Specification REV-1 - 04 November 2022.pdf

USCGC KIMBALL (WMSL 756)

SPECIFICATION FOR DRYDOCK REPAIRS

FY2023

Developed By: Daniel A Doherty

(Rev-1, 4 November 2022)

USCGC KIMBALL (WMSL-418) DRYDOCK AVAILABILITY FY2023

ii (Rev-1)

TABLE OF CONTENTS

Revisions Record .......................................................................................................................................... iv Consolidated List of References .................................................................................................................... v Consolidated List of Government-furnished Property ................................................................................ xv Consolidated List of Critical Inspection Items ........................................................................................ xxiii Principal Characteristics ........................................................................................................................... xxiv General Requirements WORK ITEM 1: Hull 3D, Laser Scan WORK ITEM 2: Hull Plates (Freeboard), Inspect WORK ITEM 3: Hull Plates (U/W Body), Inspect WORK ITEM 4: Freeboard, Preserve (Full) WORK ITEM 5: Superstructure, Preserve (Partial) WORK ITEM 6: U/W Body Hull, Preserve (Full) WORK ITEM 7: Tenting, Provide WORK ITEM 8: Tenting (Mast), Provide WORK ITEM 9: Propulsion Shaft Fairwaters And Rope Guards, Inspect WORK ITEM 10: Chain Lockers and Sump, Preserve WORK ITEM 11: Chain Lockers and Sump, Clean and Inspect WORK ITEM 12: Voids (Non-Accessible), Preserve WORK ITEM 13: Voids (Non-Accessible), Leak Test WORK ITEM 14: Sideport Shell Door, Level 2, Inspect WORK ITEM 15: Mast, Preserve WORK ITEM 16: Propulsion Shaft Alignment & Bearings (External) Clearances, Check WORK ITEM 17: Propulsion Shaft Coverings (MIL-STD-2199B), Inspect and Repair WORK ITEM 18: Propulsion Shaft Seals (Mechanical), Overhaul WORK ITEM 19: Controllable Pitch Propeller Hub Assembly, General Maintenance WORK ITEM 20: Controllable Pitch Propeller System, Perform General Maintenance WORK ITEM 21: Doppler Speed Log Valve, Overhaul WORK ITEM 22: Doppler Speed Log, General Maintenance WORK ITEM 23: Fathometer Transducer (Deep Water), General Maintenance WORK ITEM 24: Shallow Water Transducer, Renew WORK ITEM 25: Sea Valves and Waster Pieces, Overhaul Or Renew WORK ITEM 26: Seawater Strainers (All Sizes), Overhaul and Inspect WORK ITEM 27: Rudder Stock Bearings, Check Clearances WORK ITEM 28: Rudder Stock Seals, Overhaul WORK ITEM 29: Steering System, Inspect and Service WORK ITEM 30: Bow Thruster Unit (General), Overhaul WORK ITEM 31: Anchors Chains and Ground Tackles, Inspect and Preserve WORK ITEM 32: Impressed Current Cathodic Protection System Dielectric Shield (Capastic Fairing), Renew WORK ITEM 33: Impressed Current Cathodic Protection System, Inspect and Maintain WORK ITEM 34: Cathodic Protection (Zincs), Renew WORK ITEM 35: Impressed Current Cathodic Protection System Anodes, Renew WORK ITEM 36: Impressed Current Cathodic Protection System Reference Cells, Renew WORK ITEM 37: Ship Service Diesel Generator (No. 3) Exhaust Piping, Modify WORK ITEM 38: Transom Double Doors and Tow Outfits, Modify WORK ITEM 39: Stern Door Hydraulic and Control System, Modify WORK ITEM 40: Stern Ramp Rails, Modify WORK ITEM 41: Cascade Orificial Resistive Device, Clean And Inspect iii (Rev-1)

WORK ITEM 42: Deck Covering (Slip-Resistant) Mast, Preserve WORK ITEM 43: Drydocking, Accomplish WORK ITEM 44: Vessel in Drydock Temporary Services, Provide WORK ITEM 45: Sea Trial Performance, Support, Provide iv (Rev-1)

REVISIONS RECORD

This page is used to record specification revisions, which may have occurred subsequent to a Revision 0 (Rev-0) package. Information listed is intended to provide contractors and field unit personnel a means to ensure all the current specification revision pages are present when reviewing or utilizing this specification package.

DATE REV# WORK

ITEM#

CHANGES MADE

04NOV22 1 Multiple Updated Consolidated List of Government-Furnished Property and GFE Tables for multiple work items.

NOTE : All work item and paragraph numbers listed above for a given revision correspond to same numbers in the previous revision. This revised specification is self-contained with all of the above listed changes incorporated.

v (Rev-1)

CONSOLIDATED LIST OF REFERENCES

The below-listed documents form a part of this specification to the extent specified herein. Approval/publication dates or revision dates/numbers are also identified, to ensure that same document versions are used at the time of specification writing and during contract execution.

All Coast guard drawings, technical publications, and standard specifications will be provided to contractors by the Coast Guard at an appropriate time, or upon request, free of charge. Other Government documents may be accessed – free of charge – from links located on the SFLC website. Commercial sites provide access to their respective documents.

COAST GUARD DRAWINGS

Coast Guard Drawing 418A-WMSL-100-001, Rev A, General Arrangements Coast Guard Drawing 418A-WMSL 100-006, Rev -, Inboard and Outboard Profiles Coast Guard Drawing 418A-WMSL 167-001, Rev A, Fabrication & Installation Transom Doors Coast Guard Drawing 418A-WMSL 169-001, Rev B, Stern Door Extension and Incidental Mods, Extension Panel Construction Coast Guard Drawing 418A-WMSL 186-001, Rev -, Tow Bitt Structural Reinforcement Coast Guard Drawing 418A-WMSL 801-001, Rev -, Booklet of General Plans Coast Guard Drawing 418A-WMSL-100-006, Rev -, Inboard and Outboard Profiles Coast Guard Drawing 418A-WMSL-101-005, Rev -, Shell Expansion Scantlings Coast Guard Drawing 418A-WMSL-114-001, Rev N-A, Fairwaters and Rope Guard Installation Details

& L/M Coast Guard Drawing 418A-WMSL-167-001, Rev A, Fabrication & Installation Transom Doors Coast Guard Drawing 418A-WMSL-169-001, Rev D, Stern Door Extension and Incidental Mods Coast Guard Drawing 418A-WMSL-186-001, Rev -, Tow Bitt Structural Reinforcement Coast Guard Drawing 418A-WMSL-264-001, Rev A, Rdcn Gr / CPP Gtrb LO Diagram Coast Guard Drawing 418A-WMSL-424-001, Rev B, Electronic Navigation Acoustical Cable Block

Diagram Coast Guard Drawing 418A-WMSL-521-001, Rev A, Firemain Diagram Coast Guard Drawing 418A-WMSL-556-001, Rev A, Stern Gate Hydraulic System Diagram Coast Guard Drawing 418A-WMSL-571-001, Rev -, FAS Arrangement Installation and Details Coast Guard Drawing 418A-WMSL-571-003, Rev -, FAS Arrangement Modification Coast Guard Drawing 418A-WMSL-593-002, Rev B, Sewage System Diagram Coast Guard Drawing 418A-WMSL-801-001, Rev A, Booklet of General Plans Coast Guard Drawing 750-WMSL-424-001, Rev D, Electronic Navigation Acoustical Cable Block

Diagram (ASC424001) Coast Guard Drawing 750 WMSL-167-001, Rev J, Manhole Installation and Fabrication Details Ship

Wide (ASC167001) Coast Guard Drawing 750 WMSL-264-002, Rev -, RDCN Gear / CPP and Gas Turbine Lube Oil System

Description (ASC264001-02) vi (Rev-1)

Coast Guard Drawing 750 WMSL-320-025, Rev D, Cathodic Protection System Deck Plan and Elementary Wiring Diagram (ASC320014)

Coast Guard Drawing 750-WMSL 100-042, Rev H, Unit 3230 Structure - 2nd Dk to Main Deck - Fr 76 to Fr 88 (ASC100323)

Coast Guard Drawing 750-WMSL 100-044, Rev K, Unit 3320 Struct - Inner Bottom 2nd Deck Fr 89-98

(ASC100332)

Coast Guard Drawing 750-WMSL 100-045, Rev K, 2nd Dk to Main Dk - Fr 82 to Aft (ASC100333) Coast Guard Drawing 750-WMSL 100-050, Rev K, Unit 4230 Structure - Mast (ASC100423) Coast Guard Drawing 750-WMSL 100-072, Rev -, Topside Configuration for NSC 5 & Follow

(AS5100004)

Coast Guard Drawing 750-WMSL 556-003, Rev E, Label Plate List - Blst/Deballast-Overfl/Ae/St-Hydr

Sys (ASC556002) Coast Guard Drawing 750-WMSL 582-001, Rev D, Anchoring, Mooring, and Towing Arrangement

(ASC582001)

Coast Guard Drawing 750-WMSL 582-002, Rev H, Mooring and Towing Arrangement (ASC582002) Coast Guard Drawing 750-WMSL 583-001, Rev C, Small Boat Handling Arrangements (ASC583001) Coast Guard Drawing 750-WMSL 583-521, Rev B, Boat Launch & Recovery Ramp Rail Modifications Coast Guard Drawing 750-WMSL 635-001, Rev -, Thermal & Acoustic Insulation (ASC635001) Coast Guard Drawing 750-WMSL 635-502, Rev -, Insulation Arr & Details Thermal, Acoustic, & Fire Coast Guard Drawing 750-WMSL 801-011, Rev -, Booklet of General Plans Coast Guard Drawing 750-WMSL 167-005, Rev C, Side Port Door Installation & Details (ASC167005) Coast Guard Drawing 750-WMSL-085-002, Rev C, Docking Drawing (AS1085007) Coast Guard Drawing 750-WMSL-085-014, Rev A, Tank Sounding and Moment of Inertia Tables

(WMSL-756 Only) (ASC085014G) Coast Guard Drawing 750-WMSL-085-016, Rev -, Tank Capacity Curves (ASC085013G) (756) Coast Guard Drawing 750-WMSL-085-040, Rev C, Docking Drawing (NSC 7 SRD) (ASC085007G) Coast Guard Drawing 750-WMSL-100-011, Rev H, Unit 1110 Structure - Inner Bottom, 1st Platf, & 2nd

Dk - Bow to Fr 10 (ASC100111) Coast Guard Drawing 750-WMSL-100-022, Rev K, Unit 2110 Structure - Innerbottom to 1st Platf Fr 35 -

44 (ASC100211)

Coast Guard Drawing 750-WMSL-100-027, Rev K, Unit 2210 Structure - Innerbottom to 1st Platform -

Fr 44 to Fr 52 (ASC100221) Coast Guard Drawing 750-WMSL-100-032, Rev K, Unit 2310 Structure - Innerbottom to 1st Platform -

Fr 52 to Fr 64 (ASC100231) Coast Guard Drawing 750-WMSL-100-036, Rev N, Unit 3110 Structure - 1st Platform and Below Fr 65-

77 (ASC100311)

Coast Guard Drawing 750-WMSL-100-040, Rev L, Unit 3210 Structure - Inner Bot to 1st Platform - Fr

76 to Fr 88 (ASC100321) Coast Guard Drawing 750-WMSL-100-041, Rev G, Unit 3220 Structure 1st Platform to 2nd Deck – Fr 76 to 88 (ASC100322) Coast Guard Drawing 750-WMSL-100-044, Rev K, Unit 3320 Struct - Inner Bottom 2nd Deck Fr 89-98

(ASC100332)

Coast Guard Drawing 750-WMSL-100-045, Rev J, 2nd Dk to Main Dk - FR 82 to Aft (ASC100333) vii (Rev-1)

Coast Guard Drawing 750-WMSL-100-046, Rev F, Unit 4110 - 01 Level to 02 Level - Fr 28 to Fr 33

(ASC100411)

Coast Guard Drawing 750-WMSL-100-047, Rev G, 02 Level to 03 Level Frame 28 to Frame 33

(ASC100412)

Coast Guard Drawing 750-WMSL-100-048, Rev H, Unit 4210 Structure - 01 Lvl to 02 Lvl - Fr 33 to Fr

44 (ASC100421)

Coast Guard Drawing 750-WMSL-100-049, Rev K, Unit 4220 Structure - 02 Lvl and Above - Fr 33 to Fr

44 (ASC100422)

Coast Guard Drawing 750-WMSL-100-050, Rev K, Unit 4230 Structure - Mast (ASC100423) Coast Guard Drawing 750-WMSL-100-053, Rev J, Unit 4420 Structure - 01 Level and Abv - Fr 52 to Fr

67 (ASC100442)

Coast Guard Drawing 750-WMSL-100-083, Rev , General Arrangement NSC 5 & Follow (AS5100001) Coast Guard Drawing 750-WMSL-100-084, Rev -, Topside Configuration for NSC 6 & Follow

(AS6100004)

Coast Guard Drawing 750-WMSL-100-090, Rev -, General Arrangements NSC 7 and Follow On Coast Guard Drawing 750-WMSL-100-090, Rev A, General Arrangements NSC 7 and Follow

(AS7100001)

Coast Guard Drawing 750-WMSL-100-092, Rev -, Hull Curves of Form (NSC 7 SRD) (ASC100010G) Coast Guard Drawing 750-WMSL-114-001, Rev B, Fairwaters and Rope Guard Installation Details &

L/M (ASC114001)

Coast Guard Drawing 750-WMSL-114-004, Rev B, Stern Tube Bossing and Shaft Handling Padeyes

(ASC114007)

Coast Guard Drawing 750-WMSL-114-004, Rev B, Stern Tube Bossing and Shaft Handling Padeyes

(ASC114007)

Coast Guard Drawing 750-WMSL-114-010, Rev -, Rudder and Appendages Drawing (ASC114006F) Coast Guard Drawing 750-WMSL-114-011, Rev -, Rudder and Appendages Drawing (ASC114006G) Coast Guard Drawing 750-WMSL-161-001, Rev F, Strut Castings (ASC161001) Coast Guard Drawing 750-WMSL-161-002, Rev A, Stern Tube & L/M (ASC161002) Coast Guard Drawing 750-WMSL-167-005, Rev C, Side Port Door Installation & Details (ASC167005) Coast Guard Drawing 750-WMSL-167-501, Rev N-A, Manhole List, Installation and Fabrication Details, Ship Wide (ASC167001) Coast Guard Drawing 750-WMSL-169-003, Rev E, Fabrication & Installation of Transom Doors

(ASC169003)

Coast Guard Drawing 750-WMSL-169-003, Rev E, Fabrication & Installation Transom Doors

(ASC169003)

Coast Guard Drawing 750-WMSL-169-003, Rev E, Fabrication & Installation Transom Doors Coast Guard Drawing 750-WMSL-191-001, Rev G, Diagram Ballast / Dewatering System (ASC191001) Coast Guard Drawing 750-WMSL-191-049, Rev -, Diagram Ballast / Dewatering Diagram Selected

Record Dwg NSC 4 (ASC19001D) Coast Guard Drawing 750-WMSL-191-050, Rev -, Diagram Ballast / Dewatering Diagram Selected

Record Dwg NSC 5 (ASC19001E) Coast Guard Drawing 750-WMSL-191-051, Rev -, Diagram Ballast / Dewatering Diagram Selected

Record Dwg NSC 6 (ASC19001F) Coast Guard Drawing 750-WMSL-191-052, Rev -, Diagram Ballast / Dewatering Diagram Selected

Record Dwg NSC 7 (ASC19001G) viii (Rev-1)

Coast Guard Drawing 750-WMSL-191-053, Rev -, Diagram Ballast / Dewatering Diagram Selected Record Dwg NSC 8 (ASC19001H)

Coast Guard Drawing 750-WMSL-243-007, Rev E, Propulsion Shafting System Arrangement

(ASC243008)

Coast Guard Drawing 750-WMSL-243-008, Rev -, Propulsion Shafting and Appendage (ASC243001B) Coast Guard Drawing 750-WMSL-243-018, Rev -, Propulsion Shafting and Appendage (NSC 7 SRD)

(ASC243001G)

Coast Guard Drawing 750-WMSL-243-018, Rev -, Propulsion Shafting and Appendage (NSC 7 SRD)

(ASC243001G)

Coast Guard Drawing 750-WMSL-244-001, Rev -, Propulsion Shafting System Measured Bearing

Reaction Report (ASC244001) Coast Guard Drawing 750-WMSL-244-002, Rev B, Stern Tube Seal & Strut Bearings Arrangement &

Details & L/M (ASC244002) Coast Guard Drawing 750-WMSL-244-003, Rev -, Propulsion Shafting System Measured Bearing

Reaction Report (AS2244001) Coast Guard Drawing 750-WMSL-259-020, Rev D, Incin & DG Intake & Combustion Exhaust Sup, Dets

& L/M, 2nd Dk - 02 Lvl (ASC259018) Coast Guard Drawing 750-WMSL-259-505, Rev C, SSDG #3 Exhaust Modifications Coast Guard Drawing 750-WMSL-264-500, Rev -, CPP HPU Tanks New Clean Out Access Coast Guard Drawing 750-WMSL-300-002, Rev C, Electrical Standard Details (ASC300003) Coast Guard Drawing 750-WMSL-320-010, Rev G, Power Sys Deck Plan-Second DK, AFT OF FR 52

(ASC320006)

Coast Guard Drawing 750-WMSL-320-025, Rev D, Cathodic Protection System Deck Plan and Elem

WD (ASC320014)

Coast Guard Drawing 750-WMSL-320-025, Rev D, Cathodic Protection System Deck Plan and Elem

WD (ASC320014)

Coast Guard Drawing 750-WMSL-320-038, Rev B, Electrical One LINE Diagram (AS1320001) Coast Guard Drawing 750-WMSL-320-510, Rev U, Electrical One LINE Diagram (ASC320001) Coast Guard Drawing 750-WMSL-320-511, Rev G, Power Sys Deck Plan-Second DK, AFT OF FR 52

(ASC320006)

Coast Guard Drawing 750-WMSL-320-577, Rev A, Electrical Mods Incidental to Stern Gate PWR &

CNTRL Enhancement Coast Guard Drawing 750-WMSL-424-001, Rev D, Electronic Navigation Acoustical Cable Block

Diagram (ASC424001) Coast Guard Drawing 750-WMSL-426-003, Rev B, Speed Log and Depth Finder Transducer Installation and L/M (ASC426003) Coast Guard Drawing 750-WMSL-426-004, Rev B, Speed Log and Depth Finder Transducer Installation and L/M (ASC426003) Coast Guard Drawing 750-WMSL-485-001, Rev L, Sleeves-Pipe Structure Penetration (SP485000)

(UNSIGNED)

Coast Guard Drawing 750-WMSL-505-015, Rev E, Miscellaneous Pipe Fabrication Coast Guard Drawing 750-WMSL-508-001, Rev C, Piping and Machinery Insulation Schedule and L/M

(ASC508001)

Coast Guard Drawing 750-WMSL-520-001, Rev H, Seawater Cooling System Diagram (ASC520001) ix (Rev-1)

Coast Guard Drawing 750-WMSL-520-003, Rev B, Machinery Central Seawater Cooling System Schematic (ASC520012)

Coast Guard Drawing 750-WMSL-520-027, Rev B, Seawater Cooling System WMSL 756 Only

(ASC520001D)

Coast Guard Drawing 750-WMSL-520-028, Rev -, Seawater Cooling System Diagram WMSL 757 Only

(ASC520001D)

Coast Guard Drawing 750-WMSL-520-505, Rev D, Auxiliary Seawater Piping Mods AMMR & Shaft Alley

Coast Guard Drawing 750-WMSL-520-506, Rev E, Auxiliary Seawater Piping Mods Fwd of Fr 52 Coast Guard Drawing 750-WMSL-520-507, Rev F, Auxiliary Seawater Piping Mods Aft of Fr 52 Coast Guard Drawing 750-WMSL-521-008, Rev D, Firemain Unit 1220 (ASC521122-FM) Coast Guard Drawing 750-WMSL-521-014, Rev C, Firemain Unit 2110 (ASC521211-FM) Coast Guard Drawing 750-WMSL-521-018, Rev E, Firemain Unit 2210 (ASC521221-FM) Coast Guard Drawing 750-WMSL-521-020, Rev C, Firemain Unit 2230 (ASC521223-FM) Coast Guard Drawing 750-WMSL-521-022, Rev D, Firemain Unit 2310 (ASC521231-FM) Coast Guard Drawing 750-WMSL-521-026, Rev D, Firemain Unit 3110 (ASC521311-FM) Coast Guard Drawing 750-WMSL-521-048, Rev -, Diagram Firemain Selected Record Dwg WMSL 756 Coast Guard Drawing 750-WMSL-528-003, Rev K, Plumbing and Interior Deck Drain Diagram WMSL

756 AF (ASC528003)

Coast Guard Drawing 750-WMSL-529-003, Rev B, Ballast/Dewatering System Schematic (ASC529019) Coast Guard Drawing 750-WMSL-556-003, Rev E, Label Plate List - Blst/Deballast-Overfl/Ae/St-Hydr

Sys (ASC556002) Coast Guard Drawing 750-WMSL-556-006, Rev F Stern Gate Hydraulic System Diagram (ASC556004) Coast Guard Drawing 750-WMSL-556-006, Rev F, Stern Gate Hydraulic System Diagram Coast Guard Drawing 750-WMSL-556-015, Rev E, Bow Thruster HPU Diagram (ASC556009) Coast Guard Drawing 750-WMSL-556-016, Rev -, Bow Thruster Hydraulic System Description

(ASC556009-02)

Coast Guard Drawing 750-WMSL-556-22, Rev H, Steering Gear and Stern Gate Hydraulic Piping - Unit

3330 (ASC556333-HY)

Coast Guard Drawing 750-WMSL-556-504, Rev C, Mod To Improve Stern Gate Speed Coast Guard Drawing 750-WMSL-556-504, Rev C, Mods to Improve Stern Gate Speed Coast Guard Drawing 750-WMSL-562-001, Rev C, Rudder Bearing Casting (ASC562001) Coast Guard Drawing 750-WMSL-562-002, Rev C, Rudder (ASC562002) Coast Guard Drawing 750-WMSL-562-003, Rev D, Rudder Support System (ASC562003) Coast Guard Drawing 750-WMSL-571-001, Rev D, FAS Arrangement Installation and Details

(ASC571001)

Coast Guard Drawing 750-WMSL-571-500, Rev D, FAS Arrangement Installation and Details

(ASC571001)

Coast Guard Drawing 750-WMSL-581-001, Rev D, Anchor Handling (ASC581001) Coast Guard Drawing 750-WMSL-581-002, Rev B, Anchor Pocket (ASC581002) Coast Guard Drawing 750-WMSL-581-003, Rev C, Hawse Pipe and Chain Pipe (ASC581003) Coast Guard Drawing 750-WMSL-583-002, Rev D, Small Boat Stbd, Hdlg Sys, Arr & Details

(ASC583002)

x (Rev-1)

Coast Guard Drawing 750-WMSL-583-004, Rev H, Stern Launch & Recovery Arrangement & Details

(ASC583004)

Coast Guard Drawing 750-WMSL-583-521, Rev B, Boat Launch and Recovery Ramp Rail Modifications.

Coast Guard Drawing 750-WMSL-602-001, Rev C, Fab & Instl of Ships Name & Draft Markings

(ASC602001)

Coast Guard Drawing 750-WMSL-631-002, Rev P, Paint Schedule (ASC631002) Coast Guard Drawing 750-WMSL-633-001, Rev D, Installation of Cathodic Protection System

(ASC633001)

Coast Guard Drawing 750-WMSL-633-500, Rev F, Installation of Cathodic Protection System

(ASC633001)

Coast Guard Drawing 750-WMSL-635-001, Rev -, Thermal & Acoustic Insulation (ASC635001) Coast Guard Drawing 750-WMSL-635-002, Rev K, Insulation Arr & Details Thermal Acoustic & Fire Coast Guard Drawing 750-WMSL-801-004, Rev A, Booklet of General Plans NSC 3 SRD

(ASC801001C)

Coast Guard Drawing 750-WMSL-801-011, Rev 1, Booklet of General Plans Coast Guard Drawing 750-WMSL-801-012, Rev -, Booklet of General Plans (ASC801001G) (SRD)

(NSC7)

Coast Guard Drawing 750-WMSL-801-012, Rev -, Booklet of General Plans (ASC801001G) Coast Guard Drawing FL-1204-3, Rev A, Fleet Welded Padeyes And Links Coast Guard Fleet Drawing FL 2804-022, Rev A, Consolidated Visual ID for Cutters (Vessels 65 ft and

Over in Length) NAVSEA Drawing 803-921865 Rev R, Cathodic Protection System, Hull Zinc Anodes NAVSEA Drawing 804-5773931, Rev A, Acoustic & Thermal Insulation for Compartments Installation

Details

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) M10360.3 (Series), Coatings and Color Manual Coast Guard Technical Publication (TP) 7007, SWBS 562, Mar 2021, Rudderstock Seal - Type Er + Is Coast Guard Technical Publication (TP) 7034, SWBS 243, Dec 2016, Stern Tube Seal – Type M-9 – P/N

US-75888-01 – Installation, Operation & Maintenance Manual Coast Guard Technical Publication (TP) 7062, SWBS 167, Feb 2021, Sideport Shell Door and Portable

Ladder - Model D-WK-868 Coast Guard Technical Publication (TP) 7069, SWBS 562, Jun 2007, Rudder, Lower Bearing Coast Guard Technical Publication (TP) 7072A, Feb 2016, Controllable Pitch Propeller (CPP) -

Installation Manual Coast Guard Technical Publication (TP) 7073A, Dec 2020, Reduction Gear - Type as 2/250-As 198F Coast Guard Technical Publication (TP) 7079, SWBS 244, Jan 2018, Stern Tube & Strut Bearings –

Models 22022-100/-200 – Installation, Operation & Maintenance Instructions Coast Guard Technical Publication (TP) 7127, Oct 2007, SWBS 524, Simplex Basket Strainer – Sizes

3/8" – 8" – Model 72 Coast Guard Technical Publication (TP) 7140, SWBS 633, Jul 2013, Cathodic Protection Coast Guard Technical Publication (TP) 7153A, SWBS 245, Mar 2016, Controllable Pitch Propeller

(CPP) Users Manual xi (Rev-1)

Coast Guard Technical Publication (TP) 7158, 21-SEP-07, SRD-500 Dual Axis Doppler Speed Log - Operation, Service, & Install

Coast Guard Technical Publication (TP) 7160, 21-SEP-07, SRD-500 Dual Axis Doppler Speed Log – Operation-Operational Manual

Coast Guard Technical Publication (TP) 7202, SWBS 568, Aug 2007, Bow Thruster – Remote Control System – Plant K161 – Instruction Manual

Coast Guard Technical Publication (TP) 7203, SWBS 568, Aug 2007, Bow Thruster – Model TT1100 DPN CP – Mechanical & Hydraulic System – User Manual

Coast Guard Technical Publication (TP) 7410, Feb 2012, SWBS 593, Duplex Basket Strainer – Sizes 3/4"

– 8" – Model 50

Coast Guard Technical Publication (TP) 7413, Feb 2012, SWBS 593, Duplex Basket Strainer – Sizes 3/4"

– 4” – Model 53BTX

Coast Guard Technical Publication (TP) 7426, SWBS 584, Sep 2021, Sliding Double Transom Door for the NSC 1 and NSC 2.

Coast Guard Technical Publication (TP) 7431, SWBS 568, Feb 2012, Bow Thruster Model TT1100 DPN CP – Mechanical & Hydraulic System – Installation Manual

Coast Guard Technical Publication (TP) 7498A, SWBS 568, May 2020, Bow Thruster - Electric Motors – Installation, Operation & Maintenance Manual

Coast Guard Technical Publication (TP) 7525, CIB - Auxiliary Machinery Vol. IV (Hull 750 Only), 2019, SWBS 581 Anchor Storage and Handling

Coast Guard Technical Publication (TP) 7794, SWBS 584, Sep 2021, Sliding Double Transom Door – Model H-WK-868-29

Coast Guard Technical Publication (TP) 9532, CIB - Auxiliary Machinery Vol. IV (Hull 755 Only), 2019, SWBS 581 Anchor Storage and Handling

Coast Guard Technical Publication (TP) S9524-AE-MMO-010, SWBS 521, Dec 1986, Cascade Orificial Resistive Device (CORD)

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General Requirements

Surface Forces Logistics Center Standard Specification 0450 (SFLC Std Spec 0450), 2020, Electrical Power for Contractor’s Tools & Equipment

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2020, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2020, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3401), 2020, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3042 (SFLC Std Spec 3042), 2020, Shipboard Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification 3100 (SFLC Std Spec 3100), 2020, Inspect, Test and Recondition AC Synchronous Machines In-Place

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2020, Auxiliary Machine Systems

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2020, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6341 (SFLC Std Spec 6341), 2020, Install Interior Deck Covering Systems xii (Rev-1)

Surface Forces Logistics Center Standard Specification 8634 (SFLC Std Spec 8634), 2020, Drydocking Surface Forces Logistics Center Standard Specification 8635 (SFLC Std Spec 8635), 2020, Temporary

Services Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2020, Temporary

Services.

Tech Pub 7358, VE5900 Echosounder – Technical Handbook Tech Pub 7480, VE5900 Echosounder Model 5900 Tech Pub 7482, Navigation Echosounder – LAZ-5100

OTHER REFERENCES

48 CFR Sec HSAR 3052.217-94 Lay days (USCG) American Society for Nondestructive Testing (ASNT), Standard No. ANSI/ASNT CP-189-2020, 2020, ASNT Standard for Qualification and Certification of Nondestructive Testing Personnel American Society of Mechanical Engineers (ASME) B16.34, 2020, Valves-Flanged, Threaded, and

Welding End American Society of Mechanical Engineers (ASME) B16.5, 2017, Pipe Flanges and Flanged Fittings:

NPS 1/2 through NPS 24.

American Welding Society (AWS) B1.10M/ B1.10, 2016, Guide for Nondestructive Examination of

Welds American Welding Society (AWS) B1.11M/B1.11, 2015, Guide for the Visual Examination of Welds American Welding Society (AWS) D1.1/D1.1M, 2020, Structural Welding Code – Steel American Welding Society (AWS) D3.5, 2000, Guide for Steel Hull Welding American Welding Society, AWS D1.2-96, 1996, Structural Welding Code, Steel ASNT SNT-TC-1A, 2020, Personnel Qualification and Certification in Nondestructive Testing ASTM D1730-09, Jan 2014, Standard Practices for Preparation of Aluminum and Aluminum-Alloy

Surfaces for Painting ASTM International (ASTM) D1330, 2015, Standard Specification for Rubber Sheet Gaskets ASTM International (ASTM) D1730, 2020, Standard Practices for Preparation of Aluminum and

Aluminum-Alloy Surfaces for Painting ASTM International (ASTM) D3359, 2017, Standard Test Methods for Measuring Adhesion by Tape

Test ASTM International (ASTM) D5363, 2016, Standard Specification for Anaerobic Single-Component

Adhesives (AN) ASTM International (ASTM) F992, 2017, Standard Specification for Valve Label Plates ASTM Internationals (ASTM) G46, 2018, Standard Guide for Examination and Evaluation of Pitting

Corrosion CGTTP 4-11.10A-Water Supply and Wastewater Disposal Tactics, Techniques and Procedures (TTP) Code of Federal Regulations (CFR) Title 29, Part 1910, 2017, Occupational Safety and Health Standards Code of Federal Regulations (CFR) Title 29, Part 1915, 2013, Occupational Safety and Health Standards for Shipyard Employment Code of Federal Regulations (CFR) Title 29, Part 1915, Subpart E, Sep 2015, Scaffolds, Ladders and

Other Working Surfaces Code of Federal Regulations (CFR) Title 40, 2013, Protection of the Environment Commercial Item Description (CID) A-A-59313, Nov 2003, Thread Compound; Anti seize, Zinc Dust-

Petrolatum xiii (Rev-1)

Commercial Item Description (CID) A-A-59875A, 2019, Polysulfide Fairing Compound for Waterborne Main Propulsion Shafting Coverings on U.S. Naval Surface Ships and Submarines

Commercial Item Descriptions (CID) A-A-59323, Rev A; Cloths, Cleaning, Low-Lint Federal Specification (Fed Spec) HH-P-151, July 2020, Packing, Rubber-Sheet, Cloth Insert General Specifications for Overhaul of Surface Ships (GSO), 2004, Section 581 Anchor Stowage and

Handling International Standards Organization (ISO) 4406, 2021-01, Hydraulic Fluid Power – Fluids – Method for

Coding the Level of Contamination by Solid Particles Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2019 Edition, Pressure Testing Of Steel Valves Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-67, 2017 Edition, Butterfly Valves Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72A, 2010 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2019 Edition, Bronze Gate, Globe, Angle and Check Valves MIL PRF-16173 w/Interim Amendment 2, 2017, Corrosion Prevention Compound, Solvent Cut Back, Cold Application MIL-A-18001, Aug 2008, Anodes, Sacrificial Zinc Alloy (Commercially Accepted - ASTM B418) MIL-A-22262B Amendment 2, 2021, Abrasive Blasting Media Ship Hull Blast Cleaning MIL-C-24633A, 2014, Chain, Stud Link, Anchor, Low Alloy Steel, Flash Butt Welded MIL-DTL-23549D, 2021, Grease, General Purpose MIL-DTL-24643, Dec 2011, Cables, Electric, Low Smoke Halogen-Free, For Shipboard Use, General

Specification for MIL-PRF-1149E, Nov 2019, Gasket Materials, Synthetic Rubber, 50 and 65 Durometer Hardness MIL-PRF-17672, 14 Oct 2010, Hydraulic Fluid, Petroleum, Inhibited MIL-PRF-24176C, 2020, Cement, Epoxy, Metal Repair and Hull Smoothing MIL-PRF-24647D, 2021, Paint System, Anticorrosive and Antifouling, Ship Hull MIL-PRF-24667C w/Int. Amendment 1, Mar 2018, Coating System, Non-Skid, for Roll, Spray, or Self-

Adhering Application MIL-PRF-24667D, Feb 2021, Coating System, Non-Skid, for Roll, Spray, or Self-Adhering Application MIL-PRF-900, 2020, Rubber Gasket Material, 45 Durometer Hardness MIL-S-45180, 1998, Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant MIL-STD-1310, Sept 2009, Shipboard Bonding, Grounding, & Other Techniques for Electromagnetic

Compatibility, Electromagnetic Pulse (EMP) Mitigation, and Safety MIL-STD-1627, Sep 1994, Bending of Pipe or Tube for Ship Piping Systems MIL-STD-1689A, 1990, Fabrication, Welding, and Inspection of Ships Structure MIL-STD-2003-3B, Oct 2020, Electric Plant Installation, Standard Methods for Surface Ships &

Submarines (Penetrations) MIL-STD-2199A, 2010, Coverings for Waterborne Main Propulsion Shafting on U.S. Naval Surface

Ships and Submarines MIL-STD-2199B, 2020, Covering for Waterborne Main Propulsion Shafting on U.S. Naval Surface Ships and Submarines xiv (Rev-1)

MIL-STD-419, Aug 2017, Cleaning and Protecting Piping, Tubing and Fittings for Hydraulic Power Transmission Equipment

MSS SP-58, 2018, Pipe Hangers and Supports - Materials, Design, Manufacture, Selection, Application, And Installation

Naval Sea Systems Command (NAVSEA) S9243-AW-TRS-012, Surface Ships Main Propulsion Shafting Examination, Test and Repair Action Record, Volume 1, Part 2

Naval Sea Systems Command (NAVSEA) T9074-AS-GIB-010/271, 1999, Requirements for Nondestructive Testing Methods

SAE International (SAE) AMS3824C, 2013, Cloth, Glass Finished for Resin Laminates SAE International (SAE) AMSC9084, 2013, Cloth, Glass Finished for Resin Laminates SAE International (SAE) AMS-STD-595A, 2017, Colors Used in Government Procurement SAE-AMS-G-6032, Grease, Plug Valve, Gasoline and Oil Resistant SAE-AS8660, Silicone Compound Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) G-6032A, 2012, Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric Society of Automotive Engineers (SAE) J1942/1, 2020, Qualified Hoses for Marine Applications The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2020, Bare Metal Power Tool Cleaning The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP 10 (WAB)/NACE WAB-2, 2015, Near-White Metal Wet Abrasive Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 5/NACE No. 1, 2007, White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 6 (WAB)/NACE WAB-3, 2015, Commercial Abrasive Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 7 (WAB)/NACE WAB-4, 2015, Brush-Off Wet Abrasive Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-4/NACE WJ-4, 2012, Waterjet Cleaning of Metals – Light Cleaning

The Society for Protective Coatings (SSPC)/NACE Joint Surface Preparation Standard SSPC-SP 10/NACE No.2, 2007, Near-White Blast Cleaning xv (Rev-1)

CONSOLIDATED LIST OF GOVERNMENT-FURNISHED PROPERTY

The following is a list of property, which the Government will furnish. This list supersedes any other material obligations indicated or implied by referenced drawings.

WORK

ITEM

MTI ITEM DESCRIPTION NSN/PN QTY ESTIMATED

COST

($/UNIT)

4 N Coast Guard Emblem Vinyl

Kit N/A 2 ea. 1,800.00

4 N Freeboard/Superstructure/Mast (Freeboard/Superstructure, Steel), Option 1

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 25,500

SF

To be determined upon product selection

5 N Coast Guard Emblem Vinyl Kit

N/A 2 ea. 1,800.00

5 N Freeboard/Superstructure/Mast (Freeboard/Superstructure, Steel), Option 1 (Deckhouse and Hangar

Preservation)

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 6,000

SF

To be determined upon product selection

5 N Smoke Stack (Smoke Stack Casing, Steel Exterior) (Stack Preservation)

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 6,000 SF (White Topcoat), 2,000 SF

(Black

Topcoat)

To be determined upon product selection

5 N Machinery, Deck (Adjacent Structures, Systems, or Outfits)

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 2,000 SF (White Topcoat)

To be determined upon product selection

6 N Underwater Water (U/W) Body and Boot-Top (U/W Body and Boot-Top, Steel

Hulls (Up to 12 Years), in Salt Water)

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 27,781

SF

(Underwater

Body), 2,000 SF

(Boot Top)

To be determined upon product selection

9 N WASHER, SHOULDER,

.386"ID X .484"OD X .375"L

X .875FLANGE OD X .062

FLANGE THICKNESS,

12SWS3514

16 ea.

9 N WASHER SHOULDER,

.375"ID X .5"OD X .188"L X

.063"THICK, 12SWS2556

WASHER USA

376 ea.

14 N Gasket 1" x 2-1/8" Neoprene (25 duro) Walz and Krenzer

NSN: 5330-01-562-8925

PN: D-WK-868-1-PC7

1 1460.00 xvi (Rev-1)

91 Willennbrock Road Unit B4, Oxford CT, 06478 phone

203-267-5712 14 N Hinge Pin 1-1/4 DIA 316

CRES, Walz and Krenzer

PN: D-WK-868-5-4 2 188.00

14 N Hinge Washer, Beemer, Oilite Bronze

PN: TT-2006-1 4 7.00

15 N Freeboard/Superstructure/Mast (Freeboard/ Superstructure, Aluminum/Steel) Option I

Authorized coating system per SFLC Std Spec 6310, Appendix C

Coverage for: 2,400 SF (White Topcoat), 4,200 SF

(Black

Topcoat)

To be determined upon product selection

15 N Gasket, EMI/EMP, Conductive Elastomer, Polasheet with Aluminum, 15 in x 15 in x 1/8 in, Silicone

NSN : 5999-DAO-826037 10 ea. 150.00

15 N Gasket, EMI/EMP, Conductive Elastomer, Polasheet with Monel, 15 in x 15 in x 1/8 in, Silicone

NSN : 5330-DAO-695609 10 ea. 150.00

15 N SCREW, HEX HEAD, 1-1/2"-

6UNC-2A X 6-1/2"L

124 ea.

15 N NUT, HEX, 1-1/2"UNJC-3B 124 ea.

18 N Major Overhaul Kit NSN: 2840-01-576-0008

PN: WLP001354-001

2 ea. 85,230.00

19 N Plug (SL231) NSN: 5340-22-624-9161

PN: F007867

4 75.00

19 N O-Ring (SL231) NSN: 5331-22-624-9162

PN: F088083

4 5.00

19 N O-Ring (07309) NSN: 5331-01-644-0284

PN: F088595

10 300.00

19 N Sealing Compound (R4440) NSN: 8030-22-621-2495

PN: F067211

4 60.00

19 N Lubricant NSN: 9150-22-621-2497

PN: F067665

4 40.00

19 N Grease PN: K192698 1 600.00 19 N Lubricant NSN: 9150-22-621-2498

PN: F067061

2 200.00

19 N Break bolt PN: F000972 10 320.00 19 N Lock pin PN: F000118 80 10.00 24 Y ***Fathometer Transducer

Shallow Water, 200 kHz ELAK Nautik LSE 313 1 ea. $750.00

28 Y Seat Assembly, Split NSN: 2040-01-674-3269

PN: H75378-01-4

2 ea. $20,000.00

28 N Overhaul Kit for Rudderstock Seal Type ER+IS, H75378-01

NSN: 2040-01-586-3349

PN: WLP00142-001

2 ea. $32,000.00

28 N Seal, Chevron Packing Style, PN: Garlock Style 432 2 ea. $500.00 xvii (Rev-1)

14.17 in. ID, 15.67 in. OD 29 N Kongsberg Spare Part Kit PN: RRM000445315 2 ea. $29,929.00 29 N Kongsberg Bearing Shell PN: 60705-8819 32 ea. $939.50 29 N Kongsberg Seal Kit PN: RRM00044570 2 ea. $1,861.13 29 Y Rotor PN: 60105-9861 1 ea.

29 N Adapter Sleeve PN: SR740B-13 1 ea.

30 N Bow Thruster Dry Dock Kit NSN: 2090-01-698-8024

PN: U-1-9-97

1 ea. 14,300.00

35 N Anode Assembly 5342-01-540-3444 / W3T106665

6 ea. 15228.00

36 N Reference Electrode, Silver & Silver Chloride (Evoqua

Water Technology)

6160-01-118-4721 / W3T105304

4 ea. 4,500.00

36 N O-RING 4 ea.

36 N WASHER, LOCK,

CORROSION RESISTANT

16 ea.

36 N RING, GLAND 4 ea.

36 N WASHER, LOCK, SPLIT

STAINLESS

4 ea.

36 N ASSY-PACKING, (16'

CABLE)

4 ea.

36 N BUSHING, TEFLON 4 ea.

37 Y 16 Inch IPS, Butterfly Valve, CRES CL, 150 Flange with stellite, GR 21, Seat

Duplex/GPH Seal and packing Triple, Off set with Gear

Operator by Vanessa Tyco or Equal

CEDG3-V-2 1 ea. $16,360.00

37 N LOCK (TAB) WASHER, 16

GA, FOR 1-1/8" BOLT

32 ea.

37 N SCREW, HEX HEAD CAP,

1-1/8"-8 UNC-2A X 3 LG

WASHER FACED

16 ea.

37 N NUT, HEX, 1-1/8"-8 UN-2B,

WASHER FACED

16 ea.

37 N LOCK (TAB) WASHER, 16

GA, FOR 1" BOLT

32 ea.

39 N TUBE, 1 INCH OD X 0,095"

WALL, SEAMLESS, ASTM,

A312 (Piece 13 of Coast Guard Drawing 750-WMSL-

556-504)**

10 Feet $250.00

39 N Integrated Motor Pump, 460 Volt AC, 60 HP Motor (Piece 15 of Coast Guard Drawing

750-WMSL-556-504) **

MP45-B1-R-VQ81N-B-

F1/V003-A-F1

1 ea. 14,588.00

39 N DIRECT -ACTING RELIEF SUN HYDRAULICS 1 $500.00

xviii (Rev-1)

VALVE - PILOT

CAPACITY, 2,5 GPM

CAPACITY, T-8 CAVITY,

1000 PSI SET POINT(Piece 49 of Coast Guard Drawing

750-WMSL-556-504) **

RBAECAN

39 N LINE MOUNT MANIFOLD

SIZE -06 (9/16" -18 UN/UNF-

2B) SAE - ORB FEMALE

PORTS, 90 DEGREE FLOW

PATH, T-8A CAVITY (Piece 50 of Coast Guard Drawing

750-WMSL-556-504) **

SUN HYDRAULICS

WFO

2 $250.00

39 N ROTARY FLOW DIVIDER,

EXTERNAL GEAR, 1 1/4"

FEMALE SAE ORB INLET

X 2 EACH 1: FEMALE SAL

ORB OUTLETS, NO RELIEF

VALVE, 50 GPM MAX

INLET FLOW (Piece 57 of Coast guard Drawing 750-

WMSL-556-504)**

ROTARY FLOW

DIVIDER, DELTA

POWER P47

1 $500.00

39 N PILOT-OPERATED,

BALANCED PISTON

RELIEF VALVE

CARTRIDGE, 50 GPM

CAPACITY, T-3A CAVITY,

1000 PSI SET PONT (Piece 58 of Coast Guard Drawing

750-WMSL-556-504) **

SUN-HYDRAULICS

RPGC-LAN

2 $250.00

39 N LINE MOUNT MANIFOLD,

THROUGH PORT WINI

GAUGE PORT, SIZE -16 (1

5/16"-12 UN/UF-2B)

FEMALE SAE-ORB UNE

PORTS,SIZE -04 (7/16"-20

UN/UNF-2B) FEMALE SAE-

ORB GAGE PORT, T-3A

CAVITY (Piece 59 of Coast Guard Drawing 750-WMSL-

556-504) **

SUN HYDRAULIC VFW 2 $500.00

39 N DO8 STANDARD FLOW

PARALLEL MANIFOLD, 4

STATIONS, SAE-ORB

PORTS, WITH "X" PORT

OPTION AND SUN CAVITY

T-3A FOR RELIEF VALVE

CARTRIDGE (Piece 67 of Coast Guard Drawing 750-

WMSL-556-504) **

DAMAN DD8P0455/1S 1 $750.00

39 N ADJUSTABLE NEEDLE SUN HYDRAULIC 3 $75.00

xix (Rev-1)

VALVE CARTRIDGE, 140

GPM CAPACITY, T-18A

CAVITY (Piece 68 of Coast Guard Drawing 750-WMSL-

556-504) **

NFFDLIN

39 N SANDWICH MANIFOLD,

ISO 08, T-18-A CAVITY ON

P (Piece 69 of Coast Guard Drawing 750-WMSL-556-

504) **

SUN HYDRAULIC IBO 3 $500.00

39 N FAST-ACTING, PILOT-

OPERATED, BALANCED

PISTON RELIEF VANE

CARTRIDGE, 50 GPM

CAPACITY, T-3A CAVITY,

1100 PSI SET POINT (Piece 70 of Coast Guard Drawing

750-WMSL-556-504) **

SUN HYDRAULIC

RPGELAN

1 $500.00

39 N DIRECTIONAL CONTROL

VALVE, DOUBLE

SOLENOID, 3 POSITION ,

SPRING CENTERED, EXT

PLOT, INTERNAL DRAIN,

120 VAC/60 HZ, MANUAL

OVERIDE , MANAPLUG

(MIN) WITH LIGHTS (Piece 71 of Coast Guard Drawing

750-WMSL-556-504) **

PARKER

D61VW00C5NYGP56

3 $350.00

39 N DIRECTIONAL CONTROL

VALVE, SINGLE

SOLENOID, 2 POSITION,

SPRING CENTERED, EXT

PLOT, MEDIAL DRAIN, 120

VAC/60 HZ, MANUAL

OVERIDE, MANAPLUG

(MINI) WITH LIGHTS (Piece

72 of Coast Guard Drawing

750-WMSL-556-504) **

PARKER

D81VW002E5NYGP56

1 $500.00

39 N PILOT-TO-OPEN CHECK

VALVE WITH STANDARD

PILOTCARTRIDGE, 60

GPM CAPACITY, T-17-A

CAVITY (Piece 73 of Coast Guard Drawing 750-WMSL-

556-504) **

SUN HYDRAULIC

CKGBXCN

2 $250.00

39 N SANDWICH MANFOLD ISO

08, ON A AND B W1TH

CROSS PILOT, T-17-6

CAVITY (Piece 74 of Coast Guard Drawing 750-WMSL-

556-504) **

SUN HYDRAULIC

HBN/S

2 $500.00 xx (Rev-1)

39 N PLUG, HEX HEAD, SIZE -16

(1 5/16"-12 UN/UNF-2A)

MALE SAE-ORB (Piece 75 of Coast Guard Drawing 750-

WMSL-556-504) **

PARKER 16 PSON 5 $25.00

39 N PLUG, HEX HEAD, SIZE -20

(1 5/8"-12 UN/UNF-2A)

VALE SAE-ORB ORB (Piece 76 of Coast Guard Drawing

750-WMSL-556-504) **

PARKER 20 PSON 1 $25.00

39 N UNION, 1" PS FEMALE

SOCKET WELD X WE -16

(1 5/16"-12 UN/UNF-2A)

MALE SAE-ORB (Piece 85 of Coast Guard Drawing 750-

WMSL-556-504) **

DERBYSHIRE MARINE

MP303-5-16

15 $10.00

39 N LINE MOUNT MANIFOLD ,

CROSS PILOT, 1" SAE ORB

LNE PORTS, T-17A

CAVITIES, 2 CAVITIES

(Piece 89 of Coast Guard

Drawing 750-WMSL-556-

504) **

SUN HYDRAULIC YJM 2 $250.00

39 N 3,1 PILOT RATIO, ,

STANDARD CAPACITY

COUNTERBALANCE

VALVE, 60 GPM

CAPACITY, T-17A CAVITY,

1000 PSI RELIEF SET PONT

(Piece 90 of Coast Guard Drawing 750-WMSL-556-

504) **

SUN HYDRAULIC

CGGALHN

4 $100.00

39 N PIPE, 1/2" IPS, SCHD 40,

SEAMLESS, ASTM A3I2

(Piece 93 of Coast Guard

Drawing 750-WMSL-556-

504) **

3, 4’ Segments

$250.00

39 N DIRECT-ACTING RELIEF

VALVE - PILOT

CAPACITY, 2,5 GPM

CAPACITY, T-84 CAVITY,

200 PSI SET POINT (Piece 103 of Coast Guard Drawing

750-WMSL-556-504) **

SUN HYDRAULIC

RBAECEN

1 $250.00

39 N Topworx 7FA6-73658-3DD 4 605.00 39 N Topworx 7FD1-73658-3DD 2 619.00 39 N Topworx 7FG7-73658-3DD 2 633.00 39 N Topworx 3PIN IMPLLSE, 2 ft

Cable 8 150.00

39 N Center Gasket OEM Dwg# D- NSN: 5330-01-649-2524 1 390.13 xxi (Rev-1)

WK-868-40 (Item 06) 39 N Port Upper Gasket OEM

Dwg# D-WK-868-40 (Item 12)

39 N Port Lower Gasket OEM Dwg# D-WK-868-40 (Item

13)

NSN: 5330-01-649-2507 1 390.13

39 N Stbd Upper Gasket OEM Dwg# D-WK-868-40 (Item

14)

NSN: 5330-01-649-7389 1 390.13

39 N Stbd Lower Gasket OEM Dwg# D-WK-868-40 (Item

15)

NSN: 5330-01-649-7391 1 390.13

39 N Port Lower Guide Rail OEM Dwg# D-WK-868-42 (Item

24)

NSN: 5340-01-649-7443 1 2,950.00

39 N Port Middle Guide Rail OEM Dwg# D-WK-868-42 (Item

25)

NSN: 5340-01-649-7452 1 2,950.00

39 N Port Upper Guide Rail OEM Dwg# D-WK-868-42 (Item

26)

NSN: 5340-01-649-7462 1 2,950.00

39 N Stbd Lower Guide Rail OEM Dwg# D-WK-868-42 (Item

27)

NSN: 5340-01-649-7470 1 2,450.00

39 N Stbd Middle Guide Rail OEM Dwg# D-WK-868-42 (Item

28)

NSN: 5340-01-650-1580 1 2.450.00

39 N Stbd Upper Guide Rail OEM Dwg# D-WK-868-42 (Item

29)

NSN: 5340-01-650-1575 1 2,450.00

39 N JUMO Thermometer 608540/0280-643-00-0- 847-8-144-26-150- 21/5220 Scale C+F

1 452.42

39 N MOTOR CIRCUIT

PROTECTOR, 3 POLE,

600V, 150A FRAME, 120

VAC SHUNT TRIP, W/

ADJUSTABLE TRIP

SETTINGS (DIAL

POSITION SET AT "D" 69.2-

80.6A)

HMCP150T4CS05 1 ea. 5,500.00

39 N CIRCUIT BREAKER

MOUNTING ASSEMBLY,

PLUG-IN BASE, U/W PC #4.

PC4754 1 ea. 1,600.00

39 N CIRCUIT BREAKER; 3

POLE, 600V, 1 ODA,

MOLDED CASE,THERMAL

-MAGNETIC BREAKER,

50'C UL 489 SUPPL SB

HHFD63B100NLNAV 1 ea. 11,500.00 xxii (Rev-1)

39 N CHECK VALVE, SIZE -08

(3/4"-16 UN/UNF-2B)

FEMALE SAE ORB

1 ea.

39 N CHECK VALVE, SIZE -06

(9/16"-18 UN/UNF-2B)

FEMALE SAE ORB

1 ea.

39 N NUT, ZINC-PLATED

STEEL, 3/8"-24 UNF

4 ea.

39 N TUBE SLEEVE, REDUCER,

1/2 INCH X 1/4 INCH

3 ea.

39 N CHECK VALVE, SIZE -20

(1-5/8" -12 UN/UNF-2B

3 ea.

39 N WASHER, FLAT, ZINC-

PLATED STEEL, 3/16"

THICK FOR 5/8"

DIAMETER BOLT

4 ea.

39 N 90 DEGREE FLANGED

ELBOW, 1-1/4" SAE CODE

61 X MALE 1-1/4" ORFS

8 ea.

39 N TUBE, SLEEVEL,

REDUCER 1 INCH X 1/2

INCH

12 ea.

39 N FLANGE, SOCKET WELD

PIPE, O RING FACE, 3

INCH, 4 BOLT, SAE CODE

1 ea.

39 N SWITCH, PUSHBUTTON,

MOMENTARY, 1 N0-1 NC,

WITH 120 VAC RED

INCANDESCENT

INDICATOR, 30.5 MM

1 ea.

42 N Weather Decks (Weather Deck Non-Skid, MIL-SPEC Coating for Aluminum/Steel)

(MIL-PRF-24667D

Type V Comp. G/D/L Non-skid)

Authorized coating system per QPD/QPL 24667

(Type V Comp. G/D/L)

Coverage for: 900 sqft

To be determined upon product selection

*Government-loaned property, which shall be returned to the vessel upon completion of the availability.

**New or refurbished equipment that the Government may provide for installation in place of existing equipment.

***Government-furnished property, which is to be supplied by either the vessel or the C4IT ServiceCenter xxiii (Rev-1)

CONSOLIDATED LIST OF CRITICAL INSPECTION ITEMS

The following is a list of work items, which contain Critical Inspection reports, which the Contractor must complete within the first 25% of the availability contract period (see SFLC Std Spec 0000, paragraph 3.2.6.5 (Inspection report particulars)):

Work Item Title

3 Hull Plates (U/W Body), Inspect

11 Chain Lockers and Sump, Clean and Inspect

12 Voids (Non-Accessible), Preserve

16 Propulsion Shaft Alignment & Bearings (External) Clearances, Check

17 Propulsion Shaft Coverings (MIL-STD-2199B), Inspect and Repair

19 Controllable Pitch Propeller Hub Assembly, General Maintenance

25 Sea Valves and Waster Pieces, Overhaul Or Renew

27 Rudder Stock Bearings, Check Clearances

30 Bow Thruster Unit (General), Overhaul

33 Impressed Current Cathodic Protection System, Inspect and Maintain

34 Cathodic Protection (Zincs), Renew xxiv (Rev-1)

PRINCIPAL CHARACTERISTICS

418' WMSL

PHYSICAL

Length overall 418' 0" Length between perpendiculars 390' 0" Maximum beam 54' 0" Beam @ 01 level 47' 9-1/8" Depth (01 level @ side to baseline) 39' 2-3/4" 01 deck camber foredeck 1/4" in 1'-0" Minimum berth depth 20' 0" Height of highest projection Approximately 119' Draft, design 14.40' Design displacement 3925 long tons

MACHINERY

Two diesel engines MTU 20V, 20-cylinder 9,730 SHP each One gas turbine General Electric LM2500; 29,500 SHP Type of propulsion CODAG Electrical system 24 Volt DC Two controllable pitch propellers Rolls-Royce 5 blade, 14' 0" diameter; 229 RPM max Two reduction gears RENK One cross connect gear RENK

HULL

Hull material 5086 Aluminum HSLA-80 Steel ABS EH 36 Steel

ABS AH 36

Frame spacing FWD of FR 9 2' 3" FR 9 to FR 10 6' 9" FR 10 to FR 98 4' 1" FR 98 to FR 99 3'-8"

ELECTRICAL

Power Three 1360 kW, 450 V, 60 Hz, 3 Phase, 1800 RPM Caterpillar 3512B diesel engines with Baylor ship service generators Shore tie cable Seven MIL-C-24368/2 (NATO) shore power receptacles, 400 A each

TANK CAPACITIES

Diesel oil 220,359 gal Fresh water 12,454 gal JP-5 Fuel 35,182 gal

1 (Rev-1)

00000_0821_FLT

REC_00000_FLT_Commercial Project @ Contractor’ Facility (0121)

General Requirements

1. SCOPE

1.1 Intent. This standard specification invokes general requirements for conducting vessel repairs performed at a commercial contractor’s facility for Coast Guard vessels.

1.2 Term interchangeability. The terms 'Contractor', 'CG Yard', 'NAVSTA ', 'shipyard', 'Base', and 'Coast Guard Industrial' are used interchangeably in this specification. Where the primary service provider is Coast Guard personnel, references to contractor and other noted descriptors within this specification or within drawings, publications, SFLC Standard Specifications or other commercial and military references are deemed the same as prime service provider.

2. REFERENCES

COAST GUARD DRAWINGS

None

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) M10360.3 (series), Coatings and Color Manual Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General

Requirements Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2020, Welding and

Allied Processes Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2020, Requirements for Preservation of Ship Structures

OTHER REFERENCES

None

3. REQUIREMENTS

3.1 General. The Contractor must conform to all requirements specified in SFLC Std Spec 0000 and in this item, as applicable, during the performance of this availability. The requirements of this WI applies to all work under the scope of this contract, whether explicitly stated in all following work items or not, and to all other work subsequently authorized by changes, modifications, or extensions to the contract.

2 (Rev-1)

3.1.1 NAVSEA drawings listed will be available FOR INSPECTION ONLY from the Coast Guard post-award.

SFLC will not redistribute NAVSEA documents. Contractors can apply to NAVSEA headquarters directly for copies.

3.2 Contractor-provided fire watch personnel. The Contractor must provide fire watch personnel and equipment.

3.3 Preservation requirements. The Contractor must accomplish all preservation tasks, including touch-ups, in accordance with SFLC Std Spec 6310.

3.3.1 Brand name approval. Ensure that all contractor-furnished coatings are in accordance with SFLC Std Spec 6310, Appendix C (Authorized Coatings for Use on Cutters and Boats).

3.3.2 Coating colors and system color schemes. The Contractor must obtain a written KO authorization to deviate from any coatings required in SFLC Std Spec 6310 Appendix C before work.

3.3.3 In-process quality control measures. The Contractor must abide by all the safety, preservation, and quality control requirements specified in SFLC Std Spec 0000, paragraph 3.2.4.2 (In-process QC measures for “critical-coated surfaces”).

3.3.3.1 Quality control requirements. The Contractor must abide by the following when performing preservation related inspections. The following measurements must be randomly spaced throughout for the purposes of providing a representation of the entire prepared or coated surface.

3.3.3.1.1 Surface profile measurements. One surface profile measurement must be taken for every 200 square feet for the first 1000 square feet; for each additional 500 square feet or less, one profile measurement must be taken.

Profile measurements must be taken in accordance with SFLC Std Spec 6310, paragraph 3.1.8.3 (Surface profile measurements). A “measurement” for surface profile is defined as follows:

• ASTM D4417, Method B: One profile measurement is the average (mean) of 10 individual readings.

• ASTM D4417, Method C: One profile measurement is the average (mean) of 2 individual readings.

3.3.3.1.2 Soluble salt conductivity measurements. 5 conductivity measurements must be taken every 1000 square feet. For submerged (immersed) applications conductivity measurements must not exceed 30 microsiemens/cm.

For non-submerged (non-immersed) applications conductivity measurements must not exceed 70 microsiemens/cm. If a conductivity check fails, clean the surface in accordance with SFLC Std Spec 6310, paragraph 3.1.8.5 (Soluble salt removal).

3.3.3.1.3 Coating thickness measurements. Three area measurements must be taken for the first 1000 square feet;

for each additional 1000 square feet, perform an additional area measurement. A “measurements” for coating thickness is defined as follows:

• SSPC-PA 2 defines an area measurement as 5 separate spot measurements randomly spaced throughout a 100 square foot area.

• SSPC-PA 2 defines a spot measurement as 3 gage readings and each new gage…