EV00018063_Telecomm_Compliance.pdf

(2) NEW FORD BRONCO SPORT BIG BEND Per Specification Enclosed or Approved Equal – Advertisement Date: 10/12/2026 Bid Opening Date: 10/28/2026 EV00018063

Boston Police Telecommunications June 2026 Warning Equipment Specifications

1. BPD Equipment Power System

1.1. Email Radio@pd.boston.gov for all questions related to this section 1.2. A label or tag shall be placed near the equipment with installing firms name 1.3. This system is designed to disconnect power to as much equipment as possible when the key is in the OFF position

1.4. Include all hardware, connectors and parts to make a complete installation 1.5. No Snap Lock or insulation piercing connectors

1.6. All warning, computer and radio equipment will derive power from this system 1.7. All fuse blocks are to be located on the Lund Loft

1.8. NO Inline Fuse Holders, all circuits terminate at Fuse Blocks

1.8.1.Lightbar Main Power shall be a 40 amp auto reset circuit breaker

1.8.2.Main Siren Power shall be a 30 amp auto reset circuit breaker

1.9. All wiring will be Stranded, all sizes refer to American Wire Gauge

1.10. Main Circuit Breaker

1.10.1. 100 AMP Weather Proof Circuit Breaker

1.10.2. Mount so that circuit breaker is accessible under hood, as close to battery as possible 1.10.3. #4 AWG Red

Stranded wire from Battery to Circuit Breaker

1.10.4. #4 AWG Red Stranded wire from Circuit Breaker to Power Stud located in trunk area 1.11. Main Power

Point

1.11.1. Install Power Stud in trunk area

1.11.2. Use NYLOCK Nut and washer

1.11.3. Cover Exposed Terminal with Red Rubber Cap

1.12. Main Ground Point

1.12.1. Install Ground Stud in trunk area

1.12.2. Ground stud use NYLOCK Nut and washer

1.12.3. #4 AWG Black Stranded wire from ground stud to negative battery terminal

1.12.4. Cover exposed terminal with BLACK rubber cap

1.12.5. All warning equipment will ground to this point

1.12.6. No grounds shall be connected to the vehicle chassis

1.13. Constant Power Fuse Block

1.13.1. 6 position ATO style fuse block

1.13.2. #6 AWG Red Stranded wire from Power Stud to Fuse Block main power 1.13.3. This block shall be fed from a 40 AMP Auto Reset Circuit Breaker

1.13.4. Mount fuse block in trunk area

1.13.5. Label above Fuse block “Constant Power”

1.13.6. This block feeds the following equipment:

1.13.6.1. Sierra Wireless Modem (Red Wire)

1.13.6.2. Flash Light Charger

1.14. Ignition Power Fuse Block

1.14.1. 12 position ATO style fuse block

1.14.2. Wire block to a BOSCH 75 AMP relay then to Main power stub using # 6 AWG Red Stranded wire1.14.3. This block shall be fed from a 40 AMP Auto Reset Circuit Breaker

1.14.4. Mount fuse block in trunk area

1.14.5. Label above Fuse Block “Switched Power”

1.14.6. 75 AMP Relay, connect one side of coil to ground stud, the other side to an ignition switched feed from vehicle

1.14.7. This block feeds the following equipment:

1.14.7.1. Radio Chassis Power

1.14.7.2. Radio Control Head (Red Wire)

1.14.7.3. Radio Control Head (Yellow Wire)

1.14.7.4. Sierra Wireless Modem (White Wire)

1.14.7.5. Computer Docking Station Power Supply

1.14.7.6. Printer Power Supply

1.14.7.7. Dome Light

1.14.7.8. Map Light

1.14.7.9. USB Ports

1.14.7.10. Power Ports

1.15. An additional BOSCH 75 AMP relay shall be provided to provide switched power to the lightbar and siren, this relay will be fed from the main power point stud

1.15.1. This relay coil is to be connected in parallel with the relay providing power to the switched fuse block1.15.2. This relay will supply y Lightbar Main Power

1.15.2.1. The lightbar shall have a 40 amp auto reset circuit breaker

1.15.3. This relay will supply Main Siren Power

1.15.3.1. The siren shall be have a 30 amp auto reset circuit breaker

2. Equipment Cover

2.1. Provide and install LUND, LOFT-FPIU-EC

2.2. Provide appropriate brackets to mount LOFT-FPIU

Console / Interior

1. Provide and Install Red White LED Dome Light

2. Red White LED Gooseneck Light Mounted on console, ignition power

2.1. D&R P/N CA-0129

3. Two Magnetic Mic Clips (1 Siren, 1 Radio)

4. Run capped power feed for MDT and Printer

5. Run Cat 5 Cable from XR60 to front, next to power feed for MDT

Lights and Siren

1. Provide and Install Federal Signal Pathfinder PF200S17

1.1. Handheld Controller

1.2. All light heads will be set to steady burn, all flashing will be controlled by siren 1.3. Multi Color Buttons on Siren Controller

1.4. Program to be provided by Federal Signal Rep

1.5. DO NOT ADJUST PROGRAM FROM FEDERAL SIGNAL REP

1.6. Inputs

1.6.1. Park Kill – Siren Mute, White Light Cutoff on all light heads

1.6.2.Brake – REAR WARNING LIGHTS TO STEADY BURN

1.6.3.Horn Ring – used on Pos 2 and 3, WAIL, YELP, UNITROL ULTRA HI LO 1.6.4.IGN

1.7. Slide Switch

1.7.1.Position 1 – Rear Lights Only

1.7.2.Position 2 – Front Lights Only, ADD WHITE

1.7.3.Position 3 – ALL Lights and Siren

2. AUX Relay wiring from Siren to be brought to Terminal strip located near siren 2.1. 12

Position, 20 AMP, double row, screw terminal

2.2. GGE-20-12P-R or equivalent

3. QTY 2 Federal ES100 Speakers mounted under hood

4. QTY 1 ESB2-FPIUNDB Speaker Bracket

5. Provide and Install Federal Headlight WIG WAG module

6. QTY 2 Federal Signal MPS62U-BW mount in GRILLE

7. QTY 4 Federal Signal MPS63U-RBW with MPSM6-WIN mount Kit, Front Windshield 8. QTY 1 FEDERAL CN STICK

BLUE/BLUE/RED/BLUE/BLUE/AMBER/BLUE/BLUE rear windshield 9. QTY 2 Federal Signal MicroPulse Wide Angle Blue

White Under Mirror 10. QTY 2 Federal 416300X-BW, mounted on front fender, offset

11. QTY 2 Federal Signal MPS62U-BW, mounted on rear Tailgate, next to license plate

Radio / Antennas

1. Install Customer Supplied Kenwood HHCH Remount Mount Mobile Radio 1.1. Radio Power and

Ignition Power from Switched Fused Blocks

1.2. Install provided kenwood external speaker

2. Provide and Install, QTY 1, Panorama Antennas BPD-5385 (D)

2.1. Mount on roof, near rear of vehicle

3. Provide spreadsheet to BPD Telecom with Vehicle Number, Radio ID and SN, MDT CPU SN Provide all parts needed to make a complete install.

Equipment Locations need to be finalized with BPD Telecom before install.