Att 16 - DAS -Temporary Inside Signage 1.docx
DOCX document 18 KB Posted
- Attached to
- Z1DZ--Project #629-18-114 Expand Distributed Antenna System (DB) Federal contract opportunity
- Solicitation number
- 36C25624R0010
About this file
This document is a technical specification for Temporary Interior Signage. It describes the requirements for fabricating and installing temporary interior signs, including the material, size, reinforcement, and attachment method. The key details are:
The signs must be fabricated from 50 Kg (110 pound) mat finish white paper, cut to 100 mm (4-inch) wide by 300 mm (12 inch) long, with a 3 mm (1/8-inch) diameter hole punched and reinforced on both sides. Steel wire 0.3 mm (0.0120-inch) thick ties are to be used to attach the signs to room door frames or knobs/levers. The signs must be marked with felt tip markers to clearly identify room numbers as designated on the floor plans. The specification outlines where the signs should and should not be installed, and requires replacing any missing, damaged, or illegible signs.
This technical specification is related to Federal Contract Opportunity f6d17e1febe84ddc8b1e891966b3ee93, Solicitation Number 36C25624R0010 issued by the Department of Veterans Affairs Veterans Health Administration Veterans Integrated Service Network 16 for the Expand Distributed Antenna System project.
View the file
Other files for this federal contract opportunity
Show all 50
Z1DZ--Project #629-18-114 Expand Distributed Antenna System (DB) has more files on GovTribe.
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
07-01-15
SECTION 01 58 16
TEMPORARY INTERIOR SIGNAGE
PART 1 GENERAL
DESCRIPTION
This section specifies temporary interior signs.
PART 2 PRODUCTS
2.1 TEMPORARY SIGNS
| A. | Fabricate from 50 Kg (110 pound) mat finish white paper. |
| B. | Cut to 100 mm (4-inch) wide by 300 mm (12 inch) long size tag. |
| C. | Punch 3 mm (1/8-inch) diameter hole centered on 100 mm (4-inch) dimension of tag. Edge of Hole spaced approximately 13 mm (1/2-inch) from one end on tag. |
| D. | Reinforce hole on both sides with gummed cloth washer or other suitable material capable of preventing tie pulling through paper edge. |
| E. | Ties: Steel wire 0.3 mm (0.0120-inch) thick, attach to tag with twist tie, leaving 150 mm (6-inch) long free ends. |
PART 3 EXECUTION
3.1 INSTALLATION
| A. | Install temporary signs attached to room door frame or room door knob, lever, or pull for doors on corridor openings. |
| B. | Mark on signs with felt tip marker having approximately 3 mm (1/8-inch) wide stroke for clearly legible numbers or letters. |
| C. | Identify room with numbers as designated on floor plans. |
3.2 LOCATION
| A. | Install on doors that have room, corridor, and space numbers shown. |
| B. | Doors that do not require signs are as follows: |
| 1. | Corridor barrier doors (cross-corridor) in corridor with same number. |
| 2. | Folding doors or partitions. |
| 3. | Toilet or bathroom doors within and between rooms. |
| 4. | Communicating doors in partitions between rooms with corridor entrance doors. |
| 5. | Closet doors within rooms. |
| C. | Replace missing, damaged, or illegible signs. |
- - - E N D - - - 01 58 16 - 1
File details come from the government source that posted it. Updated .