Attachment_A_SPE600-17-R-0223.pdf

SPE600-17-R-0223

ATTACHMENT A

A-1

SECTION E

INSPECTION AND ACCEPTANCE

FAR 52.246-2 INSPECTION OF SUPPLIES -- FIXED-PRICE is incorporated by reference

E-0003 / E35 NONCONFORMING SUPPLIES AND SERVICES (DLA ENERGY DEC 2011)

(a) DEFINITION: As used in this contract provision:

Deviation is defined as a written authorization granted after contract award and prior to manufacture of an item, to depart from a particular performance or design requirement of a contract, specification, or referenced document, for a specific number of units or specific period of time, normally the duration of the contract.

Extraordinary situation means the matter cannot await resolution until the next DLA Energy business day (0800 to 1630 hours EST, Monday through Friday, Federal Holidays excluded).

Waiver is defined as a written authorization granted after contract award to accept a configuration item or other designated item which, during production or after having been submitted for inspection, is found to depart from specified requirements, but nevertheless is considered suitable for use “as is” or after repair by an approved method. Approval is on a case-by-case basis and is normally for a set period of time.

(b) The Government may, at its discretion, accept nonconforming supplies or services. In such cases, the Contractor must obtain a deviation or waiver from the Contracting Officer prior to acceptance.

(c) The following procedures shall be used to request a deviation or waiver.

(1) Requests for deviations and waivers shall be submitted by the Contractor to the Contracting Officer with a copy to the appropriate Inspection Office referenced in the LIST OF INSPECTION OFFICES FOR DLA ENERGY CONTRACTS or QUALITY REPRESENTATIVE contract provision of this contract. Each request shall provide the following information: Contractor name; name and contact information of the contractor’s authorized negotiator; contract number; contract line item number and product nomenclature, clause or contract provision number, paragraph and subparagraph, as appropriate; the nature of the request; the reason for the request; the corrective action being taken by the Contractor to correct and prevent recurrence of the condition(s) causing the nonconformance; and an agreement to pay an equitable price reduction, estimated and proposed by DLA Energy, over and above the administrative fee, contingent on the impact of the specific circumstances on DLA Energy relative to approval of the deviation or waiver.

(2) In extraordinary situations, the Contractor may initially submit a verbal request for a waiver, but not a deviation, to the Contracting Officer. Written requests shall be submitted to the Contracting Officer by the next DLA Energy business day (0800 to 1630 hours EST, Monday through Friday, Federal Holidays excluded). If the Contracting Officer cannot be reached, the Duty Officer shall be contacted to provide the necessary information to the proper individuals as soon as possible. The Duty Officer's telephone number is (800) 286-7633 or

(703) 767-8420.

(3) If a deviation or waiver is granted, the contract will be modified to accept the nonconforming supplies or services and to require the Contractor to provide an equitable price reduction or other adequate consideration commensurate with the deviation or waiver being granted. If the situation warrants, a deviation or waiver may be granted without prior agreement on price reduction or other consideration, subject to agreement by the Contractor, or its representative, to subsequent negotiation. Such an agreement, in addition to a brief description of the terms of the deviation or waiver, shall be documented on the shipping document or other appropriate correspondence. After negotiations, failure to agree on adequate consideration shall be a dispute concerning a question of fact within the meaning of the Disputes paragraph of the CONTRACT TERMS AND CONDITIONS – COMMERCIAL ITEMS contract provision of this contract.

(4) If a deviation or waiver is granted and the nonconforming supplies are accepted, then in no event will consideration be less than $500, which covers administrative costs, plus any additional cost of Government reinspection or retest, if necessary.

(5) If a deviation or waiver is granted modifying this contract, but the supplies accepted are subsequently determined to be in conformity with contract specifications, the Contractor shall still be obligated to pay the consideration originally agreed upon in support of the deviation or waiver. If, however, this consideration exceeds $1000, a second contract modification shall be issued reducing the Contractor's obligation to $1000 (the administrative cost of issuing the two required modifications), plus, if appropriate, any cost of Government reinspection or retest performed as a result of the deviation or waiver being granted.

(d) When notification of nonconforming supplies is received after the supplies have been accepted, and the Government determines not to exercise its right to reject or to require correction under the INSPECTION OF SUPPLIES – FIXED-PRICE, INSPECTION OF SERVICES – FIXED PRICE, or CONTRACT TERMS AND CONDITIONS – COMMERCIAL ITEMS contract provision, then in no event will consideration be less than $500 to cover administrative costs. This $500 fee is in addition to—

(1) Consideration commensurate with the extent of nonconforming supplies; and

(2) Cost of Government reinspection or retest, if necessary.

The administrative fee will apply to each claim letter issued for off-specification product delivered to an activity.

(e) Contractors shall be held responsible for payment of any fines or penalties imposed on a receiving activity by an environmental enforcement agency, resulting from the delivery of nonconforming supplies under a DLA Energy contract.

A-2

(f) Repeated tender of nonconforming supplies or services, including those with only minor defects, will be discouraged by appropriate actions, including, but not limited to, rejecting the supplies or services whenever feasible and documenting the Contractor's performance records.

SECTION F

DELIVERIES OR PERFORMANCE

F-0001 / F1.01-1 DELIVERY CONDITIONS FOR TRANSPORT TRUCKS, TRUCKS AND TRAILERS,

AND TANK WAGONS (DLA ENERGY JAN 2012)

IMPORTANT NOTE on EPA TESTING OF UNDERGROUND TANKS. If the "volumetric" method is used for annual EPA testing of underground tanks, the "topping off" of tanks for this test is outside the scope of DLA Energy requirements contracts.

(a) F.O.B. ORIGIN. On items calling for delivery at Contractor's refinery, terminal, or bulk plant f.o.b. transport truck, truck and trailer, or tank wagon—

(1) Supplies ordered hereunder shall be delivered, at Contractor's expense, into equipment specified in the Schedule.

(2) Unless otherwise specified in the Schedule, all deliveries shall be made on the day specified in the delivery order unless otherwise authorized by the receiving activity during normal working hours of such activity, provided that the Contractor shall have received the order at least 48 hours prior to the day so specified.

(b) F.O.B. DESTINATION. On items calling for delivery f.o.b. destination by means of transport truck, truck and trailer, or tank wagon--

(1) The Contractor shall not be required to deliver by transport truck or truck and trailer a quantity less than a full load nor into more than one storage tank, with the following exceptions:

(i) An order placed under an item of this contract calling for delivery by transport truck of motor gasoline, fuel oil, diesel fuel, or kerosene, or, if this procurement is for Central America only, jet fuel, may require delivery of a quantity as low as 5,200 gallons whenever the activity is restricted either by a tank capacity or by a directive from receiving a larger quantity; and

(ii) Where the Schedule provides for multiple drop deliveries, the Contractor may be required to deliver into more than one storage tank. Where truck and trailer is the method of delivery specified, the Contractor may, at its option, make delivery by transport truck. In the case of deliveries in Alaska, where truck and trailer or transport truck is the method of delivery specified, the Contractor may, at its option, make delivery by tank wagon.

(2) Unless otherwise specified in the Schedule, all deliveries shall be made on the day specified in the delivery order unless otherwise authorized by the receiving activity during normal working hours of such activity, provided that the Contractor shall have received the order at least 48 hours prior to the day so specified.

(3) The Contractor shall not be required to deliver by tank wagon a quantity of less than 575 liters (or 150 gallons) but, at the Government's option, may be required to deliver into more than one storage tank.

(4) When delivery is made by tank wagon, such wagon shall be equipped with pump, meter, and a minimum of 100 feet (30 meters) of hose. Where delivery is made by transport truck or truck and trailer, such delivery equipment shall be equipped with a minimum of 15 feet of hose.

(5) When delivery is made by tank wagon, transport truck, or truck and trailer to a Government facility, the Contractor shall present delivery equipment and product in such condition at destination so as to permit complete off-loading within the prescribed free time.

(6) Unless otherwise provided in the Schedule, free time for unloading trucks, transport trucks, or trucks and trailers shall be unlimited.

(7) When delivery is made by tank wagon, transport truck, or truck and trailer to a Government facility—

(i) The Contractor shall provide properly maintained delivery equipment and properly trained delivery personnel to reasonably assure that delivery can be made without damage to vegetation and asphalt pavement adjacent to storage facilities being filled. The Contractor’s delivery personnel who have not exercised reasonable care and delivery equipment that is poorly maintained may be refused entrance to the installation by the installation Commander.

(ii) The Contractor shall present delivery equipment and product in such condition at destination so as to permit complete off-loading within the prescribed free time.

F-0002 / F1.09-2 DETERMINATION OF INVOICE QUANTITY (PC&S) (DLA ENERGY JAN 2012)

(a) QUANTITY. The quantity of supplies furnished under this contract shall be determined as follows:

(1) F.O.B. DESTINATION.

(i) DELIVERIES BY TANKER OR BARGE.

(A) On items requiring delivery on an f.o.b. destination basis by tanker or barge, the quantity shall be determined on the basis of--

(1) Calibrated meters on the receiving tank system; or

(2) Receiving tank measurements.

(B) All quantities shall be converted to net gallons at 60 degrees Fahrenheit (or liters at 15 degrees Celsius).

(ii) DELIVERIES BY RAIL TANK CAR.

(A) On items requiring delivery on an f.o.b. destination basis by rail tank car, the quantity of supplies furnished under this contract shall be determined (at the Government’s option) on the basis of--

A-3

(1) Calibrated meter on the receiving tank system;

(2) Weigh, using calibrated scales at the receiving location; or

(3) Receiving tank measurements.

(B) All quantities shall be converted to net gallons at 60 degrees Fahrenheit (or liters at 15 degrees Celsius).

(iii) DELIVERIES BY TANK TRUCK/TRUCK AND TRAILER/TANK WAGON.

(A) If the narrative requires a tank wagon (which is always equipped with a meter), that meter shall be used to determine quantity at time of delivery. The quantity shall be read directly from the meter. On items requiring delivery on a f.o.b. destination basis by tank truck or truck and trailer, quantity shall be determined in the following order of preference:

(1) Calibrated meter on the receiving tank system

(2) Calibrated meter on the conveyance

(3) Weight using calibrated scales at the receiving location.

(4) Loading rack meter ticket. The ticket must be generated at the time of loading and be based on a calibrated loading rack meter. The loading rack ticket shall be mechanically annotated with the gross and net gallons (or gross and net liters), the observed and corrected API gravity (or density), and the temperature at which the product was measured.

(5) Receipt tank measurements (as identified in the Schedule).

(B) All quantities, other than delivery by tank wagon, shall be converted, either mechanically or manually, to net gallons at

60 degrees Fahrenheit (or liters at 15 degrees Celsius).

(C) If a loading rack meter ticket is used to determine quantity for a biodiesel blend, the quantity shall be converted to net (volume corrected) gallons at 60 degrees Fahrenheit (or liters at 15 degrees Celsius). The Contractor shall prepare separate loading rack meter tickets for the diesel portion and for the biodiesel blend stock B100 (the industry designation for pure biodiesel), hereinafter referred to as the B100 portion of the load. The B100 loading rack meter shall be recorded at gross (ambient) temperature when the loading meter is not capable of providing a net (volume corrected) quantity. The total shall be the sum of the net diesel and gross B100. When the B100 loading rack meters are capable of providing a net (volume corrected) quantity, the total receipt quantity shall be the sum of the net diesel and the net B100.

(2) F.O.B. ORIGIN. All quantities shall be converted to net gallons at 60 degrees Fahrenheit (or liters at 15 degrees Celsius).

(i) DELIVERIES INTO TANKER OR BARGE. On items requiring delivery at the Contractor's refinery, terminal, or bulk plant on an f.o.b. origin basis into a tanker or barge, the quantity shall be determined (at the Contractor's option) on the basis of--

(A) Calibrated meter; or

(B) Shipping/shore tank measurement.

(ii) DELIVERIES INTO RAIL TANK CAR. On items requiring delivery at the Contractor’s refinery, terminal, or bulk plant on an f.o.b. origin basis, the quantity shall be determined (at the Contractor’s option) on the basis of--

(A) Certified loading rack meter;

(B) Weight, using calibrated scales; or

(C) Certified capacity tables for the rail tank car.

(iii) DELIVERIES BY TANK TRUCK/TRUCK AND TRAILER/TANK WAGON.

(A) On items requiring delivery at the Contractor's refinery, terminal, or bulk plant on an f.o.b. origin basis, the quantity shall be determined (at the Contractor's option) on the basis of--

(1) Calibrated loading rack meter;

(2) Weight, using calibrated scales; or

(3) Certified capacity tables of the conveyance loaded.

(B) WATER BOTTOMS.

(1) Every delivery must be free of all water bottoms prior to discharge; and

(2) The Contractor is responsible for their removal and disposal.

(b) MEASUREMENT RESTRICTIONS. All methods of measurements described in this contract provision are subject to government safety and environmental restrictions, foreign or domestic. Such restrictions may prohibit, or render ineffective, a particular method in some cases.

(c) MEASUREMENT STANDARDS. All measurements and calibrations made to determine quantity shall be in accordance with the most recent edition of the API Manual of Petroleum Measurement Standards (MPMS). Outside the United States, other technically equivalent national or international standards may be used. Certified capacity tables shall mean capacity tables prepared by an independent inspector or any independent surveyor to the aforementioned measurement and calibration standards. In addition, the following specific standards will be used as applicable:

(1) API MPMS Chapter 11.1, Temperature and Pressure Volume Correction Factors for Generalized Crude Oils, Refined Products, and Lubricating Oils (this chapter is an adjunct to ASTM D 1250, IP 200 and ISO 91-1). Either the 2004 or 1980 version of the standard may be used. Either the printed tables (an adjunct to the 1980 version) or the computer subroutine version of the standard may be used.

In case of disputes, the computer subroutine and the 2004 version of the standard will be the referee method.

(i) For crude oils, JP4, and Jet B, use Volume I, Tables 5A and 6A; Volume VII, Tables 53A and 54A; or Volume IV, Tables 23A and 24A.

(ii) For lubricating oils, use Volume XIII, Tables 5D and 6D; Volume XIV, Tables 53D and 54D; or Tables 23D and 24D (2004 version).

(iii) For all other fuels and fuel oils, use Volume II, Tables 5B and 6B; Volume VII, Tables 53B and 54B; or Volume V, Tables 23B and 24B.

(iv) For chemicals/additives, use Volume III, Table 6C (or Volume IX, Table 54C) or volume correct in accordance with the product specification.

(v) Volume XII, Table 52, shall be used to convert cubic meters at 15 degrees Celsius to barrels at 60 degrees Fahrenheit.

Convert liters at 15 degrees Celsius to cubic meters at 15 degrees Celsius by dividing by 1,000. Convert gallons at 60 degrees Fahrenheit to barrels at 60 degrees Fahrenheit by dividing by 42. Should foreign law restrict conversion by this method, the method required by law shall be used.

A-4

(vi) As an option to (c)(1)(v), liters may be converted to gallons using Table F1.09A (see below). If this option is used, it must be agreed upon by both parties and shall remain in effect for the duration of the contract. Should foreign law restrict conversion by this method, the method required by law shall be stated in the offer.

(vii) If the original measurement is by weight and quantity is required by U.S. gallons, then--

(A) Volume XI, Table 8, shall be used to convert pounds to U.S. gallons at 60 degrees Fahrenheit.

(B) Volume XII of the adjunct to ASTM D 1250, Table 58, shall be used to convert metric tons to U.S. gallons at 60 degrees Fahrenheit.

(2) API MPMS Chapter 4, Proving Systems. All meters used in determining product volume shall be calibrated using this standard with the frequency required by local regulation (foreign or domestic). If no local regulation exists, then the frequency of calibration shall be that recommended by the meter manufacturer or every 6 months, whichever is more frequent. A meter calibration log/calibration certificates shall be maintained which, as a minimum, contains--

(i) Number/name of each meter;

(ii) Calibration frequency;

(iii) Date of the last calibration;

(iv) Due date for next calibration;

(v) Name and signature of the person performing the calibration;

(vi) Traceability to master meter/prover used for calibration; and

(vii) Calibration report number.

Each meter shall be marked with the date of the last calibration and due date for the next calibration. All calibration meter recordings and logs/certificates shall be kept on file and made available upon request. All calibration records (including logs or certificates) shall be retained on file for a period of three years.

(3) API MPMS Chapter 12, Calculation of Petroleum Quantities. All calculations of net quantities shall be made in accordance with this chapter. Outside the U.S., use of tank shell correction factor is not required unless its use is a customary practice for custody transfer.

TABLE F1.09-2A CONVERSION FACTOR TABLE

Density @ 15°C Gallons @ 60°F to Liters @ 15°C, Multiply by Liters @ 15°C to Gallons @ 60°F, Multiply by

0.723 – 0.768 3.78286

0.264350

0.769 – 0.779

3.78309

0.264334

0.780 – 0.798

3.78334

0.264317

0.799 – 0.859

3.78356

0.264301

0.860 – 0.964

3.78381

0.264284

0.965 – 1.074 3.78405 0.264267

(d) SHIPPING DOCUMENTATION. The following information shall be mechanically annotated on the contractor’s shipping document (such as a truck’s metered ticket) when the document is used to determine quantity under this contract: gross and net quantity (gallons or liters, as required), observed and corrected API gravity/density, and the temperature (Fahrenheit or Celsius) at which the product was measured.. The following exceptions apply:

(1) Where government documents are the sole basis for payment, such as DD Form 250/250-1s, the information is not required.

(2) Where conveyances with temperature-compensating meters are used, the shipping document shall only be annotated with the corrected API gravity/density, the net quantity, and a statement that a temperature-compensating meter was used to determine net quantity.

(3) Where volume correction for temperature is not required in accordance with Paragraph (a)(1)(iii)(B) above, the shipping document shall be only be annotated with the API gravity (or density), gross quantity, and a statement that volume correction was not required.

(e) RIGHT TO REPRESENTATIVE. For f.o.b. origin deliveries, the Government has the right to have a representative present to witness the measurement of quantity. For f.o.b. destination deliveries, the Contractor has the right to have a representative present to witness the delivery and measurement of quantity.

(f) DISCREPANCIES. For f.o.b. destination deliveries utilizing volume corrected loading rack meter tickets to determine quantity:

(1) The quantities shown on the shipping document (volume corrected loading rack meter tickets) will be accepted as the quantity received, provided that any differences between that quantity and the Government’s receipt tank measurement at destination does not exceed one half of one percent (0.5%) of the amount on the shipping document.. If the difference is greater than one half of one percent (0.5%), the quantity determined by the Government using receipt tank measurements at destination will be used for acceptance and payment provided receipt tank measurements are identified in the Schedule as an approved quantity determination method for that line item. Quantity measurements using the methods specified in section (a)(1)(iii)(A) (1-3) above will be used for acceptance and payment regardless of any discrepancy with a loading rack meter ticket.

(2) If, the Government’s receipt tank quantity measurement varies by more than one half of one percent (0.5%) from the Contractor’s quantity measurement, the parties may conduct a joint investigation) of the variation in order to identify the cause of the discrepancy. Any quantity discrepancy that cannot be settled by the parties and results in a dispute shall be resolved under the Disputes provisions of the contract.

A-5

F-0003 / F1.11 DLA INTERNET BID BOARD SYSTEM (DIBBS) (DLA ENERGY) (APR 2014)

(a) Contractor Registration. Contractors must register in DIBBS to obtain a login account at https://www.dibbs.bsm.dla.mil. The login account will allow a contractor to register a primary and alternate email address for notifications. Contractors are strongly encouraged to establish a group email address for the primary email address for the contractor’s authorized point of contacts. The registered email addresses will be the only email used by the government to make notifications.

(b) All contractors must have an active System for Award Management (SAM) account, http://www.sam.gov in order to register for DIBBS.

(c) The Contractor shall use DIBBS to receive orders. DLA Energy will not be using DIBBS receipt of quotes capability. All quotations, proposals, bids shall be submitted in accordance with the terms and conditions of the solicitation.

(d) Preparation and Transmission of Orders

(1) The Government may issue an order for a specific delivery or a series of deliveries (e.g., several deliveries during a week).

The Government may also elect to issue an order covering a longer period (including monthly orders) and make periodic calls against these orders designating specific delivery dates, times, and quantities.

(2) Only a DLA Energy warranted Contracting Officer can issue an order, either orally or in writing, against a contract. An oral order issued by the warranted Contracting Officer shall provide the required advance notice to the Contractor and the following information: Interim order number; contract number; item number; ceiling price; quantity; delivery location; and the required delivery and/ or service date.

(i) For all product orders, the Contractor will receive an electronically signed written order via DIBBS, within 24 hours or one business day after the warranted Contracting Officer issues an oral order.

(ii) For all service orders, the Contractor will receive an electronically signed written order via DIBBS, within five business days after issuing the oral order.

(iii) Interim order number is subject to change once the electronically signed written order is received by the contractor. The order number on the written order will take precedence over the interim order number, if different.

(iv) Regardless of the unit price cited on the written order, the office designated to make payments on the written order will pay the applicable unit price in effect under the terms and conditions of the contract.

(v) Once the order has been issued, an email will be sent to the Contractor to provide notice that the order is available on the contract-specific web page. The order will also be submitted to the payment office.

(3) Calls against previously issued orders must be confirmed in writing within 24 hours or one business day via email message. The email confirmation will reference the previously issued order number and item number and designate specific delivery location, dates, and quantity to be delivered against that order.

(4) The Contractor’s nonreceipt of a written or electronic confirmation of an oral order or oral call against a written or electronic order does not relieve the Contractor from its obligation to perform in accordance with the oral order or oral call against a written or electronic order. The Contractor should contact the DLA Energy Contracting Officer if problems are experienced with receipt of the electronic or written confirmation.

SECTION G

CONTRTACT ADMINISTRATION DATA

FAR 52.232-40 - PROVIDING ACCELERATED PAYMENTS TO SMALL BUSINESS SUBCONTRACTORS

is incorporated by reference

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (MAY 2013)

(a) Definitions. As used in this clause— “Department of Defense Activity Address Code (DoDAAC)” is a six position code that uniquely identifies a unit, activity, or organization.

“Document type” means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

“Local processing office (LPO)” is the office responsible for payment certification when payment certification is done external to the entitlement system.

(b) Electronic invoicing. The WAWF system is the method to electronically process vendor payment requests and receiving reports, as authorized by DFARS 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall—

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.acquisition.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the “Web Based Training” link on the WAWF home page at https://wawf.eb.mil/ https://www.dibbs.bsm.dla.mil/ http://www.sam.gov/ http://www.acq.osd.mil/dpap/dars/dfars/html/current/252232.htm https://www.acquisition.gov/ https://wawf.eb.mil/ https://wawf.eb.mil/

A-6

(e) WAWF methods of document submission. Document submissions may be via web entry, Electronic Data Interchange, or File Transfer Protocol.

(f) WAWF payment instructions. The Contractor must use the following information when submitting payment requests and receiving reports in WAWF for this contract/order:

(1) Document type. The Contractor shall use the following document type(s).COMBO

(2) Inspection/acceptance location. The Contractor shall select the following inspection/acceptance location(s) in WAWF, as specified by the contracting officer. Destination

(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system.

Routing Data Table* Field Name in WAWF Data to be entered in WAWF Pay Official DoDAAC SL4701

Issue By DoDAAC SPE600 Admin DoDAAC SPE600

Inspect By DoDAAC SE5F01

Ship To Code SE5F01

Ship From Code NOT APPLICABLE Mark For Code NOT APPLICABLE

Service Approver (DoDAAC) NOT APPLICABLE

Service Acceptor (DoDAAC) SE5F01

Accept at Other DoDAAC SPE600 LPO DoDAAC NOT APPLICABLE

DCAA Auditor DoDAAC NOT APPLICABLE

Other DoDAAC(s) NOT APPLICABLE

(4) Payment request and supporting documentation. The Contractor shall ensure a payment request includes appropriate contract line item and subline item descriptions of the work performed or supplies delivered, unit price/cost per unit, fee (if applicable), and all relevant back-up documentation, as defined in DFARS Appendix F, (e.g. timesheets) in support of each payment request.

(5) WAWF email notifications. The Contractor shall enter the e-mail address identified below in the “Send Additional Email Notifications” field of WAWF once a document is submitted in the system.

Mark.Palombo@dla.mil

(g) WAWF point of contact.

(1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity’s WAWF point of contact. WAWF@dla.mil

(2) For technical WAWF help, contact the WAWF helpdesk at 866-618-5988.

SECTION M

EVALUATION FACTORS FOR AWARD

M-0001 / M55 CONVERSION FACTORS (DLA ENERGY MAR 2007)

(a) This provision applies to all products except lubricating oils.

(b) The offeror should use conversion factors that reflect its product characteristics and submit prices and transportation rates in the requested units. In the event prices or transportation rates are not submitted in the requested units, the following conversion factors based on an assumed density for the product will be used by DLA Energy in the evaluation of the offer.

(1) TABLE I.

One Imperial Gallon = 1.20095 U.S. Gallons at the same temperature One Liter = 0.264172 U.S. Gallons at the same temperature One Cubic Meter (1,000 liters) = 6.2898 Barrels at the same temperature One U.S. Barrel = 42 U.S. Gallons at the same temperature One Kilometer = 0.62137 Miles One Mile = 1.6093 Kilometers One Nautical Mile = 1.15 Statute Miles

A-7

(2) TABLE II.

DENSITY TYPICAL

PRODUCT @15oC @60oF

BARRELS PER GALLONS PER LITERS PER BARRELS PER GALLONS PER

Kg/m3 API METRIC TON METRIC TON METRIC TON LONG TON LONG TON

AUTOMOTIVE

GASOLINE (ALL) 744.9 58.4 8.462 355.42 1342.46 8.598 361.12

AVIATION

GASOLINE (ALL) 716.3 66.0 8.801 369.66 1396.06 8.943 375.59

BURNER FUEL OILS

FUEL OIL NO. 1 812.8 42.5 7.753 325.61 1230.31 7.877 330.83

FUEL OIL NO. 2 846.9 35.5 7.440 312.49 1180.78 7.560 317.51

FUEL OIL NO. 4 914.2 23.2 6.891 289.44 1093.85 7.002 294.09

FUEL OIL NO. 5

LIGHT 954.2 16.7 6.602 277.27 1048.00 6.707 281.71

FUEL OIL NO. 5

HEAVY 960.7 15.7 6.557 275.39 1040.91 6.662 279.81

FUEL OIL NO. 6 976.6 13.3 6.450 270.90 1023.96 6.554 275.25

DIESEL FUELS

NO. 1 DIESEL (ALL) 818.9 41.2 7.695 323.17 1122.15 7.818 328.36

NO. 2 DIESEL (ALL)

& GAS OIL 839.3 37.0 7.507 315.30 1191.47 7.628 320.36

INTERMEDIATE FUEL OILS

IFO 180 965.3 15.0 6.526 274.09 1035.95 6.630 278.48

IFO 380 973.9 13.7 6.468 271.65 1026.68 6.572 276.01

JET FUELS

JP4/JET B 764.6 53.5 8.243 346.22 1307.87 8.376 351.78

JP5 819.9 41.0 7.686 322.80 1219.66 7.809 327.98

JP8/JET A1/F34/TS1 805.9 44.0 7.820 328.42 1240.85 7.945 333.69

JET A 814.2 42.2 7.739 325.04 1228.20 7.863 330.26

KEROSINES (ALL) 815.2 42.0 7.730 324.68 1226.69 7.854 329.88

MARINE GAS OIL 839.3 37.0 7.507 315.30 1191.47 7.628 320.36

NAPHTHA 731.1 62.0 8.623 362.16 1367.80 8.761 367.97

NAVAL DISTILLATE

FUEL (F76) AND

DFW (F75) 844.3 36.0 7.463 313.43 1184.41 7.582 318.46

A-8

(3) TABLE III.

ASSUMED DENSITY

PRODUCT 20 deg C/20 deg C g/mL lb/gal Kg/gal

FSII DIEGME 1.025 8.561 3.884

(a) DEFINITION: As used in this contract provision: