C05_Salient_Characteristics.pdf

Salient Characteristics

Car Wash Replacement

Hot Water Pressure Washer System

1.0 Motor

1.0 National Electrical Manufacturers Association (NEMA) nominal efficiency rating of

93.6%.

1.1 15 horsepower - 460 Volt three (3) phase; max current used: 38.0 Amps @ 460

Volts.

1.2 Number of poles – four (4); frame – 286T; service factor 1.15; Revolutions per minute (RPM) – 1760

2.0 Pump

2.0 Gallons per minute (GPM) - 6.0; Pounds per Square Inch (PSI) minimum – 3,000; Die-cast body; Forged brass head; sight glass rear and side covers; solid ceramic plungers; anodized cooling fins

2.1 Must come with:

2.1.1 Safety relief valve

2.1.2 Minimum 36’ (thirty-six-feet) power cord 6 (six) American Wire Gauge

(AWG)/4 wire Ampacity 50 Amps

2.1.3 Easy start feature – feature to eliminate static back pressure

2.1.4 Two (2) hose assemblies with quick connects – 3/8” (three-eighth of an inch) x 100 feet/7200 PSI; National Pipe thread male rigid (MP) x hose to pipe National Pipe Thread swivel (MPX) fittings

2.1.5 Foot valve (21 GPM@7250PSI) Inlet ½” (one-half of an inch) Female

National Pipe Thread (FNPT)

2.1.6 Six (6) high pressure couplers 6FP (Female rigid national pipe thread) x

6FP (Female rigid national pipe thread) fittings

2.1.7 High Pressure reducer hex nipple 8MP (national pipe thread male rigid) x

4MP (national pipe thread male rigid)

2.1.8 High Pressure hex bushing 8MP (national pipe thread male rigid) x 6FP

(female rigid national pipe thread

2.1.9 Plug ¼” (one quarter of an inch) female high pressure

2.1.10 Socket 3/8” male high pressure

2.1.11 One (1) two-hundred-foot (200’) three-eighth inch (3/8”) hose braid wire thermos 180 degrees Fahrenheit Black/Blue – 8,000 PSI 3/8” MP (national pipe thread male ridged) both ends one swivel MPS (national pipe thread male swivel)

2.1.12 Minimum fifty-foot (50’) hose, trigger gun, wand, quick connect nozzles, safety coupler

2.1.13 Minimum two (2) year manufacturers warranty for parts and labor.

2.1.14 Stationary LP gas fired hot water pressure washer to provide water temperatures between 180-200 degrees Fahrenheit. It shall be cabinet style with cleaning power of 6 GPM @ 3,000 psi. Standard accessories shall ship with the machine.

Water Recycle System

1.0 The water recycle system shall be fully automatic with electric control panel that indicates operation status with lighted switches on a NEMA 4 rated enclosure with a 10 ‘ GFCI Cord.

2.0 It shall have a self-priming recycle feed pump controlled by a float switch in collection pit and an inlet strainer with stainless steel screen in a corrosion resistant plastic housing.

3.0 It shall have electronic controlled metering pumps which introduce additives into the waste stream.

Bleed valves shall be used for pump priming.

4.0 A discharge pump shall provide pressure feed to pressure washer. Final filters shall polish the water just prior to being used for washing.

5.0 The base assembly shall be hot dipped galvanized steel. It shall have a coagulant compartment shall allow additives to react with the pollutants in the wastewater.

6.0 A separator compartment shall allow clean, clear water to separate from the contaminants and a storage compartment shall hold treated water until it is needed for washing.

7.0 A polypropylene tank shall be unitized construction and schedule 80 PVC pipe shall be used throughout.

8.0 Finally, filter socks shall collect pollutants for disposal.