West-Mark_Specs.pdf

Jeff Hurst 12795-0001

ODOT

09/05/24

P.O.BOX 100 PHONE: (209) 537-4747

CERES, CA 95307 TOLL FREE: (800) 692-5844

www.west-mark.com FAX: (209) 537-1753

GENERAL

The following equipment shall be a new West-Mark tandem axle semi trailer.

OVERALL LENGTH: Approximately forty-three feet six inches (43' 6").

68,000 – 70,000 gvwr depending on chassis PRODUCT: Deicing solutions VESSEL CODE: Non-Spec.

OPERATING PRESSURE: Atmosphere.

VACUUM RATING: None (0 in./Hg).

TANK OPERATING TEMPERATURE: One hundred twenty-five degrees Fahrenheit (125° F) maximum.

Negative twenty degrees Fahrenheit (-20° F) minimum.

INTENDED AREA OF OPERATION: State of Ohio.

INTENDED USE: Highway only.

PASSIVATION:

None. (Available as option upon request and may be recommended for the product specified herein)

TRACTOR

TRACTOR:

Customer supplied.

(Note: weights are based on tractor full of fuel and with driver.)

A=____ D=____ G=____ B=____ E=____ C=____ F=____

(Customer to supply chassis info. at time of order.)

If information is not supplied at time of order, West-Mark will use its standard typical setup. Any information supplied after engineering package has been released to production, that requires set-up changes, will be done at additional charge to customer.

TANK / MANHOLES / VENTING

BARREL:

5000 Gallons round, straight barrel, with slope to rear. The barrel shall be made from 12 gauge T-316/T-316L stainless steel, 2B finish material.

Capacity does not include head outage.

HEADS: Two (2) each stainless steel, T-316/ T-316L 2B, 12 gauge, 10% dished and flanged.

HEAD FINISH: Outside of heads to be spin polished.

BAFFLE(S): Two (2) each stainless steel, T-316 2B, 12 gauge, 10% dished and flanged.

RINGS: Stainless steel channel sections, fully welded to shell.

WINGS AND BOLSTERS: Shall be made of stainless steel.

SIDE FILLERS: Stainless steel with coupler plate adjustment rails.

WELD FINISH:

INTERIOR: Weld finish to be W-2 inside. All Longitudinal seams to be W-3.

EXTERIOR: Weld finish to be W-2 outside.

MANHOLE/CLEANOUT:

One (1) BETTS 20" 8310 full opening, T316L stainless steel with 6 hold downs and a hinge stop for keeping the lid off the shell when open. 43.5 psi MAWP.

Gasket to be White Hypalon.

CLEANOUT(S):

None. (Available as option upon request)

VENTING:

One (1) Each Trident, pressure actuated emergency venting, plus in breathing and out breathing, installed on a coupling in shell.

INSULATION:

None. (Available as option upon request) C.I.P.:

None. (Available as option upon request)

LADDERS / WALKWAYS / SPILLDAMS

SPILLDAM:

One (1) Each non-insulated, stainless steel box style, with drain hoses each side.

LADDER:

One (1) aluminum tubular, multi-purpose ladder assembly, with West-Mark heavy duty slip resistant steps located at roadside of unit. Step will be between 18” and 22” from the ground. No grab rails installed (available as option upon request).

SPILLDAM WALKWAY:

12" Wide aluminum non-slip platform walkway, full length of spilldam; located between ladder and spilldam.

LIGHTS AND WIRING

ELECTRICAL SYSTEM:

System shall be 12-volt, 7-way, and vapor proof. All lamps to be L.E.D. type and locations shall meet all D.O.T.

requirements.

STOP/ TAIL/ TURN: Four (4) each model 44 type in 2-hole, stainless steel boxes; 2 red each side.

CENTER ID: One (1) each Truck-Lite model 15 stainless steel I.D. shall be mounted at rear per D.O.T.

MID TURN/ MARKER: One (1) each amber model 60 oval turn/ marker light shall be mounted @ center of unit (approx.)

each side if required by D.O.T.

FRONT MARKERS: One (1) each amber model 30 light shall be mounted to the front corner of the trailer at 45° on each side of unit.

REAR MARKERS: One (1) each red model 30 marker lamp located at end of each light box.

SECURITY RINGS / MOUNT COVERS: None. (Available as option upon request)

REFLECTORS:

To be mounted per D.O.T. specifications.

CONSPICUITY STRIPING:

To be installed at sides and rear per D.O.T. specifications.

FRONT RECEPTICAL:

Truck-Lite 7-way nosebox (model #50806) with 15 amp circuit breakers and front access to cable hookup, mounted on a stainless steel bracket between glad hands.

PLUMBING

REAR OUTLET:

3" Stainless steel split pipe out rear head.

OUTLET PLUMBING:

Plumb from sump to a 3” butterfly valve with stainless steel disc and stem and lever lock handle.

Plumbing to end in 3" stainless steel male camlock adapter and lockable brass cap with chain.

TOP FILL:

None. (Available as option upon request)

UNDERCARRIAGE

KICK PLATE:

To be installed at front of unit and to be of stainless steel construction.

KING PIN PLATE:

Adjustable upper coupler, mild steel.

48" Ride height, unless noted otherwise in tractor spec's above.

LANDING GEAR FRAME:

Frame to be stainless steel construction.

LANDING LEG SUPPORTS:

Stainless steel pipe style from legs up to crossmember and to rear of subframe with lower leg supports for landing legs.

LANDING GEAR:

JOST square leg, 2-speed, steel, sand shoes, 50,000 lb. lift, 160,000 lb. static load capacity.

Crank located on curbside.

REAR SUBFRAME:

Stainless steel construction for a tandem axle suspension.

SUSPENSION:

Two (2) HENDRICKSON TURNER INTRAAX AANT 23K air ride integration system 17" ride height, weld-on wing style hangers, front shock absorbers

AXLES:

Two (2) 23K, 5-3/4" round 71-1/2" track 10 stud on 11.25" centers ConMet Preset aluminum hubs with HUB piloted mounting HP spindles (same inner and outer bearings) Chevron Delo semi fluid grease Pro Prep ® tire inflation

BRAKES:

16-1/2" X 7", 28 spline S-Cam, balanced fused drums 16.5" x 7" HXS Abex 3030-197 non-asbestos brake lining Hendrickson’s standard chambers and automatic slacks Tone rings for ABS system.

HEIGHT CONTROL (SUSPENSION SPECIFIC):

Two (2) Each height control valve.

DUMP VALVE:

Manual dump valve to be installed.

WHEELS:

OUTER: Four (4) Each 22.5 x 8.25 STEEL painted white.

INNER: Four (4) Each 22.5 x 8.25 STEEL painted white.

TIRES:

Eight (8) Each 295/75R 22.5 CONTINENTAL HT3.

TIRE INFLATION SYSTEM:

NONE

BUMPER:

Stainless steel non-code, 3" x 2" x 66" long.

(If underidement bumper is required, this item may be eliminated.)

BRAKE SYSTEM:

To be built to D.O.T. specifications, WABCO 4S/2M IABS with ROLL STABILITY system and Aluminum air tank(s). IABS malfunction/ operation light located on front fender bracket of roadside rear fender, facing forward, per D.O.T.

REAR APRON:

None. (Available as option upon request)

FRONT FENDERS:

None. (Available as option upon request)

REAR FENDERS:

Aluminum contour, ribs down.

Stainless steel fender pipe mounting with U-bolts and under straps.

Mudflaps at rear of unit to be WHITE, poly, anti-spray type. Mudflap mounting to meet SAEJ682 standard.

MISC. ITEMS

PADLOCK SECURITY SYSTEM:

None. (Available as option upon request)

LIQUID LEVEL GAUGE:

None. (Available as option upon request)

CERTIFICATE HOLDER:

Betts PS-1 (#820012) document holder with spring.

Mounted on landing leg subframe (roadside).

PAINT:

One (1) Color Acrylic Urethane paint on suspension and on all carbon steel fabricated parts.

Color to be Black

CALIBRATION:

Theoretical, in 1/4" increments, complete with charts.

MANUALS:

One (1) each operation and maintenance manual(s) on a USB Drive shall be supplied and shipped with unit;

WARRANTY:

Unit shall be guaranteed to be free from defects in material and workmanship, while under normal use and service by the original purchaser, for a period of ONE (1) year from the date unit is delivered.

F.O.B.:

Destination (CONUS).

Ship to: Multiple Ohio locations

INSPECTION AND ACCEPTANCE:

West-Mark (CAGE: 880W5) 581 Industry Way Atwater, CA 95301