Attachment 06.pdf

Request for Quote (RFQ) # W50S8G27Q0001

Replaced Obsolete Solicitation # W50S8G26QOR07

Issued on: October 19, 2026

150th MXG HC-130 Aircraft Wash

(The Quote must be valid for 90 days from the due date)

1. This document serves as the Request For Quote (RFQ) for commercial services prepared in accordance with Revolutionary

FAR Overhaul (RFO) Federal Acquisition Regulation (FAR) 12.202(b)(1). This is the only solicitation that will be issued; we are requesting quotes, and no written solicitation will follow. Please refer to "W50S8G27Q0001” on all quotes that are submitted to the Government for this combined synopsis/solicitation. This solicitation is issued as a Request for Quotation

(RFQ) and incorporates all provisions and clauses in effect through the Federal RFO FAR. All responsible sources are invited to submit a quote.

a. IMPORTANT Notices for Offerors

i. Governing Regulations: This solicitation is governed by the regulations effective February 1, 2026, under

Class Deviation 2026-O0028 – Revolutionary FAR Overhaul (RFO) Part 12, and DFARS 212.

ii. Business Classification: This acquisition is designated as a total small business set-aside. The North

American Industry Classification System (NAICS) code is 488190 Other Support Activities for Air

Transportation, and the Product Service Code (PSC) is PSC J015 maintenance/repair/rebuild of equipment-aircraft and airframe structural components. The standard size for this NAICS is $40,000,000.

iii. System for Award Management (SAM) Registration: To be considered for an award, all offerors must have an active registration in the System for Award Management (SAM) at https://sam.gov/.

iv. The contracting officer will verify the prospective awardee's representations and certifications in SAM prior to issuing an award. Failure to maintain SAM registration will result in the offeror being deemed non-responsive and potentially ineligible for the award.

v. Payment Instructions: For details regarding payment and acceptance, please refer to DFARS 252.232-7006

WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023), which is incorporated in full below. Please note that all payments will be 30 days after an invoice is submitted via Wide Area Work

Flow (WAWF) and accepted by the Government. Invoices can only be submitted after a completion/acceptance of an aircraft wash.

vi. Applicable Commercial Clauses: The following commercial provisions and clauses are applicable to this acquisition:

1. FAR 52.212-1: Instructions to Offerors—Commercial Products and Commercial Services (FEB

2026)

2. FAR 52.212-4: Terms and Conditions—Commercial Products and Commercial Services (FEB

2026)

vii. Additional Terms: No other terms and conditions have been deemed necessary for this acquisition beyond what is listed in this RFQ.

viii. 52.232-18 Availability of Funds (April 1984)

Funds are not presently available for this contract. The Government’s obligation under this contract is contingent upon the availability of appropriated funds from which payment for contract purposes can be made. No legal liability on the part of the Government for any payment may arise until funds are made available to the Contracting Officer for this contract and until the Contractor receives notice of such availability, to be confirmed in writing by the Contracting Officer.

b. QUESTIONS AND INQUIRIES: Please submit all questions and inquiries via email to SMSgt Edwin Widgeon at

150SOW.MSC.RFPRFQ@us.af.mil no later than October 15, 2026, at 11:00 AM MDT. Questions received after this time may not be acknowledged or answered.

c. QUOTE SUBMISSION: Please submit your quote via email to the points of contact listed above no later than

October 22, 2026 at 11:00 AM MDT. It is the vendor's responsibility to monitor SAM.gov for any questions and https://sam.gov/ mailto:150SOW.MSC.RFPRFQ@us.af.mil

Issued on: October 19, 2026 answers documents posted as well as amendments posted for this requirement. Quotes are to be submitted to

150SOW.MSC.RFPRFQ@us.af.mil.

d. LATE QUOTES: In accordance with FAR 52.212-1, any quotes received after the due date may be disqualified.

e. It is the offeror's responsibility to ensure the Government receives their quote before the deadline.

f. QUOTE CONFORMITY AND COMPLETENESS: Offerors are responsible for submitting a complete and conforming quote that addresses all submission requirements outlined in this solicitation.

i. Conformity with Instructions: Quotes that do not conform to the instructions, such as exceeding page limitations or failing to provide the requested information, may be considered unacceptable and may not be evaluated.

ii. Relevance of Information: To ensure an efficient evaluation, offerors should only submit the specific documents and information requested. Extraneous materials or ANY documents not explicitly required may not be evaluated.

g. EVALUATION. IAW RFO FAR 12.203(a); the following factors will be used to evaluate quotes:

i. FACTOR 1: TECHNICAL SOLUTION. Offerors shall submit a concise Technical Approach within their quotation that explains how they will execute the PWS requirements. (Page limitation 5 pages)

ii. FACTOR 2: EXPERIENCE. This factor evaluates the depth and relevance of the offeror's actual history in performing work similar in scope, complexity, and magnitude to this solicitation, as distinct from Past

Performance, which assesses the quality of that work. Offerors must demonstrate a history of execution on similar projects, as the Government will comparatively evaluate the depth and breadth of each offeror's experience to determine which offers represent the best value. (Attachment 3. Page Limitation 2 pages per experience). Attachment 3 must be used to submit experience, up to three experiences can be submitted. If a subcontractor is submitted to demonstrate experience, your company must utilize that same subcontractor upon contract award. Replacing them with a different subcontractor will constitute a breach of contract.

iii. FACTOR 3: PRICE. The Government will evaluate the offeror's total quoted price to ensure it is fair and reasonable. Total Evaluated Price (TEP) will be calculated based on the total price for all 10 washes (7 scheduled + 3 unscheduled) per year for the base year and four (4) option years and will encompass all applicable costs, including labor, materials, equipment, administrative fees, and travel. In accordance with

(IAW) FAR 52.217-5, Evaluation of Options, the Government will evaluate the base year and all four (4) option years to calculate the TEP. (Attachment 4).

1. In accordance with FAR 52.222-43, Fair Labor Standards Act and Service Contract Labor

Standards—Price Adjustment (Multiple Year and Option Contracts), contract unit prices will be adjusted upon the exercise of each option period to reflect the contractor’s actual increase in applicable wages and fringe benefits resulting from the incorporation of a new or revised

Department of Labor Wage Determination. Pursuant to FAR 52.222-43, offerors warrant that their quoted prices do not contain any allowance or contingency to cover increased costs for which adjustment is provided under the clause. Consequently, offerors shall not include contingencies or projected escalation for Service Contract Labor Standards (SCLS/SCA) wages and fringe benefits in option periods, and quoting identical pricing across the base year and option years for SCA-covered labor shall not be evaluated as unrealistic. Offerors may, at their discretion, include escalation across option years solely for non-labor operational expenses (e.g., commercial materials, supplies, equipment, administrative costs, and travel).

h. BASIS OF AWARD. IAW RFO FAR 12.203(c)(2) The contracting officer has broad discretion in establishing how quotations will be evaluated. The Government will award a single, firm-fixed-price purchase order to the vendor responsible whose quotation represents the best value to the Government. The Contracting Officer will determine offeror responsibility IAW RFO FAR 9.104. The Government may also utilize the Contractor Performance

Assessment Reporting System (CPARS) and the Federal Awardee Performance Integrity Information System mailto:150SOW.MSC.RFPRFQ@us.af.mil

Issued on: October 19, 2026

(FAPIIS), along with other Government and non-Government sources when determining the responsibility of an offeror. The Contracting Officer will conduct a comparative evaluation of all timely quotations.

i. Please note that the evaluation procedures of RFO FAR Part 14 (Sealed Bidding) and RFO FAR Part 15

(Contracting by Negotiation) do not apply to this acquisition. The Government is not required to, and will not establish or utilize formal evaluation plans, assign numerical, adjectival, or color-coded scores to quotations, or establish a competitive range.

ii. The Government will conduct a comparative evaluation of quotations to determine which quote represents the best value to the Government. Under RFO FAR Part 12 comparative evaluation procedures, the

Government will directly compare the relative factor of each vendor's Technical Approach and Experience against their quoted Price. Accordingly, the Government may select a higher-priced quotation for award if it is determined that the technical and experience advantages of that quote outweigh the price difference and represent the most advantageous offer. Conversely, the Government will not pay a premium price for technical or experience advantages that do not provide a clear benefit to the Government. The Contracting

Officer reserves the right to communicate with any, all, or none of the vendors at any point during the evaluation. These communications are not governed by the restrictive “discussions” rules of RFO FAR Part

15. The Government may solicit revised quotations or resolve minor details with one or more vendors without the obligation to open discussions or request final quote revisions from any vendors. Vendors are strongly encouraged to submit their best technical and pricing terms in their initial quotation.

i. CONTRACT TYPE. Firm Fixed Price (FFP) Contract

j. The established budget parameter for the entire 5-year Period of Performance (PoP) of this acquisition is estimated to be between $250,000.00 and $300,000.00.

i. This figure represents a budget guideline only; the offeror is not prohibited from quoting a price outside this range. The offeror may submit a quotation above or below this parameter if deemed necessary to accurately reflect their offered technical approach. The Government reserves the right to award a purchase order outside this budget parameters if it represents the best value.

2. GENERAL REQUIREMENT:

a. Seven (7) scheduled washes per year

b. Three (3) unscheduled washes per year

c. Period of Performance: One (1) Base Year and Four (4) Options Year. Total Five (5) Years.

d. Place of Performance: Hangar 1000 or 1002, Kirtland Air Force Base, NM 87117.

e. List of Attachments:

i. Attachment 01 – Performance Work Statement. Dated October 19, 2026

ii. Attachment 02 – SCA Wage Determination. Dated August 27, 2026

iii. Attachment 03 – Experience QA2

iv. Attachment 04 – Schedule QA2

v. Attachment 05 – Questions and Answers Document 1

vi. Attachment 05a – Questions and Answers Document 2

vii. Attachment 06 – PDF Copy of This Combined Synopsis_Solicitation for ease of reading

viii. Attachment 07 – 150 MXG Form 164

3. REQUIRED DOCUMENT. Failure to provide all required documentation listed below may result in the quotation being excluded from the comparative evaluation and eliminated from award consideration. Quotations exceeding the page limitations may also be excluded from the comparative evaluation and eliminated from award consideration.

i. TECHNICAL SOLUTION. 5 pages limitation

ii. ATTACHMENT 3 - EXPRIENCE. 2 pages limitation per experience (up to three experiences can be submitted)

iii. ATTACHMENT 4 – SCHEDULE

4. PROVISIONS/ CLAUSES INCORPORATED BY REFERENCE (IBR)

Issued on: October 19, 2026

Offerors are responsible for adhering to all applicable Federal Acquisition Regulation (FAR) and Defense Federal

Acquisition Regulation Supplement (DFARS) provisions and clauses for this solicitation. The full text of these regulations is available at https://www.acquisition.gov/.

52.203-2 Certificate of Independent Price Determination (Apr 1985)

52.203-7 Anti-Kickback Procedures (Jun 2020)

52.203-11 Certification and Disclosure Regarding Payments to Influence Certain Federal Transactions (Sep 2024)

52.203-12 Limitation on Payments to Influence Certain Federal Transactions (Jun 2020)

52.203-18 Prohibition on Contracting with Entities that Require Certain Internal Confidentiality Agreements or Statements-

Representation (Jan 2017)

52.203-19 Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (Jan 2017)

52.204-7 System for Award Management-Registration. (Deviation 2026-O0038)

52.204-9 Personal Identity Verification of Contractor Personnel (Jan 2011)

52.204-10 Reporting Executive Compensation and First-Tier Subcontract Awards. (Deviation 2026-O0038)

52.204-13 System for Award Management-Maintenance. (Deviation 2026-O0038)

52.204-19 Incorporation by Reference of Representations and Certifications (Dec 2014)

52.204-91 (DEV) Contractor Identification (Deviation 2026-O0043)

52.209-2 Prohibition on Contracting With Inverted Domestic Corporations-Representation. (Deviation 2026-O0038)

52.209-6 Protecting the Government's Interest When Subcontracting With Contractors Debarred, Suspended, Proposed for

Debarment, or Voluntarily Excluded. (Deviation 2026-O0038)

52-209-10 Prohibition on Contracting With Inverted Domestic Corporations. (Deviation 2026-O0038)

52.209-11 Representation by Corporations Regarding Delinquent Tax Liability or a Felony Conviction under any Federal Law.

(Deviation 2026-O0038)

52.212-1 Instructions to Offerors—Commercial Products and Commercial Services (Sep 2023)

52.217-5 Evaluation of Options (July 1990)

52.219-6 Notice of Total Small Business Set-Aside. (Deviation 2026-O0038)

52.219-28 Postaward Small Business Program Representation. (Deviation 2026-O0038)

52.222-3 Convict Labor. (Deviation 2026-O0038)

52.222-20 Contracts for Materials, Supplies, Articles, and Equipment. (Deviation 2026-O0038)

52.222-35 Equal Opportunity for Veterans. (Deviation 2026-O0038)

52.222-36 Equal Opportunity for Workers with Disabilities. (Deviation 2026-O0038)

52.222-37 Employment Reports on Veterans. (Deviation 2026-O0038)

52.222-41 Service Contract Labor Standards (Aug 2018)

52.222-43 Fair Labor Standards Act and Service Contract Labor Standards -- Price Adjustment (Multiple Year and Option

Contracts) (Aug 2018)

52.222-50 Combating Trafficking in Persons. (Deviation 2026-O0038)

52.222-54 Employment Eligibility Verification. (Deviation 2026-O0038)

52.222-55 Minimum Wages for Contractor Workers Under Executive Order 14026. (Deviation 2026-O0038)

52.222-62 Paid Sick Leave Under Executive Order 13706. (Deviation 2026-O0038)

52.222-90 Addressing DEI Discrimination by Federal Contractors. (Deviation 2026-O0040, Revision 1)

52.223-5 Pollution Prevention and Right-to-Know Information (May 2024)

52.223-23 Sustainable Products. (Deviation 2026-O0038)

52.226-7 Drug-Free Workplace (May 2024)

52.226-8 Encouraging Contractor Policies to Ban Text Messaging While Driving (May 2024)

52.232-23 Alt I Assignment of Claims (May 2014)

52.232-29 Terms for Financing of Purchases of Commercial Products and Commercial Services (Nov 2021)

52.232-33 Payment by Electronic Funds Transfer-System for Award Management (Oct 2018)

52.232-39 Unenforceability of Unauthorized Obligations (Jun 2013)

52.232-40 Providing Accelerated Payments to Small Business Subcontractors (Mar 2023)

52.233-1 Disputes. (Deviation 2026-O0038)

52.233-2 Service of Protest. (Deviation 2026-O0038)

52.233-3 Protest after Award. (Deviation 2026-O0038)

52.233-4 Applicable Law for Breach of Contract Claim. (Deviation 2026-O0038)

52.237-2 Protection of Government Buildings, Equipment, and Vegetation (Apr 1984)

52.240-90 Security Prohibitions and Exclusions Representations and Certifications. (Deviation 2026-O0038)

52.240-91 Security Prohibitions and Exclusions. (Deviation 2026-O0038)

Issued on: October 19, 2026

52.244-6 Subcontracts for Commercial Products and Commercial Services (2026)

52.246-4 Inspection of Services-Fixed-Price (Aug 1996)

52.247-34 F.o.b. Destination (Nov 1991)

252.201-7000 CONTRACTING OFFICER'S REPRESENTATIVE (DEC 1991)

252.203-7000 REQUIREMENTS RELATING TO COMPENSATION OF FORMER DOD OFFICIALS (SEP 2011)

252.203-7002 REQUIREMENT TO INFORM EMPLOYEES OF WHISTLEBLOWER RIGHTS (DEC 2022)

252.203-7005 REPRESENTATION RELATING TO COMPENSATION OF FORMER DOD OFFICIALS (SEP 2022)

252.204-7003 CONTROL OF GOVERNMENT PERSONNEL WORK PRODUCT (APR 1992)

252.204-7004 ANTITERRORISM AWARENESS TRAINING FOR CONTRACTORS (JAN 2023)

252.204-7008 COMPLIANCE WITH SAFEGUARDING COVERED DEFENSE INFORMATION CONTROLS (OCT 2016)

252.204-7009 LIMITATIONS ON THE USE OR DISCLOSURE OF THIRD-PARTY CONTRACTOR REPORTED CYBER

INCIDENT INFORMATION (JAN 2023)

252.204-7012 SAFEGUARDING COVERED DEFENSE INFORMATION AND CYBER INCIDENT REPORTING (MAY

2024)

252.204-7016 COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES—REPRESENTATION (DEC

2019)

252.204-7018 PROHIBITION ON THE ACQUISITION OF COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT

OR SERVICES (JAN 2023)

252.204-7019 NOTICE OF NIST SP 800–171 DOD ASSESSMENT REQUIREMENTS (NOV 2023)

252.204-7020 NIST SP 800-171 DOD ASSESSMENT REQUIREMENTS (NOV 2023)

252.204-7022 EXPEDITING CONTRACT CLOSEOUT (MAY 2021)

252.204-7024 NOTICE ON THE USE OF THE SUPPLIER PERFORMANCE RISK SYSTEM (MAR 2023)

252.209-7004 SUBCONTRACTING WITH FIRMS THAT ARE OWNED OR CONTROLLED BY THE GOVERNMENT OF A

COUNTRY THAT IS A STATE SPONSOR OF TERRORISM (MAY 2019)

252.209-7011 REPRESENTATION FOR RESTRICTION ON THE USE OF CERTAIN INSTITUTIONS OF HIGHER

EDUCATION (AUG 2025)

252.209-7012 PROHIBITION RELATING TO CONFLICTS OF INTEREST IN CONSULTING SERVICES—

CERTIFICATION (OCT 2025)

252.215-7010 REQUIREMENTS FOR CERTIFIED COST OR PRICING DATA AND DATA OTHER THAN CERTIFIED

COST OR PRICING DATA—BASIC (MAY 2024)

252.215-7013 SUPPLES AND SERVICES PROVIDED BY NONTRADITIONAL DEFENSE CONTRACTORS (JAN 2023)

252.223-7006 PROHIBITION ON STORAGE, TREATMENT, AND DISPOSAL OF TOXIC OR HAZARDOUS

MATERIALS—BASIC (SEP 2014)

252.223-7008 PROHIBITION OF HEXAVALENT CHROMIUM (JAN 2023)

252.225-7000 BUY AMERICAN—BALANCE OF PAYMENTS PROGRAM CERTIFICATE—BASIC (FEB 2024)

252.225-7002 QUALIFYING COUNTRY SOURCES AS SUBCONTRACTORS (MAR 2022)

252.225-7012 PREFERENCE FOR CERTAIN DOMESTIC COMMODITIES (APR 2022)

252.225-7048 EXPORT CONTROLLED ITEMS (JUNE 2013)

252.225-7055 REPRESENTATION REGARDING BUSINESS OPERATIONS WITH THE MADURO REGIME (MAY 2022)

252.225-7056 PROHIBITION REGARDING BUSINESS OPERATIONS WITH THE MADURO REGIME (JAN 2023)

252.225-7060 PROHIBITION ON CERTAIN PROCUREMENTS FROM THE XINJIANG UYGHUR AUTONOMOUS

REGION (JUN 2023)

252.225-7972 (DEV) PROHIBITION ON THE PROCUREMENT OF FOREIGN-MADE UNMANNED AIRCRAFT

SYSTEMS (MAY 2020) (DEVIATION 2020-O0015)

252.232-7003 ELECTRONIC SUBMISSION OF PAYMENT REQUESTS AND RECEIVING REPORTS (DEC 2018)

252.232-7004 Alt I DOD PROGRESS PAYMENT RATES. (OCT 2014)

252.232-7010 LEVIES ON CONTRACT PAYMENTS (DEC 2006)

252.237-7010 PROHIBITION ON INTERROGATION OF DETAINEES BY CONTRACTOR PERSONNEL (JAN 2023)

252.243-7001 PRICING OF CONTRACT MODIFICATIONS (DEC 1991)

252.243-7002 REQUESTS FOR EQUITABLE ADJUSTMENT (DEC 2022)

252.244-7000 SUBCONTRACTS FOR COMMERCIAL PRODUCTS OR COMMERCIAL SERVICES ( NOV 2023 )

252.247-7023 TRANSPORTATION OF SUPPLIES BY SEA—BASIC (OCT 2024)

252.270-7000 PILOT PROGRAM TO INCENTIVIZE CONTRACTING WITH EMPLOYEE-OWNED BUSINESSES-

REPRESENTATION. (NOV 2024)

252.270-7001 PILOT PROGRAM TO INCENTIVIZE CONTRACTING WITH EMPLOYEE-OWNED BUSINESSES-

SUBCONTRACTING CERTIFICATION.

Issued on: October 19, 2026

252.270-7002 PILOT PROGRAM TO INCENTIVIZE CONTRACTING WITH EMPLOYEE-OWNED BUSINESSES. (NOV

2024)

5. PROVISION/ CLAUSES INCORPORATED BY FULL TEXT (FT)

52.212-4 Terms and Conditions—Commercial Products and Commercial Services (FEB 2026)

(a) Definitions. The clause at Federal Acquisition Regulation (FAR) 52.202-1, Definitions, is incorporated by reference.

(b) Inspection/Acceptance. The Contractor shall only tender for acceptance those items that conform to the requirements of this contract. The Government reserves the right to inspect or test any supplies or services that have been tendered for acceptance. The

Government may require repair or replacement of nonconforming supplies or reperformance of nonconforming services at no increase in contract price. If repair/replacement or reperformance will not correct the defects or is not possible, the Government may seek an equitable price reduction or adequate consideration for acceptance of nonconforming supplies or services. The Government must exercise its post acceptance rights—

(1) Within a reasonable time after the defect was discovered or should have been discovered; and

(2) Before any substantial change occurs in the condition of the item, unless the change is due to the defect in the item.

(c) Assignment. The Contractor or its assignee may assign its rights to receive payment due as a result of performance of this contract to a bank, trust company, or other financing institution, including any Federal lending agency in accordance with the Assignment of

Claims Act (31 U.S.C. 3727). However, when a third party makes payment (e.g., use of the Governmentwide commercial purchase card), the Contractor may not assign its rights to receive payment under this contract.

(d) Changes. Changes in the terms and conditions of this contract may be made only by written agreement of the parties.

(e) Disputes. This contract is subject to 41 U.S.C. chapter 71, Contract Disputes. Failure of the parties to this contract to reach agreement on any request for equitable adjustment, claim, appeal, or action arising under or relating to this contract shall be a dispute to be resolved in accordance with the clause FAR 52.233-1, Disputes, which is incorporated in this contract by reference. The

Contractor shall proceed diligently with performance of this contract, pending final resolution of any dispute arising under the contract.

(f) Excusable delays. The Contractor shall be liable for default unless nonperformance is caused by an occurrence beyond the reasonable control of the Contractor and without its fault or negligence. Examples of occurrences include acts of God or the public enemy, acts of the Government in either its sovereign or contractual capacity, fires, floods, epidemics, quarantine restrictions, strikes, unusually severe weather, and delays of common carriers. When an excusable delay occurs, the Contractor shall—

(1) Notify the Contracting Officer in writing as soon as possible;

(2) Remedy the delay as quickly as possible; and

(3) Notify the Contracting Officer when the occurrence is over.

(g) Invoice. The Government will handle invoices according to the Prompt Payment Act (31 U.S.C. 3903) and 5 CFR part 1315. The

Contractor shall submit invoices to the address designated in the contract to receive invoices. An invoice must include the information required by 5 CFR part 1315.9(b).

(h) Patent indemnity. The Contractor shall indemnify the Government and its officers, employees, and agents against liability, including costs, for actual or alleged direct or contributory infringement of, or inducement to infringe, any United States or foreign patent, trademark, or copyright, arising out of the performance of this contract, provided the Contractor is reasonably notified of such claims and proceedings.

(i) Payment—

(1) Items accepted. Payment shall be made for items accepted by the Government that have been delivered to the delivery destinations set forth in this contract.

(2) Prompt payment. The Government will make payment in accordance with the Prompt Payment Act ( 31 U.S.C. 3903) and prompt payment regulations at 5 CFR part 1315.

(3) Discount. In connection with any discount offered for early payment, time shall be computed from the date of the invoice.

For the purpose of computing the discount earned, payment shall be considered to have been made on the date that appears on the payment check or the specified payment date if an electronic funds transfer payment is made.

(4) Overpayments. If the Contractor becomes aware of a duplicate contract financing or invoice payment or that the

Government has otherwise overpaid on a contract financing or invoice payment, the Contractor shall—

(i) Remit the overpayment amount to the payment office cited in the contract along with a description of the overpayment including the—

(A) Circumstances of the overpayment (e.g., duplicate payment, erroneous payment, liquidation errors, date(s) of overpayment);

Issued on: October 19, 2026

(B) Affected contract number and delivery order number, if applicable;

(C) Affected line item or subline item, if applicable;

(D) Contractor point of contact; and

(ii) Provide a copy of the remittance and supporting documentation to the Contracting Officer.

(5) Interest.

(i) All amounts that become payable by the Contractor to the Government under this contract shall bear simple interest from the date due until paid unless paid within 30 days of becoming due. The interest rate shall be the interest rate established by the Secretary of the Treasury as provided in 41 U.S.C. 7109, which is applicable to the period in which the amount becomes due, as provided in (i)(6)(v) of this clause, and then at the rate applicable for each six-month period as fixed by the Secretary until the amount is paid.

(ii) The Government may issue a demand for payment to the Contractor upon finding a debt is due under the contract.

(iii) Final decisions. The Contracting Officer will issue a final decision as required by FAR part 33 if–

(A) The Contracting Officer and the Contractor are unable to reach agreement on the existence or amount of a debt within 30 days;

(B) The Contractor fails to liquidate a debt previously demanded by the Contracting Officer within the timeline specified in the demand for payment unless the amounts were not repaid because the Contractor has requested an installment payment agreement; or

(C) The Contractor requests a deferment of collection on a debt previously demanded by the Contracting

Officer (see FAR part 32).

(iv) If a demand for payment was previously issued for the debt, the demand for payment included in the final decision shall identify the same due date as the original demand for payment.

(v) Amounts shall be due at the earliest of the following dates:

(A) The date fixed under this contract.

(B) The date of the first written demand for payment, including any demand for payment resulting from a termination for cause.

(vi) The interest charge shall be computed for the actual number of calendar days involved beginning on the due date and ending on-

(A) The date on which the designated office receives payment from the Contractor;

(B) The date of issuance of a Government check to the Contractor from which an amount otherwise payable has been withheld as a credit against the contract debt; or

(C) The date on which an amount withheld and applied to the contract debt would otherwise have become payable to the Contractor.

(vii) The interest charge made under this clause may be reduced under the procedures for interest credits prescribed in FAR part 32 in effect on the date of this contract.

(j) Risk of loss. Unless the contract specifically provides otherwise, risk of loss or damage to the supplies provided under this contract shall remain with the Contractor until, and shall pass to the Government upon—

(1) Delivery of the supplies to a carrier, if transportation is f.o.b. origin; or

(2) Delivery of the supplies to the Government at the destination specified in the contract, if transportation is f.o.b.

destination.

(k) Taxes. The contract price includes all applicable Federal, State, and local taxes and duties.

(l) Termination for the Government’s convenience. The Government reserves the right to terminate this contract, or any part hereof, for its sole convenience. In the event of such termination, the Contractor shall immediately stop all work and shall immediately cause any and all of its suppliers and subcontractors to cease work. Subject to the terms of this contract, the Contractor shall be paid a percentage of the contract price reflecting the percentage of the work performed prior to the notice of termination, plus reasonable charges the Contractor can demonstrate to the satisfaction of the Government using its standard record keeping system, have resulted from the termination. The Contractor shall not be required to comply with the cost accounting standards or contract cost principles for this purpose. This paragraph does not give the Government any right to audit the Contractor’s records. The Contractor shall not be paid for any work performed or costs incurred which reasonably could have been avoided.

(m) Termination for cause. The Government may terminate this contract, or any part hereof, for cause in the event of any default by the Contractor, or if the Contractor fails to comply with any contract terms and conditions, or fails to provide the Government, upon request, with adequate assurances of future performance. The Government will send a cure notice to the Contractor, unless the reason for the termination is late delivery. In the event of termination for cause, the Government shall not be liable to the Contractor for any amount for supplies or services not accepted, and the Contractor shall be liable to the Government for any and all rights and remedies provided by law. If it is determined that the Government improperly terminated this contract for default, such termination shall be deemed a termination for convenience.

Issued on: October 19, 2026

(n) Title. Unless specified elsewhere in this contract, title to items furnished under this contract shall pass to the Government upon acceptance, regardless of when or where the Government takes physical possession.

(o) Warranty. The Contractor warrants and implies that the items delivered under this contract are merchantable and fit for use for the particular purpose described in this contract.

(p) Limitation of liability. Except as otherwise provided by an express warranty, the Contractor will not be liable to the Government for consequential damages resulting from any defect or deficiencies in accepted items.

(q) Compliance with laws unique to Government contracts. The Contractor agrees to comply with 31 U.S.C. 1352 relating to limitations on the use of appropriated funds to influence certain Federal contracts; 40 U.S.C. chapter 37, Contract Work Hours and

Safety Standards; 41 U.S.C. chapter 87, Kickbacks; 49 U.S.C. 40118, Government-financed air transportation; and 41 U.S.C. chapter

21 relating to procurement integrity.

(r) Order of precedence. Any inconsistencies in this solicitation or contract shall be resolved by giving precedence in the following order:

(1) The schedule of supplies/services;

(2) The Disputes, Payments, Invoice, Compliance with Laws Unique to Government Contracts, and Unauthorized

Obligations paragraphs of this clause;

(3) Other contract clauses incorporated in the solicitation or contract;

(4) Addenda to this solicitation or contract;

(5) Solicitation provisions incorporated in the solicitation;

(6) Other paragraphs of this clause;

(7) Other documents, exhibits, and attachments; and

(8) The specification.

(s) Unauthorized obligations.

(1) Except as stated in paragraph (s)(2) of this clause, when any supply or service acquired under this contract is subject to any End User License Agreement (EULA), Terms of Service (TOS), or similar legal instrument or agreement, that includes any clause requiring the Government to indemnify the Contractor or any person or entity for damages, costs, fees, or any other loss or liability that would create an Anti-Deficiency Act violation (31 U.S.C. 1341), the following shall govern:

(i) Any such clause is unenforceable against the Government.

(ii) Neither the Government nor any Government-authorized end user shall be deemed to have agreed to such clause by virtue of it appearing in the EULA, TOS, or similar legal instrument or agreement. If the EULA, TOS, or similar legal instrument or agreement is invoked through an “I agree” click box or other comparable mechanism (e.g., “click-wrap” or “browse-wrap” agreements), execution does not bind the Government or any Government authorized end user to such clause.

(iii) Any such clause is deemed to be stricken from the EULA, TOS, or similar legal instrument or agreement.

(2) Paragraph (s)(1) of this clause does not apply to indemnification by the Government that is expressly authorized by statute and specifically authorized under applicable agency regulations and procedures.

(t) Comptroller General examination of record. This paragraph applies if this contract was awarded using other than sealed bid procedures and is in excess of the simplified acquisition threshold on the date of award of this contract.

(1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor’s directly pertinent records involving transactions related to this contract.

(2) The Contractor shall make available at its offices, at all reasonable times, the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in

FAR part 4, longer period required by statute, or periods specified in other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved.

(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This clause does not require the Contractor to create or maintain any record that the

Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.

(u) Incorporation by reference. The Contractor’s representations and certifications, including those completed electronically via the

System for Award Management (SAM), are incorporated by reference into the contract.

(End of clause)

52.217-9 Option to Extend the Term of the Contract (Mar 2000)

Issued on: October 19, 2026

(a) The Government may extend the term of this contract by written notice to the Contractor within 7 calendar days; provided that the

Government gives the Contractor a preliminary written notice of its intent to extend at least 60 days before the contract expires. The preliminary notice does not commit the Government to an extension.

(b) If the Government exercises this option, the extended contract shall be considered to include this option clause.

(c) The total duration of this contract, including the exercise of any options under this clause, shall not exceed 5 years (months)

(years).

52.222-42 Statement of Equivalent Rates for Federal Hires (May 2014)

In compliance with the Service Contract Labor Standards statute and the regulations of the Secretary of Labor ( 29 CFR Part 4), this clause identifies the classes of service employees expected to be employed under the contract and states the wages and fringe benefits payable to each if they were employed by the contracting agency subject to the provisions of 5 U.S.C.5341 or 5332.

This Statement is for Information Only: It is not a Wage Determination

Employee Class Monetary Wage-Fringe Benefits

23040 Aircraft Mechanic Helper_

$21.89/ hour – HEALTH & WELFARE EO 13706: $5.42 per hour, up to 40 hours per week, or $216.80 per week, or $939.46 per month

23060 Aircraft Servicer_

$26.95/ hour – HEALTH & WELFARE EO 13706: $5.42 per hour, up to 40 hours per week, or $216.80 per week, or $939.46 per month

23080 Aircraft Worker_

$29.47/ hour – HEALTH & WELFARE EO 13706: $5.42 per hour, up to 40 hours per week, or $216.80 per week, or $939.46 per month

52.228-5 Insurance-Work on a Government Installation.

Insurance-Work on a Government Installation (Jan 1997)

(a) The Contractor shall, at its own expense, provide and maintain during the entire performance of this contract, at least the kinds and minimum amounts of insurance required in the Schedule or elsewhere in the contract.

(b) Before commencing work under this contract, the Contractor shall notify the Contracting Officer in writing that the required insurance has been obtained. The policies evidencing required insurance shall contain an endorsement to the effect that any cancellation or any material change adversely affecting the Government’s interest shall not be effective-

(1) For such period as the laws of the State in which this contract is to be performed prescribe; or

(2) Until 30 days after the insurer or the Contractor gives written notice to the Contracting Officer, whichever period is longer.

(c) The Contractor shall insert the substance of this clause, including this paragraph (c), in subcontracts under this contract that require work on a Government installation and shall require subcontractors to provide and maintain the insurance required in the Schedule or elsewhere in the contract. The Contractor shall maintain a copy of all subcontractors’ proofs of required insurance, and shall make copies available to the Contracting Officer upon request.

52.252-1 Solicitation Provisions Incorporated by Reference (Feb 1998) http://uscode.house.gov/view.xhtml?req=granuleid:USC-prelim-title5-section5341&num=0&edition=prelim

Issued on: October 19, 2026

This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/this address:

https://www.acquisition.gov/

(End of provision)

52.252-2 Clauses Incorporated By Reference (Feb 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this address: https://www.acquisition.gov/

52.252-5 Authorized Deviations in Provisions (Nov 2020)

(a) The use in this solicitation of any Federal Acquisition Regulation (48 CFR Chapter 1) provision with an authorized deviation is indicated by the addition of "(DEVIATION)" after the date of the provision.

(b) The use in this solicitation of any Defense Federal Acquisitions Regulation Supplements (DFARS) (48 CFR Chapter 2) provision with an authorized deviation is indicated by the addition of "(DEVIATION)" after the name of the regulation.

52.252-6 Authorized Deviations in Clauses (Nov 2020)

(a) The use in this solicitation or contract of any Federal Acquisition Regulation (48 CFR Chapter 1) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the date of the clause.

(b) The use in this solicitation or contract of any Defense Federal Acquisitions Regulation Supplements (DFARS) (48 CFR 2) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the name of the regulation.

252.204-7017 PROHIBITION ON THE ACQUISITION OF COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR

SERVICES—REPRESENTATION (MAY 2021)

The Offeror is not required to complete the representation in this provision if the Offeror has represented in the provision at 252.204-

7016 , Covered Defense Telecommunications Equipment or Services—Representation, that it “does not provide covered defense telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument.”

(a) Definitions. “Covered defense telecommunications equipment or services,” “covered mission,” “critical technology,” and

“substantial or essential component,” as used in this provision, have the meanings given in the 252.204-7018 clause, Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services, of this solicitation.

(b) Prohibition. Section 1656 of the National Defense Authorization Act for Fiscal Year 2018 (Pub. L. 115-91) prohibits agencies from procuring or obtaining, or extending or renewing a contract to procure or obtain, any equipment, system, or service to carry out covered missions that uses covered defense telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system.

(c) Procedures. The Offeror shall review the list of excluded parties in the System for Award Management (SAM) at https://www.sam.gov for entities that are excluded when providing any equipment, system, or service to carry out covered missions that uses covered defense telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system, unless a waiver is granted.

(d) Representation. If in its annual representations and certifications in SAM the Offeror has represented in paragraph (c) of the provision at 252.204-7016 , Covered Defense Telecommunications Equipment or Services—Representation, that it “does” provide covered defense telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument, then the Offeror shall complete the following additional representation:

Issued on: October 19, 2026

The Offeror represents that it [ ] will [ ] will not provide covered defense telecommunications equipment or services as a part of its offered products or services to DoD in the performance of any award resulting from this solicitation.

(e) Disclosures. If the Offeror has represented in paragraph (d) of this provision that it “will provide covered defense telecommunications equipment or services,” the Offeror shall provide the following information as part of the offer:

(1) A description of all covered defense telecommunications equipment and services offered (include brand or manufacturer; product, such as model number, original equipment manufacturer (OEM) number, manufacturer part number, or wholesaler number; and item description, as applicable).

(2) An explanation of the proposed use of covered defense telecommunications equipment and services and any factors relevant to determining if such use would be permissible under the prohibition referenced in paragraph (b) of this provision.

(3) For services, the entity providing the covered defense telecommunications services (include entity name, unique entity identifier, and Commercial and Government Entity (CAGE) code, if known).

(4) For equipment, the entity that produced or provided the covered defense telecommunications equipment (include entity name, unique entity identifier, CAGE code, and whether the entity was the OEM or a distributor, if known).

252.228-7001 Ground and Flight Risk (MAR 2023).

(a) Definitions. As used in this clause—

“Aircraft” means, unless otherwise provided in the contract Schedule, any item, other than a rocket or missile, intended for flight (e.g., fixed-winged aircraft, blended wing/lifting bodies, helicopters, vertical take-off or landing aircraft, lighter-than-air airships, and unmanned aerial vehicles), including emerging technologies that would commonly be considered aircraft. New production articles become aircraft at a stage of manufacture or production when a wing, portion of a wing, or engine is attached to a fuselage. Blended wing/lifting bodies become aircraft at a stage of manufacture or production when the center portion and a lifting surface become attached.

“Contractor’s managerial personnel” means the Contractor’s directors, officers, managers, superintendents, or equivalent representatives who have supervision or direction of—

(1) All, or substantially all, of the Contractor’s business;

(2) All, or substantially all, of the Contractor’s operation at any one plant or separate location; or

(3) A separate and complete major industrial operation.

“Contractor's premises” means those premises, including subcontractors’ premises, designated in the Schedule or in writing by the Contracting Officer, and any other place the aircraft is moved for safeguarding.

“Covered aircraft” means an aircraft owned by or to be delivered to the Government and, when determined by the contracting officer and specifically identified as such in the contract Schedule, may include contractor-furnished aircraft that are not intended for induction into the DoD inventory, including—

(1) Aircraft furnished by the Government to the Contractor under this contract while in the Contractor’s possession, care, custody, or control regardless of their location or state of disassembly or reassembly;

(2) Items removed from a Government-furnished aircraft that are—

(i) Intended for reinstallation on that particular aircraft, which retain their status as covered aircraft while awaiting installation; and

(ii) Not intended for reinstallation on that particular aircraft, which lose their status as covered aircraft once removal is complete;

(3) New production aircraft when wholly outside of buildings on the Contractor’s premises or other places described in the Schedule

(e.g., hush houses, run stations, and paint facilities); and

(4) Commercial aircraft, to include commercially available off-the-shelf aircraft, become covered aircraft when the commercial aircraft arrives at the Contractor’s place of performance for modification under the terms of the contract.

“Crewmember” means, unless otherwise provided in the Schedule, personnel required in the flight manual, assigned for the purpose of conducting any flight on behalf of the Contractor. It also includes any operator of an unmanned aerial vehicle.

“Flight” means any flight approved in writing by the Government flight representative, to include taxi test made in the performance of this contract, or flight for the purpose of safeguarding the aircraft. All aircraft off the Contractor's premises shall be considered to be in flight when on the ground or water for reasonable periods of time following emergency landings, landings made in performance of the contract, or landings approved in writing by the contracting officer.

“Workmanship error” means damage to the aircraft that is the result of an incorrectly performed skill-based task, operation, or action that was originally planned or intended.

(b) Combined regulation/instruction. The Contractor shall be bound by the operating procedures contained in the combined regulation/instruction entitled “Contractor’s Flight and Ground Operations” (Air Force Instruction 10-220, Army

Regulation 95-20, NAVAIR Instruction 3710.1 (Series), Coast Guard Instruction

Issued on: October 19, 2026

M13020.3 (Series), and Defense Contract Management Agency Instruction 8210-1 (Series)) in effect on the date of contract award.

Compliance with the combined regulation/instruction is required from the time of contract award throughout the period of performance of the contract, regardless of the Government’s assumption of risk under the contract.

(c) Government as self-insurer. The Government self-insures and assumes the risk of damage to, or loss or destruction of, covered aircraft subject to the following conditions:

(1) The Contractor’s liability to the Government for damage, loss, or destruction of covered aircraft is limited to the Contractor’s share of loss as defined at paragraph (h) of this clause, except when one of the exclusions at paragraph (d) applies.

(2) The liability provisions of this clause take precedence over the liability provisions of Federal Acquisition Regulation (FAR) clause

52.245-1, Government Property, with respect to covered aircraft.

(3) The Contractor is not liable for loss, damage, or destruction of covered aircraft as the result of normal wear and tear, or intentional damage or destruction as required in the Schedule.

(4) Conditions for Government assumption of risk in flight are as follows:

(i) The Contractor’s crewmembers are approved in writing by the Government flight representative (GFR).

(ii) The flight is approved in writing by the GFR.

(d) Exclusions from the Government’s assumption of risk. The Government’s assumption of risk under this clause shall not extend to damage, loss, or destruction of covered aircraft which—

(1) Is the result of willful misconduct or lack of good faith on the part of the Contractor’s managerial personnel, including the

Contractor’s oversight of subcontractors;

(2) Is sustained during flight if either the flight or the crewmembers have not been approved in advance and in writing by the GFR, who has been authorized in accordance with the combined regulation/instruction entitled “Contractor’s Flight and Ground Operations”;

(3) Occurs in the course of transportation by rail, or by conveyance on public streets, highways, or waterways, unless the transportation is limited to the vicinity of the Contractor’s premises, and incidental to work performed under the contract as described in the Schedule;

(4) Is covered by insurance;

(5) Occurs after the Contracting Officer has, in writing, revoked the Government’s assumption of risk in accordance…