60291230 CLEAN.pdf
PDF 217 KB Posted
- Attached to
- BELLOWS
- Solicitation number
- SPMYM2-26-Q-7526
About this file
This is a Cleanliness Requirements specification document (Doc# 6029-1230) that establishes standards for component cleanliness at the point of shipment following fabrication completion.
The specification requires all applicable hardware internal surfaces and parts to be dry and visually clean, free of dirt, loose corrosion products, grease, oil, machining particles, and other foreign material. Acceptable conditions include thin adherent oxidation films from heat treatments or welding, light superficial rust films on carbon or alloy steel, and discrete lint fibers less than one-fourth inch in length. For internal surfaces and parts that cannot be cleaned after assembly, cleaning and inspection must occur prior to the assembly operation that precludes further cleaning, with protection from dirt, grit, cutting oils, and foreign material maintained during subsequent assembly operations. Flushing may be employed for post-assembly cleaning where demonstrated effective for the specific hardware geometry and material. Prior to shipment, visual inspection of internal surfaces and parts through remaining hardware openings must verify compliance with the cleanliness standard. Following inspection, all uncovered hardware openings must be sealed with temporary cleanness covers or captivated plugs constructed of rigid rubber, rigid plastic, or metal. Cover and plug materials are prohibited from containing sulfur or other halogens in their chemical structure, with specific exclusions for fluorocarbon and chlorocarbon materials such as Viton and Neoprene. Internal parts packaged separately shall be sealed in plastic bags or other suitable packaging designed to maintain cleanliness.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Solicitation - SPMYM226Q7526.pdf | ||
| 60291230 CDRL 2.pdf | ||
| SOLE SOURCE.docx | DOCX document | |
| 60291228 CDRL 2.pdf | ||
| 60291228 CDRL.pdf | ||
| 60291227 CDRL 3.pdf | ||
| 60291226 cdrl 2.pdf | ||
| 60291229 CDRL.pdf | ||
| 60291227 CDRL 2.pdf | ||
| 60291229 CLEAN.pdf | ||
| 60291227 CLEAN.pdf | ||
| 60291229 CDRL 3.pdf | ||
| 60291229 CDRL 2.pdf | ||
| 60291226 cdrl.pdf | ||
| 60291227 CDRL.pdf | ||
| 60291230 CDRL.pdf | ||
| 60291228 CLEAN.pdf | ||
| 60291226 CLEAN.pdf | ||
| 60291226 cdrl 3.pdf | ||
| 60291230 CDRL 3.pdf |
Show all 20
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Cleanliness Requirements. Doc# 6029-1230
3.a When the component is ready for shipment after completion of fabrication, all applicable hardware internal surfaces and parts shall be dry and visually clean (e.g. free of dirt, loose corrosion products, grease, oil, machining particles, and other foreign material). A thin adherent oxidation film from heat treatments or welding, a light superficial rust film on carbon or alloy steel, and a few discrete lint fibers (less than one fourth inch In length) are acceptable.
b. Internal surfaces and parts, which cannot be cleaned after assembly shall be cleaned and inspected prior to the assembly operation that precludes further cleaning. During subsequent assembly operations, such parts shall be protected from entry of dirt, grit, cutting oils, and other foreign material. However, flushing may be used to clean after assembly where it
Is demonstrated to be effective for the hardware geometry and material to be removed.
c. A visual inspection of internal surfaces and parts through remaining hardware openings shall be performed prior to Shipment to verify compliance with paragraph 3.a above.
Following this inspection, all hardware openings not covered by permanent closures shall be scaled with temporary cleanness covers or captivated plugs made of rigid rubber, rigid plastic, or metal. Except for polytetrafluoroethylene (Teflon), covers or plug materials shall not contain sulfur or other halogens In their chemical structure. For example, fluorocarbon (e.g. Viton) or chlorocarbon (e.g., chloroprene [Neoprene)) rubber or plastic shall not be used for these covers or plugs. Internal parts, if packaged separately, shall be sealed in plastic bags or other suitable packaging that maintains cleanliness.
File details come from the government source that posted it. Updated .