Amendment_0002 1 .pdf

NSN 7540-01-152-8070 30-105 STANDARD FORM 30 (REV. 10-83)

PREVIOUS EDITION UNUSABLE Prescribed by GSA

FAR (48 CFR) 53.243

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

1. CONTRACT ID CODE PAGE 1 OF 8

PAGES

2. AMENDMENT/MODIFICATION NO.

3. EFFECTIVE DATE

12 June 2013

4. REQUISITION/PURCHASE REQ. NO.

N/A

5. PROJECT NO. (If applicable)

6. ISSUED BY CODE

DLA ENERGY - PEA

SP0600 7. ADMINISTERED BY (If other than Item 6)

CODE

8725 JOHN J. KINGMAN ROAD, SUITE 4950

FORT BELVOIR, VA 22060-6222

BUYER/SYMBOL - BRYAN SVEUM /DLA ENERGY PEA

PHONE - (703) 767-9556 P.P. 1.8R

8. NAME AND ADDRESS OF CONTRACTOR (NO., street, city, county, State, and ZIP Code)

X

9a. AMENDMENT OF SOLICITATION NO.

SP0600-13-R-0225

9b. DATED (SEE ITEM 11)

10 MAY 2013

10a. MODIFICATION OF CONTRACT/ORDER NO.

10b. DATED (SEE ITEM 13)

CODE FACILITY CODE

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

[X] The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers is [ ] extended, is not [ X ] extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods: (a) By completing Items 8 and 15, and returning _1_copy of the amendment;(b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS,

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b)

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor [ ] is not, [ X ] is required to sign this document and return _1_ copy to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

All offerors are required to acknowledge this amendment by completing Blocks 15A, 15B and 15C below. Return this document with your offer to DLA ENERGY-PEA, fax (703) 767-8506 or e-mail to bryan.sveum@dla.mil.

SEE CONTINUATION PAGES

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

16A. NAME OF CONTRACTING OFFICER

15B. NAME OF CONTRACTOR/OFFEROR

BY

(Signature of person authorized to sign)

15C. DATE

SIGNED

16B. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

16C. DATE SIGNED

mailto:bryan.sveum@dla.mi

AMENDMENT 0002

A. Pursuant to B-0001 B1.05-2 SUPPLIES TO BE FURNISHED, the following administrative corrections are made to the Ordering Office Numbers and should read as follows:

LOCATION LINE ITEM ORDERING NUMBER

AGANA HEIGHT 500-US 671-339-5056

AGANA HEIGHTS 504-US 671-344-9531

SUMAY 510-28 671-339-5056

SUMAY 515-28 671-339-5056

SUMAY 525-US 671-339-5056

SUMAY 530-US 671-339-5056

SUMAY 535-US 671-339-5056

B. Pursuant to B-0002 B19.01 ECONOMIC PRICE ADJUSTMENT-MARKET PRICE (PC&S)(KOREA/GUAM/JAPAN)(DLA ENERGY MAY2007), page 15, under paragraph (5) UPWARD CEILING ON ECONOMIC PRICE ADJUSTMENT is hereby revised to read as follows:

The Contractor agrees that the total increase in any contract unit price, pursuant to these economic price adjustment provisions, shall not exceed 375% percent of the base unit price in any applicable program year (whether a single year or a multiyear program), except as provided hereafter.

C. The following Provision FAR 52.216-18 ORDERING (OCT 1995), page 60, under paragraph (a) is hereby revised to read as follows:

Any supplies and services to be furnished under this contract shall be ordered by issuance of delivery orders or task orders by the individuals or activities designated in the Schedule. Such orders may be issued from 1 JUL 2013 through 30 JUN 2015.

D. The following are deleted from the solicitation:

1. C16.18 GASOLINE, AUTOMATIVE, LEADED OR UNLEADED (REGULAR/MIDGRADE/PREMUIUM) (DLA

ENERGY JUL 1998)

2. C16.26-12 FUEL OIL, DIESEL (AG2) (PC&S)(GUAM.TINIAN) (DLA ENERGY APR 2005)

E. The following Provision is hereby added to the Solicitation and/or OSP as applicable and included in full text:

C16.69 FUEL SPECIFICATIONS (PC&S) (DESC MAY 2007)

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent requirement will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below.

NOTE: Gasoline, gasohol and reformulated gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically throughout the United States. Therefore, Contractors are expected to know the local, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

(a) GASOLINE, AUTOMOTIVE, UNLEADED, GRADES REGULAR, MIDGRADE, AND PREMIUM.

Product shall conform to ASTM D 4814, as modified below.

(1) OCTANE REQUIREMENTS.

(i) Unleaded automotive gasoline shall meet the Anti-Knock Index (AKI) requirements shown in the table below.

DESC

PRODUCT

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE AKI,

MINIMUM

9130-00-148-7103 Gasoline, Regular Unleaded MUR 87 9130-01-272-0983 Gasoline, Midgrade Unleaded MUM 89 9130-00-148-7104 Gasoline, Premium Unleaded MUP 91

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(iii) For regular unleaded gasoline, in addition to an AKI of 87 minimum, the MON must not be less than 82.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

(3) See the SPECIFICATIONS (CONT'D) clause for additional regional gasoline requirements.

(b) GASOHOL, AUTOMOTIVE, UNLEADED, GRADES REGULAR, MIDGRADE, AND PREMIUM.

Products shall conform to Commercial Item Description (CID) A-A-52530 dated October 10, 1995, as modified below. In accordance with Executive Order 12261 of January 5, 1981, "Gasohol in Federal Motor Vehicles," Gasohol may be considered an acceptable substitute for Unleaded Gasoline. The Unleaded Gasoline items that permit the substitution of Gasohol are identified in the Schedule. Contractors are required to state, for each line item in their offer, whether Gasohol will be provided. Contractors will not be permitted to substitute Unleaded Gasoline under line items awarded as gasohol.

Also, Contractors are not permitted to substitute gasohol for gasoline under line items awarded as gasoline, except when Government regulations mandate use of fuel containing an oxygenate for control of carbon monoxide pollution.

(1) OCTANE REQUIREMENTS.

(i) Unleaded automotive gasohol shall meet the AKI requirements shown in the table below.

DESC

PRODUCT

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE AKI,

MINIMUM

9130-01-090-1093 Gasohol, Regular Unleaded GUR 87 9130-01-355-2393 Gasohol, Midgrade Unleaded GUM 89 9130-01-090-1094 Gasohol, Premium Unleaded GUP 91

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(iii) For regular unleaded gasohol, in addition to an AKI of 87 minimum, the MON must not be less than 82.

(2) OXYGENATE REQUIREMENTS.

(i) Ethanol concentration shall be between 9 and 11 volume percent.

(ii) Blending of ethanol into gasoline to make gasohol shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

(3) See the SPECIFICATIONS (CONT’D) clause for additional regional requirements affecting gasohol.

(c) REFORMULATED GASOLINE, AUTOMOTIVE, UNLEADED, GRADES REGULAR, MIDGRADE, AND PREMIUM. Product shall conform to ASTM D 4814 , as modified by the Environmental Protection Agency (EPA) requirements detailed in 40 CFR Part 80 - "Regulation of Fuels and Fuel Additives; Subpart D Reformulated Gasoline”. In part, these regulations mandate that Phase II complex model reformulated gasoline must meet three emissions performance requirements when compared to the baseline gasoline marketed by a refiner in 1990: a 27 percent reduction in emissions of volatile organic compounds (VOCs), a 22 percent reduction in emissions of toxic pollutants, and a 7 percent reduction in emissions of oxides of nitrogen (NOx). Further, Phase II complex model reformulated gasoline must meet two compositional requirements: 1.3 volume percent maximum benzene and no heavy metals (lead and manganese are examples of such metals).

(1) OCTANE REQUIREMENTS.

(i) Reformulated gasoline shall meet the AKI requirements shown in the table below.

DESC

PRODUCT

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE AKI,

MINIMUM

9130-01-388-4080 Reformulated Gasoline, Regular MRR 87 9130-01-388-4513 Reformulated Gasoline, Midgrade MMR 89 9130-01-388-4524 Reformulated Gasoline, Premium MPR 91

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, suppliers shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of permissible oxygenate into reformulated gasoline shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

(3) See the SPECIFICATIONS (CONT'D) clause for additional regional reformulated gasoline requirements.

(d) DIESEL FUEL.

(1) APPLICABLE TO ALL DIESEL GRADES.

(i) ADDITIVES.

(A) A fuel stabilizer additive conforming to MIL-S-53021 may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL- 53021.

(B) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity. Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(C) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(ii) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(iii) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by one of the following two properties: Cloud Point or Cold Filter Plugging Point.

(A) CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X4 of ASTM D 975.

(B) COLD FILTER PLUGGING POINT (CFPP). Unless a more restrictive CFPP limit is specified in the contract schedule, the maximum CFPP shall be 10 degrees Celsius below the tenth percentile minimum ambient temperature specified in Appendix X4 of ASTM D 975.

(iv) DYE. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

(2) APPLICABLE TO GRADES DS2, DS1, DSS, DSW, LS2, LS1, LSS, LSW, HS2 AND HS1 ONLY.

Product shall conform to commercial specification ASTM D 975. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown below.

ULTRA-LOW SULFUR GRADES

DESC MAXIMUM

PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED

DYE

9140-01-524-0139 Grade Number 2-D S15 (ULSD) DS2 0.0015 wt% No 9140-01-524-5174 Grade Number 1-D S15 (ULSD) DS1 0.0015 wt% No 9140-01-541-6760 Grade Number 2-D S15 (ULSD) DSS 0.0015 wt% Yes 9140-01-541-6767 Grade Number 1-D S15 (ULSD) DSW 0.0015 wt% Yes

LOW SULFUR GRADES

PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED

DYE

9140-01-398-0697 Grade Number 2-D S500 (“low sulfur No.2-D”) LS2 0.05 wt% No 9140-01-398-1130 Grade Number 1-D S500 (“low sulfur No.1-D”) LS1 0.05 wt% No 9140-01-413-4919 Grade Number 2-D S500 (“low sulfur No.2-D”) LSS 0.05 wt% Yes 9140-01-413-7494 Grade Number 1-D S500 (“low sulfur No.1-D”) LSW 0.05 wt% Yes

HIGH SULFUR GRADES

PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-01-398-1395 Grade Number 2-D S5000 (“regular No.2-D”) HS2 0.50 wt% Yes 9140-01-398-1422 Grade Number 1-D S5000 (“regular No.1-D”) HS1 0.50 wt% Yes

(3) APPLICABLE TO GRADES DLS, DLW, DF2, AND DF1 ONLY. Product shall conform to commercial specification ASTM D 975. In addition, product shall contain no more than 10 milligrams/liter (mg/L) of particulates as measured by ASTM D 6217. Product classification is shown below.

LOW SULFUR GRADES

PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-01-413-7511 Grade Number 2-D S500 (“low sulfur No.2-D”) DLS 0.05 wt% Yes 9140-01-412-1311 Grade Number 1-D S500 (“low sulfur No.1-D”) DLW 0.05 wt%

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-00-286-5294 Grade Number 2-D S5000 (“regular No.2-D”) DF2 0.50 wt%

9140-00-286-5286 Grade Number 1-D S5000 (“regular No.1-D”) DF1 0.50 wt% Yes

(4) APPLICABLE TO DIESEL GRADE NUMBER 1 ONLY. DESC frequently requires Number 1 diesel fuel grades when it is anticipated that the fuel may be exposed to temperatures below 10 degrees Fahrenheit (-12 degrees Celsius). These products shall conform to ASTM D 975 and additional requirements as specified above for each DESC product code. Although the Government does not encourage such actions, Contractors electing to deliver kerosene or Jet A to meet Number 1 diesel fuel requirements must—

(i) Provide certification to the Contracting Officer prior to 1 October of each year that the kerosene or Jet A will meet requirements applicable to the specific product code, including particularly, sulfur, dye, lubricity, viscosity and cetane index; AND

(ii) For each delivery, submit relevant documents (delivery tickets, bills of lading, etc.) indicating that Number 1 diesel fuel is being delivered.

(5) See the SPECIFICATIONS (CONT’D) clause for additional regional diesel requirements.

(e) FUEL OIL, BURNER (VIRGIN FUEL OILS). Applicable to all burner fuel oil grades. Product shall conform to ASTM D 396, as modified by the requirements of paragraphs (1) through (7) below. Product classification is shown in the table below. PRODUCT CONTAINING USED OIL SHALL NOT BE SUPPLIED. (See paragraph (f) below for DESC product codes, national stock numbers, and detailed requirements applicable to blends of residual fuel with recycled lubricating oil.)

DESC

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE PRODUCT CODE RED

DYE

9140-01-546-1786 Fuel Oil, Burner No. 2 S500 FL2 Yes 9140-00-247-4366 Fuel Oil, Burner No. 1 S5000 FS1 Yes 9140-00-247-4365 Fuel Oil, Burner No. 2 S5000 FS2 Yes 9140-01-107-6139 Fuel Oil, Burner No. 4 (Light) FL4 Yes 9140-00-247-4360 Fuel Oil, Burner No. 4 FS4 No 9140-01-058-4431 Fuel Oil, Burner No. 5 (Light) FL5 No 9140-00-247-4359 Fuel Oil, Burner No. 5 (Heavy) FS5 No 9140-00-247-4354 Fuel Oil, Burner No. 6 FS6 No

(1) These residual grades of burner fuel oil (Grades No. 4, No. 4(Light), No. 5(Light), No. 5(Heavy), and No. 6) shall consist of fossil-derived hydrocarbon stock. They may not contain used oil or other recycled petroleum components.

(2) SULFUR REQUIREMENT. Refer to the Schedule for the maximum allowable sulfur content of Burner Oil, Grades No. 4, No. 4(Light), No. 5(Light), No. 5(Heavy), and No. 6. The maximum allowable sulfur content for Burner Oil, Grades No. 1 S5000 and No. 2 S5000, shall be 0.50 weight percent or per State/local environmental requirements, whichever is more stringent. The maximum allowable sulfur content for Burner Oil, Grade No. 2 S500 shall be 0.05 weight percent.

(3) NITROGEN REQUIREMENT. The nitrogen content shall be tested using ASTM D 3228, Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method, or ASTM D 4629, Trace Nitrogen in Liquid Petroleum Hydrocarbons by Chemiluminescence Detection. The nitrogen content is used to determine nitrous oxide (NOx) emissions in boiler systems as determined by State/local environmental agencies. The requirement applies for line items with Burner Oil No. 4, Burner Oil No. 5 (heavy), Burner Oil No. 5 (light), and Burner Oil No. 6. The Contractor is required upon request from the Government to provide a copy of the test report, within two working days, that states the actual nitrogen content of fuel delivered.

(4) Blending of various compatible grades of burner oil to produce an intermediate grade is permitted, however, such blending shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the grade produced.

(5) The maximum allowable ash content for Burner Oil, Grade No. 6, shall be .50 weight percent using ASTM D 874, Standard Test Method for Sulfated Ash from Lubricating Oils and Additives.

(6) Under United States regulations, Grades No. 1, 2, and 4(Light) are required by 40 CFR Part 80 to contain a sufficient amount of the dye Solvent Red 164 so its presence is visually apparent. At or beyond terminal storage tanks, they are required by CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrally equivalent to 3.9 pounds per thousand barrels of the solid dye standard Solvent Red 26.

(7) APPLICABLE TO FUEL OIL, BURNER, GRADE #1 ONLY. This product shall conform to ASTM D

396. Contractors electing to deliver kerosene (red dye) to meet No. 1 burner oil requirements must—

(i) Provide certification to the Contracting Officer prior to 1 October of each year that the kerosene will meet No. 1 burner oil specifications, including , specifically, viscosity, distillation, density and pour point, AND

(ii) For each delivery, submit relevant documents (delivery tickets, bills of lading, etc.) indicating that No. 1 burner oil is being delivered.

(iii) All kerosene delivered to meet No. 1 burner oil must be tax free, i.e., dyed in accordance with IRS regulations.

(f) FUEL OIL, BURNER, CONTAINING RECYCLED USED OILS, GRADES 4, 5(LIGHT), 5(HEAVY) AND 6. Product shall conform to ASTM D 6823, as modified by the requirements of paragraphs (1) through (5) below.

Product classification is shown in the table below.

DESC

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE PRODUCT CODE

9140-01-468-9135 Fuel Oil, Burner, Grade RFC4 RF4 9140-01-468-9157 Fuel Oil, Burner, Grade RFC5L R5L 9140-01-468-9147 Fuel Oil, Burner, Grade RFC5H RF5 9140-01-468-9164 Fuel Oil, Burner, Grade RFC6 RF6

(1) SULFUR REQUIREMENT. Refer to the Schedule for the maximum allowable sulfur content of Grades 4, 5(Light), 5(Heavy), and 6.

(2) NITROGEN REQUIREMENT. The nitrogen content shall be tested using ASTM D 3228, Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method, or ASTM D 4629, Trace Nitrogen in Liquid Petroleum Hydrocarbons by Chemiluminescence Detection. The nitrogen content is used to determine nitrous oxide (NOx) emissions in boiler systems as determined by State/local environmental agencies. The Contractor is required upon request from the Government to provide a copy of the test report, within two working days, that states the actual nitrogen content of fuel delivered.

(3) INCLUSION OF OFF-SPECIFICATION USED OIL PROHIBITED. 40 CFR Parts 266 and 279 define off-specification used oil. The supply of RF4, R5L, RF5, or RF6 containing off-specification used oil is not permitted.

[ ] The offeror represents that it will provide certified test reports with associated QC documents validating compliance with EPA used oil standards contained in 40 CFR Parts 266 and 279 or State/local requirements, whichever is more stringent, for all contract deliveries under the line items identified above to—

ATTN: DESC-BPE ROOM 2954

DEFENSE ENERGY SUPPORT CENTER

8725 JOHN J KINGMAN ROAD SUITE 4950

FORT BELVOIR VA 22060-6222

Offeror's EPA Identification Number: _______________________

(4) Blending of various compatible grades of burner oil to produce an intermediate grade is permitted, however, such blending shall be accomplished by mechanical mixing or agitation in tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the contract.

(5) The maximum allowable ash content for Burner Oil, Grade RF6, shall be 0.50 mass percent, using ASTM D 874, Standard Test Method for Sulfated Ash from Lubricating Oils and Additives.

(g) KEROSENE. Product shall conform to ASTM D 3699. Classification of product is shown below.

LOW SULFUR GRADES

DESC MAXIMUM

9140-01-292-4460 Kerosene, Grade No. 1-K KS1 0.04 wt% max No 9140-01-461-3989 Kerosene, Grade No. 1-K KSR 0.04 wt% max Yes

PRODUCT SULFUR

9140-00-242-6748 Kerosene, Grade No. 2-K KSN 0.30 wt% max Yes

NOTE: The IRS requires taxation of No. 1-K and No. 2-K kerosene upon removal from the terminal unless the kerosene is indelibly (cannot be removed) dyed or used for military jet fuel. These requirements, part of 26 CFR 48 - Manufacturers and Retailers Excise Taxes, were published in the July 1, 1998, Federal Register. Only undyed (taxable) No. 1-K kerosene is suitable for use in nonflued (unvented) kerosene burner appliances. No. 2-K kerosene (dyed or undyed) is unsuitable for nonflued (unvented) kerosene burner appliances.

The color test requirement is deleted if red dye has been added in compliance with IRS regulations; however, the resulting fuel/dye blend must have a red tint.

(DESC 52.246-9FW5)