCR) or any other emission control device? FORMDROPDOWN , if yes list emission control device(s): FORMTEXT

(h) Have any vehicle modifications or alterations been made to allow the vehicle to operate on ultra-high sulfur content diesel fuel (10,000 PPM or 1%)? FORMDROPDOWN

1) If so, please list the vehicle modifications or alterations: FORMTEXT

(i) Are the cooling system and air filtration system for the engine designed for a very hot (114°F), dusty environment? FORMDROPDOWN

1) Provide description of cooling system:

2) Describe air filtration system:

Comments

7. TRANSMISSION

(a) Is an automatic transmission provided? FORMDROPDOWN

1) Manufacturer Model

2) Number of speeds: Forward Reverse Comments

8. STEERING

(a) Is the vehicle left-hand drive? FORMDROPDOWN

(b) Is the vehicle equipped with power steering? FORMDROPDOWN

Comments

9. BRAKES

(a) Service brakes: Type Front Rear

1) Are the service brakes provided with ABS? FORMDROPDOWN

Comments

10. WHEEL ASSEMBLY (TIRE AND WHEEL)

(a) Tires: Manufacturer:

1) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(b) Are all tires tubeless, on-off road radials? FORMDROPDOWN

(c) Are all tires, including spare, the same size, load rating and tread design? FORMDROPDOWN

(d) Are all wheels, including the spare, interchangeable? FORMDROPDOWN

(e) Is a full size spare tire and wheel assembly with holder provided? FORMDROPDOWN

1) Storage location of spare on vehicle Comments

11. ELECTRICAL SYSTEM

(a) Is the vehicle provided with the chassis OEM’s heaviest-duty alternator? FORMDROPDOWN , Output amps

(b) Are dual, heavy-duty batteries provided? FORMDROPDOWN

1) Are the batteries maintenance-free? FORMDROPDOWN

2) CCA each

(c) Is the vehicle equipped with either a light bar or beacons? FORMDROPDOWN , if yes:

1) If a light bar is provided:

(i) Manufacturer:

(ii) Model:

(iii) Color(s):

(iv) Location:

(v) Is the light bar permanently mounted to vehicle? FORMDROPDOWN

2) If beacons are provided:

(i) Manufacturer:

(ii) Model:

(iii) Color(s):

(iv) Locations:

(v) Are the beacons permanently mounted to vehicle? FORMDROPDOWN

3) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(d) Are rear-facing work lights provided to assist in nighttime loading and unloading operations? FORMDROPDOWN

(e) Is the vehicle provided with back-up lights and an alarm? FORMDROPDOWN

Comments

12. PERFORMANCE

(a) What are the minimum and maximum ambient temperatures the vehicle can be stored, started, and operated in? Minimum ˚F, Maximum ˚F

1) Is the vehicle provided with a winterization kit for cold weather starting? FORMDROPDOWN , if yes describe: FORMTEXT

(b) Is the vehicle capable of operating 40% of mission on sandy roads and trails, 50% on paved roads, and 10% off-road? FORMDROPDOWN

Comments

13. COLOR

(a) Is the color of the vehicle (including the cab, the deck surface, and side rails) tan? FORMDROPDOWN

Comments

14. CAB

(a) Type

(b) Seating capacity

(c) Is the heating and defrosting system the manufacturer’s heavy-duty system? FORMDROPDOWN

(d) Is the air conditioning system the manufacturer’s heavy duty system, suited for a hot, desert environment (114°F temperature)? FORMDROPDOWN

Comments

15. RECOVERY BODY, DECK AND RECOVERY EQUIPMENT

(a) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a schematic showing the recovery body, deck, and equipment layout, design, storage details must be provided. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(b) Deck:

1) Deck material ; Textured surface? FORMDROPDOWN if yes, describe

2) Thickness of deck: inch

(i) Are cross members used underneath the deck? FORMDROPDOWN , if yes, size: inches, spacing between cross members: inches

3) Length of deck: feet

4) Width of deck: inches

5) Deck capacity: pounds

6) Does the deck have side rails? FORMDROPDOWN , if yes, height: inches

(i) Are the side rails removable? FORMDROPDOWN , if yes, are there stowage provisions on the vehicle? FORMDROPDOWN if yes, describe

7) Are ratcheting tie-downs straps provided which are compatible with the flatbed tie-down points? FORMDROPDOWN if yes:

(i) Number provided , rating tons

8) Number of tie-down points on flatbed , Locations , Type(s) (e.g. key slots, D rings) , capacity pounds

9) Is the vehicle supplied with all provisions required for securing a vehicle onto the deck? FORMDROPDOWN , if yes:

(i) List equipment provided:

(ii) Is all the above listed equipment provided with an integrated, lockable and water-resistant storage compartment on the vehicle? FORMDROPDOWN

(c) Hydraulic loading winch:

1) Rated capacity (1st drum layer): pounds

2) Location:

3) Cable length: feet

4) Cable diameter: inches

5) Cable safety factor: %

6) Overload protection provided? FORMDROPDOWN

7) Is a roller fairlead provided for the winch? FORMDROPDOWN

8) Is the remote control provided with its own storage space? FORMDROPDOWN , if yes describe:

9) Is lighting at the winch area provided for night-time operations? FORMDROPDOWN

10) SUPPORTING DOCUMENTATION REQUIRED: A brochure or specification sheet(s), and a picture must be provided for the winch and accessories. State where this is provided in your proposal (e.g. page number and paragraph) FORMTEXT

(d) Full height deck-mounted headboard provided? FORMDROPDOWN , if yes, describe:

(e) Are passenger-side controls (right side of vehicle) for the recovery equipment provided? FORMDROPDOWN Locations:

1) Are the controls located in lockable and water resistant enclosures? FORMDROPDOWN , if yes describe:

(i) Are all enclosures keyed alike? FORMDROPDOWN , Number of keys provided

2) Are the enclosures lighted, or are the controls individually lighted for night-time operations? FORMDROPDOWN , if yes, describe:

(f) Are all controls marked in Arabic and English, or labeled in universal symbols? FORMDROPDOWN

Comments

16. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS

(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID data rich tracking tag? FORMDROPDOWN ; if yes: Manufacturer FORMTEXT

; Model FORMTEXT

(b) How much memory does the provided active RFID tag have? FORMTEXT

(c) What standard is the active RFID tag built to? FORMTEXT

(d) Where is the RFID tag located on the vehicle or item and associated lot of spares? FORMTEXT

(e) How is the tag affixed to the vehicle or item and associated lot of spares? FORMTEXT

(f) Will the tag’s electronic format be in compliance with the JTAV version 2.0 specifications, section 3.4.1 format? FORMDROPDOWN

1) Will the Document field be programmed with the document number (e.g. “milstrip”) provided by the government agency? FORMDROPDOWN

2) Will the MISC1 field be programmed with the item serial number, if available? FORMDROPDOWN

3) Will the MISC2 field be programmed or reserved for comments (e.g. contract number)? FORMDROPDOWN

4) Which company or agency will “write to” or “program” the tag? FORMTEXT

Comments FORMTEXT

SOURCE SELECTION SENSITIVE, SEE FAR 3.104