SOW_Appendix_A_(Capability_Matrix).pdf

Mobile Reflective Imaging System Statement of Work Appendix A: Requirements Matrix

Req. # Capability Description Threshold (T) Objective (O) Vendor Response 1 Environmental Operating Requirements

1.1 Able to operate exposed to the outdoor

environment without canopies or other structures

Operates in all forms of precipitation (e.g., rain, sleet, freezing rain, hail, and snow), direct sunlight, high humidity and salinity levels, and airborne and accumulating particles (e.g., blowing dust, sand, small debris, snow and ice)

O=T

1.2 Able to operate in extreme temperatures -30ºC to 50ºC (-22ºF to 122 ºF) -40ºC to 60ºC (-40ºF to 140 ºF)

1.3 Able to withstand high wind speeds 128 kph (80 mph) O=T

2 System Performance Requirements

2.1 Able to produce images without the need of

a boom or other device located on an opposite side of the conveyance to conduct mobile scanning

Produces images (executes inspections) without the need of a boom or other device located on an opposite side of the conveyance while moving

O=T

2.2 Able to conduct scanning operations within a

short period of time after startup

Becomes fully operational to conduct scanning within 20 minutes of startup in all environmental operating conditions described in Section 1.

Becomes fully operational within 5 minutes of startup in all environmental operating conditions described in Section 1.

2.3 Able to conduct multiple unique inspections

of conveyances in a series in a single pass

Scans and produces images of up to 5 targets (each target 40ft in length) without stopping from the slowest operating speed up to 5.0 mph.

System shall be able to initiate next subsequent scan, with no more than 10 feet between conveyances.

Scans and produces images of up to 10 targets (each target 40ft in length) without stopping from the slowest operating speed up to 8.0 mph.

System shall be able to initiate next subsequent scan, with no more than 10 feet between conveyances.

2.4 Able to scan the target area for the full field

of view

Scans and produces images of the conveyance, from 0 to 14 ft. and 6 in.

high and up to 125 ft. long (for example, a truck tractor with trailing units).

O=T

2.5 Able to conduct inspections while stationary Scans and produces images of a conveyance moving 3 mph while the system is stationary. The stationary scan mode shall include automatic x-ray beam termination for conveyances that stop or travel at a rate that could subject vehicle occupants to radiation above 10 µR per scan.

O=T

2.6 Able to operate using either shore power or

an independent onboard power system while stationary

Scans and produces images of the conveyance while stationary using shore power and using an independent onboard power system

O=T

2.7 Able to discriminate between low density and

high density materials

Generates images of the conveyance that reveals different densities of materials via different color shades

O=T

2.8 Able to discriminate between organic (low Z)

materials and metallic (high Z) materials.

Generates images of the conveyance that reveals organic material without the use of image enhancement tools when the organic material is blocked and/or surrounded by high Z material.

O=T

2.9 Able to detect organic substances Detects at least 4 lbs. of organic material with an approximate density of 0.4 g/cc in 4 inch x 8 inch x 1.5 inch packages placed directly behind 0.24 inches of steel with the bricks stacked in the direction of the x-ray beam and with the 4 x 8 inch brick face facing the x-ray source (perpendicular to x-ray beam) at a distance of 2 ft. with the target traveling through the system at a speed of 3.0 mph.

Detects at least 2 lbs. of organic material with an approximate density of 0.4 g/cc in 4 inch x 8 inch x 1.5 inch package placed directly behind 0.24 inches of steel with the bricks stacked in the direction of the x-ray beam and with the 4 x 8 inch brick face facing the x-ray source (perpendicular to x-ray beam) at a distance of 2 ft. with the target traveling through the system at a speed of 3.0 mph.

2.10 Able to meet or exceed quality requirements

for reflection-based images as measured in accordance with ANSI N42.46-2008 procedures

Penetrates at least 6 mm (~0.24") of steel and achieves a Spatial Resolution of 15 mm (~0.59”), a Layer Contrast of 7 mm (~0.28”), and an Isolation Contrast of 2 mm (~0.08”) at a distance of 50cm (19.69") with the target traveling past the system at a speed of 3.0 mph (stationary and while moving).

Penetrates at least 8 mm (~0.31") inches of steel and achieves a Spatial Resolution of 10 mm (~0.39”), a Layer Contrast of 3 mm (~0.12”), and an Isolation Contrast of 0.5 mm (~0.02”) at a distance of 50cm (19.69") with the target traveling past the system at a speed of 3.0 mph (stationary and while moving).

2.11 Able to display radiographic images created

by the system

Displays the radiographic images of the entire length and height of the scanned conveyance at 256 gray levels in near real-time such that the image is displayed during the scan with a delay of no more than three seconds.

O=T

2.12 Able to enhance images via image analysis

tools available to the operator (Signal Processing)

User able to Change the magnification; Select different color palettes; Optimize the image’s contrast and brightness; Sharpen the image; Establish Regions of Interest;

Annotate the image

Meets threshold signal processing requirements and employs "Smart Signal Processing" that automatically identifies anomalies that could be drugs, explosives, weapons and potential casings for radioactive materials is an Objective. This may include system auto-generated identification of regions of interest such as anomaly cueing/annotation, identification and denotation of conveyance areas that were not penetrated, and change detection of a previously scanned conveyance (image compare).

2.13 Able to store records with conveyance

identification data (e.g. license plate, shipping container number, etc.) and scan images

Locally stores 21,600 commercial truck tractor and trailer/containers scan records per system (15 scans per hour x 16 hours x 90 days)

Locally stores 175,000 total records per system (20 scans per hour x 24 hours x 365 days)

2.14 Able to export scan images in a .tif and .jpg

file formats and export Image Data Set (IDS) records in .pdf file format

Exports scan images in .tif and .jpg file formats and IDS records--complete with images, vehicle information, and operator notations--in .pdf file formats. The .tif image shall contain the image’s full dynamic gray level range.

O=T

2.15 Able to retrieve and export stored files, records, and scan images

Locally stored files, records, and scan images to are accessible to operators and able to copy to removable media storage devices: encrypted, FIPS 140-2 Level 2 and FIPS 197 compliant or greater flash and hard drives

2.16 Able to permanently save user selected

records, which will be protected from overwrite or auto-delete features

User able to permanently save user selected records (at all operator levels) that are protected from overwrite or auto-delete features. All records identified as "suspect records" are permanently saved and protected. Other records may be permanently saved besides "suspect records" as selected by users.

Operator Level 3 only able to delete permanently saved and protected records.

O=T

2.17 Able to perform automated data overwrite

functions

Begins auto-overwriting records after 90 days, not including "suspect records" and other records that have been permanently saved and protected by users. Provides automated storage capacity warnings at 70% and 90% system storage limits. Automated data overwrite features can be turned on/off by Operator Level 3 users.

O=T

2.18 Able to achieve optimal scanning results

while moving

Informs the driver whether the system is moving too fast or slow for optimal scanning results

Includes one or more of the following features:

- Maintains system speed for optimal scanning results through a speed control device that can be set by the driver, with the option be turned on or off

- Image aspect ratio auto-correction to ensure images are distortion-free regardless of fluctuations in scan speed or distance

2.19 Able to be connected to CBP and DHS

computer networks

Meets network security requirements and includes hardware and software compatibility that enables future wireless network connectivity. (Reference minimum Technical Requirements Specifications for laptops and desktops, Sections 7 and 8)

Meets network security requirements and includes hardware and software compatibility that enables future wireless network connectivity and distributed image analysis. (Reference enclosed Technical Requirements Specifications for laptops and desktops Sections 7 and 8, and data formatting specification, section 3.8)

2.20 Able to capture shipping container and

license plate information in the IDS data file.

User able to enter shipping container identifying information and vehicle license plate information

O=T

2.21 Able to collect container scan counts and a

total scans count.

Records the total number of scans for the system

Records the total number of shipping containers scanned (operator identified) and total scans for the system

3 X-Ray System Design Requirements (Applies to all chassis configurations)

3.1 Have imaging system technology that does

not rely on radioactive isotopes

System is based on X-Ray technology O=T

3.2 Have reflective imaging technology Produces images without the need of a boom or other device, either attached or detached from the vehicle, located on an opposite side of the conveyance to conduct transmission-based imaging

3.3 Have scanning device on the passenger side

of the vehicle.

System scans target conveyance located on the passenger side of the vehicle to scan targets while moving in the direction of traffic

O=T

3.4 Have acceptable dose rates levels for scanned

drivers and/or passengers

Dose rates are no greater than 10 µR per scan when the system is operating at its slowest scan speed

O=T

3.5 Have a controlled area which limits the

potential exposure to personnel outside of this area to below 50 µR in any one hour.

The radiation control area shall be no greater than 25 ft. from the edge of the beam side of the vehicle and no greater than 5 ft. from the front, back, and non-beam sides of the system when the system is operating at its slowest scan speed and while stationary

O=T

3.6 Have equipment to sufficiently mark off the

controlled area

The system be equipped with 12 standard 36 in. rubber safety cones and 6 radiation exposure warning signs in English/ Spanish/French that can hang on the cones

O=T

3.7 Have safety features (interlocks (access panel

and operational), indicators and controls, auto termination, and labeling)

- Safety Interlocks cannot be disabled or overridden by an operator for any reason;

- “Emergency Stop” switches/buttons (including one on the operator console), audible/visual operating signals, and traffic control signals;

- Automatic x-ray beam termination if a target vehicle stops within the imaging area or travels at a rate that could subject vehicle occupants to radiation above 10 µR per scan while in stationary mode

- Automatic x-ray beam termination if the scanning vehicle stops while in mobile scanning mode

O=T

3.8 Have proper information formatting Is N.25 Ver. 1.6.0.0 and Pride 2.0 ICD ver. 5 compliant

O=T

3.9 Have User Tracking - Each scan shall be

tagged with the User’s name and that name shall be displayed with the Data Set.

Each scan is tagged is with the user's name and displayed with the data set

Each scan is tagged is with more than one user when multiple operators review the scanned image and each user is displayed with the data set

4 Vehicle Chassis Configuration Requirements

4.1 Regular Cab Configuration

4.1.1 Able to accommodate 2 officers Comfortably seats 2 officers wearing law enforcement duty belts. Size of an average officer is ~6 feet tall and 225lbs.

O=T

4.1.2 Able to maneuver in congested environments No greater than 51 feet wall-to-wall turning radius (i.e. the turning radius that takes into account front-end overhang) with a wheel base no longer than 170 inches

No greater than 42 feet wall-to-wall turning radius (i.e. the turning radius that takes into account front-end overhang) with a wheel base no longer than 145 inches

4.2 Crew Cab Configuration

4.2.1 Able to accommodate 4 officers. . Comfortably seats 4 officers wearing law enforcement duty belts. Size of an average officer is ~6 feet tall and 225lbs.

4.2.2 Able to maneuver in congested environments No greater than 60 feet wall-to-wall turning radius (i.e. the turning radius that takes into account front-end overhang) with a wheel base no longer than 180 inches

No greater than 50 feet wall-to-wall turning radius (i.e. the turning radius that takes into account front-end overhang) with a wheel base no longer than 160 inches

4.3 Applies to all Chassis Configurations

4.3.1 The chassis shall be a standard commercial

chassis Chassis is capable of being serviced by ASE certified mechanics. No military specified chassis shall be accepted.

O=T

4.3.2 Have a vehicle and system design that does

not require Commercial Driver's License

Total weight shall not exceed 26,000 lbs. or the Gross Vehicle Weight Rating, whichever is less

O=T

4.3.3 Have automatic transmission with 4 wheel

drive

Capable of operating in inclement weather conditions with 4 wheel drive

O=T

4.3.4 Have acceptable ground clearance Minimum ground clearance of 7 in.

and withstands driving over pot holes, train tracks, and unimproved rough roads

Minimum ground clearance of 8 in.

and withstands driving over pot holes, train tracks, and unimproved rough roads

4.3.5 Have engine block heater Equipped with engine block heaters for cold weather environments

O=T

4.3.6 Have a security system Equipped with manufacturer's

security system and keyless entry

O=T

5 Vehicle Coach Design Requirements (Applies to all chassis configurations)

5.1 Have a wide-angle rear view camera and

monitor

Safety feature to enable full rear view of van for use by the driver when the system's gear selection is placed in reverse

O=T

5.2 Have audible back-up warning Safety feature for use by the driver when the system's gear selection is placed in reverse

O=T

5.3 Have storage area for equipment and work

supplies and a means to securely store equipment

Stores control area marking equipment and other mission support supplies

O=T

5.4 Have LED lighting each operated (on/off) on

separate switches: law enforcement, target conveyance, area, and spot lighting

- Blue law enforcement lights mounted to the front, sides, and rear of the vehicle, each law enforcement lighting also operated (on/off) on separate switches.

- Target Conveyance lighting provides sufficient light to read and capture conveyance identifying information, extending 180 degrees 10 feet from the vehicle center point on the scanning side of the vehicle

- Area lighting provides sufficient light to read and capture photographic images of truck and conveyance identifying information, extending 360 degrees 20 feet from the vehicle center point.

- Equipped with a driver side post mount spot light that allows the driver to control rotation and elevation of the spotlight outside of vehicle.

5.5 Have an on-board 120VAC 60Hz Generator

that utilizes the same fuel type as the vehicle.

The Generator shall be capable to produce all the power required to fully operate the system and all its sub-systems, all cabin and coach electrical systems, to include a 12VDC power supply/charger to run all the 12VDC circuits and charge the vehicle and/or coach batteries.

The Generator shall be capable to produce all the power required to fully operate the system and all its sub-systems, all cabin and coach electrical systems, to include a 12VDC power supply/charger to run all the 12VDC circuits and charge the vehicle and/or coach batteries by drawing on the same fuel source (tank) as the vehicle. The generator should automatically shut off if the fuel level falls below 1/4th of the tank capacity.

5.6 Have power cable for shore power One 100 foot power cable capable of running enough power for all electrical systems and operations, with a marine grade twist-lock connector.

O=T

5.7 Have a power cable adaptor Include an adaptor for a NEMA 5-15p (15 Amp) plug.

O=T

5.8 Have a color printer System is equipped with a color

printer that is protected from physical and environmental damage to print scan images and data files

O=T

5.9 Have a First Aid Kit A Department of Transportation

(DOT) approved first aid kit shall be provided and mounted in the service body

O=T

5.10 Have a Spare Tire and associated tools Equipped with a full size spare tire and tools to replace tires

O=T

5.11 Have security system and remote entry Equipped with one complete alarm system for all the service body doors

O=T

5.12 Have Fire Extinguishers Two (2) fire extinguishers (one 2.5 lbs. / one 5 lbs.) shall be installed in the service body

O=T

6 Vehicle Cabin Design Requirements (Applies to all chassis configurations)

6.1 Have an adjustable operator station that

includes a laptop or a combination of a monitor and keyboard with mouse touchpad, image analysis software, and required system operation controls (turning system on, initiating and terminating scans).

Operator station that is center mounted, can swivel to be accessible to the driver or operator, and able to adjust height, telescoping, and tilt angle. The mount should not block access to cup holders. The operator station includes a 13" monitor or laptop screen with keyboard with PKI token/PIV card reader, mouse touchpad, imaging software, system controls. (Reference Technical Requirements Specifications for laptops and desktops, Sections 7 and 8)

Operator station that is center mounted, can swivel to be accessible to the driver or operator, and able to adjust height, telescoping, and tilt angle. The mount should not block access to cup holders. The operator station Operator station includes a 15" monitor or laptop screen with keyboard with PKI token/PIV card reader, mouse touchpad, imaging software, system controls.

(Reference Technical Requirements Specifications for laptops and desktops Sections 7 and 8)

6.2 Have a public address system Allows to the driver/operator to communicate to others via a public address system

O=T

6.3 Have a climate controlled cabin and other

passenger areas

Maintains temperatures between 60- 80F while idle or moving fully occupied to capacity with electronics and other equipment on and running while idling or running off of shore power

O=T

6.4 Have tinted windows Window tint is within applicable

limits / regulations / standards

6.5 Have additional interior lighting Have supplemental interior lighting to assist night time operations

O=T

7 Minimum Laptop Technical Requirements Specification (Reference Requirement 2.19 of this Capability Matrix)

7.1 Base Unit Factory presets for Energy Star 6.0

EPEAT Gold & Silver certifications Docking stations, peripherals, AC adapters interchangeable

In addition to meeting Threshold, have an inverted motherboard for improved thermals, allows notebook to run cooler and accessibility for easier service

7.2 Battery and Features Minimum 3-Cell (40 Whr) Lithium

Polymer battery with express charge . Standard battery last minimum 8 hours

4-Cell (54 Whr) Lithium Polymer battery w/express charge, lasts more than 8 hours more with optional battery slice. Ability to charge your battery to 80% in an hour. Ability to configure standard charge vs.

express charge. Battery extender optional, snaps to bottom of laptop to extend laptop runtime. LED battery life/health gauge. Tap once to view % charge, tap and hold to see overall health of battery, indication of when battery is nearing end-of-life

7.3 Processors 5th Gen Intel Core i5 or i7 processors

or equivalent

6th Gen Intel Core i5 & i7; Intel Xeon Processor E3-1200 v5 family

7.4 Chipset 5th Gen Intel integrated (Wildcat

Point LP) or equivalent

Intel C236 Chipset equivalent or better

7.5 Memory Minimum 8GB 1600 MHz DDR3; 2

slots supporting up to 16GB

16 GB 1600 MHz DDR3

7.6 Hard Drive Up to 512GB Mobility Solid State

Drive; 256GB SED SSD, Free Fall Sensor (FFS) Parks disk heads when it detects a fall to protect hard disk and data from shock.

Up to 1TB Mobility Solid State Drive;

512GB SED SSD, Free Fall Sensor (FFS) Parks disk heads when it detects a fall to protect hard disk and data from shock.

7.7 External Hard Drive (Optional) 256GB SSD, FIPS compliant FIPS 140- 2 Level 2

O=T

7.8 Video Card Intel Integrated HD Graphics 5500 or

equivalent

Discrete video card with 1GB or more of video memory, compatible with OpenGL 3.2, Shader Model 4.0 or later

7.9 Video Output HDMI or mDP (Standard), DVI and

VGA (Optional)

O=T

7.10 Display LED Backlit, anti-glare display with

variable brightness settings and Ambient light sensor to automatically adjust screen and keyboard brightness based on light conditions (see requirement 3.22 for additional information)

O=T

7.11 Keyboard Standard laptop keyboard with

keypad features, Backlit keyboard with Multi-touch touchpad

O=T

7.12 Input Touchpad Required, Pointing stick

(Optional)

O=T

7.13 Optical Drive (optional) 8X DVD +/-RW minimum capable of read/write for DVD and CD-ROM

O=T

7.14 Multimedia High quality speakers, headset/mic

combo jack, noise reducing array microphones, Webcam

7.15 Network Card Integrated NIC support 10/100/1000

Gigabit Ethernet Wake on LAN (WOL) capable WOL configurable to LAN only.

WLAN only, or LAN WLAN

O=T

7.16 Wireless Networking Integrated 802.11 AC

Airplane mode hardware switch to instantly turn on/off Wi-Fi, Bluetooth, and mobile broadband.

Ability to enable/disable wireless devices in BIOS (security feature), includes WLAN, Mobile Broadband, and Bluetooth

O=T

7.17 Mobile Broadband Support individual broadband

provider (e.g. Verizon, AT&T, and Sprint), Support individual broadband provider (e.g. Verizon, AT&T, and Sprint) or vehicle-based 4G/Wi-Fi connectivity. Embedded antenna array to enhance range and performance, WiGig

7.18 Power Management Able to set power on Everyday or

Weekday at the time set in Auto Power Time.

Able to set Low Power Mode on/off to conserve power Able to set different Suspend Modes to conserve power System can be powered up remotely from Suspend, Hibernate or Off when Low Power Mode is Off.

When Low Power Mode is on, the system can only be powered up remotely from Suspend.

O=T

7.19 Sound Card Integrated Intel High Definition

Audio with digital microphone, headphone/speaker out, mic jack

O=T

7.2 Expandable IEEE-1394 (for connecting DV

cameras, external disks, etc.), Minimum 2 M.2 expansion slots

O=T

7.21 Ports SD 4.0 Memory card reader E-

docking connector, 3 USB 3.0, HDMI, mDP, Network Connector (RJ-45), SIM card slot, E-Dock: 2 m.2 expansion slots: 1 WWAN/SSD and 1 WLAN/BT/WiGig. Integrated smart card reader. Lock slot

O=T

7.22 Security Trusted Platform Module (TPM)

version 1.2 or greater Smartcard reader slot , Steel-reinforced lock slot, (allows user to secure laptop to fixed object, like desk). NFC contactless smart card reader (Optional)

7.23 Features Bios flash upgrade capability must be

provided. Raid 0 or 1 for additional performance data protection (Optional) BIOS multi-level security settings, including Administrator password, System boot password, BIOS password. Ability to store Asset tag or other tracking number in BIOS (this is in addition t the service tag stored in BIOS. Computrace tracking capability in BIOS (like Lo-Jack for computers) (Optional).Ability to integrate system management with in-house tools, including ability to remotely manage BIOS updates and BIOS settings. Hardware-based logging of BIOS changes, vendor diagnostic, thermal, and power events. Useful for helpdesk diagnostics and security tracking (logs stored in BIOS)

O=T

7.24 Management Features Ability to remotely diagnose and

repair a PC, even when it's powered down or the OS is inoperable.

Remote asset, HW, and SW inventory. Encrypted, Remote Power- On and Update

O=T

7.25 Services 3 years basic support: next business

day parts and labor onsite response.

Hardware documentations, manufacture applications and drivers provided via direct link or software update tool. Hard drive retention services (No RMA of failed drives).

Vendor must host their own manuals, drivers and applications for download. (No link to third party website). Secure website for latest OS hotfixes, driver updates, ISO creation (ImageDirect). Global service and support. Must be able to provide roadmap review every 6 months.

O=T

7.26 Operating System Support Windows 7 Ultimate or

Enterprise 64 bit or greater.

Capable of upgrade to later versions of Windows with bitlocker

O=T

7.27 Trusted Platform Module (TPM) TPM version 1.2 or greater O=T 8 Minimum Desktop Technical Requirements Specification (Reference Requirement 2.21 of this Capability Matrix)

8.1 Energy Efficiency Ships from factory preset to Energy

Star 6.0 Cat A, B, C, or D rating.

Complies with Executive Order (E.O.)

13423, Part 23 of the Federal Acquisition Regulation (FAR), and Department of Homeland Security Management Directive 025-01, Sustainable Practices for Environmental, Energy and Transportation Management and Executive Order 13514 Federal Leadership in Environmental, Energy, and Economic Performance, Section 2(h)(i).

Manufacturer must meet EPEAT Silver certification at a minimum with progress towards Gold certification.

EPEAT Gold Certification.

8.2 Base Unit • ATX, Micro-ATX, or BTX chassis, with power supply and motherboards uniquely designed to manage heat throughout the system.

• Thermal-management technology using variable speed fans for additional cooling, while using less power and generating less noise.

• Thermal Sensor — Measures the incoming ambient air temperature to appropriately control internal cooling and helps improve thermal reliability.

O=T

8.3 Power Supply 240 W 90% efficient PSU (80Plus

Platinum Certified) Energy Star Compliant; 180W 85% efficient PSU (80 Plus Bronze Certified) Energy Star Compliant

365W 90% efficient PSU (80 Plus Gold Certified) Energy Star compliant; 290W 85% efficient PSU (80 Plus Bronze Certified) Energy Star Compliant

8.4 Processors 6th Gen Intel Core i5 & i7; Intel Xeon

Processor E3-1200 v5 family

O=T

8.5 Chipset Intel C236 Chipset equivalent or

better

O=T

8.6 Memory Minimum 8GB 1600 MHz DDR3; 2

slots supporting up to 16GB

16 GB 1600 MHz DDR3

8.7 Hard Drive Up to 512GB Mobility Solid State

Drive; 256GB SED SSD, Free Fall Sensor (FFS) Parks disk heads when it detects a fall to protect hard disk and data from shock.

Up to 1TB Mobility Solid State Drive;

512GB SED SSD, Free Fall Sensor (FFS) Parks disk heads when it detects a fall to protect hard disk and data from shock.

8.8 Video Card Integrated Intel HD Graphics 4600, equivalent or better. (2) Digital display out DVI or HDMI w/VGA & DVI Adapters for dual monitor support

Discrete video card with 1GB or more of video memory, compatible with OpenGL 3.2, Shader Model 4.0 or later

8.9 Optical Drive (optional) 16X DVD +/- RW O=T

8.10 Network Card • Integrated NIC support

10/100/1000 MB/s

• Wake On LAN capable.

8.11 Power Management • Able to set power on Everyday or

Weekdays at the time set in Auto Power Time.

• Able to set Low Power Consumption Mode on/off to conserve power.

• Able to set different Power Suspend Modes to conserve power (Monitor, CPU, Hard Drive).

• System can be powered up remotely from Power Suspend, Off, or Low Power Consumption Mode

O=T

8.12 Sound Card Integrated High Definition Audio O=T

8.13 Keyboard & Mouse • USB 104 Keyboard W/PIV Reader

• USB Optical Mouse

O=T

8.14 USB Connections (4) USB 3.0 Up to 10 USB connections on the unit - of which minimum (4) USB 3.0

• 6 rear and 4 front recommended configuration on the unit

8.15 Expandable Minimum 2 available usable PCI slots

to add optional cards as needed.

• Firewire card may use one of these slots as needed.

O=T

8.16 Standard Ports • (1) RJ45 • (1) Serial

•(1) VGA•(2) PS/2;• (2) Display ports/DVI or HDMI); Dual VGA or DVI to dual VGA cable provided for dual monitor support •Line in Stereo/microphone •Line out headphone/speaker

O=T

8.17 Optional/External Ports Optional Parallel/Serial port support O=T

8.18 Security • Trusted Platform Module version

1.2 or greater; chassis lock slot support; optional chassis Intrusion switch, Setup/BIOS password, I/O interface security

8.19 Features • BIOS flash upgrade capability must

be provided.

• Desktop and smaller form factor workstation

• Toolless design case, all parts except motherboard can be serviced and swapped without tools. Power supplies, disks, cards, optical drives, fans all serviceable without tools.

• Raid 0 or 1 for additional performance or data protection.

• Chassis Intrusion switch (can notify helpdesk and logs when chassis is opened).

• BIOS multi-level security settings, including Administrator password, System boot password, BIOS password.

• Ability to store Asset tag or other tracking number in BIOS (this is in addition to the service tag stored in

BIOS).

• Ability to override password reset jumper (if machine is lost/stolen, can’t just pull jumper to reset BIOS passwords).

• Ability to integrate system

8.2 Services • 3 Years Basic Support: Next

Business Day Parts and Labor Onsite Response.

• Hardware Documentations, Manufacture Applications and Drivers provided via CD or DVD.

• Hard Drive Retention Service (No RMA of failed drives)

• Vendor must host their own manuals, drivers and applications for download. (No link to third party website).

• Global service and support.

• Must be able to provide roadmap review every 6 months.

O=T

8.21 Operating System Support Windows 7 Ultimate or

Enterprise 64 bit or greater.

Capable of upgrade to later versions of Windows with bitlocker

ATTACHMENT 2