3_Quality_Assurance_Letter_of_Instruction.pdf
PDF 907 KB Posted
- Attached to
- THRUSTER, CARTRIDGE ACTUATED Federal contract opportunity
- Solicitation number
- FA8213-20-R-0009
About this file
This quality assurance letter of instruction outlines inspection requirements for a federal contract to produce cartridge actuated thrusters. The contractor must impose mandatory, witness, verification, and monitor inspection points into work orders for critical flight items. Inspection requirements include explosive weight verification, leak testing, x-ray inspection, life and acceleration testing, ammunition data card review, preparation for shipment, and additional requirements as deemed necessary by the Defense Contract Management Agency. The contract was awarded on an unspecified date for final delivery by 12/16/2020 to produce thruster cartridges described as aluminum, 10-inch nominal size, 3.5-inch shipping container for the F-15 program under contract number 20-50009 with Nammo Talley.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| 1_Airmunition_Specification.docx | DOCX document | |
| 4_ES7034_Rework_and_Repair_of_Nonconforming_Material.doc | DOC document | |
| 5_REPSHIP_of_HAZMAT.doc | DOC document | |
| 11_Item_Description.pdf | ||
| Request For Proposal FA8213-20-R-0009.pdf | ||
| 2_Statement_of_Work_Ammunition_Data_Card.doc | DOC document | |
| 6_Report_of_Shipment.pdf | ||
| 8_Contract_Data_Requirements_List.pdf | ||
| 9_AFMC_Form_158_Packaging_Requirements.pdf | ||
| 12_Engineering_Data_List.pdf | ||
| 13_Bid_Sets.doc | DOC document | |
| 16_Section_M_Lowest_Price.docx | DOCX document | |
| 14_JFQR_1377-00-313-4761ES_F-15_ARR_Thruster).pdf | ||
| 7_CADPAD_Item_Marking.pdf | ||
| 10_SOW_for_Packaging_and_Preservation.pdf | ||
| 15_Section_L_Lowest_Price.docx | DOCX document |
Show all 16
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Contractor Name CAGE code
DCMA QAR Reviewer
Date Review Completed
Date Issued to Contractor
PR No. FD2020-
Date Contract Awarded
Final Delivery Date (FDD)
Program Name
DODIC
Part Number
The contractor is required to impose the listed below DCMA Inspection Points into the appropriate Work Orders.
All Work Orders pertaining to CRITICAL FLIGHT ITEMS must be identified on folders.
Mandatory - M: Stamp and/ or Signature on original documentation (i.e., Mfg. Planning, ATP, FAT Report, etc.)
Witness - W: GSI required to attend, may reduce level of effort after 50% of production lots found acceptable Verification - V: Stamp and/or Signature required unless noted otherwise (may be done by written verification) Monitor - R: Will monitor testing, may reduce to verification Notify - N: By phone or daily schedule 24( R ) - 48 ( NR ) hours in advance
Additional requirements: (DCMA reserves the right to impose additional inspection points as deemed necessary.)
Prepared by:
Date
Concurrence Signature by QAR/DCMA:
QAR/DCMA Signature
THIS PLANNING SHEET WILL BE UPDATED IF NECESSARY.
QUALITY ASSURANCE LETTER OF INSTRUCTION
Planning Requirements
COMMENTS
NOTICE
Engineer Signature
Date
Rev Date: 30 Apr 2019
Sheet1
| Text49: | |
| Text46: 21 Oct 2019 | |
| 2019-05-02T10:47:03-0600 | |
| TIDWELL.QUINN.RAY.1241451913 |
| undefined_9: N |
| Text32: 9. Additional Requirements |
| undefined_8: M |
| Text31: 8. Shippers (DD250, DD1149, Reports) |
| undefined_7: |
| Text30: 7. AMMO Data Card Review |
| undefined_6: V |
| Text29: 6. Preparation for Shipment |
| undefined_5: V |
| Text28: 5. LAT |
| undefined_4: V |
| Text27: 4. LAT Sample Selection |
| undefined_3: V |
| Text26: 3. X-Ray/N-Ray |
| undefined_2: |
| Text25: 2. Leak Test |
| undefined: |
| Text36: 1. Explosive Weight |
2. Verify gross leak and fine leak check are performed.
3. Ensure film labeling correct. Ensure radiographic film is readable and well-defined. DCMA is not required to interpret film.
4. Randomly select LAT units per latest government approved ATP. Prior to LAT ensure proper calibration and validation of all test equipment.
5. Testing should occur in accordance with latest government approved ATP. Witness proper test setup and at least the first 3 functional tests. Further witness may be required if there are known concerns with the item or requested by Government Engineer.
6. Ensure Paperwork is correct.
7. Verify all energetic materials: list original manufacturer,original lot number, and latest certification/recertification date < 24 months.
8. Ensure Paperwork is correct. Verify Packaging, Packing, Preservation & Marking (PPP&M)
9. Any additional requirements imposed by DCMA shall be approved by Government Project Engineer
| Text24: 1.Inspection |
| Part Number: 30351-9 |
| Text23: |
| DODIC: MC57 |
| Text22: |
| Text21: |
| Text20: 12116 |
| Text19: Nammo Talley |
| Part Number Line 2: |
| Contract No: 20-50009 |
| Date Contract Awarded: |
| Final Delivery Date FDD: |
| Program Name: F-15 |
File details come from the government source that posted it. Updated .