Cleveland Community College Addendum #1.pdf

November 14, 2024

For: Cleveland Community College DEVITA Project # 24529

RECEIPT OF THIS ADDENDUM MUST BE NOTED ON THE BID FORM

ADDENDUM #1

TO ALL BIDDERS:

This addendum supplements and amends the original plans and specifications and shall be taken into account in the preparation of proposals and shall become part of the contract documents.

Attachments:

• Sign in attendance sheet from the pre bid 11/7/2024

• Pre bid agenda

• Rev. M1.1 Mechanical Floor Plan 11/14/2024

• Rev. E0.1 Electrical Schedules and Details 11/14/2024

• Rev. E0.2 Electrical Panel Schedules 11/14/2024

• Rev. E0.3 Electrical single Line Diagrams 11/14/2024

• Rev. E1.1 Electrical Plan 11/14/2024

• New G-001 Cover Sheet 11/14/2024 Questions and Answers:

1. The demolition plans are calling for demolition of the ductwork in the service corridor. Does all of the duct get removed or can it be reused if the appropriate size?

Answer: All the exiting HVAC ductwork is to be removed. They are over 50 years old and should not be reused.

2. Windows are identified as curtain wall on the plans but appear to be operable windows? Is there more of a description?

Answer: The windows are considered an Aluminum-Framed Storefront as described in specification section 084313, Aluminum-Framed Storefronts. The windows will opened by swinging out from the building.

3. The Drawings identify the main campus address for the building. Is there a more accurate address?

Answer: A cover sheet, G-001 has been created with a site map for clarification of the location.

• There will be a second Pre-Bid to be determined in Addendum #2 at Cleveland Community

College – 137 S. Post Rd., Jack Hunt Building – Board Room 2086, Shelby, NC 28152

• The bid opening is being rescheduled from 11/21/24 to be determined in Addendum #2 at

Cleveland Community College – 137 S. Post Rd., Jack Hunt Building – Board Room 2086, Shelby, NC 28152

END OF ADDENDUM #1

Meeting Agenda www.devitainc.com

877-4-DEVITA

corp@devitainc.com

Date: 11-07-2024

Sheet 1 and 2

Topic: Prebid Meeting

Meeting Date 11-07-2024

Time: 2:00P

Location: Cleveland Community College – 137 S. Post Rd., Jack Hunt Building –

Board Room 2086, Shelby, NC 28152

Attendance: Cleveland Community College o Stephen Matheny, VP mathenys508@clevelandcc.edu o Mark Fox foxm@clevelandcc.edu

DeVita o Michael Rogers mrogers@devitainc.com o

Agenda:

1. Review Project Scope

A. The scope of this project will be to provide ventilation, heating, and cooling to keep the building in the 65 F to 80 F range during the year.

B. A new electrical service will be required to accommodate the new HVAC equipment.

C. Owner desires to replace the existing windows with new double pane operable windows, which will be Alternate #1.

D. For alternate #2: The existing Federal Pacific panelboard will be replaced with a new panelboard. A new feeder will be required. This work is mandatory, but it will be priced as an alternate.

E. Bids will be received as a single prime contract F. The proposal will be a lump sum proposal

2. Questions A. We cannot provide responses to specific questions at this time by state bidding procedure. Any and all questions will be documented and responded to by Addenda.

B. The last day for questions will be Tuesday, November 12, 2024, NOON so we can respond to them via Addendum, no later than 7 days before bid opening.

3. Project Schedule A. Schedule for contract time of completion is currently 120 days from the NTP.

NTP is expected to occur around Mid-December, but not guaranteed B. Contractor shall be permitted to work 7:30 am to 5pm Mondays through Fridays.

C. Prior approval is required from Cleveland Community College and security to work outside these work hours.

D. There will be an establishment of a work zone perimeter around the facility involving the construction. Contractor and its employees must always remain within the designated work area.

Meeting Agenda www.devitainc.com

877-4-DEVITA

corp@devitainc.com

4. Liquidated Damages $200/day

5. Bidding Forms A. Sealed bid will be accepted at Cleveland Community College up until 3:00pm on

Thursday, November 21, 2024, in the Jack Hunt Building – Board Room 2086.

B. Provide the completed Bid Form of Proposal (leave Acceptance portion blank) C. Provide the Identification of HUB Certified/ Minority Business Participation form and Affidavit A or Affidavit B as part of the bid package.

D. Provide Form of Bid Bond as part of the bid package.

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

G0.1

COVER SHEET &

DRAWING INDEX

CM MR

CLEVELAND COMMUNITY COLLEGE

WELDING SHOP

CORRECTIONS FACILITY

260 KEMPER RD,

SHELBY, NC 28152

ISSUED FOR BID

OCT 29, 2024

WELDING SHOP

EXISTING GAS METER LOCATION

KEMPER RD

DRAWING INDEX

GENERAL

G001 COVER SHEET AND DRAWING INDEX X

ARCHITECTURAL

A101 FIRST FLOOR PLAN - DEMOLITION & RENOVATION X

A201 EXTERIOR ELEVATIONS - DEMOLITION X

A202 EXTERIOR ELEVATIONS - RENOVATION X

A601 WINDOW TYPE AND DETAILS X

MECHANICAL

M0.1 MECHANICAL LEGEND NOTES AND SCHEDULES X

M0.2 MECHANICAL DETAILS X

M0.3 MECHANICAL DETAILS II X

M1.0 MECHANICAL DEMO PLANS X

M1.1 MECHANICAL PLANS X X

ELECTRICAL

E0.1 ELECTRICAL LEGEND NOTES AND SCHEDULES X X

E0.2 ELECTRICAL PANEL SCHEDULE X X

E0.3 ELECTRICAL SINGLE LINE DIAGRAMS X X

E1.0 ELECTRICAL DEMO PLANS X

E1.1 ELECTRICAL PLANS X X

LOCATION MAP

NORTH

1 11/14/2024 ADDENDUM 1

IS

SU

ED

F

O R

B

ID

AD

D

EN

D

U M

MECH, ROOM

SERVICE CORRIDORTOILET

LAVATORY

SHOWER

MOP

ROOM TOILET TOILET

LOCKED

ROOMS

DOOR

COVER OVER OUTSIDE BOOTHS

SHOWER

42" WIDE

E

LE

C

TR

IC

A

L P

A N

E

LS

W

IN

D O

W

DOOR

8'-8" FLOOR TO CEILING

1ST WINDOW

4'-0" FROM

INSIDE CORNER

OVERHANG

7 BOOTHS THIS SIDE

TOILET TOILET

5 BOOTHS THIS SIDE

30" x 12" OA

B

B

24"x24" UP

22"x14" EA 32"x18" EA

22"x12" OA (BELOW)

32"x24" EA UP TO EF-1

20" x 10" EA32" x 18" EA26" x 16" EA

22"x12" OA (BELOW)

1 11

26x12" OA (BELOW)

1111111 1

111 1 1

E-A

1 1

MUA-2

2 WINDOWS

7'-0" FROM

INSIDE CORNER

OAU-1

232"x24" EA UP TO EF-2

30"x24" OA DN FROM OAU-1

28"x12" OA

28"x12" OA

28"x20" OA

28"x12" OA

28"x12" OA

28"x20" OAMUA-1

14"x12" OA

A

A

22"x12" OA22"x12" OA

14"x12" OA

14"x12" OA

M0.2

26"x16" EA

T

CONTROLS FOR MUA-1/EF-1 & MUA-2/EF-2

2" NG FROM ABOVE

1-1/4" NG FROM ABOVE

S-A

E-AS-A

S-A

S-B

S-A

S-B

EXISTING CHAIN LINK FENCE

~1 6'

-0

1-1/4" NG (ABOVE GROUND)

3" BURIED NG

GAS PIPING BURIED ON OUTSIDE SIDE OF FENCE

3" UP TO MUA-2 TEE, TRANSITION TO 2" NG UP TO ABOVE

24"x24" OA UP FROM OAU-1

24"x24" OA DN

OAU-1

(ON GRADE

BELOW)

"x

32"x24" EA FROM BELOW

EF-1 EF-226"Ø 26"Ø

32"x24" EA FROM BELOW

4 4

MUA-1

(ON GRADE BELOW)

MUA-2

(ON GRADE BELOW)

2" NG DN TO MUA-1

1-1/4" NG DN TO OAU-1

2" NG FROM BELOW

1-1/4" NG

2" NG

2" NG

16'12'8'4'0

SCALE: 3/16" = 1'-0"

M1.1

MECHANICAL FLOOR PLAN

1. PROVIDE IAP FA-0507-H HANGING FUME ARM IN-ROOM.

FIELD-COORDINATE ROUTING OF 5"Ø ROUND DUCTWORK THROUGH

EXISTING WALL OPENING INTO ROOM. ARM SHALL BE BALANCED TO

600CFM. SEE DETAILS 1 & 2 ON M0.2 FOR MORE INFORMATION.

2. PROVIDE CONCRETE PAD 6" MINIMUM AROUND PERIMETER OF

MECHANICAL EQUIPMENT. INSTALL UNIT ON FACTORY PROVIDED

EQUIPMENT RAILS. SEE DETAIL.

3. SUPPORT EXTERIOR DUCTWORK WITH MIRO INDUSTRIES DS-6 OR

APPROVED EQUAL. SEE DETAIL.

4. INSTALL FAN ON FACTORY PROVIDED EQUIPMENT RAIL WITH

VIBRATION ISOLATORS. SEE DETAIL.

KEY NOTES:

M1.1

MECHANICAL

FLOOR PLAN

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

16'12'8'4'0

SCALE: 3/16" = 1'-0"

M1.1

MECHANICAL ROOF PLAN

1. CONTRACTOR TO VERIFY NATURAL GAS PRESSURE ON-SITE AND

PROVIDE GAS PRESSURE REDUCERS AS REQUIRED.

GENERAL NOTES: #

CM MR

5. BURIED NATURAL GAS PIPING TO BE ROUTED FROM GAS METER AT

COMPLEX EXTERIOR. SEE LOCATION INDICATED ON G0.1 SITE PLAN

FOR APPROXIMATE LOCATION. PIPING SHALL BE BURIED BETWEEN

EXISTING GAS METER AND WELDING SHOP OUTSIDE THE FENCED

PERIMETER. APPROX. 175' TOTAL PIPING LENGTH FROM METER

SHOP TO EXISTING NATURAL GAS CONNECTION. VERIFY ROUTING

IN-FIELD.

6. SEE ARCHITECTURAL PLANS FOR WINDOW PENETRATION DETAIL

7. PROVIDE SUPPORTS FOR ROOFTOP GAS PIPING PER

SPECIFICATIONS.

1 11/14/2024 ADDENDUM 1

A-1

WIRING DEVICE SYMBOL LEGEND

SYMBOL DESCRIPTION

HOMERUN TO LIGHTING/SERVICE PANEL. HOMERUN INDICATES PANEL NAME AND

CIRCUIT NUMBER OR FEEDER TAG. CONDUCTORS SHALL BE #12 AWG IN 3/4” CONDUIT

(1” UNDERGROUND) UNLESS NOTED OTHERWISE. HOMERUNS MAY BE COMBINED INTO

A COMMON RACEWAY FOR 20A SINGLE PHASE CIRCUITS ONLY IF DEDICATED

NEUTRALS ARE USED OR HANDLE TIES ARE PROVIDED ON CIRCUIT BREAKERS TO

SIMULTANEOUSLY DISCONNECT ALL UNGROUNDED CONDUCTORS AT THE SAME TIME.

MAXIMUM OF (6) #12 AWG CURRENT CARRYING CONDUCTORS SHALL BE PROVIDED IN

RACEWAY. COMPLY WITH NEC FOR CONDUCTOR DERATING AND CONDUIT FILL..

CONDUIT STUB

CONDUIT TURNED DOWN

CONDUIT TURNED UP

CONDUIT INSTALLED BELOW GRADE OR BELOW FINISHED FLOOR

ELECTRICAL CONNECTION TO EQUIPMENT ITEM 'E101' (LETTER DESIGNATION

AS APPLICABLE) - SEE CORRESPONDING EQUIPMENT CONNECTION SCHEDULE

SPECIAL PURPOSE RECEPTACLE - HEIGHT AND TYPE AS NOTED ON DRAWINGS

SURFACE RACEWAY

JUNCTION BOX - MOUNTING HEIGHT AND SIZE AS REQUIRED BY CODE OR AS NOTED ON

DRAWINGS

JUNCTION BOX - FLOOR MOUNTED. SIZE AS REQUIRED BY CODE OR AS NOTED ON

DRAWINGS

VERTICAL SERVICE POLE

COMBINATION IN FLOOR POWER / DATA / A/V DEVICE.

PUSHBUTTON

FIRE ALARM SYMBOL LEGEND

SYMBOL DESCRIPTION

FIRE ALARM ANNUNCIATOR PANEL - WALL MOUNTED AT 60" AFF TO CENTER, UNO

FIRE ALARM CONTROL PANEL - WALL MOUNTED AT 72" AFF TO TOP, UNO

FIRE ALARM PULL STATION AT 44" AFF. UNO

MOTOR. SEE DRAWINGS FOR DESCRIPTION

COMBNATION MOTOR STARTER

MOTOR STARTER

DOOR BELL

30A/3P/20/1

FIRE ALARM VISUAL DEVICE. ROUGH-IN SUCH THAT BOTTOM OF LENS IS NO LESS THAN

80" AFF.

FIRE ALARM AUDIO/VISUAL DEVICE. ROUGH-IN SUCH THAT BOTTOM OF VISUAL LENS IS

NO LESS THAN 80" AFF.

FIRE ALARM HORN AUDIO DEVICE. ROUGH-IN SUCH THAT BOTTOM OF DEVICE IS NO

LESS THAN 80"AFF

FIRE ALARM SMOKE DETECTOR - CEILING MOUNTED, UNO

FIRE ALARM SMOKE DUCT DETECTOR

REMOTE TEST STATION FOR FA DUCT DETECTOR

TAMPER SWITCH

FLOW SWITCH

HEAT DETECTOR

CO DETECTOR

MAGNETIC DOOR HOLDER, AT 72" AFF UNO

DISTRIBUTION SYMBOL LEGEND

SYMBOL DESCRIPTION

ELECTRICAL PANEL, SURFACE MOUNTED.

ELECTRICAL PANEL, FLUSH MOUNTED.

TRANSFORMER

AUTOMATIC TRANSFER SWITCHATS

T1

LIGHTING & CONTROL SYMBOL LEGEND

SYMBOL DESCRIPTION

LIGHTING CONTROL OCCUPANCY SENSOR - CEILING MOUNTED

LIGHTING CONTROL PHOTOCELL

INTERIOR LIGHT FIXTURES AS SPECIFIED ON THE LIGHT FIXTURE SCHEDULE.

REFER ALSO TO LIGHTING CIRCUITING GUIDE.

LIGHT FIXTURE, HALF SHADING INDICATES EMERGENCY BACKUP. "NL" INDICATES 24/7

OPERATION (UNSWITCHED).

TECHNOLOGY SYMBOL LEGEND

SYMBOL DESCRIPTION

VOICE / DATA ROUGH-IN BOX, AT 18" AFF UNO. PROVIDE WITH 3/4" CONDUIT WITH PULL

STRING TO ABOVE CEILING, 6" BUSH END.

EMERGENCY LIGHTING FIXTURE, WITH BATTERY. REFER TO LIGHT FIXTURE SCHEDULE

EXTERIOR LIGHT FIXTURES AS SPECIFIED ON THE LIGHT FIXTURE SCHEDULE.

REFER ALSO TO LIGHTING CIRCUITING GUIDE.

EXIT SIGN. ARROW INDICATES ILLUMINATED DIRECTIONAL ARROWS, SHADED SECTION

INDICATES FACE WHICH IS ILLUMINATED.

VOICE / DATA ROUGH-IN BOX, FLOOR-MOUNTED. PROVIDE WITH 3/4" CONDUIT WITH PULL

STRING TO ABOVE CEILING, 6" BUSH END.

ABBREVIATIONS

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINSHED GRADE

ACH ABOVE COUNTER HEIGHT

AL ALUMINUM

BKR BREAKER

CU COPPER

CKT CIRCUIT

DWG DRAWING

EC EMPTY CONDUIT

EF EXHAUST FAN

EWC ELECTRIC WATER COOLER

FLA FULL LOAD AMPS

FU FUSE

FWE FURNISHED WITH EQUIPMENT

GC GENERAL CONTRACTOR

GFI/GFCI GROUND FAULT INTERRUPTER DEVICE

HPS HIGH PRESSURE SODIUM

IG ISOLATED GROUND

LRA LOCKED ROTOR AMPS

LTG LIGHTING(L)

MCA MINIMUM CIRCUIT AMPACITY

MCB MAIN CIRCUIT BREAKER

MCC MOTOR CONTROL CENTER

MDP MAIN DISTRIBUTION PANEL

MFR MANUFACTURER

MH METAL HALIDE

MLO MAIN LUG ONLY

MOCP MAXIMUM OVERCURRENT CIRCUIT PROTECTION

MSB MAIN SWITCHBOARD

NL NIGHT LIGHT

NIC NOT IN CONTRACT

NTS NOT TO SCALE

PH PHASE

PNL PANEL

RCPT RECEPTACLE

REQD REQUIRED

RTU ROOFTOP UNIT

SP SURGE PROTECTED DEVICE

SW SWITCH

UGND UNDERGROUND

UH UNIT HEATER

UNO UNLESS NOTED OTHERWISE

W/ WITH

WH WATER HEATER

WP WEATHER PROOF

XFMR TRANSFORMER

SECURITY CAMERA. COORDINATE REQUIREMENTS WITH OWNER.

WIRELESS ACCESS POINT. COORDINATE REQUIREMENTS WITH OWNER.

NL

DAYLIGHT SENSOR

LIGHTING CIRCUITING GUIDE

SYMBOL DESCRIPTION

B / X-1 LIGHTING TYPE AND CIRCUIT DESIGNATION

X: REFER TO PANEL SCHEDULE, PER DRAWING

1: CIRCUIT NUMBER

B: LIGHT FIXTURE TYPE, REFER TO LIGHT FIXTURE SCHEDULE(a)

SWITCHING SCHEME OR ZONE

POWER CIRCUITING GUIDE

SYMBOL DESCRIPTION

X-1 POWER CIRCUITING DESIGNATION

X: REFER TO PANEL SCHEDULE, PER DRAWING

1: CIRCUIT NUMBER

DEVICE, JUNCTION BOX, FLOOR BOX, ETC

XXX

EQUIPMENT ABBREVIATION, REFER TO LEGEND AND

ABBREVIATION SCHEDULE FOR ADDITIONAL INFORMATION

TELEVISION OUTLET. SINGLE GANG BOX WITH SINGLE GANG PLASTER RING. PROVIDE

WITH 3/4" CONDUIT WITH PULL STRING TO ABOVE CEILING, 6" BUSH END. PROVIDE WITH

ADJACENT DUPLEX RECEPTACLE

E101

J

J

F

F

F

F

FACP

FAAP

DD

RTS

TS

HD

CO

FS

D

PC

OS

DS

TV

SC

AP

B

SAFETY DISCONNECT SWITCH. "30" INDICATES AMP RATING, "3P" INDICATES NUMBER OF

POLES, "20" INDICATES FUSE SIZE, "1" INDICATES NEMA ENCLOSURE RATING (1, 3R, 4X,

ETC). HEAVY DUTY SAFETY SWITCH UNLESS NOTED OTHERWISE. "NF" INDICATES

NON-FUSED.

SCCR SHORT CIRCUIT CURRENT RATING

FOR RECEPTACLES ABOVE, SUBSCRIPT DEFINITION AS FOLLOWS:

GFI - GROUND FAULT DEVICE

IG - ISOLATED GROUND

USB - DEVICE WITH USB PORT

WP - WEATHERPROOF

CR - CORD REEL

DUPLEX RECEPTACLE AT 18" AFF, UNO. NEMA 5-20R.

QUADRUPLEX RECEPTACLE AT 18" AFF, UNO. NEMA 5-20R.

DUPLEX RECEPTACLE - CEILING MOUNTED. NEMA 5-20R.

DUPLEX RECEPTACLE - FLOOR MOUNTED. NEMA 5-20R.

SINGLE RECEPTACLE AT 18" AFF, UNO. NEMA 5-20R.

C - MOUNTED 8" ABOVE COUNTER

H - MOUNTED HORIZONTALLY

20A SWITCH AT 44" CL AFF, UNO

FOR SWITCH OR DIMMER ABOVE, SUBSCRIPT DEFINITION AS FOLLOWS:

a,b - SWITCHING SCHEME m - MOTOR RATED

P - PILOT LIGHT

3 - 3-WAY SWITCH

4 - 4-WAY SWITCH

o - OCCUPANCY SENSOR v - VACANCY SENSOR

S

D WALL DIMMERx x

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

ELECTRICAL

SCHEDULES &

DETAILS

LJK TPW

E0.1

SYMBOL:

EXIT SIGN

LIGHTING SWITCH

FINISHED FLOOR 1'-4" UNO

SYMBOL:

SYMBOL:

TELEPHONE OR

TOP OF

DATA

SYMBOL ,

44" UNO

6"

MAX.

SYMBOL:

SYMBOL:

6' -8

" U N

O

ACTIVATION

HANDLE

F

F

EXIT

4'-0"

MAX.

NOT TO SCALE

E0.1

TYPICAL DEVICE MOUNTING DETAIL

FIRE ALARM

HORN / STROBE

FIRE ALARM

MANUAL PULL

STATION

120V CONVENIENCE

RECEPTACLE

1P 20A

120VAC

(M-14)

LC3

TO EF-2

LC1

M-1

M-3

TO EF-1

M-5

TO EF-1

TO EF-1

NOTES:

1. HVAC CONTROLLER SHALL BE IN A NEMA TYPE 1 ENCLOSURE SIZED AS REQUIRED. PROVIDE ENGRAVED NAMEPLATE ON

DOOR LABELED AS "HVAC CONTROLS".

2. CONTACTOR SHALL BE SQUARE D CLASS 8903 ELECTRICALLY HELD CONTACTOR OR APPROVED EQUAL. CONTACTS SHALL

BE 30A OR 60A CONTINUOUS RATED AS INDICATED. PROVIDE COIL VOLTAGE AS INDICATED.

NOT TO SCALE

E0.1

HVAC CONTROL WIRING DIAGRAM

GENERAL NOTES:

CONTRACTOR IS RESPONSIBLE TO REVIEW AND UNDERSTAND ALL DRAWINGS

SPECIFICATIONS AND ALL WORK OF ALL TRADES TO ENSURE A COMPLETE AND THOROUGH

PROJECT. CONTRACTOR SHALL COOPERATE AND COORDINATE ALL PHASES OF WORK WITH

OTHER DISCIPLINES AND GENERAL CONTRACTOR.

THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS AND CLEARANCES PRIOR TO

INSTALLATION OF EQUIPMENT AND RACEWAYS.

CONTRACTOR SHALL OBTAIN ALL PERMITS AND COORDINATE ALL INSPECTIONS REQUIRED BY

LOCAL AUTHORIZED AGENCIES HAVING JURISDICTION. PERMIT/INSPECTION FEES SHALL BE

THE RESPONSIBILITY OF THE CONTRACTOR.

ALL WORK SHALL BE EXECUTED IN ACCORDANCE WITH RECOGNIZED STANDARDS OF

WORKMANSHIP. ALL WORK SHALL BE INSTALLED IN A NEAT AND ORDERLY MANNER.

ALL ELECTRICAL CONSTRUCTION SHALL CONFORM TO THE NATIONAL ELECTRICAL CODE, NC

DOA STATE CONSTRUCTION MANUAL APPLICABLE NEMA, ANSI, AND IEEE PUBLICATIONS, U.L.

STANDARDS, AND OSHA REQUIREMENTS. WORK SHALL COMPLY WITH LOCAL, COUNTY, STATE,

AND NATIONAL CODES HAVING JURISDICTION.

PROVIDE MATERIALS AND LABOR FOR A COMPLETE ELECTRICAL INSTALLATION. ALL

ELECTRICAL MATERIALS, DEVICES, APPLIANCES, AND EQUIPMENT SHALL BE NEW AND BEAR

THE UNDERWRITERS LABORATORIES, INC. (UL) LABEL WHERE AVAILABLE.

ALL EQUIPMENT, FIXTURES, DEVICES, AND MATERIALS SHALL BE FREE OF CORROSION, DIRT, PAINT, SPLATTER OR DAMAGE OF ANY SORT AT FINAL ACCEPTANCE OF THE WORK.

ELECTRICAL CONTRACTOR SHALL CLEAN, REPAIR OR REPLACE SAME AS INSTRUCTED BY

OWNER BEFORE FINAL PAYMENT.

TO EF-2

TO EF-2

M-7

M-9

M-11

LC4

TO MAU-2

LC2

M-2

M-4

TO MAU-1

M-6

TO MAU-1

TO MAU-1

TO MAU-2

TO MAU-2

M-8

M-10

M-12

NEMA 1 CONTACTOR ENCLOSURE

60A 30A

60A 30A

1 11/14/2024 ADDENDUM 1

1 1

1 1

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

ELECTRICAL

PANEL SCHEDULES

LJK TPW

E0.2

A. EXISTING CIRCUIT DATA SHOWN IS TAKEN FROM EXISTING FACILITY

DRAWINGS AND/OR FIELD OBSERVATION. FIELD VERIFY ALL CIRCUITS.

B. REFER TO LEGEND, RISER DIAGRAM, AND PLANS FOR ADDITIONAL

INFORMATION.

C. VERIFY ALL CIRCUITS ON EXISTING PANELS. ADJUST CIRCUITING AS

REQUIRED TO MEET DESIGN INTENT OF DRAWINGS. FOR ANY VACATED

CIRCUITS, REMOVE CONDUIT AND WIRING BACK TO PANEL, TURN BREAKER

OFF, AND MARK BREAKER AS 'SPARE'. FOR EXISTING CIRCUITS MISLABELED

BUT CONNECTED TO EXISTING LOAD REQUIRED TO REMAIN, FIELD

DETERMINE LOAD AND PROVIDE APPROPRIATE DESCRIPTION IN PANEL

DIRECTORY.

D. PROVIDE NEW TYPEWRITTEN PANEL DIRECTORY TO REFLECT NEW

CONDITIONS UPON COMPLETION OF WORK DESCRIBED IN THESE DRAWINGS.

E. REUSE EXISTING CIRCUIT BREAKERS WHERE POSSIBLE. PROVIDE NEW

BREAKERS AS REQUIRED, TYPE, VOLTAGE RATING, AND AIC RATING TO

MATCH EXISTING.

F. REPAIR OR REPLACE ANY MISSING OR DAMAGED COMPONENTS ON EXISTING

PANELBOARDS; FIELD VERIFY EXACT REQUIREMENTS.

G. PROVIDE LISTED HANDLE TIES FOR ALL BREAKERS SERVING MULTIWIRE

BRANCH CIRCUITS, I.E., SEPARATE BRANCH CIRCUITS THAT SHARE THE

NEUTRAL CONDUCTOR IN ACCORDANCE WITH NEC 210.4.

GENERAL NOTES - PANEL SCHEDULES:

1 11/14/2024 ADDENDUM 1

EXISTING PEAK DEMAND PER NEC 220.87

= 16.8 KW

ASSUME 0.8 POWER FACTOR

= 21 KVA

125% DEMAND FACTOR

= 26.25 KVA

NEW LOAD FROM PANEL 'A'

= 11.7 KVA

NEW LOAD FROM PANEL 'M'

= 49.9 KVA

NEW HVAC OAU-1

= 29.4 KVA

TOTALS:

26.25 + 11.7 + 49.9 + 29.4

= 117.25 KVA

= 325.5 A

LOAD ANALYSIS

FINISHED FLOOR

EXISTING

PANEL

'DP'

600A

208Y/120V 3P, 4W

MCB

EXISTING

PANEL

'W1' 225A

208Y/120V 3P, 4W

MLO

EXISTING

PANEL

'W2' 225A

208Y/120V 3P, 4W

MLO

EXISTING

PANEL

'W3' 225A

208Y/120V 3P, 4W

MLO

FINISHED GRADE

COORDINATE INTERRUPTION OF EXISTING ELECTRICAL SERVICE WITH OWNER AND

CONSTRUCTION MANAGER NO FEWER THAN 5 WORKING DAYS IN ADVANCE OF PROPOSED

INTERRUPTION. MINIMIZE THE EXTENT OF THE DOWNTIME AS MUCH AS POSSIBLE BY

FULLY INSTALLING REQUIRED COMPONENTS AHEAD OF TIME TO THE EXTENT POSSIBLE.

EXISTING SERVICE GROUND

EXISTING

PANEL

'W4' 225A

208Y/120V 3P, 4W

MLO

EXISTING

PANEL

150A 208Y/120V

3P, 4W

MCB

TO FEEDER PANEL

IN MAIN ADMIN

BUILDING

CT

CABINET

TO

POLE-MOUNTED

UTILITY

TRANSFORMER

EXISTING

UTILITY

METER 1

(TYP)

ALTERNATE #2

FINISHED FLOOR

EXISTING

PANEL

'DP'

600A

208Y/120V 3P, 4W

MCB

EXISTING

PANEL

'W1' 225A

208Y/120V 3P, 4W

MLO

EXISTING

PANEL

'W2' 225A

208Y/120V 3P, 4W

MLO

EXISTING

PANEL

'W3' 225A

208Y/120V 3P, 4W

MLO

FINISHED GRADE

COORDINATE INTERRUPTION OF EXISTING ELECTRICAL SERVICE WITH OWNER AND

CONSTRUCTION MANAGER NO FEWER THAN 5 WORKING DAYS IN ADVANCE OF PROPOSED

INTERRUPTION. MINIMIZE THE EXTENT OF THE DOWNTIME AS MUCH AS POSSIBLE BY

FULLY INSTALLING REQUIRED COMPONENTS AHEAD OF TIME TO THE EXTENT POSSIBLE.

EXISTING

PANEL

'W4' 225A

208Y/120V 3P, 4W

MLO

NEW

PANEL

'A' 125A

208Y/120V 3P, 4W

MLO

CT

CABINET

EXISTING

UTILITY

METER

(TYP)

ALTERNATE #2

NEW

PANEL

'M' 225A

208Y/120V 3P, 4W

MLO

EXISTING SERVICE GROUND

TO

POLE-MOUNTED

UTILITY

TRANSFORMER

RISER KEY NOTES:

1. ALL EQUIPMENT SHOWN IS EXISTING U.N.O. AS "NEW".

2. EXISTING CONDUCTORS SHALL BE REMOVED. EXISTING CONDUIT SHALL

BE CUT FLUSH AND CAPPED. EXISTING FEEDER BREAKER SHALL BE

SWITCHED OFF AND MARKED AS SPARE.

3. NEW PANEL TO REPLACED EXISTING. RECONNECT EXISTING BRANCH

CIRCUITS.

WIRING SCHEDULE:

4 #1, 1 #6 GND; 2"C

4 #3/0, 1 #6 GND; 2-1/2"C

GENERAL NOTES:

A. ALL DISTRIBUTION EQUIPMENT AND FEEDERS ARE EXISTING TO REMAIN

AS IS UNLESS NOTED OTHERWISE. EQUIPMENT AS NOTED IS TAKEN

FROM EXISTING FACILITY DRAWINGS. FIELD VERIFY ALL EXISTING

EQUIPMENT AND FEEDER TYPES, RATINGS, SIZES, CONFIGURATIONS,

AND LOCATIONS.

B. FIELD VERIFY AND COORDINATE EXACT EQUIPMENT ARRANGEMENT,

LOCATIONS, CONDUIT ROUTING AND REQUIREMENTS PRIOR TO WORK.

C. NOTIFY ENGINEER IMMEDIATELY OF EXISTING CONDITIONS ARE

DIFFERENT THAN SHOWN.

ALTERNATE NOTES:

1. ALTERNATE #2 SCOPE IS TO REPLACE EXISTING FEDERAL PACIFIC

PANELBOARD WITH NEW PANEL A AND RECONNECT EXISTING BRANCH

CIRCUITS. PROVIDE NEW FEEDER TO NEW DISTRIBUTION PANEL.

2. ALTERNATE #2 IS MANDATORY WORK, BUT SHALL BE PRICED

SEPARATELY FROM BASE BID.

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

ELECTRICAL

SINGLE LINE

DIAGRAMS

LJK TPW

E0.3

NOT TO SCALE

E0.3

EXISTING SINGLE LINE DIAGRAM

NOT TO SCALE

E0.3

NEW SINGLE LINE DIAGRAM

1 11/14/2024 ADDENDUM 1

MECH, ROOM

SERVICE CORRIDORTOILET

LAVATORY

SHOWER

MOP

ROOM TOILET TOILET

LOCKED

ROOMS

PANEL 'W1'

PANEL 'W2'

PANEL 'DP'

PANEL 'W3'

PANEL 'W4'

CT CABINET

PANEL 'A'

METER

MAU-1

MAU-2

OAU-1

WP/GFI

A-24

WP/GFI

A-24

WP/GFI

A-24

SS

PANEL 'M'

EF-2EF-1

DRAWING NO.

DRAWING NAME

SEALS

Drawn By: Checked By:

REVISIONS

NO. DATE DESCRIPTION

PROJECT INFORMATION:

CONSULTANT

PROJECT NUMBER:

DISCLAIMER: THIS DOCUMENT IS THE

PROPERTY OF DEVITA & ASSOCIATES, INC.

AND IS FURNISHED WITH THE CONDITION

THAT IT IS NOT TO BE CHANGED WITHOUT

THE WRITTEN AUTHORIZATION OF DEVITA

& ASSOCIATES, INC. FURTHERMORE, THIS

DOCUMENT IS NOT TO BE COPIED,

REPRODUCED OR USED BY OTHERS EXCEPT

AS REQUIRED FOR THE WORK OF THIS

SPECIFIC PROJECT.

www.devitainc.com

877.4.DEVITA

corp@devitainc.com

NC Firm License No. C-0819

ATLANTA | CHARLOTTE | GREENVILLE | RICHMOND

DeVita & Associates, Inc. Project : 24529

ISSUED: 10/29/2024

Cleveland Community College Welding Shop Corrections Facility 260 Kemper Rd. Shelby, NC 28152

24529

CLEVELAND

COMMUNITY

COLLEGE

WELDING SHOP

CORRECTIONS

FACILITY

260 KEMPER RD

SHELBY, NC 28252

1. NEW PANELBOARD TO REPLACE EXISTING AS

PART OF ALTERNATE #2.

2. HVAC CONTACTOR ENCLOSURE. REFER TO

DETAIL 2/E0.1.

3. SWITCH LOCATION FOR CONTROL OF EXHAUST

FANS AND MAKEUP AIR UNITS. REFER TO DETAIL

2/E0.1. LABEL AS "FAN CONTROLS".

KEY NOTES:

ELECTRICAL

PLANS

LJK TPW

E1.116'12'8'4'0

SCALE: 3/16" = 1'-0"

E1.1

ELECTRICAL FLOOR PLAN

16'12'8'4'0

SCALE: 3/16" = 1'-0"

E1.1

ELECTRICAL ROOF PLAN

1 11/14/2024 ADDENDUM 1