Solicitation Amendment N0010425RK0650006 SF 30.pdf

R

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers is extended. is not extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

(a) By completing items 8 and 15, and returning copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NUMBER AS DESCRIBED IN ITEM 14.

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER

NUMBER IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print) 16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

15B. CONTRACTOR/OFFEROR

(Signature of person authorized to sign)

15C. DATE SIGNED 16B. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

16C. DATE SIGNED

Previous edition unusable STANDARD FORM 30 (REV. 11/2016) Prescribed by GSA FAR (48 CFR) 53.243

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE PAGE OF PAGES

2. AMENDMENT/MODIFICATION NUMBER 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQUISITION NUMBER 5. PROJECT NUMBER (If applicable)

6. ISSUED BY CODE 7. ADMINISTERED BY (If other than Item 6) CODE

8. NAME AND ADDRESS OF CONTRACTOR (Number, street, county, State and ZIP Code) (X) 9A. AMENDMENT OF SOLICITATION NUMBER

9B. DATED (SEE ITEM 11)

10A. MODIFICATION OF CONTRACT/ORDER NUMBE

10B. DATED (SEE ITEM 13)

CODE FACILITY CODE

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

Block 14 (Description of Amendment/Modification): The purpose of this amendment is to extend the solicitation due date to 1/8/2026 and respond to the following questions:

Q1: Aft Cable Keeper - Dimension 1.25in, DWG Section B2: Dimension appears to be incorrect, Outer Diameter is 1in. and appears to be tangent to both upper radius and lower flat. If this is true, then Radius 0.03in DWG Section B1 is incorrect. Please provide dimensional clarification.

A1: Confirming the 1.25-inch dimension is incorrect - it should have been drawn to the line just below, or it should have been marked as 1.00. The R.

03 dimensions refer to the chamfer on the edges of the bracket.

Q2: Cable Spec - 3.2.2.5 Inner Jacket: The specification calls for heat shrink jackets over the wire. Would an extruded jacket be permissible as an alternate to the heat shrink jacket?

A2: The utilization of heat shrink is notably good for sealing, color coding, bundling, and strain relief. The extruded jacket technique appears to be for protecting entire cable runs and is a more permanent installation. Immediate concern is with the extruded jacket technique being too stiff. Initial response is no. However, I will note that any drawing deviations must be approved via a waiver/Request for Variance. Providing an affirmative in this format would not warrant the change as it does not provide the official review/signature.

Q3: BOM ITEM 29 - 2510015-001: We did not receive a drawing/specification for this potting compound. What is the MFG potting compound and corresponding manufacturer's part number?

A3: Source Control drawing has been added to the TDP. This drawing has a table with the MFG Cage/Name/Address and Part Number for the Potting Compound.

Q4: Drawing Note 4L - Section C-C on sh. 3: Note states not to apply silicone to item 15 when installing item 11. There is no callout showing item 15 on item 11 on the diagram. Is this talking about item 5 on sub-assy drawing for item 11 (PN 6894530)?

A4: Yes - the note should refer to item 5 on the sub-assy drawing for item 11 (6894530). It is important that the preformed packing on item 11 does not have any lubricant applied as the intent of this item is to provide a sufficient hold within the housing.

Q5: Ink Marking Requirement, 6894530, 6894535: Are we allowed to laser mark the arrangement instead of ink-marking?

A5: Can you create a white marking with laser marking? The current ink color is white. Also, would laser marking have a great effect on the surface of the part? Note that any drawing deviations must be approved via a waiver/Request for Variance. Providing an affirmative in this format would not warrant the change as it does not provide the official review/signature.

Section A - Solicitation/Contract Form

The following changes have been made:

INFORMATION FROM TO

Response Due Date 22 Dec 2025 08 Jan 2026

N0010425RK0650006

P O BOX 2020, 5450 CARLISLE PIKE

MECHANICSBURG, PA 17050-0788

UNITED STATES

Mckenzy Harris, Email: mckenzy.s.harris.civ@us.navy.mil Telephone: 7176051368 AdminBy:

SCD: PAS: