Plans 26230.pdf

PDF 7 MB Posted Jul 2, 2026

Attached to: 472/26230. MNB; Macomb C. F. - Units 4 & 5 Level IV Conversion
Solicitation number: RFQ 171 260000000378 1
Issued by: Michigan

About this file

Written by GovTribe AI · Jul 7, 2026

This is a construction plan document prepared by the State of Michigan Department of Technology, Management and Budget for the Department of Corrections at Macomb Correctional Facility (MAC) in New Haven, Michigan. The project involves a Level IV Conversion of Housing Units 4 and 5 (HU-4 and HU-5), with file number 472/26230.MNB and Matrix Project Number 260482.00. The scope of work includes architectural, mechanical, and electrical modifications to convert the facility to a higher security level. Key construction elements include the installation of new security surround walls with stainless steel posts and frames, new steel security doors with electromechanical locks, new stainless steel door frames with wire mesh, modification of existing fin tube heating enclosures, relocation of exhaust grilles, installation of new exit signage, door position monitoring systems, and fire protection modifications. The work requires coordination across multiple trades including general contracting, mechanical, electrical, and fire protection services. Contractors must comply with the 2023 Michigan Electrical Code, Michigan Mechanical Code, and NFPA standards, with particular attention to tamper-proof security requirements appropriate for a correctional facility. The plans specify that all electrical outages shall not exceed two hours, with portable generator backup required for longer shutdowns coordinated at least two weeks in advance.

The project requires adherence to strict facility security protocols and MDOC standards, including the use of security screws and tamper-resistant hardware in all inmate-accessible areas. Contractors must conduct a pre-bid site walk-through to verify existing conditions before bidding, as drawings are based on existing record documents and casual field observation with discrepancies to be reported to the engineer. The specifications include detailed requirements for door hardware, hinges, closers, thresholds, gaskets, and glazing, with specific manufacturer preferences noted (such as Hager, Pemko, and Willoughby for hardware components). All demolition work must be approved by the owner/tenant prior to commencement, and contractors are responsible for removing obsolete exposed conduit and equipment not scheduled for reuse. The project requires updated panel schedules for all affected electrical panels, arc flash labels for new panelboards, and new printed circuit directories. Post-construction meetings are mandated at six-month and eleven-month intervals during the warranty period to review and address any identified issues.

View the file

Other files

File	Type	Posted
LEIN Request 26230.pdf	PDF	Jul 2, 2026
Advertisement 26230.pdf	PDF	Jul 2, 2026
Service Disabled Veteran Owned Business Info Sheet 2025.pdf	PDF	Jul 2, 2026
MichSpec 26230.pdf	PDF	Jul 2, 2026

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

34625 26 MILE RD,

NEW HAVEN, MI 48048

FILE NUMBER: 472/26230.MNB

MATRIX PROJECT NUMBER: 260482.00MECHANICAL/ELECTRICAL ENGINEER

STATE OF MICHIGAN

DEPARTMENT OF TECHNOLOGY, MANAGEMENT AND BUDGET

FOR DEPARTMENT OF CORRECTIONS

MACOMB CORRECTIONAL FACILITY (MAC) - HU 4 & 5 LEVEL IV CONVERSION

N SITE MAP

DRAWING INDEX

HU-4

HU-5

A-000

TITLE SHEET

NJB

JFS

file no.

checked by drawn by consultant issue date funding code contract order no.

consultant job no.

260482.00

M a t r ix

472/26230.MNB

07/02/2026 BID SET

sheet description

A R

T O

C H

N O

Y , M

A N

A G

T A

N D

B U

D G

O F

A N

A D

A M

P . L

A C

H , R

A , D

A C

A D

O N

A N

D C

O N

U C

N D

M a t r ix

A-101

CLARKSTON, MI

7300 DIXIE HWY.

PHONE

FAX

PHONE

248.605.2030 248.605.2030

48346 #600

WEB DSARCHITECTS.COM

ARCHITECTS

F M

N D

O F

H N

G Y

, M A

N A

A N

D B

U D

A D

A M

P . L

A C

H , R

A , D

A C

A D

O N

A N

D C

O N

U C

N D

AutoCAD SHX Text %%uFLOOR PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

HOUSING UNIT 4&5 - ACTIVITY ROOM

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

%%UDEMOLITION PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER A

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER B

AutoCAD SHX Text

DEMOLITION NOTES

AutoCAD SHX Text

DEMOLITION NOTES

AutoCAD SHX Text

CONSTRUCTION NOTES

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND DISPOSE OF A PORTION OF EXISTING BRICK VENEER, CMU BLOCK WALL AND INSULATION FOR FUTURE DOOR AND LINTELS. PROVIDE NEW TEMPORARY SHORING AS REQUIRED.

AutoCAD SHX Text

REFER TO MECHANICAL DRAWINGS FOR HEATER WORK.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND RELOCATE WALL MOUNTED BULLETIN CASES, VERIFY WITH OWNER EXACT LOCATIONS OF REINSTALL.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND DISPOSE OF INDICATED EXISTING STAINLESS STEEL TABLE FOR HOUSING UNIT #4 ONLY.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW 8" SINGLE COURSE MASONRY LINTEL WITH (2) #5 BARS ABOVE DOOR OPENING AND 8" BEARING EACH END. GROUT CORES SOLID BELOW BEARING EACH END. PROVIDE NEW L4" X 4" X 3/8" STEEL ANGLE BRICK LINTEL ABOVE DOOR OPENING.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW BRICK WEEPS HOLES TO MATCH EXISTING ABOVE DOOR OPENING WITH NEW METAL FLASHING AND DRAINAGE MATERIAL ABOVE DOOR OPENING.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW 8" BULLNOSE CMU END BLOCKS AND TOOTH INTO EXISTING. PROVIDE NEW PAINT FINISH TO MATCH EXISTING ON NEW CMU AS RESULT OF NEW DOOR INSTALLATION.

AutoCAD SHX Text

401 - HU#4

AutoCAD SHX Text PROVIDE NEW VCT FLOORING FINISH TO MATCH EXISTING IN DOOR OPENING AS RESULT OF DEMOLITION AND NEW DOOR INSTALLATION.

AutoCAD SHX Text file no.

AutoCAD SHX Text checked by

AutoCAD SHX Text drawn by

AutoCAD SHX Text consultant

AutoCAD SHX Text issue date

AutoCAD SHX Text index no.

AutoCAD SHX Text contract order no.

AutoCAD SHX Text consultant job no.

AutoCAD SHX Text 24233.00

AutoCAD SHX Text sheet title

AutoCAD SHX Text

CONSULTING ENGINEERS, INC

AutoCAD SHX Text

FAX: 517.487.2544

AutoCAD SHX Text

PHONE: 517.487.2511

AutoCAD SHX Text

LANSING, MI 48917

AutoCAD SHX Text

544 CHERBOURG DRIVE

AutoCAD SHX Text

MATRIX PROJECT:

AutoCAD SHX Text WEB: www.matrixceinc.com

AutoCAD SHX Text

MACOMB CORRECTIONAL FACILITY

AutoCAD SHX Text

NEW HAVEN, MICHIGAN

AutoCAD SHX Text 24233.00

AutoCAD SHX Text

472/24052.JGH

AutoCAD SHX Text

SHEET NUMBER

AutoCAD SHX Text

STATEWIDE PERIMETER

AutoCAD SHX Text

REPAIR/ REPLACEMENT

AutoCAD SHX Text

KJM

AutoCAD SHX Text

DJS

AutoCAD SHX Text

HOUSING UNIT #4&#5 PLANS

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

501 - HU#5

AutoCAD SHX Text %%uFLOOR PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER A

AutoCAD SHX Text

NORTH

AutoCAD SHX Text %%uFLOOR PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER B

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

CONSTRUCTION NOTES

AutoCAD SHX Text

CONSTRUCTION NOTES

AutoCAD SHX Text PROVIDE AND INSTALL NEW SECURITY SURROUND WALL, STEEL POSTS, METAL DOOR FRAME, CUFF SLOTS AND SLAM LOCKS AS REQUIRED. REFER TO DETAILS NO. 2 AND NO. 3 ON SHEET A-501 FOR MORE INFORMATION.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW METAL DIVIDER FRAME. SEE DETAIL NO. 4 ON SHEET A-501 FOR MORE INFORMATION.

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UTYP.

AutoCAD SHX Text

%%UBELOW

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UTYP.

AutoCAD SHX Text

%%UABOVE

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UBELOW

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UABOVE

AutoCAD SHX Text

%%UREFLECTED CEILING PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER A

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

HOUSING UNIT 4&5 - SHOWER B

AutoCAD SHX Text

REFLECTED CEILING NOTES

AutoCAD SHX Text

REFLECTED CEILING NOTES

AutoCAD SHX Text

%%UDEMOLITION PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

%%UREFLECTED CEILING PLAN

AutoCAD SHX Text 1/2" = 1'-0"

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

AutoCAD SHX Text SHADED AREA INDICATES TO REMOVE AND DISPOSE OF EXISTING PORTION OF GYPSUM BOARD CEILING TO ALLOW INSTALLATION OF NEW STEEL POSTS TO BOTTOM OF EXISTING CONCRETE DECK ABOVE.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND DISPOSE OF DAMAGED WALL TILES AFTER SECURITY DOOR AND FRAME BRACKET REMOVAL, APPROX. (6) BRACKETS PER SHOWER.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND SALVAGE OF EXISTING EXHAUST GRILLE AND TEMPORARY MOVE EXHAUST VENTING AS NEEDED FOR CLEARANCE TO INSTALL STEEL POSTS.

AutoCAD SHX Text

EXISTING TILED CURVED SHOWER TRANSITION FLOOR TO REMAIN.

AutoCAD SHX Text

EXISTING FLOOR DRAINS TO REMAIN, TYP.

AutoCAD SHX Text

EXISTING WALL MOUNTED HVAC HEATER TO REMAIN.

AutoCAD SHX Text

AutoCAD SHX Text NEW 3" X 3" X 3/16" STAINLESS STEEL POST. REFER TO DETAIL NO. 5 AND NO. 6 ON SHEET A-501 FOR POST BASE CONNECTION AND POST CAP CONNECTION, TYP.

AutoCAD SHX Text

AutoCAD SHX Text NEW 6" X 3" X 3/16" STAINLESS STEEL POST. REFER TO DETAIL NO. 7 AND NO. 8 ON SHEET A-501 FOR POST BASE CONNECTION AND POST CAP CONNECTION, TYP.

AutoCAD SHX Text PROVIDE NEW CONCRETE INFILL AT EXISTING BRICK LEDGE, TOP OF NEW CONCRETE INFILL TO ALIGN WITH TOP OF ADJACENT CONCRETE SLAB AND PROVIDE A PROPER AND PLUM SURFACE FOR NEW DOOR THRESHOLD.

AutoCAD SHX Text SHADED AREA INDICATES TO PROVIDE NEW MOLD RESISTANT GYPSUM BOARD CEILING TO MATCH EXISTING THICKNESS AS RESULT OF DEMOLITION OF EXISTING TO INSTALL POST, TYP.

AutoCAD SHX Text

REINSTALL EXHAUST GRILLE AND REATTACH EXISTING EXHAUST VENTILATION.

AutoCAD SHX Text

EXISTING LIGHT FIXTURE TO REMAIN.

AutoCAD SHX Text

EXISTING SPRINKLER HEAD TO REMAIN.

AutoCAD SHX Text

EXISTING CEILING ACCESS HATCH TO REMAIN.

AutoCAD SHX Text

PROVIDE NEW TAMPER RESISTANT CAULK AROUND PERIMETER OF POST.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND DISPOSE OF EXISTING STEEL SECURITY DOOR, FRAME AND HARDWARE IN HOUSING UNIT #5 ONLY, NO SECURITY DOORS IN HOUSING UNIT #4.

AutoCAD SHX Text

AutoCAD SHX Text SHADED AREA INDICATES TO REMOVE AND DISPOSE OF EXISTING PORTION OF GYPSUM BOARD CEILING TO ALLOW INSTALLATION OF NEW STEEL POSTS TO BOTTOM OF EXISTING CONCRETE DECK ABOVE.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND DISPOSE OF DAMAGED WALL TILES AFTER SECURITY DOOR AND FRAME BRACKET REMOVAL, APPROX. (6) BRACKETS PER SHOWER.

AutoCAD SHX Text

AutoCAD SHX Text REMOVE AND SALVAGE OF EXISTING EXHAUST GRILLE AND TEMPORARY MOVE EXHAUST VENTING AS NEEDED FOR CLEARANCE TO INSTALL STEEL POSTS.

AutoCAD SHX Text

EXISTING TILED CURVED SHOWER TRANSITION FLOOR TO REMAIN.

AutoCAD SHX Text

EXISTING FLOOR DRAINS TO REMAIN, TYP.

AutoCAD SHX Text

EXISTING WALL MOUNTED HVAC HEATER TO REMAIN.

AutoCAD SHX Text

EXISTING CLOTHES HOOKS TO REMAIN, TYP.

AutoCAD SHX Text REMOVE AND DISPOSE OF EXISTING STEEL SECURITY DOOR, FRAME AND HARDWARE IN HOUSING UNIT #5 ONLY, NO SECURITY DOORS IN HOUSING UNIT #4.

AutoCAD SHX Text

AutoCAD SHX Text INSTALL FACILITY PROVIDED WALL TILE TO MATCH EXISTING AS RESULT OF HOLES FROM THE SECURITY DOORS BRACKETS IN HOUSING UNIT #5 ONLY. PROVIDE NEW GROUT TO MATCH EXISTING.

AutoCAD SHX Text

REMOVE AND DISPOSE OF INDICATED CLOTHES HOOKS ONLY.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW METAL DIVIDER FRAME. SEE DETAIL NO. 4 ON SHEET A-501 FOR MORE INFORMATION.

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UTYP.

AutoCAD SHX Text

%%UBELOW

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UTYP.

AutoCAD SHX Text

%%UABOVE

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UBELOW

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%UABOVE

AutoCAD SHX Text

AutoCAD SHX Text NEW 3" X 3" X 3/16" STAINLESS STEEL POST. REFER TO DETAIL NO. 5 AND NO. 6 ON SHEET A-501 FOR POST BASE CONNECTION AND POST CAP CONNECTION, TYP.

AutoCAD SHX Text

AutoCAD SHX Text NEW 6" X 3" X 3/16" STAINLESS STEEL POST. REFER TO DETAIL NO. 7 AND NO. 8 ON SHEET A-501 FOR POST BASE CONNECTION AND POST CAP CONNECTION, TYP.

AutoCAD SHX Text

PROVIDE NEW TAMPER RESISTANT CAULK AROUND PERIMETER OF POST.

AutoCAD SHX Text

AutoCAD SHX Text SHADED AREA INDICATES TO PROVIDE NEW MOLD RESISTANT GYPSUM BOARD CEILING TO MATCH EXISTING THICKNESS AS RESULT OF DEMOLITION OF EXISTING TO INSTALL POST, TYP.

AutoCAD SHX Text

REINSTALL EXHAUST GRILLE AND REATTACH EXISTING EXHAUST VENTILATION.

AutoCAD SHX Text

EXISTING LIGHT FIXTURE TO REMAIN.

AutoCAD SHX Text

EXISTING SPRINKLER HEAD TO REMAIN.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW PAINT FINISH TO MATCH EXISTING ACROSS THE ENTIRE CEILING IN SHOWER A.

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE NEW PAINT FINISH TO MATCH EXISTING ACROSS THE ENTIRE CEILING IN SHOWER B.

AutoCAD SHX Text

INDICATED EXISTING CLOTHES HOOKS TO REMAIN.

AutoCAD SHX Text

AutoCAD SHX Text EXISTING METAL PLATE TO REMAIN IN HOUSING UNIT #5B AND IS ONLY LOCATED IN HOUSING UNIT #5B.

AutoCAD SHX Text

AutoCAD SHX Text P

AutoCAD SHX Text L

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text B

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text U

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text M

AutoCAD SHX Text S

AutoCAD SHX Text P

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text Q

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text P

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text S

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text INSTALL FACILITY PROVIDED WALL TILE TO MATCH EXISTING AS RESULT OF HOLES FROM THE SECURITY DOORS BRACKETS IN HOUSING UNIT #5 ONLY. PROVIDE NEW GROUT TO MATCH EXISTING.

AutoCAD SHX Text

BID 7-2-267-2-26

AutoCAD SHX Text

DOOR CONTROL SHALL BE TIED INTO LOCAL CONTROL CENTER IN HOUSING UNIT 4 OR 5.

AutoCAD SHX Text

AutoCAD SHX Text NEW DOOR POSITION ALARM SENSOR SHALL BE TIED INTO LOCAL CONTROL CENTER IN HOUSING UNIT 4 OR 5 AND BACK TO CONTROL CENTER IN ADMINISTRATION BUILDING.

AutoCAD SHX Text

M a t r ix

F M

A-501

CLARKSTON, MI

7300 DIXIE HWY.

PHONE

FAX

PHONE

248.605.2030 248.605.2030

48346 #600

WEB DSARCHITECTS.COM

ARCHITECTS

A R

T O

C H

N O

Y , M

A N

A G

T A

N D

B U

D G

A D

A M

P . L

A C

H , R

A , D

A C

A D

O N

A N

D C

O N

U C

N D

AutoCAD SHX Text C1

AutoCAD SHX Text PARALLEL CLOSER - PUSH SIDE - NO HOLD OPEN PROVIDE NEW 'LCN' CLOSER #4210 SERIES. PARALLEL (PUSH SIDE) MOUNTING. FINISH 689 ALUMINUM. PROVIDE 4210-3077EDA, EXTRA HEAVY DUTY ARM.

AutoCAD SHX Text H1

AutoCAD SHX Text BALL BEARING- NON REMOVABLE PIN PROVIDE NEW HINGES, 2 PAIR PER LEAF, 4 1/2" X 4 1/2", WITH BALL BALL BALL BEARINGS, NON-REMOVABLE PIN, BB1199 BY 'HAGER' OR EQUAL. FINISH US32D.

AutoCAD SHX Text F1

AutoCAD SHX Text ALUM THRESHOLD PROVIDE NEW HEAVY DUTY LATCHING PANIC EXIT SADDLE THRESHOLD BY 'PEMKO' 1700 SERIES OR EQUAL. FINISH 'A'. VERIFY IN FIELD EXACT WIDTH, LENGTH AND MATCH DEPTH OF FRAME.

AutoCAD SHX Text

GS1

AutoCAD SHX Text WEATHERSTRIP THERMAL SEAL - NOT FIRE RATED PROVIDE NEW FIRE RATED ADHESIVE GASKETING FOR FIRE AND SMOKE BY 'PEMKO' MODEL #PK33_ OR EQUAL. FINISH 'BL' BLACK.

AutoCAD SHX Text

DOOR

AutoCAD SHX Text

HINGES

AutoCAD SHX Text

CLOSERS

AutoCAD SHX Text

THRESHOLD

AutoCAD SHX Text

GASKETS AND SEALS

AutoCAD SHX Text

DOOR SCHEDULE

AutoCAD SHX Text

DOOR

AutoCAD SHX Text

NO.

AutoCAD SHX Text

OPEN. SIZE

AutoCAD SHX Text

DOOR

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

DOOR

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

FRAME

AutoCAD SHX Text

CLOSER

AutoCAD SHX Text

FRAME

AutoCAD SHX Text

LATCH

AutoCAD SHX Text

HINGES

AutoCAD SHX Text G1.

AutoCAD SHX Text ALL DOOR SIZE DIMENSIONS GIVEN ARE APPROXIMATE. DOOR SUPPLIER SHALL FIELD VERIFY EXACT REQUIREMENTS.

AutoCAD SHX Text

FRAME

AutoCAD SHX Text T1

AutoCAD SHX Text

THRESHOLD

AutoCAD SHX Text

GASKETS

AutoCAD SHX Text

GENERAL NOTES

AutoCAD SHX Text

GLAZING

AutoCAD SHX Text

GL1.

AutoCAD SHX Text EXTERIOR - INSIDE SECURED AREA - 1 1/4" PATRIOT ARMOR LOW-E INSULATED GLAZING WITH U-VALUE OF 0.25 (R-4).

AutoCAD SHX Text

GLAZING

AutoCAD SHX Text D1

AutoCAD SHX Text F1

AutoCAD SHX Text

LS1

AutoCAD SHX Text H1

AutoCAD SHX Text STEEL FRAME - 10 GA PROVIDE NEW 'AMERICAN STEEL PRODUCTS' DOOR FRAME. FRAME TO BE AN, 10 GAUGE GALVANNEALED DOUBLE RABBET WITH WELDED CORNERS. PROVIDE FRAME BACK COATING AND GROUT FRAME SOLID. PRIME FINISH. FIELD PAINT TO MATCH EXISTING. PROVIDE 4" HEADER AND 2" JAMBS.

AutoCAD SHX Text C1

AutoCAD SHX Text T1

AutoCAD SHX Text

GS1

AutoCAD SHX Text

LS1

AutoCAD SHX Text

LOCKSET

AutoCAD SHX Text 3'-0" X 7'-0"

AutoCAD SHX Text

STEEL

AutoCAD SHX Text

STEEL

AutoCAD SHX Text

GL1

AutoCAD SHX Text

AutoCAD SHX Text D1

AutoCAD SHX Text F1

AutoCAD SHX Text

LS1

AutoCAD SHX Text H1

AutoCAD SHX Text C1

AutoCAD SHX Text T1

AutoCAD SHX Text

GS1

AutoCAD SHX Text 3'-0" X 7'-0"

AutoCAD SHX Text

STEEL

AutoCAD SHX Text

STEEL

AutoCAD SHX Text

GL1

AutoCAD SHX Text STEEL - INSULATED - HALF LITE PROVIDE NEW 'CECO' RESTRICTDOR SERIES STEEL STIFFENED DOOR WITH FIBERGLASS INSULATION. EXTERIOR TO BE 14 GAUGE GALVANNEALED STEEL WITH SEAMLESS WELDED EDGE CONSTRUCTION LEVEL 4. PROVIDE LOW PROFILE LITE KIT L-FRA100-SP GALVANNEAL - A40 STEEL BY 'NATIONAL GUARD PRODUCTS, INC.' LITE TO BE 2'-11 1/2"H X 2'-0 1/2"W CENTERED IN DOOR ABOVE EXIT DEVICE. PROVIDE TORX SECURITY SCREWS. PRIME FINISH. FIELD PAINT TO MATCH EXISTING.

AutoCAD SHX Text D1

AutoCAD SHX Text ELECTRICAL - DEADLATCH - KEYED BOTH SIDES PROVIDE NEW ELECTROMECHANICAL LOCK BY 'WILLOUGHBY LOCKING SYSTEMS' WLS-1300, MOTORIZED, DEADLOCKING, LATCH, WITH KEY CYLINDER, SOLENOID, KEYED BOTH SIDES. STAINLESS STEEL FINISH. DOOR CONTROL SHALL BE TIED INTO LOCAL CONTROL CENTER IN HOUSING UNIT 4 OR 5.

AutoCAD SHX Text

HA1

AutoCAD SHX Text HORIZONTAL TUBE PULL PROVIDE NEW STAINLESS STEEL HORIZONTAL TUBE PULL BY 'HAGER' MODEL #136S OR EQUAL. 1-1/4" PULL DIAMETER. FINISH US32D.

AutoCAD SHX Text

HA2

AutoCAD SHX Text VERTICAL TUBE PULL PROVIDE NEW 18" STAINLESS STEEL VERTICAL TUBE PULL BY 'HAGER' MODEL #10 OR EQUAL. 1-1/4" PULL DIAMETER. FINISH US32D.

AutoCAD SHX Text

HANDLES

AutoCAD SHX Text

HANDLES

AutoCAD SHX Text

HA1,2

AutoCAD SHX Text

HA1,2

AutoCAD SHX Text PROTECTION PLATE - 33" - 36" +/- PROVIDE NEW STAINLESS STEEL HEAVY DUTY KICK PLATE BY 'ROCKWOOD' MODEL #K1062 OR EQUAL. 0.0.62 THICKNESS. FINISH US32D. FASTEN WITH 'TORX' SECURITY TORX SCREWS. PLATE TO BE 33" TO 36" HIGH X 33" TO 36" WIDE.

AutoCAD SHX Text

KICK PLATE

AutoCAD SHX Text K1

AutoCAD SHX Text

KICK PLATE

AutoCAD SHX Text K1

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3/4" = 1'-0"

AutoCAD SHX Text

WALL SECTION AT DOOR OPENING

AutoCAD SHX Text

EXISTING CONCRETE FOOTING TO REMAIN

AutoCAD SHX Text

TOP OF NEW CONCRETE INFILL AND EXISTING SLAB ON GRADE

AutoCAD SHX Text 100'-0"

AutoCAD SHX Text

TOP OF NEW DOOR ROUGH OPENING

AutoCAD SHX Text 107'-4"

AutoCAD SHX Text

NEW STEEL DOOR AND STEEL DOOR FRAME, REFER TO DOOR SCHEDULE FOR MORE INFORMATION

AutoCAD SHX Text NEW SINGLE COURSE 8" MASONRY LINTEL WITH (2) #5 BARS WITH 8" BEARING ON EACH END AND GROUT SOLID CORES BELOW BEARING ENDS

AutoCAD SHX Text

NEW 4" X 4" X 3/8" L STEEL ANGLE BRICK LINTEL

AutoCAD SHX Text

NEW METAL FLASHING WITH DRAINAGE MATERIAL

AutoCAD SHX Text

NEW WEEPS TO MATCH EXISTING

AutoCAD SHX Text NEW PAINT FINISH TO MATCH EXISTING ON EXISTING CMU AS RESULT OF NEW DOOR INSTALLATION

AutoCAD SHX Text

NEW VCT FLOORING FINISH TO MATCH EXISTING AS RESULT OF NEW DOOR INSTALLATION

AutoCAD SHX Text NEW CONCRETE INFILL AT EXISTING BRICK LEDGE, ALIGN NEW INFILL WITH TOP OF ADJACENT EXISTING SLAB ON GRADE

AutoCAD SHX Text

EXISTING SLAB ON GRADE

AutoCAD SHX Text file no.

AutoCAD SHX Text checked by

AutoCAD SHX Text drawn by

AutoCAD SHX Text consultant

AutoCAD SHX Text issue date

AutoCAD SHX Text index no.

AutoCAD SHX Text contract order no.

AutoCAD SHX Text consultant job no.

AutoCAD SHX Text 24233.00

AutoCAD SHX Text sheet title

AutoCAD SHX Text

CONSULTING ENGINEERS, INC

AutoCAD SHX Text

FAX: 517.487.2544

AutoCAD SHX Text

PHONE: 517.487.2511

AutoCAD SHX Text

LANSING, MI 48917

AutoCAD SHX Text

544 CHERBOURG DRIVE

AutoCAD SHX Text

MATRIX PROJECT:

AutoCAD SHX Text WEB: www.matrixceinc.com

AutoCAD SHX Text

MACOMB CORRECTIONAL FACILITY

AutoCAD SHX Text

NEW HAVEN, MICHIGAN

AutoCAD SHX Text 24233.00

AutoCAD SHX Text

472/24052.JGH

AutoCAD SHX Text

SHEET NUMBER

AutoCAD SHX Text

STATEWIDE PERIMETER

AutoCAD SHX Text

REPAIR/ REPLACEMENT

AutoCAD SHX Text

KJM

AutoCAD SHX Text

DJS

AutoCAD SHX Text

DETAILS

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3/4" = 1'-0"

AutoCAD SHX Text

DOOR ELEVATION

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 1 1/2" = 1'-0"

AutoCAD SHX Text

DOOR SECTION

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3/4" = 1'-0"

AutoCAD SHX Text

DIVIDER ELEVATION

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3" = 1'-0"

AutoCAD SHX Text

3" POST BASE CONNECTION

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3" = 1'-0"

AutoCAD SHX Text

3" POST CAP CONNECTION

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

%%USIM.

AutoCAD SHX Text

%%USIM.

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

AutoCAD SHX Text A-501

AutoCAD SHX Text

EXISTING TILE FLOOR

AutoCAD SHX Text NEW 3"X3"X3/16" STAINLESS STEEL POST WITH 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY

AutoCAD SHX Text NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER WITH 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, NEW DOOR IS 2'-8" X 6'-6" OVERALL. NEW HINGES, 2 PAIR PER LEAF, 4 1/2" X 4 1/2", WITH NEW HINGES, 2 PAIR PER LEAF, 4 1/2" X 4 1/2", WITH BALL BEARINGS, NON-REMOVABLE PIN, BB1199 BY 'HAGER' OR EQUAL. FINISH US32D. PROVIDE 15"X4 1/2" CUFF SLOT IN DOOR. PROVIDE NEW SURFACE MOUNTED SLAM LOCK AND SURFACE MOUNTED STRIKE BY 'WILLOUGHBY' OR EQUAL. INSURE THAT MECHANISM HAS LOCKING LATCH POSITION IN A WAY TO CLOSE SHUT BY SLAMMING. PROVIDE 4"X2"X3/16" STAINLESS STEEL FRAME FOR SLAM LOCK TO MOUNT TO AND SUPPORT CUFF SLOT FRAME.

AutoCAD SHX Text NEW 6"X3"X3/16" STAINLESS STEEL POST WITH 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY

AutoCAD SHX Text NEW 3"X3"X3/16" STAINLESS STEEL HEADER WITH 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY. FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL HEADER, FIELD WELDED TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text PROVIDE NEW MOLD RESISTANT GYPSUM BOARD CEILING AS DEMOLITION FOR NEW POST INSTALLATION, THICKNESS TO MATCH EXISTING, PROVIDE NEW PAINT FINISH ACROSS ENTIRE SHOWER CEILING TO MATCH EXISTING

AutoCAD SHX Text

EXISTING DECKING ABOVE

AutoCAD SHX Text EXISTING WALL TILE TO REMAIN AND INSTALL NEW WALL TILES IN HOUSING UNIT #5 AS RESULT OF DEMOLITION

AutoCAD SHX Text

EXISTING TILE FLOOR

AutoCAD SHX Text

NEW 6"X3"X3/16" STAINLESS STEEL POST AT CENTER OF SURROUND WALL

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL HEADER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text PROVIDE NEW MOLD RESISTANT GYPSUM BOARD CEILING AS DEMOLITION FOR NEW POST INSTALLATION, THICKNESS TO MATCH EXISTING, PROVIDE NEW PAINT FINISH TO MATCH EXISTING

AutoCAD SHX Text

EXISTING DECKING ABOVE

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text

EXISTING TILE FLOOR

AutoCAD SHX Text NEW MOLD RESISTANT GYPSUM BOARD CEILING AS DEMOLITION FOR NEW POST INSTALLATION, THICKNESS TO MATCH EXISTING, PROVIDE NEW PAINT FINISH TO MATCH EXISTING

AutoCAD SHX Text

EXISTING DECKING ABOVE

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIP ANGLE WITH NEW 1/4" DIA. TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL STIFFENER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL STIFFENER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL STIFFENER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 6"X3"X3/16" STAINLESS STEEL POST AT CENTER OF SURROUND WALL

AutoCAD SHX Text

REFER TO DETAIL NO. 2 AND NO. 3 FOR DOOR CONSTRUCTION, TYP.

AutoCAD SHX Text

EXISTING WALL TILE TO REMAIN, TYP.

AutoCAD SHX Text

EXISTING WALL TILE TO REMAIN, TYP.

AutoCAD SHX Text

EXISTING WALL TILE TO REMAIN, TYP.

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIPANGLE WITH NEW 1/4" DIA. STAINLESS STEEL TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text NEW 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL POST

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIPANGLE WITH NEW 1/4" DIA. STAINLESS STEEL TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL HEADER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text

NEW TAMPER RESISTANT CAULK ALONG PERIMETER OF POST BASE, TYP.

AutoCAD SHX Text

NEW TAMPER RESISTANT CAULK ALONG PERIMETER OF POST BASE, TYP.

AutoCAD SHX Text

NEW TAMPER RESISTANT CAULK ALONG PERIMETER OF POST BASE, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOOR FRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text

NEW CUFF SLOT

AutoCAD SHX Text

NEW 6"X3"X3/16" STAINLESS STEEL POST AT CENTER OF SURROUND WALL

AutoCAD SHX Text NEW 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3" = 1'-0"

AutoCAD SHX Text

6" POST BASE CONNECTION

AutoCAD SHX Text A-101

AutoCAD SHX Text

AutoCAD SHX Text 3" = 1'-0"

AutoCAD SHX Text

6" POST CAP CONNECTION

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIPANGLE WITH NEW 1/4" DIA. STAINLESS STEEL TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 2"X2"X3/16" STAINLESS STEEL DOORFRAME WELDED TOGETHER, TYP.

AutoCAD SHX Text NEW 3/4"X5/8" CONT. STAINLESS STEEL DOOR STOP ALONG PERIMETER OF DOOR OPENING ONLY

AutoCAD SHX Text

NEW 6"X3"X3/16" STAINLESS STEEL POST

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIP ANGLE WITH NEW 1/4" DIA. STAINLESS STEEL TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text

NEW TAMPER RESISTANT CAULK ALONG PERIMETER OF POST BASE, TYP.

AutoCAD SHX Text

NEW DOOR HINGE

AutoCAD SHX Text

NEW 2"X2"X1/4" STAINLESS STEEL WIRE MESH WITH WOVEN LOCK CRIMP WEAVE, TYP.

AutoCAD SHX Text

NEW 6"X3"X3/16" STAINLESS STEEL POST

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL HEADER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text REPLACE CUT CMU BLOCK WITH NEW 8" BULLNOSE EDGE CMU BLOCK AND TOOTH INTO EXISTING AROUND NEW ROUGH OPENING AND GROUT SOLID AS RESULT OF CMU LINTEL BEARING ABOVE, PAINT NEW BLOCK TO MATCH EXISTING

AutoCAD SHX Text

NEW 3"X3"X3/16" STAINLESS STEEL HEADER, FIELD WELD TO VERTICAL 3" AND 6" POST

AutoCAD SHX Text NEW 2"X2"X3/16"X2" LONG STAINLESS STEEL CLIP ANGLE WITH NEW 1/4" DIA. TAMPER RESISTANT THRU BOLTS, NUTS, AND WASHERS, TYP.

AutoCAD SHX Text A1.

AutoCAD SHX Text ELECT - DOOR POSITION SWITCH PROVIDE NEW DOOR POSITION INDICATOR SWITCH BY SENTRY SECURITY FASTENERS, IN. SS-701665 200MRS-TB MAGNETIC DOOR POSITION SWITCH, ADJUSTABLE WITH TRIPLE BIAS, NON-HANDED. NEW DOOR POSITION ALARM SENSOR SHALL BE TIED INTO LOCAL CONTROL CENTER HOUSING UNIT 4 OR 5 AND BACK TO CONTROL CENTER IN ADMINISTRATION BUILDING.

AutoCAD SHX Text

ALARM

AutoCAD SHX Text

ALARM

AutoCAD SHX Text A1

AutoCAD SHX Text N1.

AutoCAD SHX Text NEW DOOR POSITION ALARM SENSOR SHALL BE TIED INTO LOCAL CONTROL CENTER IN HOUSING UNIT 4 OR 5 AND BACK TO CONTROL CENTER IN ADMINISTRATION BUILDING.

AutoCAD SHX Text

NOTES

AutoCAD SHX Text

NOTES

AutoCAD SHX Text N1

AutoCAD SHX Text P

AutoCAD SHX Text L

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text B

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text U

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text I

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text M

AutoCAD SHX Text S

AutoCAD SHX Text P

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text Q

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text P

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text S

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text

BID 7-2-267-2-26

FCPS

M C

SSCP

NCC

M P

A L B1 B2

SRS

EMERGENCY PUSH STATION

CODE BLUE STATION

TVSS

VFD

TRANSIENT VOLTAGE SURGE SUPPRESSION

VARIABLE FREQUENCY DRIVE

GLASS BREAK

DUPLEX RECEPTACLE

TEACHER STATION

ADMINISTRATION STATION

STUDENT STATION

CARD READER CO CARBON MONOXIDE DETECTOR

DOCK LIGHT FIXTURE

CONTROL MODULE

TELEPHONE / DATA OUTLET

DUTY STATION

STAFF STATION

STAFF REGISTER STATION

DOME LIGHT

DUAL BED STATION

SINGLE BED STATION

BED / LIGHT INTERFACE

PENDENT INTERFACE

EMERGENCY PULL STATION

MASTER STATION

NURSE CALL CONTROLLER

NURSE CALL

ADDENDUM NOTE

PLAN NOTE

DEMOLITION NOTE

THREE PHASE MOTOR

BELL

AUDIO / VIDEO INPUT

VIDEO INPUT

WALL MOUNTED SPEAKER / CLOCK COMBO

WALL MOUNTED SPEAKERS

DUAL FACE CLOCK

CCTV CONTROL PANELCCTV

SECURITY SYSTEM CONTROL PANEL

KEY PAD

BEAM DETECTOR

MOTION DETECTOR

DOOR CONTACT

CAMERA

MONITOR MODULE

FIRE CONTROL POWER SUPPLY

VISUAL ONLY UNIT

ELECTRICAL SYMBOLS LEGEND

SINGLE RECEPTACLE (120 VOLT)

EMERGENCY RECEPTACLE

DOUBLE DUPLEX RECEPTACLE

SINGLE FACE CLOCK

FLUSH FLOOR BOX

SURFACE FLOOR BOX

SPECIAL EQUIPMENT RECEPTACLE

TELEPHONE OUTLET

DATA OUTLET

POWER POLE

JUNCTION BOX

WALL JUNCTION BOX

PULL (JUNCTION) BOX

UNDERFLOOR JUNCTION BOX

OUTLETS

LIGHT FIXTURE

STRIP FIXTURE

IN-GRADE LIGHT FIXTURE

SPOTLIGHT (number of heads shown) EXIT SIGN (face & direction as shown)

WALL MOUNT LIGHT FIXTURE

CEILING LIGHT FIXTURE

TRACK & FIXTURE

STREET TYPE POLE FIXTURE

POLE MOUNTED LIGHT FIXTURE

EXTERIOR WALL MOUNT LIGHT FIXTURE

WALLPACK LIGHT FIXTURE

SPECIAL PURPOSE LIGHT FIXTURE

HIGH BAY LIGHT FIXTURE

EMERGENCY EGRESS LIGHT FIXTURE

(number of heads shown)

EMERGENCY LIGHT FIXTURE

FIXTURES

SWITCHES

SINGLE-POLE SWITCH

DIMMER SWITCH

TIME SWITCH

KEY SWITCH

MANUAL MOTOR SWITCH

THERMAL OVERLOAD SWITCH

SWITCH WITH PILOT LIGHT

FOUR-WAY SWITCH

THREE-WAY SWITCH

CIRCUITRY and RACEWAYS

UNDERFLOOR DUCT

BUS DUCT

PLUGMOLD AS SPECIFIED

WIREMOLD AS SPECIFIED

FLEXIBLE PIGTAILS/CONNECTIONS

"CONDUIT RUN CONTINUES" INDICATION

END OF CONDUIT RUN, CAP AND STAKE

END OF CONDUIT RUN

HOME RUN (with circuit numbers)

CONDUIT STUB DOWN

CONDUIT STUB UP

CONDUIT INSTALLED

MECHANICAL

ELECTRIC WATER HEATER

ELECTRIC UNIT HEATER

PIPE TRACE HEATER

RESISTANCE HEATER, KW SHOWN

SINGLE PHASE MOTOR

SOUND and SIGNAL

INTERCOM OUTLET

MICROPHONE OUTLET

TELEVISION OUTLET

CHIME

BUZZER

VOLUME CONTROL

SPEAKER

SERVICE and EQUIPMENT

THERMOSTAT

CAPACITOR

ENCLOSED CIRCUIT BREAKER

TRANSFER SWITCH

WIREWAY

GROUND CONNECTION PER N.E.C.

TELEPHONE TERMINAL BOARD

GENERATOR, KW SHOWN

CURRENT TRANSFORMERS

UTILITY METER, AS REQUIRED

WEATHERHEAD

PANELBOARD, FLUSH MOUNTED

PANELBOARD, SURFACE MOUNTED

COMB. STARTER

MAGNETIC STARTER

FUSED DISCONNECT SWITCH

TRANSFORMER

CONTROL

xxVA connection by x/C) IRRIGATION CONTROLLER (120 volt

LIGHTING CONTACTOR

CONTROL TRANSFORMER

buttons indicated) PUSHBUTTON STATION (number of TIME CLOCK (24 hour U.O.N.)

PHOTOCELL (voltage as required)

HUMIDISTAT

FIRE ALARM

TAMPER SWITCH (furnished by FP/C) FLOW SWITCH (furnished by FP/C)

FIREFIGHTER COMMUNICATION JACK

MAGNETIC DOOR HOLDER

REMOTE INDICATING LIGHT, CLG. MTD.

REMOTE INDICATING LIGHT, WALL MTD.

END OF LINE DEVICE

ANNUNCIATOR PANEL

FIRE ALARM CONTROL PANEL

PULL STATION

SPEAKER & LIGHT

SPEAKER

HORN

DUCT SMOKE DETECTOR

HEAT DETECTOR

SMOKE DETECTOR

HORN & LIGHT

DESIGNATIONS

(by E.C.)

(by others)

FACP

ANN

EOL

1,3

UFD

F S

SWITCH STYLE OCCUPANCY SENSOROC

DIGITAL TIME SWITCH

POWER PACK

DUAL TECHNOLOGY SENSOR - 360° - 500 SQ FT

DUAL TECHNOLOGY SENSOR - 360° - 1000 SQ FT

ULTRASONIC SENSOR - 360° - 2 CIRCUIT

OCCUPANCY SENSOR / PHOTOCELL

WALL MOUNT DUAL TECHNOLOGY SENSOR

OS5

OS4

OS2

OS3

OS1

DUCT SMOKE DETECTORF/S

CEILING MOUNTED WIFI

DIGITAL EQUIPMENT METER, AS REQUIRED

POLE

PUMP

PANEL

PNL

PVC

PRV-

P-

POLY VINYL CLORIDE

POWER ROOF VENTILATOR

PULL BOX

GENERAL CONTRACTOR

GROUND

HUMIDIFIERH-

GND

GFI

GROUND FAULT INTERRUPTER

ABBREVIATIONS LEGEND

POWER

SWITCH

RECEPT

SF-

SWBD

TCC

SPEC

RGC

RTU-

PWR

VOLTS

WATTS

UNO

UH-

TYP

ROOF TOP UNIT

RECEPTACLE

SWITCHBOARD

UNDER FLOOR

SPECIFICATIONS

RIGID GALVANIZED STEEL CONDUIT

UNLESS NOTED OTHERWISE

UNDERWRITERS' LABORATORIES, INC.

TAMPER PROOF RECEPTACLE

TAMPER PROOF SWITCH

TEMPERATURE CONTROL CONTRACTOR

VERIFY LOCATION WITH OWNER

TYPICAL

UNIT HEATER

SUPPLY FAN

WITH

WITHOUT

XFMR

W/O

TRANSFORMER

WEATHER PROOF

HOUR

LIGHT

JUNCTION BOX

LIGHT CONTROL

ISOLATED GROUND

HORSEPOWER

MINIMUM

MOUNT

MAKE-UP AIR UNIT

MOTOR CONTROL CENTER

MAIN LUG ONLY

MOUNTED

MOUNTING

MAXIMUM

LIGHTING

LT FLEX

MTD

MUAU-

MTG

MLO

MIN

MAX

MCC

LTG

IMC

HVAC

HOA

NORMALLY CLOSED

NOT IN CONTRACT

NORMALLY OPEN

NOT TO SCALE

NIGHT LIGHTNL

NTS

NIC

HAND-OFF-AUTO SELECTOR SWITCH

HEATING/VENTILATING/AIR CONDITIONING

INTERMEDIATE METAL CONDUIT

LIQUID TIGHT FLEXIBLE METAL CONDUIT

MECHANICAL CONTRACTOR

HID HIGH INTENSITY DISCHARGE

AFF

ACU-

AHJ

AHU-

B-

AIC

ATS

BLDG

CHLR-

CND (C)

CKT BKR

CKT

CUH-

CU-

DISC

DFU-

EF-

DWH-

EBB-

DWG

CT-

EXIST./EX.

EWC

FLEX

FLA

FLR

FSES

FLUOR

EMT

ABOVE FINISHED FLOOR

AIR CONDITIONING UNIT

AMPS

ABOVE COUNTER

AIR HANDLING UNIT

AUTOMATIC TRANSFER SWITCH

AMPS INTERRUPTING CAPACITY

AUTHORITY HAVING JURISDICTION

ABOVE SHELF

BOILER

BUILDING

BELOW COUNTER

CHILLER

DOMESTIC WATER HEATER

CABINET UNIT HEATER

CIRCUIT

CIRCUIT BREAKER

CONDUIT

CONDENSING UNIT

COOLING TOWER

DUCT FURNACE

DRAWING

DISCONNECT

FOOD SERVICE EQUIP. SUPPLIER

ELECTRIC WATER COOLER

ELECTRICAL CONTRACTOR

ELECTRIC BASEBOARD

ELECTRICAL METALLIC TUBING

EXISTING

EXHAUST FAN

FLOOR

FLUORESCENT

FLEXIBLE CONDUIT

FULL LOAD AMPS

EM EMERGENCY

F/S FIRE/SMOKE

FU- FURNACE

GENERAL ELECTRICAL NOTES

1. ALL WORK SHALL BE IN COMPLIANCE WITH THE 2023 MICHIGAN

ELECTRICAL CODE AND MDOC STANDARDS.

2. ALL NON-FIRE RATED WALLS ARE TO BE PATCHED WITH LIKE

MATERIAL TO MAINTAIN ORIGINAL RATING.

3. ALL WALL AND FLOOR PENETRATIONS THROUGH FIRE RATED WALLS

ARE TO BE SEALED WITH FIRE CAULK TO MAINTAIN ORIGINAL

RATING. EXISTING PENETRATIONS IN THE AREA OF WORK THAT ARE

NOT PROPERLY SEALED ARE TO BE SEALED TO MATCH THE RATING

OF THE WALL.

4. ALL CONDUITS SHALL BE FIELD ROUTED ALONG EXISTING PIPING

AND STRUCTURAL STEEL. CONDUITS SHALL BE INSTALLED

STRAIGHT, LEVEL, AND PARALLEL OR PERPENDICULAR TO THE

BUILDING LINES.

5. CONTRACTORS SHALL VISIT THE PROJECT SITE DURING PRE-BID

WALK THROUGH TO DETERMINE THE EXACT EXTENT OF THE WORK

REQUIRED BEFORE BIDDING THE PROJECT.

6. REMOVE ALL EXISTING OBSOLETE EXPOSED CONDUIT, WIRE, AND

EQUIPMENT NOT TO BE RE-USED WHERE WORK IS BEING DONE

EXCEPT ITEMS NOTED OTHERWISE.

7. WHERE BUILDING SURFACES ARE DAMAGED BY THE REMOVAL OF

OLD WORK, SURFACES SHALL BE PATCHED AND PAINTED TO MATCH

ADJACENT.

8. ISTING WORK, WHICH IS PRESENTLY CONCEALED, WHICH WILL

REMAIN CONCEALED, AND DOES NOT INTERFERE WITH ANY NEW

WORK OF ANY TRADE NEED NOT BE REMOVED. HOWEVER, ALL

CONDUIT SHALL BE CAPPED BELOW FINISH SURFACE AND THEN

PATCHED AND PAINTED TO MATCH, OR AS NOTED.

9. STING OPENINGS, WHICH ARE TO BE REUSED, SHALL BE MODIFIED

OR ENLARGED TO SUIT THE NEW SYSTEMS AS REQUIRED. PROVIDE

ALL REQUIRED CUTTING AND PATCHING.

10. RACTOR SHALL BE RESPONSIBLE FOR PATCHING THE EXISTING

WALLS TO MATCH THE ADJACENT SURFACES BEHIND ALL SURFACE

MOUNTED EQUIPMENT.

11. RACTOR SHALL FIELD VERIFY ALL EQUIPMENT AND LOADS PRIOR TO

INSTALLING SERVICE TO EQUIPMENT.

12. INGS ARE BASED ON EXISTING RECORD DOCUMENTS AND CASUAL

FIELD OBSERVATION. REPORT ANY DISCREPANCIES TO ENGINEER

FOR CLARIFICATION.

1. CONDUITS AND BOXES:

1.1. 3/4" MINIMUM TRADE SIZE.

1.2. EMT TYPE CONDUIT IS APPROVED WITH COMPRESSION

FITTINGS.

1.3. NO PVC ALLOWED INSIDE OF BUILDINGS.

1.4. CONDUITS SHALL BE ATTACHED WITH TWO-HOLE STRAPS.

SINGLE HOLE STRAPS ARE NOT PERMITTED.

1.5. NO SET SCREWS ARE ALLOWED.

1.6. TAMPER-PROOF SCREWS REQUIRED FOR EXPOSED CONDUIT

AND BOXES MOUNTED BELOW TEN FEET.

1.7. DRIVE PIN ANCHORS USED ON MASONARY OR CONCRETE

WALLS/CEILINGS.

2. MINIMUM RACEWAY SIZE; 3/4" TRADE SIZE. ALL FLEXIBLE CONDUIT

RACEWAYS SHALL BE LIQUID TITE, MAXIMUM 72" LENGTH AND MUST

BE APPROVED BY PSC AND MDOC PROJECT MANAGER. REFER TO

SPECIFICATION 260533 - RACEWAY AND BOXES FOR ELECTRICAL

SYSTEMS.

3. INSTALLATION OF ANY NEW OR REWORKED CONDUIT, FITTINGS, AND

STRAPS SHALL FOLLOW CURRENT NEC AND MDOC STANDARDS.

4. CONDUIT, CONDUIT INSTALLATION, AND BOXES BEING REUSED

SHALL BE BROUGHT UP TO CURRENT MDOC STANDARDS.

5. ALL CONDUIT AND BOXES ABOVE 10 FOOT OR IN

MECHANICAL/ELECTRICAL ROOMS, SHALL MEET THE FOLLOWING

REQUIREMENTS:

5.1. STRAP DISTANCE: 5 FEET.

5.2. FASTENERS: 2 HOLE.

5.3. CONDUIT” INTERIOR EMT, EXTERIOR EXPOSED/CONCEALED-

GRC.

5.4. FITTINGS: COMPRESSION.

5.5. BOXES: STANDARD BOXES FOR ENVIORNMENT INSTALLED TO

MEET N.E.C.

5.6. SECURE CONDUIT WITHIN 12 INCHES OF BOXES AND

ENCLOSURES.

6. ALL CONDUIT AND BOXES 10 FOOT AND BELOW SHALL MEET THE

FOLLOWING REQUIREMENTS:

6.1. STRAP DISTANCE: 3 FEET.

6.2. FASTENERS: 2 HOLE WITH SECURITY SCREWS.

6.3. SECURITY HARDWARE:

6.3.1. TORX T-25 WITH CENTER REJECTION PIN.

6.3.2. HEX HEAD CONCRETE SCREWS WITH NO SCREWDRIVER

SLOT.

6.3.3. EXPANSION POUND-IN ANCHORSWITH NO SCREWDRIVER

SLOT THAT DO NOT REQUIRE TO BE EXPLOSIVELY DRIVEN.

6.3.4. PRE-APPROVED HARDWARE.

6.4. CONDUIT: INTERIOR EMT, EXTERIOR EXPOSED/ CONCEALED -

GRC.

6.5. FITTINGS: COMPRESSION

6.6. BOXES:

6.6.1. SURFACE MOUNTED:

6.6.1.1. BELL BOX: FS TYPE, WITH SQUARE HEAD KO SEAL.

6.6.1.2. NO KNOCKOUTS - DRILL AS REQUIRED.

6.7. SECURE CONDUIT WITHIN 12 INCHES OF BOXES AND

ENCLOSURES.

7. ALL EXPOSED WIRING SHALL BE IN CONDUIT.

8. ALL WALLS THAT ARE ACCESSIBLE SHALL BE FISHED AND DEVICE

CUT INTO WALL.

9. ALL LOCATIONS WHERE THE WALLS CAN NOT BE FISHED SHALL BE

SURFACE MOUNTED CONDUIT FOLLOWING NOTES 14 THROUGH 15

ABOVE.

10. ALL EXTERIOR CONCEALED CONDUIT UNDERGROUND SHALL BE

RNC/HDPE SCHEDULE 80. ALL EXTERIOR ABOVE GROUND CONDUIT

SHALL BE RGC UP TO 10 FEET ABOVE GRADE. PROVIDE UL LISTED

#12 COPPER TRACER WIRE TO ALL UNDERGROUND CONDUITS

INSTALLED FOR LOW VOLTAGE.

11. ALL ELECTRICAL OUTAGES SHALL NOT LAST OVER 2-HOURS. IF A

WINDOW OF GREATER THAN 2 HOURS FOR AN ELECTRICAL SHUT

DOWN OR CUT OVER IS REQUIRED, THEN A PORTABLE GENERATOR

SHALL BE USED TO REPLACE POWER TO ALL PERIMETER DETCTION,

VIDEO MANAGEMENT, LINE SAFTEY, AND ANY OTHER ELECTRICAL

SERVICE REQUIRED. ALL OUTAGES AND CUT OVERS SHALL BE

COORDINATED A MINIMUM OF 2-WEEKS PRIOR TO WORK, INCLUDING

AN HOUR BY HOUR SCHEDULE, MUST BE SUBMITTED TO MDOC

LEADERSHIP AND THE FACILITY FOR REVIEW.

12. WHEN RELOCATING ANY ELECTRICAL DEVICE, CONTRACTOR SHALL

COMPLETE THE RELOCATION IN ONE DAY AND VERIFY THAT ALL

DEVICES RELOCATED ARE WORKING PROPERLY PRIOR TO LEAVING

THE SITE.

13. CONTRACTOR SHALL PROVIDE AND INSTALL ALL REQUIRED

COMPONENTS, RACEWAYS, WIRE, AND HARDWARE, AS INDICATED

ON DRAWINGS.

14. CONTRACTOR SHALL PROVIDE UPDATED PANEL SCHEDULES FOR

ALL PANELS AFFECTED BY THIS PROJECT. UPDATED SCHEDULES

SHALL BE PRINTED AND INSTALLED ON THE INSIDE COVER OF THE

PANEL.

15. ALL WORK COMPLETED WITHOUT APPROVED SHOP DRAWINGS IS AT

CONTRACTOR'S RISK.

16. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF

ALL 24V CONTROL WIRING AS REQUIRED TO LOCALLY CONTROL ALL

HVAC & PLUMBING IN ACCORDANCE WITH THE SEQUENCE OF

OPERATIONS. REFER TO THE MECHANICAL DRAWINGS FOR ALL

LOCAL THERMOSTAT LOCATIONS AND MECHANICAL SPECIFICATIONS

FOR INSTALLATION REQUIREMENTS. COORDINATE IN FIELD WITH

MECHANICAL CONTRACTOR AS REQUIRED. ELECTRICAL

CONTRACTOR SHALL PROVIDE AND INSTALL ALL CONDUIT, WIRE,

AND HARDWARE AS REQUIRED IN ACCORDANCE WITH ELECTRICAL

SPECIFICATIONS. REFER TO SHEET E-100 DETAIL 1 FOR ADDITIONAL

INFORMATION.

17. CONTRACTOR SHALL NOTIFY PSC OF ANY EXISTING INSTALLATIONS

NOT MEETING THESE STANDARDS PRIOR TO STARTING WORK IN THE

AREA.

18. UPON RELOCATING LIGHTS AND CAMERAS CONTRACTORS SHALL

VERIFY THAT THE LIGHTS AND CAMERAS ARE WORKING PROPERLY

PRIOR TO LEAVING THE SITE.

19. CONTRACTOR SHALL USE MDOC APPROVED POLES AND FIXTURES,

NO ALTERNATES WILL BE ALLOWED. ALL OTHER STATE OF MICHIGAN

AGENCY SPECIFICATIONS DO NOT APPLY.

20. CONTRACTOR SHALL NOT ADD MORE THAN 20% CAPACITY TO ANY

PANEL.

21. ARC FLASH LABELS TO BE PROVIDED FOR ALL NEW PANELBOARDS.

22. NEW PRINTED CIRCUIT DIRECTORIES SHALL BE PROVIDED FOR ALL

NEW AND REVISED PANELBOARDS.

23. CONTRACTOR SHALL SUBMIT AN RFI FOR ANY NON-CODE

COMPLIANT ELECTRICAL EQUIPMENT OR ELECTRICAL INSTALLATION.

AN RFI RESPONSE WILL BE PROVIDED GIVING DIRECTION ON HOW

TO PROCEED.

GENERAL HVAC NOTES

1. ALL WORK SHALL CONFORM TO MICHIGAN MECHANICAL CODE,

LATEST APPLICABLE EDITION.

2. INSTALL ALL EQUIPMENT, MATERIALS, AND ACCESSORIES PER

MANUFACTURERS WRITTEN INSTRUCTIONS.

3. ALL EXISTING SYSTEMS (INCLUDING EXHAUST FANS, FIN TUBE)

THAT SERVES AREAS BEING RENOVATED SHALL BE REBALANCED

AS REQUIRED.

4. NOTIFY OWNER OF ANY PIPING OR DUCTWORK DEMOLITION THAT

MAY AFFECT NORMAL OPERATION OF OTHER AREAS.

5. FIELD VERIFY LOCATIONS OF EXISTING PIPING THAT MAY CONFLICT

WITH NEW CONSTRUCTION AND RELOCATE AS NEEDED.

6. CONTRACTOR SHALL COORDINATE ALL WORK WITH OTHER

DISCIPLINES PRIOR TO CONSTRUCTION TO AVOID CONFLICTS.

7. PROVIDE MANUAL AIR VENTS WITH 3/4" HOSE CONNECTION AT ALL

HIGH POINTS.

8. OFFSET PIPING TO ACCOMMODATE LARGE DUCTWORK.

9. THE CONTRACTOR SHALL FIELD VERIFY THE SIZES, LOCATION,

ELEVATIONS, AND DETAILS OF ALL EXISTING CONDITIONS THAT MAY

AFFECT THE WORK.

10. THE CONTRACTOR SHALL BE RESPONSIBLE FOR MAINTAINING THE

INTEGRITY OF ALL EQUIPMENT AND MATERIALS IN A "NEW"

CONDITION DURING CONSTRUCTION.

11. ALL WORK SHALL BE PERFORMED BY LICENSED CONTRACTORS

AND SUBCONTRACTORS AS REQUIRED BY LAW.

12. IF THERE IS CONFLICTING INFORMATION IN THE PLANS OR

SPECIFICATIONS THE MORE STRINGENT AND GREATER COST ITEM

SHALL BE USED.

13. DRAWINGS INDICATE REQUIRED SIZES AND POINTS OF

TERMINATION OF PIPES AND DUCTS AND SUGGESTED ROUTES. IT

IS NOT INTENTION OF DRAWINGS TO INDICATE ALL NECESSARY

OFFSETS. INSTALL WORK IN MANNER TO CONFORM TO

STRUCTURE, AVOID OBSTRUCTIONS, PRESERVE HEADROOM AND

KEEP OPENINGS AND PASSAGEWAYS CLEAR. DO NOT SCALE FROM

DRAWINGS.

14. PERFORM WORK IN ACCORDANCE WITH THE LATEST EDITIONS,

REVISIONS, AMENDMENTS, OR SUPPLEMENTS OF APPLICABLE

STATUTES, ORDINANCES, CODES OR REGULATIONS OF FEDERAL,

STATE, AND LOCAL AUTHORITIES HAVING JURISDICTION IN EFFECT

ON THE DATE BIDS ARE RECEIVED.

15. WHERE APPROVED STANDARDS HAVE BEEN ESTABLISHED BY OSHA,

UNDERWRITERS, LABORATORIES, AMERICAN CODES, ASA, ASHRAE,

ARI, NEC, STATE FIRE INSURANCE REGULATION BODY, NFPA OR

OTHERS, THESE STANDARDS SHALL BE FOLLOWED WHETHER OR

NOT INDICATED ON THE DRAWING AND SPECIFICATIONS.

16. DUCT/PIPING LAYOUT IS SCHEMATIC. EXACT LOCATION OF

DUCT/PIPING AND EQUIPMENT SHALL BE COORDINATED WITH

BUILDING STRUCTURE, EQUIPMENT FURNISHED, ARCHITECTURAL

DRAWINGS, AND ALL OTHER TRADES PRIOR TO INSTALLATION. ANY

CONTRACTOR INSTALLING WORK WITHOUT PRIOR COORDINATION

SHALL RELOCATE HIS WORK AT HIS EXPENSE TO ALLOW PROPER

INSTALLATION OF ANY AND ALL TRADES WORK.

17. UNLESS OTHERWISE NOTED, ALL DUCT/PIPING SHALL BE

CONCEALED WHEREVER POSSIBLE. PROVIDE CHROME

ESCUTCHEON OR ALUMINUM DUCT COLLAR AT EACH PENETRATION

OF A FINISHED SURFACE.

18. DUCT/PIPING SHALL NOT BE RUN ABOVE ELECTRICAL GEAR IN THE

SERVICE SPACE REQUIRED BY THE NATIONAL ELECTRICAL CODE.

19. ANY ADDITIONAL LOW VOLTAGE CONTROL WIRING THAT IS

REQUIRED SHALL BE PROVIDED BY THE HVAC CONTRACTOR.

CONTROL WIRING SHALL BE RUN IN CONDUIT IF REQUIRED BY

LOCAL CODES OR THE SPECIFICATIONS. POWER SHALL BE

PROVIDED BY THE ELECTRICAL CONTRACTOR.

20. ALL PIPING SHALL BE CONCEALED ABOVE THE CEILING SPACE, IN

NEW METAL CHASES, OR WITHIN THE EXISTING FIN TUBE

ENCLOSURES.

21. CONTRACTOR TO TRACK AND PROVIDE PAPERWORK TO OWNER OF

THE AMOUNT OF MATERIAL BEING RECYCLED THROUGHOUT THE

PROJECT.

22. CONTRACTOR TO PATCH, PRIME, AND PAINT EXISTING

WALLS/CEILINGS AS NEEDED TO MATCH EXISTING WHERE

DEMOLITION AND/OR NEW WORK IS COMPLETED.

23. ALL FASTENERS USED IN AREAS EXPOSED TO INMATES SHALL USE

TAMPERPROOF SCREWS.

24. CONTRACTOR TO REFER TO ALL ELECTRICAL CONSTRUCTION

DOCUMENTS AND DIVISION 26 SPECIFICATIONS FOR CONTROL

WIRING RACEWAYS. ALL CONTROL WIRING RACEWAYS ARE TO

MEET MDOC REQUIREMENTS.

25. CONTRACTOR WILL HAVE 1 ESCORT TO WORK WITH THROUGH AT

THE PROJECT.

26. CONTRACTOR TO NOTIFY THE FACILITY AT LEAST 1 DAY IN

ADVANCE FOR ANY HOT WORK TO ALLOW THE OWNER TO DISABLE

THE FIRE ALARM.

27. CONTRACTOR TO ATTEND A 6 MONTH AND AN 11 MONTH POST

CONSTRUCTION MEETING WITH THE ENGINEER AND OWNER TO

REVIEW AND FIX ISSUES DURING THE WARRANTY PERIOD.

MECHANICAL SYMBOLS LEGEND

HVAC PIPING SYMBOLSHVAC PIPING

HVAC DUCTWORK

F/S F/S s s

TEMPERATURE CONTROL SYMBOLS

MISCELLANEOUS NOTES

HVAC DUCTWORK SYMBOLS HVAC DUCTWORK & DIFFUSER TAGS HVAC PIPING VALVES

MECHANICAL ABBREVIATIONS

AFF ABOVE FINISH FLOOR

AC AIR COMPRESSOR

AHU AIR HANDLING UNIT

AS AIR SEPARATOR

A.T.C. ARCHITECTURAL TRADES CONTRACTOR

B BOILER

B.A.S. BUILDING AUTOMATION SYSTEM

CAF COMBUSTION AIR FAN

CC COOLING COIL

CFM CUBIC FEET PER MINUTE

CHLR CHILLER

CHP CONSOLE HEAT PUMP

CONV CONVECTOR

CT COOLING TOWER

CU CONDENSING UNIT

CUH CABINET UNIT HEATER

CV CONTROL VALVE

CWP CHILLED WATER PUMP

DB DRY BULB

DFU DUCT FURNACE

DIA DIAMETER

DN DOWN

DPR DAMPER

DS DUCT SILENCER

EAT ENTERING AIR TEMPERATURE

EF EXHAUST FAN

EG EXHAUST GRILLE

E.T.C. ELECTRICAL TRADES CONTRACTOR

EVR EVAPORATOR

EWT ENTERING WATER TEMPERATURE

EXH EXHAUST

EXIST EXISTING

FF FINISH FLOOR

FPM FEET PER MINUTE

FT FEET

FTR FINNED TUBE RADIATION

FU FURNACE

GAL GALLON

GFRH GAS FIRED RADIANT HEATER

GR GRILLE

H HUMIDIFIER

HC HEATING COIL

HD HEAD (FT)

HP HORSE POWER

HHP HORIZONTAL HEAT PUMP

HTG HEATING

HVAC HEATING, VENTILATION, & AIR CONDITIONING

HWP HEATING WATER PUMP

HX HEAT EXCHANGER

ID INSIDE DIAMETER

I.E. INVERT ELEVATION

IAH INTAKE HOOD

LAT LEAVING AIR TEMPERATURE

LH LATENT HEAT (MBH)

LWT LEAVING WATER TEMPERATURE

MAX MAXIMUM

MBH BTU PER HOUR (THOUSAND)

MIN MINIMUM

M.T.C. MECHANICAL TRADES CONTRACTOR

N.C. NOISE CRITERIA

NFPA NATIONAL FIRE PROTECTION ASSOCIATION

NTS NOT TO SCALE

P PUMP

PCR PUMPED CONDENSATE RETURN

PD PRESSURE DROP

RCP RADIANT CEILING PANEL

REQ'D REQUIRED

RG RETURN GRILLE

RH RELATIVE HUMIDITY

RLH RELIEF HOOD

RTU ROOF TOP UNIT

SD SUPPLY DIFFUSER

SF SUPPLY FAN

SG SUPPLY GRILLE

SH SENSIBLE HEAT (MBH)

SM SHEET METAL

SQ. FT. SQUARE FEET

SST SATURATED SUCTION TEMPERATURE

STR STRAINER

TC TOTAL COOLING (MBH)

TCL TEMPERATURE CONTROL

T&P TEMPERATURE & PRESSURE RELIEF VALVE

TYP TYPICAL

UH UNIT HEATER

VAV VARIABLE AIR VOLUME BOX

VRH VARIABLE AIR VOLUME REHEAT BOX

FPVAV FAN POWERED VARIABLE AIR VOLUME BOX

V.F.D VARIABLE FREQUENCY DRIVE

ZD ZONE DAMPER

X-SA EXISTING ITEM (EXISTING SUPPLY AIR DUCT)

ITEM

EXISTING

CHILLED WATER SUPPLY

CHILLED WATER RETURN

CONDENSATE DRAIN

CONDENSER WATER SUPPLY

CONDENSER WATER RETURN

COOLING TOWER WATER SUPPLY

COOLING TOWER WATER RETURN

DIRECT EXPANSION

HEAT PUMP WATER SUPPLY

HEAT PUMP WATER RETURN

HEATING WATER SUPPLY

HEATING WATER RETURN

SUCTION (REFRIGERANT)

LIQUID (REFRIGERANT)

SUCTION (DIRECT EXPANSION)

LIQUID (DIRECT EXPANSION)

LOW PRESSURE STEAM (0-20 LBS.)

MEDIUM PRESSURE STEAM (21-75 LBS.)

HIGH PRESSURE STEAM (76 LBS. & ABV.)

STEAM CONDENSATE (GRAVITY)

PUMPED STEAM CONDENSATE

STEAM CONDENSATE BOILER FEED

GATE VALVE

GAS COCK

CHECK VALVE

BALANCE COCK

CIRCUIT SETTER

TWO-WAY CONTROL VALVE

THREE-WAY CONTROL VALVE

GLOBE VALVE

BALL VALVE

SOLENOID VALVE

EXPANSION VALVE WITH

THERMOSTATIC BULB

PLUG VALVE

BUTTERFLY VALVE

RELIEF VALVE

HOSE & DRAIN END VALVE

PRESSURE RELIEF VALVE

PRESSURE REDUCING VALVE

TRIPLE DUTY VALVE

GAS PRESSURE REGULATOR

STRAINER (BLOW-OFF)

FLOW DIRECTION

PIPING DROP

PIPING RISE

INLINE PIPING DROP

INLINE PIPING RISE

PIPING TEE

PIPING ELBOW

THERMOMETER

PUMP

UNION

PIPE ANCHOR

PIPE GUIDE

BACK FLOW PREVENTER

PIPE CAP

PIPE BREAK

THERMOMETER WELL

EXPANSION LOOP

EXPANSION COMPENSATOR

THERMOSTAT

PROGRAMMABLE THERMOSTAT

THERMOSTAT (W/ NIGHT SETBACK)

ROOM SENSOR

HUMIDISTAT

PRESSURE GAUGE

DAMPER (ELECTRIC OPERATION)

DAMPER (PNEUMATIC OPERATION)

DAMPER BLADES

SUPPLY AIR DUCT

EXIST SUPPLY AIR DUCT

RETURN AIR DUCT

EXIST RETURN AIR DUCT

OUTSIDE AIR DUCT

EXIST OUTSIDE AIR DUCT

EXHAUST AIR DUCT

EXIST EXHAUST AIR DUCT

SUPPLY AIR DUCT RISER

RETURN AIR DUCT RISER

OUTSIDE AIR DUCT RISER (AS NOTED)

EXHAUST AIR DUCT

INSULATED DUCTWORK (AS NOTED)

SUPPLY AIR DIFFUSER (SQUARE)

SUPPLY AIR DIFFUSER (INLINE)

TURNING VANES

SURFACE MTD. GRILLE

SUPPLY AIR DIFFUSER (ROUND)

90° TEE W/45° APPROACH

CONICAL TAKE-OFF

CONICAL TAKE-OFF W/ DAMPER

BALANCE DAMPER

RETURN AIR DUCT BOOT

ECCENTRIC REDUCER

CONCENTRIC REDUCER

VERTICAL FIRE DAMPER

EXISTING VERTICAL FIRE DAMPER

HORIZONTAL FIRE DAMPER

EXISTING HORIZONTAL FIRE DAMPER

VERTICAL SMOKE DAMPER

HORIZONTAL SMOKE DAMPER

VERTICAL FIRE / SMOKE DAMPER

HORIZONTAL FIRE / SMOKE DAMPER

DUCT SMOKE DETECTOR, INSTALLED BY M.T.C.,

PROVIDED & WIRED BY E.T.C.

UNIT HEATER

CEILING EXHAUST FAN

ROOF MOUNTED EXHAUST FAN

DEMOLITION

POINT OF CONNECTION BETWEEN NEW AND

EXISTING

POINT OF EXISTING TO REMAIN AND EXISTING

TO BE REMOVED

INDICATES PLAN NOTE

INDICATES DEMOLITION NOTE

DETAIL BUBBLE

DETAIL NUMBER

PAGE LOCATION INDICATES

DIRECTION OF DETAIL SECTION

XXXX

X-OA

X-EA

X-SA

X-RA

SCP

DXS

DXL

CTR

HPR

HPS

CTS

CWR

CWS

LPS

MPS

HPS

SC (BF)

TAG CFM

NECK REMARKS

SIZE

SD-1 250

8"ø ---

T P

T N

1. SEE ARCHITECTURAL DRAWINGS FOR ADDITIONAL INFORMATION.

2. EXISTING EQUIPMENT LAYOUT IS SCHEMATIC. EXACT LOCATION OF EXISTING

DUCT/PIPING AND EQUIPMENT SHALL BE COORDINATED WITH BUILDING

STRUCTURE, EQUIPMENT FURNISHED, ARCHITECTURAL DRAWINGS AND ALL

OTHER TRADES PRIOR TO DEMOLITION.

3. PERFORM WORK IN ACCORDANCE WITH THE LATEST EDITIONS, REVISIONS,

AMENDMENTS, OR SUPPLEMENTS OF APPLICABLE STATUTES, ORDINANCES,

CODES OR REGULATIONS OF FEDERAL, STATE, AND LOCAL AUTHORITIES

HAVING JURISDICTION IN EFFECT ON THE DATE BIDS ARE RECEIVED.

4. WHERE APPROVED STANDARDS HAVE BEEN ESTABLISHED BY OSHA,

UNDERWRITERS LABORATORIES, AMERICAN CODES, ASA, ASHRAE, ARI, NEC,

STATE FIRE INSURANCE REGULATION BODY, NFPA OR OTHERS. THESE

STANDARDS SHALL BE FOLLOWED WHETHER OR NOT INDICATED ON THE

DRAWING AND SPECIFICATIONS.

5. COORDINATE CUTTING AND PATCHING WITH GENERAL CONTRACTOR.

6. ALL BOLD DASHED LINES INDICATE ITEMS TO BE REMOVED UNLESS NOTED BY

KEYNOTE. ALL OTHER…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Jul 7, 2026.