EXHIBIT A - SCOPE OF SERVICES.pdf
PDF 439 KB Posted
- Attached to
- ADAS Calibration and Wheel Alignment System
- Solicitation number
- OP143228
- Issued by
- California
About this file
This Scope of Services document outlines specifications for the Los Angeles County Metropolitan Transportation Authority (LACMTA) Invitation for Bid (IFB) No. OP143228 for the purchase of one new ADAS Calibration and Wheel Alignment System. The equipment must be delivered within 150 days from the contract effective date and must arrive at the designated location (Division 10 - Non-Revenue Maintenance Operation, 742 North Mission Road, Los Angeles, CA 90033) between Monday and Friday, 7:30 a.m. to 1:00 p.m. The contractor must notify LACMTA personnel two working days prior to delivery to allow for pre-delivery factory inspections and pre-acceptance. Delivery must be made via truck equipped with a lift gate, with the equipment fully charged or fueled upon arrival.
The equipment must be new, factory model year at the time of purchase award, and include all standard and required operational components at no additional cost to LACMTA. All components must be Original Equipment Manufacturer (OEM) items with no rebuilt, remanufactured, or unapproved aftermarket components acceptable. The equipment must comply with all applicable Federal, California State, and local regulations including FRA, AQMD, ARB, EPA Tier 4, and California Code of Regulations Title 8, section 8470. Payment terms are Net 30, with California sales tax applying to California dealers and use tax applying to out-of-state dealers. Final acceptance requires post-delivery inspection, verification of full operational status, compliance with technical specifications, resolution of all punch list items, and provision of operating and maintenance manuals along with training demonstrations.
View the file
Other files
Show all 34
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Specification Number MA-26-09
May 19, 2026
EXHIBIT A – SCOPE OF SERVICES
IFB No. OP143228
Equipment (Description): ADAS Calibration and Wheel Alignment System
1.0 Scope
1.1 This Contract is for the purchase of one (1) new ADAS Calibration and Wheel Alignment System. THE CONTRACTOR SHALL PROVIDE THE REQUESTED EQUIPMENT IN
FULL COMPLIANCE WITH LACMTA’S TECHNICAL REQUIREMENTS IDENTIFIED IN
EXHIBIT A.1.
1.2 The Contractor shall furnish, deliver, and warrant each equipment according to these specifications and shall include all items and/or accessories not mentioned, but required, for operation of the equipment.
2.0 General Requirements
2.1 All equipment classified as standard and/or required to operate the equipment shall be provided at no additional cost to LACMTA. Items inadvertently omitted from this specification that are classified and or otherwise designated by the equipment manufacturer as required to operate the specified equipment shall be brought to the attention of the designated LACMTA representative.
2.2 OEM & Aftermarket Components
The equipment with their components shall be new and of the latest factory model year released at the time the purchase order is awarded. They shall be complete, and ready to operate upon delivery. No rebuilt or remanufactured components will be acceptable. All components shall be Original Equipment Manufacturer (OEM), no aftermarket components shall be acceptable unless referenced in this specification and/or approved by the designated LACMTA representative.
All accessory installations shall be securely affixed and comply with OEM, Federal, State and OSHA standards. No installation shall interfere with the OEM systems nor render the equipment warranty invalid.
All electrical installations shall have all wires securely affixed to the running path. Wiring shall have protective shielding with loom, fabric, or PVC, as well as rubber grommets to protect wires that pass-through plates and panels, and insulated wire clamps for mounting. All accessory circuits shall have proper circuit protection adequately to prohibit damage to the unit’s OEM systems and prevent electrical shorts or fires.
2.3 Regulatory Compliance
The equipment shall be, at the date of the delivery, in compliance with all current applicable local, California State and Federal Code of Regulations.
Regulatory compliance shall include, but not limited to, compliance with all current and applicable Federal Railroad Administration (FRA), California State Air Quality Management District (AQMD), Air Resources Board (ARB), US Environmental Protection Agency (EPA)
Tier 4, California Code of Regulations, Title 8, section 8470 and local laws pertaining to this equipment. Contractors may be required to furnish proof of compliance.
2.4 Delivery Requirements
Requested delivery is within 150 days from date of Contract effective date.
Contractor must notify designated LACMTA personnel two (2) working days prior to equipment delivery to LACMTA so that LACMTA staff can make the necessary scheduling and travel arrangements to perform pre-delivery inspections and pre-acceptance of the equipment at the factory.
The equipment shall be prepared and cleaned before it is presented for the post-delivery inspection.
Delivery must be made Monday through Friday between 7:30am to 1:00pm.
It is the Contractor’s responsibility to make a delivery by a truck equipped with a lift gate to offload the equipment and any equipment to a location as designated by Metro personnel.
The equipment shall be delivered to Metro fully charged, if electric, or with a full fuel tank.
2.5 Delivery Location
All equipment shall be delivered to:
Los Angeles County Metropolitan Transportation Authority Division 10 - Non-Revenue Maintenance Operation 742 North Mission Road Los Angeles, CA 90033
Attention: Sona Darakjian Equipment Engineering Supervisor
2.6 Sales Tax & Use Taxes
California Sales Tax:
o California sales tax applies to all vehicles and/or other equipment purchased from a licensed California dealer.
o Dealers are required to collect taxes by invoicing LACMTA and then paying it directly to the BOE.
Use Tax:
o Use tax applies to all vehicles and/or other equipment purchased from an out-of-state dealer.
o Use tax is the liability of the buyer to pay at the time of registration either to the
DMV or BOE.
o Paying California use taxes on behalf of LACMTA by the sellers and/or manufacturers that are located out-of-state and not a licensed California dealer is not preferred per the California DMV manual and California Board of Equalization (BOE) publications.
If the Contractor elects not to pay use tax, tax will still be calculated on the price page at the rate indicated but will not be invoiced as LACMTA will pay use tax directly to the DMV.
If the seller unintentionally pays use taxes to California Board of Equalization (BOE) on behalf of Metro and then invoices Metro, the seller or manufacturer then must provide the following documents at the time of delivery:
o Proof of use tax payment to BOE o Seller’s BOE account/certificate
2.7 Inspection & Acceptance
The equipment shall not be inspected or accepted without prior compliance with this specification’s requirement.
The equipment shall be subjected to a pre-delivery inspection, if required, and to post-delivery inspection by LACMTA to determine if the equipment delivered are fully operational and in their final configuration, are in full compliance with the technical and performance specification and they did not sustain any damage upon delivery to LACMTA.
Final acceptance shall be made after post-delivery and installation inspection is performed by LACMTA to determine full compliance with the technical specification with all “punch list” items and pending issues are resolved and satisfied. This includes provision, if specified, operating and maintenance manuals, and training to demonstrate that the equipment is fully operational.
2.8 Technical Specification Compliance Requirements
The equipment must meet all requirements, including the technical requirements in Exhibit A.1.
2.9 Payments
Payment terms are Net 30. Refer to Contract Article IV – Compensation and Payment for additional requirements.
2.10 Invoices
Separate Invoices shall be provided for each equipment. The Contractor is responsible for submitting the original invoices to Accounts Payable. Refer to Contract Article IV – Compensation and Payment for additional requirements.
Each invoice must include the VIN number or serial number of the equipment delivered.
File details come from the government source that posted it. Updated .