EV00018011_Telecomm.pdf

(1) NEW PURSUIT INTERCEPTOR UTILITY AWD HYBRID MARKED Per Specification Enclosed or Approved Equal -

Advertisement Date: 09/28/2026 Bid Opening Date: 10/14/2026 EV00018011

Boston Police Telecommunications

June 2026 Warning Equipment Specifications

1. BPD Equipment Power System

1.1. Email Radio@pd.boston.gov for all questions related to this section 1.2. A label or tag shall be placed near the equipment with installing firms name 1.3. This system is designed to disconnect power to as much equipment as possible when the key is in the OFF position

1.4. Include all hardware, connectors and parts to make a complete installation 1.5. No Snap

Lock or insulation piercing connectors

1.6. All warning, computer and radio equipment will derive power from this system 1.7. All fuse blocks are to be located on the Lund Loft

1.8. NO Inline Fuse Holders, all circuits terminate at Fuse Blocks

1.8.1.Lightbar Main Power shall be a 40 amp auto reset circuit breaker

1.8.2.Main Siren Power shall be a 30 amp auto reset circuit breaker

1.9. All wiring will be Stranded, all sizes refer to American Wire Gauge

1.10. Main Circuit Breaker

1.10.1. 100 AMP Weather Proof Circuit Breaker

1.10.2. Mount so that circuit breaker is accessible under hood, as close to battery as possible 1.10.3. #4

AWG Red Stranded wire from Battery to Circuit Breaker

1.10.4. #4 AWG Red Stranded wire from Circuit Breaker to Power Stud located in trunk area 1.11. Main

Power Point

1.11.1. Install Power Stud in trunk area

1.11.2. Use NYLOCK Nut and washer

1.11.3. Cover Exposed Terminal with Red Rubber Cap

1.12. Main Ground Point

1.12.1. Install Ground Stud in trunk area

1.12.2. Ground stud use NYLOCK Nut and washer

1.12.3. #4 AWG Black Stranded wire from ground stud to negative battery terminal

1.12.4. Cover exposed terminal with BLACK rubber cap

1.12.5. All warning equipment will ground to this point

1.12.6. No grounds shall be connected to the vehicle chassis

1.13. Constant Power Fuse Block

1.13.1. 6 position ATO style fuse block

1.13.2. #6 AWG Red Stranded wire from Power Stud to Fuse Block main power 1.13.3.

This block shall be fed from a 40 AMP Auto Reset Circuit Breaker

1.13.4. Mount fuse block in trunk area

1.13.5. Label above Fuse block “Constant Power”

1.13.6. This block feeds the following equipment:

1.13.6.1. Sierra Wireless Modem (Red Wire)

1.13.6.2. Flash Light Charger

1.14. Ignition Power Fuse Block

1.14.1. 12 position ATO style fuse block

1.14.2. Wire block to a BOSCH 75 AMP relay then to Main power stub using # 6 AWG Red

Stranded wire1.14.3. This block shall be fed from a 40 AMP Auto Reset Circuit Breaker

1.14.4. Mount fuse block in trunk area

1.14.5. Label above Fuse Block “Switched Power”

1.14.6. 75 AMP Relay, connect one side of coil to ground stud, the other side to an ignition switched feed from vehicle

1.14.7. This block feeds the following equipment:

1.14.7.1. Radio Chassis Power

1.14.7.2. Radio Control Head (Red Wire)

1.14.7.3. Radio Control Head (Yellow Wire)

1.14.7.4. Sierra Wireless Modem (White Wire)

1.14.7.5. Computer Docking Station Power Supply

1.14.7.6. Printer Power Supply

1.14.7.7. Dome Light

1.14.7.8. Map Light

1.14.7.9. USB Ports

1.14.7.10. Power Ports

1.15. An additional BOSCH 75 AMP relay shall be provided to provide switched power to the lightbar and siren, this relay will be fed from the main power point stud

1.15.1. This relay coil is to be connected in parallel with the relay providing power to the switched fuse block1.15.2. This relay will supply Lightbar Main Power

1.15.2.1. The lightbar shall have a 40 amp auto reset circuit breaker

1.15.3. This relay will supply Main Siren Power

1.15.3.1. The siren shall be have a 30 amp auto reset circuit breaker

2. Equipment Cover

2.1. Provide and install LUND, LOFT-FPIU-EC

2.2. Provide appropriate brackets to mount LOFT-FPIU

3. Equipment Mounting

3.1. Mount all equipment on LOFT-FPIU-EC

3.2. ensure that all thumb screws can be accessed on the Radio Chassis Brackets

Console / Interior

1. Gamber Johnson Console (PN 71600411)

1.1. 2, 12 VDC Outlets, constant power

1.2. 2, USB Power Ports

2. Gamber Johnson CF33 Mount

2.1. CF-33 Dock, Gamber 7300-0196-02

2.2. Gamber Johnson 7300-0180 Keyboard and Gamber Johnson Mount

2.3. LIND DC Power Adapter, CF-LNDDC120

2.3.1. Powered from Ignition Power

2.4. All other Gamber parts required to make a complete mount to console 3. Provide and

Install Red White LED Dome Light

4. Red White LED Gooseneck Light Mounted on console, ignition power 4.1. D&R

P/N CA-0129

5. Two Magnetic Mic Clips (1 PA, 1 Radio)

5.1. Mounted on console – (Radio Mic on Top, PA mic on Side)

6. Cup holder (2 cups)

7. Gamber Johnson Armrest

8. Gamber Johnson Seat Belt Deflector Bracket

9. Brackets for Siren and Radio

9.1. Siren and Radio mount on Riser of console

9.2. Mount Radio Speaker on console rear, facing up

10. All Wiring in console needs to have 2-3 Feet of service slack 11. Provide and install Brother PJ-883 Printer and Mount

11.1. Gamber Johnson #7160-0430 Printer mount

11.2. 10’ USB Cable for Printer to Laptop Dock

11.3. Power Cable to Printer

11.4. Mount will be articulating type if no cage

11.5. Mount will be wall mounted if vehicle has cage

Lights and Siren

1. Provide and Install Federal Signal Pathfinder PF200S17-BOS17 1.1. All light heads will be set to steady burn, all flashing will be controlled by siren 1.2. Muli Color Buttons on Siren Controller

1.3. Program to be provided by Federal Signal Rep

1.4. DO NOT ADJUST PROGRAM FROM FEDERAL SIGNAL REP 1.5. PA

MIC

1.5.1.QTY 1 RMK Ext Kit

1.5.2.QTY 1 MNCTSD PA MIC

1.6. Inputs

1.6.1. Park Kill – Siren Mute, White Light Cutoff on all lightheads

1.6.2.Brake – REAR WARNING LIGHTS TO STEADY BURN 1.6.3.Horn Ring – used on Pos 2 and 3, WAIL, YELP, UNITROL ULTRA HI LO 1.6.4.IGN

1.7. Slide Switch

1.7.1.Position 1 – Rear Lights Only

1.7.2.Position 2 – Front Lights Only, ADD WHITE

1.7.3.Position 3 – ALL Lights and Siren

2. AUX Relay wiring from Siren to be brought to Terminal strip located near siren

2.1. 12 Position, 20 AMP, double row, screw terminal

2.2. GGE-20-12P-R or equivalent

3. QTY 2 Federal ES100 Speakers mounted under hood

4. QTY 1 ESB2-FPIUNDB Speaker Bracket

5. Provide and Install Federal Headlight WIG WAG module

6. QTY 2 Federal Signal MPS62U-BW mount in GRILLE

7. QTY 2 Federal MPS62U-BW mounted on hood

8. QTY 2 Federal 416300X-BW, mounted on front fender, offset

9. Provide and Install Federal Signal VALR51-BOS

9.1. BLUE/WHITE Front

9.2. BLUE REAR

9.3. 8 Center AMBER Signal Master

10. QTY 2 Federal Signal MPS62U-BW mount rear quarter panel

11. Rear Lighting, provide and install the following:

11.1. MPSM6-FPIURS2 Bracket with re seal kit

11.2. QTY 6 MPS62U

11.3. Colors looking at rear

11.4. DRIVERS SIDE BLUE,RED,BLUE

11.5. PASSENGER SIDE BLUE, AMBER, BLUE

12. QTY 2 Federal Signal MPS62U-BW, mounted on rear Tailgate, next to license plate

Radio / Antennas

1. Install Customer Supplied Motorola APX O5 Radio Mount Mobile Radio 1.1. Radio

Power and Ignition Power from Switched Fused Blocks

1.2. Connect Control Head Red and Yellow together to #14 AWG Yellow 2. Provide and Install, QTY 2, Panorama Antennas BPD-5385 (D) & BPD-5385 (P)

2.1. Mount on roof, near rear of vehicle

2.2. (D) on drivers side, (P) on passenger side

3. Provide and install Sierra Wireless XR60 Modem, with WiFi, 2 Ethernet ports Verizon Wireless 3.1.

Modem will be powered from Constant Fuse Block

3.2. Ignition will be wired to Switched Fuse Block

3.3. Connect GPS Port to Drivers Side, GPS Antenna

4. Provide and install, 25 foot, SLATE, Cat 5e, Male-Male Jumper

4.1. Connect to XR60 Ethernet Port 1

4.2. Connect to Gamber CF-33 Docking Station Ethernet Port

5. Provide spreadsheet to BPD Telecom with Vehicle Number, Radio ID and SN, MDT CPU SN

Provide all parts needed to make a complete install.

Equipment Locations need to be finalized with BPD Telecom before install.