Aircraft Wheel Washer

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. This solicitation W9127Q-18-R-0033, is being issued as a Request for Proposal (RFP). This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular (FAC) 2005-101. This requirement is 100% set-aside for small business. The NAICS code is 333249 and the small business size standard is 500 Employees.

This requirement is for a StingRay 3032 Aircraft Wheel Washer. All items must be new. Prototypes, demonstration models, used, or refurbished equipment will not be considered for award. All items requested will accept an OR EQUAL item.

Standard Features & General Construction

Green Technology:

Stainless Steel Cabinet & Wetted Standard Components

Heavy gage Sheet Cabinet Thickness

Pump with Stainless Steel Shafts, Fasteners and Viton Seals

Auto Fresh Water Rinse Cycle

Auto Steam Exhaust System

Auto Programmable Oil Skimmer System

Engineered Wheel Wash Power Blast Manifold

Oscillating Wash Manifold to Maximize Cleaning

1 Station Aircraft Wheel Fixture fits most wheel sizes

Removable Internal Reservoir Cover allows Full Access to machine reservoir

Swing Door Retracting Turntable for Maximum Access

Electronic Water Level Control & Refill

Easy to Service Front Wash Pump Suction Strainer

Adjustable Electronic Digital Temp Control, 2 line display present value & set-point

Control Transformer External of Panel minimizes Heat

Programmable 24 Hour 7 Day Clock

Low Water Shut-off Protects Pumps & Heating System

Electronic Door Safety Interlock

Wash Cycle Timer with Auto Reset

460 V - 60 Hz 3-Phase with 120 V Controls Standard

208 VAC or 575 VAC optional

International 50 Hz upgrades for 380, 400, 415 VAC

Chemical Resistant Two Part 3 mil Epoxy Coating

Technical Requirements:

• 30" to 40" turntable and 30" to 40" work height designated Aircraft Wheel Washer with custom manifold system for removing rubber bead from wheels

• Swing door with door mounted turntable that automatically retracts when door is opened

• Turntable Height above Floor: 20" - 40"

• Stainless Steel Cabinet

• 30 kW of electric heat minimum at 460 V 60 Hz.

• Oscillating Power Blast Manifold non-synchronous to the turntable

• Wash load will be blasted from a different angle of impingement with each pass by the nozzles.

• Minimum 30 hp Pump System

• Minimum 30 hp pump has a total system flow of a minimum of 250gpm, with a system pressure of a minimum of 150 psi at the PUMP and at blast velocity of a minimum of 140 fUsec.

• Quick-load Non-scarring Main and Nose Wheel Fixtures designed for specific wheels

• Heated Fresh Water Rinse System.

• Operating Temperature 160-195 degrees

• Wash Pump Suction Strainer

• 10" to 18" Stainless Steel Oil Skimmer

• Remote Grease Fitting SS for PBM Swivel

• Reservoir Capacity must be 100 gallons Minimum

• Sludge Capacity must be 30 gallons Minimum

• Programmable Dual Channel 24 hour - 7 day Programmable Clock

• Electronic Door Safety Interlock

• Wash Cycle Timer with reset function

• Automatic Water Level Control & Refill

• Adjustable Electronic Temperature Control with stainless steel thermocouple

• Low Water Shut-Off

• Removable Internal Reservoir Cover

• Electrical System to meet NFPA 79, includes Safety Power Disconnect, Hour Meter, Turntable Jog, Lifting Lugs, Drain and Clock Override

• Operating/Maintenance Manual and not cut sheets

• Site Training

• Freight to Military Facility

Wheel Washer will be required to come with a Steam Exhaust PVC Kit w/ Swivel Flanges & Fasteners; and Maintenance Kit, and Touch-up Paint.

Government will provide the following:

1. Electrical power supply to wall-mount NEMA rated non-fused disconnect within 15 feet of equipment location with up to 100A at 480V.

2. 1" water supply with backflow apparatus and pressure regulator with 1" full port valve (sweat connection).

3. 120V power for tools used during equipment setup.

Contractor will be responsible for the following:

1. Delivery, unloading, uncrating/unpackaging, erection, and placement of the equipment. Contractor will be required to provide any and all tools, equipment, etc.

2. Connection of electrical service from Gov-provided disconnect to the equipment.

3. Connection of water service from 1" full port valve (sweated) to the equipment.

4. All start-up, troubleshooting, and training of machine.

5. Delivery of warranty, O & M Manuals, and any extra parts.

Equipment must be capable of installation in an area no larger than 120" wide, 140" long, and 83" tall to include any allowances for clearances, walkways, equipment maintenance and repair, and ventilation as necessary.

Equipment must have a waste tank or reservoir for waste water with a minimum volume of 100 gallons and must not require a piped drainage system. Drainage will be performed manually. A drainage port with valve is preferred on the reservoir but not required.

Items must meet the technical requirements to be considered for award.

Evaluation - Commercial Items: the Government will award a contract resulting from this solicitation to the responsible offeror whose proposal conforming to the solicitation will be most advantageous to the Government, price and technical considered. The following factor shall be used to evaluate offers: Lowest Price Technically Acceptable (LPTA).

All responsible sources may submit a quote, which will be considered by the Government. Award will be made to the offeror whose quote conforms to the solicitation technical requirements and is able to satisfy the Government's requirements.

1. Price: The Government will evaluate offers based on the total price for the basic requirement. To evaluate price reasonableness, a comparison will be made amongst all received proposals and the Government's estimate.

2. Technical Qualification: A vendor's proposal will be evaluated on technical acceptance. Proposals that do not meet technical requirements will be considered unacceptable and therefore, under the LPTA evaluation process will not be considered for award.

To be rated as Technically Acceptable, the quote must either be for the brand name product specified above or be for an equivalent product. "Or equal" items shall be comparable with the minimum salient characteristics as listed in under Standard Features and Technical Requirements and shall be determined technically acceptable by the Government prior to award. Furthermore, the requirement must be delivered no later than 120 days after date of contract.

Table 1. Technical Ratings Rating Description

Rating

Description

Acceptable

Acceptable Proposal clearly meets the minimum requirements of the solicitation.

Unacceptable

Unacceptable Proposal does not clearly meet the minimum requirements of the solicitation.

Technical Ratings Rating Description Acceptable Proposal clearly meets the minimum requirements of the solicitation. Unacceptable Proposal does not clearly meet the minimum requirements of the solicitation.

All interested and qualified small business sources are encouraged to submit

a quote, which shall be considered by the agency. Period of acceptance for

Offerors: The offeror agrees to hold its offer firm for 30 calendar days form

the date specified for receipt of offers, unless another time period is stated in

an addendum to the solicitation. Late offers: Request for Proposals of

modification of proposals received at the address specified for the receipt of

offers after the exact time specified for receipt of offers will be handled in

accordance with FAR 52.212-1(f).

The Government reserves the right to cancel this solicitation, either before or

after the closing date. In the event the Government cancels this solicitation,

the Government has no obligation to reimburse an offeror for any costs.

The following provisions and clauses apply to this acquisition: The provision

at FAR 52.212-1, Instructions to Offerors--Commercial Items. The provision at

FAR 52.212-3, Offeror Representations and Certifications -- Commercial

Items, and the offeror must include a completed copy of this provision with

their proposal. The clause at FAR 52.212-4, Contract Terms and Conditions-

Commercial Items; FAR 52.212-5, Contract Terms and Conditions Required

To Implement Statutes or Executive Orders--Commercial Items. Specifically,

the following clauses cited are applicable to this solicitation: FAR 52.204-10

Reporting Executive Compensation and First-Tier subcontract Awards, FAR

52.219-28, Post-Award Small Business Program Repesentation; FAR 52.222-

21, Prohibition of Segregated facilities; FAR 52.225-13, Restrictions on

Certain Foreign Purchases; FAR 52.233-3 Protest After Award; FAR 52.233-

4, Applicable Law for Breach of Contract Claim; FAR 52.222-3, Convict

Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies;

FAR 52.222-26, Equal Opportunity; FAR 52.222-35, Affirmative Action for

Disabled Veterans and Veterans of the Vietnam Era; FAR 52.222-36,

Affirmative Action for Handicapped Workers; FAR 52.222-37, Employment

Reports on Disabled Veterans and Veterans of the Vietnam Era. The clause at FAR 52.224-1, Privacy Act Notification and FAR 52.224-2, Privacy Act; FAR

52.232-33, Payment by Electronic Funds-Central Contractor Registration;

DFARS 252.209-7993 (Dev); FAR 52.222-99. The clause at DFARS 252.204-

7004, Required Central Contractor Registration; DFARS 252.212-7001,

Contract Terms and Conditions Required to Implement Statues or Executive

Orders; Full text of these clauses may be accessed on-line at

http://www.arnet.gov or http;//farsite.hill.af.mil.

This announcement is the solicitation which will result in a firm fixed price

contract. The Government reserves the right to award on a multiple

award or an all or none basis. All firms must be registered in the System of

Acquisition Management database @ www.sam.gov and shall be considered

for award. SAM is a mandatory requirement for all DOD Government

contracts. You must be registered in order to be eligible for award of a

contract. All quotes must be sent to SrA Jared Garner at: Fax 601-484

-9087; e-mail jared.a.garner2.mil@mail.mil; or mail directly to 186th ARW,

6225 M Street, Meridian, MS 39307-7112. Quotes are required to be received

not later than 3:30 PM CST, Friday, 17 September, 2018.

POINTS OF CONTACT; Technical questions regarding this

requirement may be addressed to SrA Jared Garner at

jared.a.garner2.mil@mail.mil. Contracting questions for this requirement

may be addressed to SrA Jared Garner at jared.a.garner2.mil@mail.mil.

.

This is a combined synopsis/solicitation for commercial items prepared in

accordance with the format in Subpart 12.6, as supplemented with additional

information included in this notice. This announcement constitutes the only

solicitation; proposals are being requested and a written solicitation will not be

issued. This solicitation W9127Q-18-R-0033, is being issued as a Request for

Proposal (RFP). This solicitation document and incorporated provisions and

clauses are those in effect through Federal Acquisition Circular (FAC) 2005-

101. This requirement is 100% set-aside for small business. The NAICS code

is 333249 and the small business size standard is 500 Employees.

This requirement is for a StingRay 3032 Aircraft Wheel Washer. All items must be new. Prototypes, demonstration models, used, or refurbished equipment will not be considered for award. All items requested will accept an OR EQUAL item.

USA Specifications:

SR 3032
Parts Washer

Metric Specifications:

SR 3032
Parts Washer

Standard Features & General Construction

Green Technology: Closed Loop Zero Discharge & High Efficiency
Stainless Steel Cabinet & Wetted Standard Components
Heavy gage Sheet Cabinet Thickness
Pump with Stainless Steel Shafts, Fasteners and Viton Seals
Auto Fresh Water Rinse Cycle
Auto Steam Exhaust System
Auto Programmable Oil Skimmer System
Engineered Wheel Wash Power Blast Manifold
Oscillating Wash Manifold to Maximize Cleaning
1 Station Aircraft Wheel Fixture fits most wheel sizes
Removable Internal Reservoir Cover allows Full Access to machine reservoir
Swing Door Retracting Turntable for Maximum Access
Electronic Water Level Control & Refill
Easy to Service Front Wash Pump Suction Strainer
Adjustable Electronic Digital Temp Control, 2 line display present value & set-point
Control Transformer External of Panel minimizes Heat
Programmable 24 Hour 7 Day Clock
Low Water Shut-off Protects Pumps & Heating System
Electronic Door Safety Interlock
Wash Cycle Timer with Auto Reset
460 V - 60 Hz 3-Phase with 120 V Controls Standard
208 VAC or 575 VAC optional
International 50 Hz upgrades for 380, 400, 415 VAC
Chemical Resistant Two Part 3 mil Epoxy Coating

Technical Requirments:

• 30" to 40" turntable and 30" to 40" work height designated Aircraft Wheel Washer with custom manifold system for removing rubber bead from wheels
• Swing door with door mounted turntable that automatically retracts when door is opened
• Turntable Height above Floor: 20" - 40"
• Stainless Steel Cabinet
• 30 kW of electric heat minimum at 460 V 60 Hz.
• Oscillating Power Blast Manifold non-synchronous to the turntable
• Wash load will be blasted from a different angle of impingement with each pass by the nozzles.
• Minimum 30 hp Pump System
• Minimum 30 hp pump has a total system flow of a minimum of 250gpm, with a system pressure of a minimum of 150 psi at the PUMP and at blast velocity of a minimum of 140 fUsec.
• Quick-load Non-scarring Main and Nose Wheel Fixtures designed for specific wheels
• Heated Fresh Water Rinse System.
• Operating Temperature 160-195 degrees
• Wash Pump Suction Strainer
• 10" to 18" Stainless Steel Oil Skimmer
• Remote Grease Fitting SS for PBM Swivel
• Reservoir Capacity must be 100 gallons Minimum
• Sludge Capacity must be 30 gallons Minimum
• Programmable Dual Channel 24 hour - 7 day Programmable Clock
• Electronic Door Safety Interlock
• Wash Cycle Timer with reset function
• Automatic Water Level Control & Refill
• Adjustable Electronic Temperature Control with stainless steel thermocouple
• Low Water Shut-Off
• Removable Internal Reservoir Cover
• Closed Loop Zero Discharge - no wash water or rinse water shall discharge machine.
• Electrical System to meet NFPA 79, includes Safety Power Disconnect, Hour Meter, Turntable Jog, Lifting Lugs, Drain and Clock Override
• Operating/Maintenance Manual and not cut sheets
• Site Training
• Freight to Military Facility

Wheel Washer will be required to come with a Steam Exhaust PVC Kit w/ Swivel Flanges & Fasteners; and Maintenance Kit, and Touch-up Paint.

Installation of wheel washer will need to be included in quote.

No water lines will be created to supply system with water. System will need to have capability to have water and detergent manually added by personnel. No drain lines will be added to facilty to drain system. System must have capability to be manually drained by personnel.

Items must meet the technical requirements and include required additional parts to be considered for award.

All interested and qualified small business sources are encouraged to submit
a quote, which shall be considered by the agency. Period of acceptance for
Offerors: The offeror agrees to hold its offer firm for 30 calendar days form
the date specified for receipt of offers, unless another time period is stated in
an addendum to the solicitation. Late offers: Request for Proposals of
modification of proposals received at the address specified for the receipt of
offers after the exact time specified for receipt of offers will be handled in
accordance with FAR 52.212-1(f).
The Government reserves the right to cancel this solicitation, either before or
after the closing date. In the event the Government cancels this solicitation,
the Government has no obligation to reimburse an offeror for any costs.
The following provisions and clauses apply to this acquisition: The provision
at FAR 52.212-1, Instructions to Offerors--Commercial Items. The provision at
FAR 52.212-3, Offeror Representations and Certifications -- Commercial
Items, and the offeror must include a completed copy of this provision with
their proposal. The clause at FAR 52.212-4, Contract Terms and Conditions-
Commercial Items; FAR 52.212-5, Contract Terms and Conditions Required
To Implement Statutes or Executive Orders--Commercial Items. Specifically,
the following clauses cited are applicable to this solicitation: FAR 52.204-10
Reporting Executive Compensation and First-Tier subcontract Awards, FAR
52.219-28, Post-Award Small Business Program Repesentation; FAR 52.222-
21, Prohibition of Segregated facilities; FAR 52.225-13, Restrictions on
Certain Foreign Purchases; FAR 52.233-3 Protest After Award; FAR 52.233-
4, Applicable Law for Breach of Contract Claim; FAR 52.222-3, Convict
Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies;
FAR 52.222-26, Equal Opportunity; FAR 52.222-35, Affirmative Action for
Disabled Veterans and Veterans of the Vietnam Era; FAR 52.222-36,
Affirmative Action for Handicapped Workers; FAR 52.222-37, Employment
Reports on Disabled Veterans and Veterans of the Vietnam Era. The clause at FAR 52.224-1, Privacy Act Notification and FAR 52.224-2, Privacy Act; FAR
52.232-33, Payment by Electronic Funds-Central Contractor Registration;
DFARS 252.209-7993 (Dev); FAR 52.222-99. The clause at DFARS 252.204-
7004, Required Central Contractor Registration; DFARS 252.212-7001,
Contract Terms and Conditions Required to Implement Statues or Executive
Orders; Full text of these clauses may be accessed on-line at
http://www.arnet.gov or http;//farsite.hill.af.mil.
This announcement is the solicitation which will result in a firm fixedprice
contract. The Government reserves the right to award on a multiple
award or an all or none basis. All firms must be registered in the System of
Acquisition Management database @ www.sam.gov and shall be considered
for award. SAM is a mandatory requirement for all DOD Government
contracts. You must be registered in order to be eligible for award of a
contract. All quotes must be sent to SrA Jared Garner at: Fax 601-484
-9087; e-mail jared.a.garner2.mil@mail.mil; or mail directly to 186th ARW,
6225 M Street, Meridian, MS 39307-7112. Quotes are required to be received
not later than 3:30 PM CST, Friday, 17 September, 2018.
POINTS OF CONTACT; Technical questions regarding this
requirement may be addressed to SrA Jared Garner at
jared.a.garner2.mil@mail.mil. Contracting questions for this requirement
may be addressed to SrA Jared Garner at jared.a.garner2.mil@mail.mil.

RFQ is being extended with more changes to come shortly.

.

This is a combined synopsis/solicitation for commercial items prepared in

accordance with the format in Subpart 12.6, as supplemented with additional

information included in this notice. This announcement constitutes the only

solicitation; proposals are being requested and a written solicitation will not be

issued. This solicitation W9127Q-18-R-0033, is being issued as a Request for

Proposal (RFP). This solicitation document and incorporated provisions and

clauses are those in effect through Federal Acquisition Circular (FAC) 2005-

101. This requirement is 100% set-aside for small business. The NAICS code

is 333249 and the small business size standard is 500 Employees.

This requirement is for a StingRay 3032 Aircraft Wheel Washer. All items must be new. Prototypes, demonstration models, used, or refurbished equipment will not be considered for award. All items requested will accept an OR EQUAL item.

USA Specifications:

SR 3032
Parts Washer

Metric Specifications:

SR 3032
Parts Washer

Standard Features & General Construction

Green Technology: Closed Loop Zero Discharge & High Efficiency
Stainless Steel Cabinet & Wetted Standard Components
Heavy gage Sheet Cabinet Thickness
Pump with Stainless Steel Shafts, Fasteners and Viton Seals
Auto Fresh Water Rinse Cycle
Auto Steam Exhaust System
Auto Programmable Oil Skimmer System
Engineered Wheel Wash Power Blast Manifold
Oscillating Wash Manifold to Maximize Cleaning
1 Station Aircraft Wheel Fixture fits most wheel sizes
Removable Internal Reservoir Cover allows Full Access to machine reservoir
Swing Door Retracting Turntable for Maximum Access
Electronic Water Level Control & Refill
Easy to Service Front Wash Pump Suction Strainer
Adjustable Electronic Digital Temp Control, 2 line display present value & set-point
Control Transformer External of Panel minimizes Heat
Programmable 24 Hour 7 Day Clock
Low Water Shut-off Protects Pumps & Heating System
Electronic Door Safety Interlock
Wash Cycle Timer with Auto Reset
460 V - 60 Hz 3-Phase with 120 V Controls Standard
208 VAC or 575 VAC optional
International 50 Hz upgrades for 380, 400, 415 VAC
Chemical Resistant Two Part 3 mil Epoxy Coating

Technical Requirments:

• 30" to 40" turntable and 30" to 40" work height designated Aircraft Wheel Washer with custom manifold system for removing rubber bead from wheels
• Swing door with door mounted turntable that automatically retracts when door is opened
• Turntable Height above Floor: 20" - 40"
• Stainless Steel Cabinet
• 30 kW of electric heat minimum at 460 V 60 Hz.
• Oscillating Power Blast Manifold non-synchronous to the turntable
• Wash load will be blasted from a different angle of impingement with each pass by the nozzles.
• Minimum 30 hp Pump System
• Minimum 30 hp pump has a total system flow of a minimum of 250gpm, with a system pressure of a minimum of 150 psi at the PUMP and at blast velocity of a minimum of 140 fUsec.
• Quick-load Non-scarring Main and Nose Wheel Fixtures designed for specific wheels
• Heated Fresh Water Rinse System.
• Operating Temperature 160-195 degrees
• Wash Pump Suction Strainer
• 10" to 18" Stainless Steel Oil Skimmer
• Remote Grease Fitting SS for PBM Swivel
• Reservoir Capacity must be 100 gallons Minimum
• Sludge Capacity must be 30 gallons Minimum
• Programmable Dual Channel 24 hour - 7 day Programmable Clock
• Electronic Door Safety Interlock
• Wash Cycle Timer with reset function
• Automatic Water Level Control & Refill
• Adjustable Electronic Temperature Control with stainless steel thermocouple
• Low Water Shut-Off
• Removable Internal Reservoir Cover
• Closed Loop Zero Discharge - no wash water or rinse water shall discharge machine.
• Electrical System to meet NFPA 79, includes Safety Power Disconnect, Hour Meter, Turntable Jog, Lifting Lugs, Drain and Clock Override
• Operating/Maintenance Manual and not cut sheets
• Site Training
• Freight to Military Facility

Wheel Washer will be required to come with a Steam Exhaust PVC Kit w/ Swivel Flanges & Fasteners; and Maintenance Kit, and Touch-up Paint.

Installation of wheel washer will need to be included in quote.

No water lines will be created to supply system with water. System will need to have capability to have water and detergent manually added by personnel. No drain lines will be added to facilty to drain system. System must have capability to be manually drained by personnel.

Items must meet the technical requirements and include required additional parts to be considered for award.

All interested and qualified small business sources are encouraged to submit
a quote, which shall be considered by the agency. Period of acceptance for
Offerors: The offeror agrees to hold its offer firm for 30 calendar days form
the date specified for receipt of offers, unless another time period is stated in
an addendum to the solicitation. Late offers: Request for Proposals of
modification of proposals received at the address specified for the receipt of
offers after the exact time specified for receipt of offers will be handled in
accordance with FAR 52.212-1(f).
The Government reserves the right to cancel this solicitation, either before or
after the closing date. In the event the Government cancels this solicitation,
the Government has no obligation to reimburse an offeror for any costs.
The following provisions and clauses apply to this acquisition: The provision
at FAR 52.212-1, Instructions to Offerors--Commercial Items. The provision at
FAR 52.212-3, Offeror Representations and Certifications -- Commercial
Items, and the offeror must include a completed copy of this provision with
their proposal. The clause at FAR 52.212-4, Contract Terms and Conditions-
Commercial Items; FAR 52.212-5, Contract Terms and Conditions Required
To Implement Statutes or Executive Orders--Commercial Items. Specifically,
the following clauses cited are applicable to this solicitation: FAR 52.204-10
Reporting Executive Compensation and First-Tier subcontract Awards, FAR
52.219-28, Post-Award Small Business Program Repesentation; FAR 52.222-
21, Prohibition of Segregated facilities; FAR 52.225-13, Restrictions on
Certain Foreign Purchases; FAR 52.233-3 Protest After Award; FAR 52.233-
4, Applicable Law for Breach of Contract Claim; FAR 52.222-3, Convict
Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies;
FAR 52.222-26, Equal Opportunity; FAR 52.222-35, Affirmative Action for
Disabled Veterans and Veterans of the Vietnam Era; FAR 52.222-36,
Affirmative Action for Handicapped Workers; FAR 52.222-37, Employment
Reports on Disabled Veterans and Veterans of the Vietnam Era. The clause at FAR 52.224-1, Privacy Act Notification and FAR 52.224-2, Privacy Act; FAR
52.232-33, Payment by Electronic Funds-Central Contractor Registration;
DFARS 252.209-7993 (Dev); FAR 52.222-99. The clause at DFARS 252.204-
7004, Required Central Contractor Registration; DFARS 252.212-7001,
Contract Terms and Conditions Required to Implement Statues or Executive
Orders; Full text of these clauses may be accessed on-line at
http://www.arnet.gov or http;//farsite.hill.af.mil.
This announcement is the solicitation which will result in a firm fixedprice
contract. The Government reserves the right to award on a multiple
award or an all or none basis. All firms must be registered in the System of
Acquisition Management database @ www.sam.gov and shall be considered
for award. SAM is a mandatory requirement for all DOD Government
contracts. You must be registered in order to be eligible for award of a
contract. All quotes must be sent to SrA Jared Garner at: Fax 601-484
-9087; e-mail jared.a.garner2.mil@mail.mil; or mail directly to 186th ARW,
6225 M Street, Meridian, MS 39307-7112. Quotes are required to be received
not later than 3:30 PM CST, Friday, 7 September, 2018.
POINTS OF CONTACT; Technical questions regarding this
requirement may be addressed to SrA Jared Garner at
jared.a.garner2.mil@mail.mil. Contracting questions for this requirement
may be addressed to SrA Jared Garner at jared.a.garner2.mil@mail.mil.

.

This is a combined synopsis/solicitation for commercial items prepared in

accordance with the format in Subpart 12.6, as supplemented with additional

information included in this notice. This announcement constitutes the only

solicitation; proposals are being requested and a written solicitation will not be

issued. This solicitation W9127Q-18-R-0033, is being issued as a Request for

Proposal (RFP). This solicitation document and incorporated provisions and

clauses are those in effect through Federal Acquisition Circular (FAC) 2005-

101. This requirement is 100% set-aside for small business. The NAICS code

is 333249 and the small business size standard is 500 Employees.

This requirement is for a StingRay 3032 Aircraft Wheel Washer. All items must be new. Prototypes, demonstration models, used, or refurbished equipment will not be considered for award. All items requested will accept an OR EQUAL item.

USA Specifications:

SR 3032
Parts Washer

Metric Specifications:

SR 3032
Parts Washer

Standard Features & General Construction

Green Technology: Closed Loop Zero Discharge & High Efficiency
Stainless Steel Cabinet & Wetted Standard Components
Heavy gage 3/16" Sheet Cabinet Thickness
Pump with Stainless Steel Shafts, Fasteners and Viton Seals
Auto Fresh Water Rinse Cycle
Auto Steam Exhaust System
Auto Programmable Oil Skimmer System
Engineered Wheel Wash Power Blast Manifold
Oscillating Wash Manifold to Maximize Cleaning
1 Station Aircraft Wheel Fixture fits most wheel sizes
Removable Internal Reservoir Cover allows Full Access to machine reservoir
Swing Door Retracting Turntable for Maximum Access
Electronic Water Level Control & Refill
Easy to Service Front Wash Pump Suction Strainer
Adjustable Electronic Digital Temp Control, 2 line display present value & set-point
Control Transformer External of Panel minimizes Heat
Programmable 24 Hour 7 Day Clock
Low Water Shut-off Protects Pumps & Heating System
Electronic Door Safety Interlock
Wash Cycle Timer with Auto Reset
460 V - 60 Hz 3-Phase with 120 V Controls Standard
208 VAC or 575 VAC optional
International 50 Hz upgrades for 380, 400, 415 VAC
Chemical Resistant Two Part 3 mil Epoxy Coating

Technical Requirments:

• 30" turntable and 32" work height designated Aircraft Wheel Washer with custom manifold system for removing rubber bead from wheels
• Swing door with door mounted turntable that automatically retracts when door is opened
• Turntable Height above Floor: 29.5
• Heavy 7 gauge 3/16" 304 Stainless Steel Cabinet Thickness
• 30 kW of electric heat minimum at 460 V 60 Hz.
• Oscillating Power Blast Manifold non-synchronous to the turntable at 39 degrees of angle of oscillation with a frequency of oscillation at 4 per minute. Blasts shall be non-intersecting with off-set upper and lower arms.
• Wash load will be blasted from a different angle of impingement with each pass by the nozzles.
• 30 hp Pump System with Viton Seals for use with McGean's CEEBEE Detergent
• 30 hp pump has a total system flow of 256 gpm, with 13.8 gpm flow per nozzle and a system pressure of 152 psi at the PUMP and at blast velocity of 150 fUsec.
• Quick-load Non-scarring Main and Nose Wheel Fixtures designed for specific wheels
• Heated Fresh Water Rinse System.
• Operating Temperature 160-195 degrees
• Wash Pump Suction Strainer located in the front of the washer for easy maintenance
• 16 nozzle 316 stainless steel 25 degree V jet nozzles.
• 14" Stainless Steel Oil Skimmer
• Remote Grease Fitting SS for PBM Swivel
• Reservoir Capacity must be 130 gallons Minimum
• Sludge Capacity must be 37 gallons Minimum
• Programmable Dual Channel 24 hour - 7 day Programmable Clock
• Electronic Door Safety Interlock
• Wash Cycle Timer with reset function
• Automatic Water Level Control & Refill
• Adjustable Electronic Temperature Control with stainless steel thermocouple
• Low Water Shut-Off
• Removable Internal Reservoir Cover
• Closed Loop Zero Discharge - no wash water or rinse water shall discharge machine.
• Electrical System to meet NFPA 79, includes Safety Power Disconnect, Hour Meter, Turntable Jog, Lifting Lugs, Drain and Clock Override
• Two-Part Epoxy Coating Minimum 3.5 mil Thick w/ Acid Etch Primer
• Operating/Maintenance Manual and not cut sheets
• Site Training
• Freight to Military Facility

Wheel Washer will be required to come with a Parts Basket (20"X20"X16") w/ Lid and Latch; Steam Exhaust PVC Kit w/ Swivel Flanges & Fasteners; and Maintenance Kit w/ Suction Screen Brush, Bearing Grease, 2 Guns, Blue Touch-up Paint.

Items must meet the technical requirements and include required additional parts to be considered for award.

All interested and qualified small business sources are encouraged to submit
a quote, which shall be considered by the agency. Period of acceptance for
Offerors: The offeror agrees to hold its offer firm for 30 calendar days form
the date specified for receipt of offers, unless another time period is stated in
an addendum to the solicitation. Late offers: Request for Proposals of
modification of proposals received at the address specified for the receipt of
offers after the exact time specified for receipt of offers will be handled in
accordance with FAR 52.212-1(f).
The Government reserves the right to cancel this solicitation, either before or
after the closing date. In the event the Government cancels this solicitation,
the Government has no obligation to reimburse an offeror for any costs.
The following provisions and clauses apply to this acquisition: The provision
at FAR 52.212-1, Instructions to Offerors--Commercial Items. The provision at
FAR 52.212-3, Offeror Representations and Certifications -- Commercial
Items, and the offeror must include a completed copy of this provision with
their proposal. The clause at FAR 52.212-4, Contract Terms and Conditions-
Commercial Items; FAR 52.212-5, Contract Terms and Conditions Required
To Implement Statutes or Executive Orders--Commercial Items. Specifically,
the following clauses cited are applicable to this solicitation: FAR 52.204-10
Reporting Executive Compensation and First-Tier subcontract Awards, FAR
52.219-28, Post-Award Small Business Program Repesentation; FAR 52.222-
21, Prohibition of Segregated facilities; FAR 52.225-13, Restrictions on
Certain Foreign Purchases; FAR 52.233-3 Protest After Award; FAR 52.233-
4, Applicable Law for Breach of Contract Claim; FAR 52.222-3, Convict
Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies;
FAR 52.222-26, Equal Opportunity; FAR 52.222-35, Affirmative Action for
Disabled Veterans and Veterans of the Vietnam Era; FAR 52.222-36,
Affirmative Action for Handicapped Workers; FAR 52.222-37, Employment
Reports on Disabled Veterans and Veterans of the Vietnam Era. The clause at FAR 52.224-1, Privacy Act Notification and FAR 52.224-2, Privacy Act; FAR
52.232-33, Payment by Electronic Funds-Central Contractor Registration;
DFARS 252.209-7993 (Dev); FAR 52.222-99. The clause at DFARS 252.204-
7004, Required Central Contractor Registration; DFARS 252.212-7001,
Contract Terms and Conditions Required to Implement Statues or Executive
Orders; Full text of these clauses may be accessed on-line at
http://www.arnet.gov or http;//farsite.hill.af.mil.
This announcement is the solicitation which will result in a firm fixedprice
contract. The Government reserves the right to award on a multiple
award or an all or none basis. All firms must be registered in the System of
Acquisition Management database @ www.sam.gov and shall be considered
for award. SAM is a mandatory requirement for all DOD Government
contracts. You must be registered in order to be eligible for award of a
contract. All quotes must be sent to SrA Jared Garner at: Fax 601-484
-9087; e-mail jared.a.garner2.mil@mail.mil; or mail directly to 186th ARW,
6225 M Street, Meridian, MS 39307-7112. Quotes are required to be received
not later than 3:30 PM CST, Friday, 31 August, 2018.
POINTS OF CONTACT; Technical questions regarding this
requirement may be addressed to SrA Jared Garner at
jared.a.garner2.mil@mail.mil. Contracting questions for this requirement
may be addressed to SrA Jared Garner at jared.a.garner2.mil@mail.mil.

.