31140PR260000021 PWS.pdf

Performance Work Statement

U.S. Coast Base Kodiak Environmental

Kodiak, Alaska

1. INTRODUCTION

U.S. Coast Guard (USCG) Base Kodiak requires services for the preparation, shipment, and off-site disposal or recycling of hazardous waste and/or other regulated wastes as noted in section 11.

Base Kodiak is located on the east side of Kodiak, Island, approximately 8 miles south of the City of

Kodiak. The Base Transportation Disposal and Storage Facility is located inside a secured fence line above Windrider Drive just off Seafarer Drive and operates as a Large Quantity Generator under

Generator ID AK9690330742.

2. CONTRACTOR SUPPORT

2.1 Contractor is to provide the following services for Federal and State regulatory compliant disposal of the Hazardous Waste noted in section 11. The Contractor agrees to provide all services necessary for the shipment preparation, transportation, final treatment, disposal, and/or recycling of the items listed in accordance with (IAW) all local, state, and federal laws and regulations, and the terms and conditions of this contract. These services shall include all necessary personnel, including applicable Subcontractors, labor, transportation, equipment, and the compilation and submission of all documentation required by this contract. The Contractor should anticipate shipping up to 10 additional Universal Waste containers not noted in section 11.

2.2 All items, regardless of the condition, are being discarded by the Government (USG) and will require recycling or disposal. The requirements for removal of wastes under this contract are divided into three main phases: Pre-Removal, Removal, and Post-Removal. The Contractor and their Subcontractors must always perform in a prudent, conscientious, safe, and professional manner. The Contractor shall ensure that its agents, employees, and Subcontractors involved in handling and packaging the hazardous waste are trained for the level of expertise required for the proper performance of the task; in particular, the areas of chemical incompatibility, general first aid procedures, and spills. The Contractor shall provide all Materials Handling Equipment (MHE) and Personal Protective Equipment (PPE), unless otherwise stated. The MHE and PPE must be appropriate to safely handle the hazardous waste, to include meeting any additional military installation specific requirements. The Contractor agrees that all personnel and equipment used in the performance of this contract are subject to safety inspections by

USG personnel while on federal property. Without additional expense to the USG, the Contractor shall be responsible for paying all fees, preparing, or obtaining any necessary licenses, permits, notifications, waste profiles, or reports, which result from a Contractor’s transportation, recycling, or disposal decision.

This includes any fees associated with requirements of the Environmental Protection Agency (EPA) national electronic manifest (e-Manifest) system. This includes acquiring any required permits or registrations necessary to operate on any installation listed in this contract and completing the

Notification of Regulated Waste Activity form for the Generator(s) of hazardous waste to sign and file with the applicable state regulators for waste disposal. This includes signing (on behalf of the USG) waste profiles requested by Transportation Storage and Disposal Facility (TSDF). All Contractor-signed waste profile sheets shall be written for the actual waste stream using the Generator’s profile for backup documentation. All Generator forms or other means of notifications, including correspondence with federal or state agencies on behalf of a Generator must be coordinated with and concurred with by the affected Generator prior to submission to any federal or state agency. A copy of all forms and relevant documentation, including correspondence shall be provided to the Contracting Officer Representative

(COR).

2.3 The Contractor and any Subcontractor(s) shall use only the facilities and transporters currently (at the time) listed in the Defense Logistics Agency Disposition Services (DLADS) Qualified Facilities List

(QFL) and Qualified Transporters List (QTL).

2.4 The Contractor may be required to attend special training, seminars, instructions, classes, safety orientations, etc., provided by the USG or to provide information to perform work or gain access to the installation. Example: pass and ID requirements, antiterrorist training, Environmental Management

System (EMS) policies, and/or forklift training.

2.5 All references to manifests in this contract refer to the appropriate shipping documents. The

Contractor shall use only a Non-Hazardous Waste Manifest or a Uniform Hazardous Waste Manifest for shipments of waste under this contract. Bill of Lading (BOL) documents are prohibited for use under this contract. Some states may require the use of state-specific waste codes and/or have unique requirements regarding the use of manifests. The Contractor will comply with all such state requirements in the performance of this contract.

2.6 All documentation shall be clearly marked with the name of the Generator, contract, and other applicable information required under local, state, and federal regulation. Emergency response information and 24-hour emergency phone numbers shall be listed on the manifest. If blocks for emergency information are not provided, this information shall be placed in the upper right-hand corner of each document.

2.7 Electronic Manifest System (e-Manifest system): Generators may continue to use paper manifests during their transition to fully electronic manifests in the e-Manifest system and the phase out of paper manifests. For this contract, the USG will provide Signatory on all shipping documents. The Contractor shall provide the USG a copy of the completed form(s) for review at least five (5) business days prior to removal. Upon Initial Transporter signature, the USG will require a paper copy for record keeping.

3. NOTIFICATIONS

3.1 Upon notice to proceed, Contractor will have 30 days to initiate shipment unless otherwise approved by the Contracting Officer (KO).

3.2 Except as may otherwise be specified herein, the Contractor shall notify the COR or other USG representative, at least five (5) business days before attempting site visits, providing services, or removal efforts. In addition to the notification above for removal efforts, the Contractor shall provide the name of the driver, the driver’s Commercial Driver License (CDL) number and its expiration date, to the COR or other USG representative at least 24 hours prior to removal. The Contractor may also opt to provide a list of approved, multiple drivers designated for pickups under this specific contract to the COR, or other

USG representative prior to any attempted removals. If this option is elected and the list is approved by the USG and maintained by the Contractor, the 24-hour notification requirement is mute for the remainder of the contract unless otherwise modified.

3.3 If a driver, other than the one specified 24 hours in advance for the specific Task Order (TO) or, one whose name does not appear on the optional list of approved or multiple drivers arrive for pickup, the COR or other designated USG representative will verify the personnel change with the Contractor before the pickup commences. The COR or any USG representative has the right to request any identification and/or occupational endorsements from the driver beyond what is identified in additional specific sections in this contract and can refuse commencement and/or completion of pickups if any unusual or suspicious actions occur. Any potential demurrage associated with the driver verification process and/or the unexpected halt or commencement of pickups will not be grounds for reimbursement by the USG.

3.4 The service to be performed under this contract shall be performed during normal Base Kodiak working days/hours, except for Federal holidays. Work that cannot be completed by close-of-business shall be discontinued and resumed the next business day, unless approved by the KO. Services will not be scheduled to be performed on a regular Federal holiday (see below), or one designated by Presidential proclamation. Normal hours of operations for this contract are between 8:00am and 4:00 pm AST.

2025/2026 Federal Holidays

New Year’s Day - 01 January*

Martin Luther King's Birthday – 20 January / 19 January

Presidents Day – 17 February / 16 February

Memorial Day – 26 May / 25 May

Juneteenth National Independence Day – 19 June

Independence Day - 04 July*

Labor Day – 01 September / 07 September

Columbus Day – 13 October / 12 October

Veterans Day - 11 November*

Thanksgiving Day – 27 November / 26 November

Christmas Day - 25 December*

*The holiday is observed on the preceding Friday or the following Monday when the holiday occurs on

Saturday or Sunday, respectively.

4. CONTRACTOR PERSONNEL

All Contractor personnel performing work under this Performance Work Statement (PWS) shall be qualified via training and experience, commensurate with the duties being fulfilled, to the minimum requirements under relevant 29 CFR-OSHA, 40 CFR-EPA, 49 CFR-DOT, EM 385 standards, Alaska

Administrative Code (18 AAC 62) and updates thereto. The Contractor shall be responsible for all initial and refresher training required of Contractor personnel and it shall be completed in the appropriate timeframes. Upon request by the USG, the Contractor shall provide proof that these trainings were completed.

5. SEGREGATION OF WASTE

All items collected on this contract must be segregated according to the current EPA Hazardous Waste

Compatibility Chart and kept physically separate from any containers not associated with this contract until the initial TSDF is reached. The items must be so marked, that they are readily linked to this contract throughout this performance period. The Contractor may not bring other waste onsite if conducting separate contract actions in conjunction with this TO.

6. LOADING

6.1 It is the Government's responsibility to ensure that the waste being removed is readily accessible for loading by the Contractor at the time of removal. Accessible is defined in this Section as unobstructed and not requiring the movement of other containers or objects that are not scheduled for removal on the subject TO to gain access to the waste that is scheduled for removal. The USG will aid the

Contractor/Subcontractor with loading during normal hours of operation if the appropriate personnel and/or equipment are available for use and the assistance is otherwise appropriate. An offer of assistance, if accepted by the USG, will be limited to initial placement or “tailgate” of the item(s) on conveyance furnished by the Contractor. The initial placement will be as determined by the USG, after consultation with the Contractor, if necessary. Only USG employees and other authorized USG equipment operators shall operate equipment used pursuant to this paragraph. By requesting loading assistance of conveyance furnished by the Contractor, the Contractor agrees to indemnify and hold harmless the USG for any damage, incidental or otherwise, to the conveyance by the USG.

6.2 At the Government's option, the use of USG scales will be allowed. When onsite USG scales are available; weights must be agreed upon by both the Contractor and the USG before removal. When offsite commercial scales must be used, a certified weight ticket will be provided to the COR as stated above and shall be the basis for payment to the Contractor.

7. TASK ORDER (TO) ADJUSTMENTS

7.1 All TO weights and/or volumes are estimated. The Contractor can expect that the TO weights and/or volumes will require adjustment upward or downward as removals take place and the actual weights/volumes being removed are determined. Therefore, the USG has the unilateral right to increase or decrease the TO weight/volume in those cases where the USG has underestimated or overestimated the weight/volume ordered for removal, allowing the Contractor to complete the performance.

7.2 In cases of adjustments resulting in a decreased weight/volume, these decreases are not subject to

FAR 52.212-4, termination for convenience coverage. In addition, it is agreed that it is acceptable for the

USG to issue TO modifications unilaterally for quantity changes, noun description changes, CLIN changes, adding/deleting lines, extending TO end dates, etc. The Contractor will be paid for the actual items and quantities removed per the awarded contract price schedule. If upon receipt of a unilateral TO modification and the Contractor does not agree with the USG’s change(s), the Contractor reserves the right to seek resolution through the KO. These modifications pertain only to issued TOs, and no changes will be made to the terms and conditions of the contract.

8. RETURN OF SHIPPING DOCUMENTATION

8.1 At the time of removal, the Contractor shall provide the Generator/USG Representative with a complete and accurate, transporter-signed copy of each manifest that is used for the waste removal. If the

Generator/USG Representative is not present at the time of removal, the Contractor shall provide the

COR with a copy of the manifest(s).

8.2 The use of transfer facilities is authorized during transit of waste to the designated facility. A transfer facility is any transportation related facility including loading docks, parking areas, storage areas and other similar areas where shipments of hazardous waste are held during the normal course of transportation, per 40 CFR § 260.10. The Contractor will ensure that the 10-day holding time is not exceeded at any transfer facility.

8.3 If within 30 days from the removal date, the waste has not yet been received at the designated

TSDF, the Contractor shall notify the COR of the current physical location of the waste. Within 45 days from the removal date, the Contractor shall provide the COR with a facility-signed electronic copy of each manifest via email. If multiple transporters were used during transit, the Contractor shall also provide the COR with a Uniform Hazardous or Non-Hazardous Waste Manifest Continuation Sheet, as applicable, with additional transporter signatures as necessary.

8.4 If the Contractor is unable to deliver the waste to the designated or alternate facility identified on the manifest(s) per 40 CFR § 263.21(a), the COR and Generator will be contacted for disposition and manifest revision instructions per 40 CFR § 263.21(b). The Contractor shall make reasonable attempts to deliver the waste to a qualified alternate facility rather than returning the waste to the Generator. In the event of rejected shipments, or where the shipment is undeliverable, the Contractor shall provide the

Generator with a written narrative of the incident, including details of all attempts to provide delivery to a qualified TSDF. If the manifest copy cannot be provided within 45 days from the date of removal, the

Contractor shall notify the generator and COR electronically with the current location of the manifested materials and the expected date of return for the manifests.

9. CERTIFICATES OF DISPOSAL, DESTRUCTION, & RECYCLING

Certificates of Disposal/Destruction (CD) or Recycling for any/all items are required. Some facilities issue CDs or Certificates of Recycling that, in essence, state the waste “will be” versus “has been” recycled, disposed, or destroyed IAW applicable regulations. Such certificates will be authorized under this Section, but only when issued and certified by the final recycling or disposal facility.

CDs and Certificates of Recycling shall be provided to the Generator and the COR within 30 days after disposal, destruction, or recycling occurs. The Contractor will not be authorized payment until all required Certificates of Disposal/Destruction (CD) or Recycling are received by the COR and Generator.

10. GOVERNMENT PROVIDED SERVICES OR EQUIPMENT

• All material pre-packaged in DOT compliant containers

• Forklift and operator

• Pallet jack as needed

• Parking for temporary placement of a shipping container up to 40 feet long

• Signatory as the generator for any shipping documents

• Assistance with waste profiles if requested

11. CONTAINERS AND WEIGHTS

11.1 Waste located in N48 is segregated under the following characteristics. Waste located in

N102 is Non-Hazardous/Non-Regulated/Universal Waste. Safety Data Sheets or analytical data will be provided to allow for accurate profiles and shipping documentation.

Sump 1: Toxic

Sump 2: Toxic

Sump 3: Corrosive

Sump 4: Oxidizers

Sump 5: Corrosive

Sump 6: Flammable

Sump 7: Flammable

11.2 Container Inventory

Cont.ID Waste Name BLDG Location Container Size Unit LBS

22,466 Solvent Rags N48 Sump 2 DF o/t 55 Gal 59

23,641 Gasoline Rags N48 Sump 2 DF o/t 5 Gal 8

24,566 Sandblast Media, Used N48 Sump 2 DF o/t 5 Gal 54

25,045 Paint Related Waste, Cans N48 Sump 2 DF o/t 55 Gal 49

25,302 AloxGlass Sand Blast Media, Used N48 Sump 2 DF o/t 3 Gal 9

25,310 Sampling Waste, N48 N48 Sump 2 DM o/t 55 Gal 48

25,334 Scrap Metal, Lead N48 Sump 2 DF o/t 30 Gal 165

24,915 Battery, Lead Acid, Broken/Leaking N48 Sump 3 DF o/t 20 Gal 59

24,996 Suspect Sludge, Hangar 3 AFFF Tank Room N48 Sump 3 DF o/t 85 Gal 83

25,467 Pool Reagents, R-0002,5, 9 and 10 N48 Sump 3 DF o/t 1 Gal 2

25,365 Bromine Cartridges N48 Sump 4 DF o/t 10 Gal 19

21,175 Paint Slops N48 Sump 6 DM o/t 10 Gal 74

22,467 Paint Slops N48 Sump 6 DM o/t 10 Gal 40

24,254 Sampling Waste N48 Sump 6 DM o/t 55 Gal 94

24,466 Gasoline-Diesel Mixture N48 Sump 6 DM b/t 10 Gal 75

24,551 Paint Slops N48 Sump 6 DM o/t 10 Gal 45

25,071 N48 Sampling Waste N48 Sump 6 DM o/t 55 Gal 45

25,171 Paint Slops, Oil Based N48 Sump 6 DM o/t 30 Gal 97

25,181 Lacquer Thinner, Suspect N48 Sump 6 DM b/t 10 Gal 23

25,246 Amercoat T-10, 91-82 Thinner N48 Sump 6 DM o/t 30 Gal 46

25,351 Lubricant, Bonderite, Part A N48 Sump 6 DM o/t 5 Gal 16

25,352 Resin, Bonderite Solution Part B N48 Sump 6 DM o/t 5 Gal 12

25,385 Pro Sanitize Advanced - Hand Sanitizer N48 Sump 6 DM o/t 55 Gal 249

25,457 Fuel, Compressed, Trioxane Ration Heating N48 Sump 6 DM o/t 5 Gal 16

25,468 Pool Reagents N48 Sump 6 DM o/t 5 Gal 12

24,024 Gasoline-Diesel Mixture N48 Sump 7 DM b/t 55 Gal 410

25,254 Gasoline, Suspect N48 Sump 7 DM o/t 85 Gal 279

25,378 Used Oil, Solvent Contaminated N48 Sump 7 DM b/t 55 Gal 271

24,698 Strainer Debris, LOWS N102 Bay A DF o/t 5 Gal 40

25,204 U/W Aerosols, Foam N102 Bay A DF o/t 30 Gal 50

25,248 Bromine Cartridge N102 Bay A DF o/t 10 Gal 11

25,281 Batteries, Alkaline N102 Bay A DF o/t 55 Gal 59

25,290 Toilet Grit Soap N102 Bay A DF o/t 1 Gal 3

25,353 Grease, Brisal OX 50-855 N102 Bay A Bag 1 Gal 2

25,366 Fire Extinguishing Agent, Badger PKP N102 Bay A DF o/t 2.5 Gal 10

25,387 U/W Batteries, Ni-Cad N102 Bay A DF o/t 3 Gal 5

25,388 U/W Batteries, Lithium-Ion N102 Bay A DF o/t 55 Gal 33

25,458 3M Scotch-Weld Epoxy Adhesive N102 Bay A DF o/t 2.5 Gal 6

25,466 Pool Reagents, R-0001, 3, 4, 6, 7, 8, 12 and

N102 Bay A DF o/t 1 Gal 3

25,004 N1 Wash Bay Trench Sediment N102 Bay B DM o/t 55 Gal 521

25,005 N1 Wash Bay Trench Sediment N102 Bay B DM o/t 55 Gal 797

25,006 N1 Wash Bay Trench Sediment N102 Bay B DM o/t 55 Gal 850

25,007 N1 Wash Bay Trench Sediment N102 Bay B DM o/t 55 Gal 857

25,051 Motorpool Trench Sediment N102 Bay B DM o/t 55 Gal 826

25,052 Motorpool Trench Sediment N102 Bay B DM o/t 55 Gal 890

25,053 Motorpool Trench Sediment N102 Bay B DM o/t 55 Gal 875

25,147 OWS-Used Oil Sludge, Steam Plant N102 Bay B DM o/t 30 Gal 96

25,258 Diesel Contaminated Soil-Gravel N102 Bay B DM o/t 30 Gal 413

25,259 Diesel Contaminated Soil-Gravel N102 Bay B DM o/t 55 Gal 507

25,272 JP5 Contaminated Soil / N22 and Hangar 1 Fuel Pits

N102 Bay B DM o/t 55 Gal 314

25,277 OWS Sludge, Bldg 518 N102 Bay B DM o/t 30 Gal 171

25,297 OWS Sludge, Bldg 518-South N102 Bay B DM o/t 30 Gal 360

25,370 Sodium Thiosulfate Pentahydrate N102 Bay B DF o/t 55 Gal 135

25,371 Sodium Thiosulfate Pentahydrae Contaminated PPE

N102 Bay B DF o/t 30 Gal 35

24,838 Boiler Rinsate, Boiler #4 N102 Bay C IBC 275 Gal 1451

25,294 N79 Purge Water, Suspect N102 Bay C DF o/t 55 Gal 230

25,299 Purge Water, Brice Solutions, 2024 CDC Project

N102 Bay C DF o/t 55 Gal 255

25,442 ACF-50 Corrosion Resistant Lubricant N102 Bay C DF b/t 55 Gal 425

24,839 Fly Ash, Boiler #4 N102 Bay D CF 11G 1 Cyd 274

24,905 JP5-POL Contaminated Rags and Debris N102 Bay D CF 11G 1 Cyd 238

25,175 Fly Ash, Boiler #2 N102 Bay D CF 11G 1 Cyd 405

25,195 U/W Lamps, 2-4ft *Cardboard Tube* N102 Bay D DF o/t 30 Gal 140

25,234 Oily Rags N102 Bay D CF 11G 1 Cyd 441

25,242 Oily Rags N102 Bay D CF 11G 1 Cyd 348

25,243 Oily Rags N102 Bay D CF 11G 1 Cyd 387

25,244 Filters, Used Oil-Plastic N102 Bay D CF 11G 1 Cyd 278

25,261 Oily Rags and Debris N102 Bay D CF 11G 1 Cyd 209

25,282 Oily Rags N102 Bay D CF 11G 1 Cyd 348

25,293 POL Contaminated Absorbents and Debris N102 Bay D CF 11G 1 Cyd 385

25,339 U/W Lamps, 4ft *Cardboard Tube* N102 Bay D DF o/t 30 Gal 60

25,340 U/W Lamps, HID *Cardboard Tube* N102 Bay D DF o/t 30 Gal 24

25,364 Empty Containers, AFFF Contaminated, Ansul 3%

N102 Bay D CF 11G 1 Cyd 77

25,367 Filters, JP5 N102 Bay D CF 11G 1 Cyd 173

25,441 Hydraulic Fluid Contaminated Absorbents and Debris

N102 Bay D CF 11G 1 Cyd 440

25,422 Engine Coolant, Zerex G-93 N102 Bay C DF o/t 15 Gal 121

25,159 Non-Haz Paint Related Waste N102 Bay F DM o/t 5 Gal 12

25,232 AFFF, Ansulite-3 AFC-3A HWSB Locker 9 DF o/t 55 Gal 155

25,233 AFFF, Ansulite-3 AFC-3A HWSB Locker 9 DF o/t 55 Gal 375

25,295 AFFF, Ansulite3% - AFC3A HWSB Locker 9 DF b/t 55 Gal 436

25,323 Ansulite-3, AFC 3A, AFFF HWSB Locker 9 DF b/t 55 Gal 443

24,972 H/W Pharmaceuticals, Aerosol N46 Pharmacy DF o/t 1 Gal 5 25,088 H/W Pharmaceuticals N46 Pharmacy DF o/t 5 Gal 10